Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “large area”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Role of deep levels and barrier height lowering in current-flow mechanism in 150 μ m thick epitaxial n-type 4H–SiC Schottky barrier radiation detectors

Schottky barrier detectors (SBDs) require larger surface areas than conventional electronics to increase the detection efficiency although such SBDs manifest large diode ideality factors due to inhomogeneous areal distribution of surface barrier height (SBH). Inhomogeneous SBH distributions lead to various current flow mechanisms in SBDs, which need to be identified to optimize detector performance. In this Letter, we identify the current flow mechanism in large area Schottky barrier diodes for radiation detection fabricated on 150 μm thick n-4H–SiC epitaxial layers. The analysis of temperature-dependent forward current–voltage (I–V–T) characteristics of SBDs revealed two linear regions in current–voltage curves up to 450 K, one corresponding to the current flow through a low barrier patch, while the other corresponds to that of average barrier distribution. Applying a SBH distribution model to the reverse I–V–T characteristics, an activation energy of 0.76 eV for the current flow over the Schottky barrier was calculated. Additionally, the activation energy did not directly correspond to any of the defect levels observed from the deep level transient spectroscopy (DLTS). Above 450 K, a Schottky type barrier lowering suggested a current flow through a low barrier patch of ≈ 0.8 eV. The absence of any SBH lowering below 450 K indicated that the current corresponded to a neutrally charged trap level at ≈ 0.6 eV below the conduction band edge, which was consistent with DLTS measurements revealing the presence of an electron trap level Z1/2 at 0.59 eV below the conduction band edge.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1978

Development of a process for high capacity-arc heater production of silicon

The realization of low cost, electric power from large-area silicon, photovoltaic arrays will depend on the development of new methods for large capacity production of solar grade (SG) silicon with a cost of less than $10 per kilogram by 1986 (established Department of Energy goal). The objective of the program is to develop a method to produce SG silicon in large quantities based on the high temperature-sodium reduction of silicon tetrachloride (SiCl4) to yield molten silicon and the coproduct salt vapor (NaCl). Commercial ac electric arc heaters will be utilized to provide a hyper-heated mixture of argon and hydrogen which will furnish the required process energy. The reactor is designed for a nominal silicon flow rate of 45 kg/hr. Analyses and designs have been conducted to evaluate the process and complete the initial design of the experimental verification unit.

Reed, W. H.↗
DOE OSTI2022

Perovskite Photovoltaics: Venturing Outdoors

Metal halide perovskite solar cells have shown promising performance, but mainly on small-area devices and under laboratory conditions. Now, researchers have demonstrated the fabrication of large-area devices assembled and packaged into modules and reported on their operation outdoors.

field testing↗
DOE OSTI2025

Improved heavy-ion PID using scintillation light detector with neural network analysis: a Monte Carlo simulation study

The photon collection efficiency of gaseous scintillator detectors varies according to the position of the impinging charged particles in the medium that generates scintillation light. Thus, when impinging particles are distributed over a large area, the intrinsic photon-number resolution of the system is affected by a large variation. This work presents and discusses a method for adjusting the total number of detected photons to account for variation in the photon collection efficiency as a function of the position of the light source within the scintillating medium. The method was developed and validated by processing data from systematic simulation studies based on GEANT4 that model the response of the Energy Loss Optical Scintillation System (ELOSS) detector. The position of the charged particle is calculated using a deep neural network algorithm. This is accomplished by analyzing the distribution of scintillation light recorded by the array of photosensors. The estimated particle position is then used to calculate the correction factor and adjust the amount of captured light to account for variations in the photon collection efficiency. The neural network algorithm provides excellent tracking capabilities, achieving sub-millimeter position resolution and an angular resolution of 12 mrad, approaching the performance of traditional tracking detectors (e.g., drift chambers). The present method can be generalized to any optical scintillation system where the photon collection efficiency depends on the position of the impinging particle.

Heavy-ion detectors↗
DOE OSTI2023

Evaluation of the Function of ASFV Gene E66L in the Process of Virus Replication and Virulence in Swine

African swine fever virus (ASFV) is the etiological agent of an economically important disease of swine currently affecting large areas of Africa, Eurasia and the Caribbean. ASFV has a complex structure harboring a large dsDNA genome which encodes for more than 160 proteins. One of the proteins, E66L, has recently been involved in arresting gene transcription in the infected host cell. Here, we investigate the role of E66L in the processes of virus replication in swine macrophages and disease production in domestic swine. A recombinant ASFV was developed (ASFV-G-ΔE66L), from the virulent parental Georgia 2010 isolate (ASFV-G), harboring the deletion of the E66L gene as a tool to assess the role of the gene. ASFV-G-ΔE66L showed that the E66L gene is non-essential for ASFV replication in primary swine macrophages when compared with the parental highly virulent field isolate ASFV-G. Additionally, domestic pigs infected with ASFV-G-ΔE66L developed a clinical disease undistinguishable from that produced by ASFV-G. Therefore, E66L is not involved in virus replication or virulence in domestic pigs.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2025

Deletion of the African Swine Fever Virus Gen I196L in the Georgia2010 Isolate Genome Does Not Affect Virus Replication or Virulence in Domestic Pigs

African swine fever (ASF) is a lethal disease of domestic pigs that is currently challenging swine production in large areas of Eurasia and the Caribbean. The causative agent, ASF virus (ASFV), is a large, double-stranded, and structurally complex virus. The ASFV genome encodes for more than 160 proteins; however, the functions of most of them are still in the process of being characterized. Recently, ASFV gene I196L has been reported as being critically involved in disease production in domestic pigs. We report here that a recombinant virus derived from the Georgia 2010 isolate (ASFV-G) lacking the I196L gene, ASFV-G-∆I196L, had the same ability to replicate in primary cultures of swine macrophage and, when experimentally inoculated in pigs, produced a fatal form of the disease similar to that caused by the parental virulent ASFV-G. Therefore, deletion of the I196L gene does not significantly affect virus replication and virulence in domestic pigs of the ASFV Georgia 2010 isolate.

Virology↗
NASA NTRS1979

A query into the source of proton emission from solar flares, report 2

Seven solar flares that were followed by major proton events were examined to determine the diverse and common properties of major flares. The most probable site of primary proton acceleration is cospatial with the site and instant of formation of coronal loops. Because loop formation occurs through the entire duration of major solar flares over significantly large areas of active centers, it is proposed that proton injection occurs from a relatively large volume of space in the corona of active centers and is continuous throughout, and possibly even after, the visible duration of the related chromospheric flare. The flare veil is hypothesized to occur as a result of proton charge exchange taking place in the white-light transient. The Kopp and Pneuman model of loop formation by magnetic reconnection is suggested as an adequate and satisfactory model for all major flares with the provision that the beginning of rapid magnetic field reconnection is coincident with flare start.

Martin, S. F.↗
NASA NTRS1990

Regional aeolian dynamics and sand mixing in the Gran Desierto - Evidence from Landsat Thematic Mapper images

Mesoscale mapping of spatial variations in sand composition of the Gran Desierto (Sonora, Mexico) was carried out on multispectral Landsat TM images of this region, making it possible to examine the dynamic development of sand sheets and dunes. Compositions determined from remote imagery were found to agree well with samples from selected areas. The sand populations delineated were used to describe the sediment source areas, transport paths, and deposition sites. The image analysis revealed important compositional variations aver large areas that were not readily apparent in the field data.

Blount, Grady↗
NASA NTRS2023

Using Satellite Data to Characterize Land Surface Processes in Morocco

This study endeavors to produce a comprehensive land cover map for Morocco, addressing the absence of such a detailed map in the country. Our research encompasses ecological and climatic aspects specific to Morocco, while the methods used can be adapted to various regions and countries, considering their unique climatic conditions and land cover types. A combination of MODIS and Landsat datasets was employed to create a 5 km resolution Land Use and Land Cover (LULC) map for the entire nation. The process involved the aggregation and advanced processing of these datasets using surface processes algorithms. The resulting LULC map is the first of its kind for Morocco, shedding light on land cover distribution nationwide. It shows that approximately 13.5% of the country is covered by forests, predominantly in the Atlas and Rif mountains, Rabat–Sale, and the southern regions. Grasslands occupy over 16% of the study area, mainly in the north-east and west. Urban areas, including major cities like Casablanca, Rabat, and Marrakech, span nearly 3400 km². Moreover, large areas of shrublands and bare lands are evident across the country, while agricultural lands account for almost 20% of the national territory, mainly in the interior plains and north-western Atlantic coast. This study forms a crucial basis for ecological and climatic research in Morocco and serves as a valuable reference for various disciplines such as agriculture, natural resource management, and climate modeling. The mapping of biophysical parameters for each land cover class is a key feature of our research, and these parameters will be instrumental in a subsequent study examining the impact of urban development on surface climate in Morocco. Overall, our study underscores the importance of understanding biophysical parameters in addressing environmental and societal challenges.

Mohammed Thaiki↗
NASA NTRS2000

Generating Accurate Urban Area Maps from Nighttime Satellite (DMSP/OLS) Data

There has been an increasing interest by the international research community to use the nighttime acquired "city-lights" data sets collected by the US Defense Meteorological Satellite Program's Operational Linescan system to study issues relative to urbanization. Many researchers are interested in using these data to estimate human demographic parameters over large areas and then characterize the interactions between urban development , natural ecosystems, and other aspects of the human enterprise. Many of these attempts rely on an ability to accurately identify urbanized area. However, beyond the simple determination of the loci of human activity, using these data to generate accurate estimates of urbanized area can be problematic. Sensor blooming and registration error can cause large overestimates of urban land based on a simple measure of lit area from the raw data. We discuss these issues, show results of an attempt to do a historical urban growth model in Egypt, and then describe a few basic processing techniques that use geo-spatial analysis to threshold the DMSP data to accurately estimate urbanized areas. Algorithm results are shown for the United States and an application to use the data to estimate the impact of urban sprawl on sustainable agriculture in the US and China is described.

Imhoff, Marc↗
DOE OSTI2023

Scalable aqueous-phase fabrication of reduced graphene oxide nanofiltration membranes by an integrated roll-to-roll (R2R) process

Economic fractionation of multicomponent biomass-derived streams is a key challenge in biobased fuels and chemicals production. Kraft black liquor (BL) is generated at ~1 billion tons/yr globally from biomass pulping and contains ~15wt% total solids including lignin, hemicellulose fragments, and inorganics. Membrane-based BL concentration is attractive but challenged by low solute rejections and poor stability in BL, which combines alkaline pH (~13), high dissolved solids content (15+ wt%) and high temperature (70–85°C). Here we discuss the scaled fabrication and characterization of reduced graphene oxide (rGO) nanofiltration membranes by slot die coating on a roll-to-roll (R2R) with integrated vacuum filtration. Here, we obtain high-quality 90×30 cm rGO membranes (referred to as “R2R-rGO membranes” in this work) with ~100 nm average thickness supported on porous poly(ethersulfone) (PES) sheets, and an effective area of 2700cm 2 . We present characterizations of their microstructure and uniformity as mapped over large areas by scanning electron microscopy (SEM), ellipsometry, adhesion test and X-ray photoelectron spectroscopy (XPS). The constructed ellipsometry model for the rGO membrane/PES substrate composite was successfully applied to 48 different locations of the R2R-rGO membranes. The R2R-rGO membranes showed >98% lignin rejection with a steady state flux of ~12 LMH at 50bar in a 15.7wt% total solids (TS) kraft BL stream at 72°C and 2–3 gal/min crossflow rates. Slot die coating on a R2R platform with integrated vacuum filtration can enable rapid fabrication of high-quality GO membranes at scale without organic solvents or volatile organic compounds.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Construction status of the Mu2e crystal calorimeter

The Mu2e experiment at Fermilab will search for the charged-lepton flavor violating neutrino-less conversion of a negative muon into an electron in the field of an aluminum nucleus. The Mu2e detector is composed of a tracker, an electromagnetic calorimeter and an external veto for cosmic rays. The calorimeter plays an important role in providing excellent particle identification capabilities and a fast online trigger filter, while aiding the track reconstruction capabilities. Calorimeter requirements are to provide a large acceptance for 0~10 MeV electrons and reach: i) a time resolution better than 0.5 ns; ii) an energy resolution better than 10%; and iii) a position resolution of 1 cm. The calorimeter consists of two disks, each one made of 674 pure CsI crystals. Each crystal is readout by two large area 2×3 arrays of UV-extended SiPMs of 6×6 mm2 dimensions. A large scale prototype (Module-0) has been tested at an electron beam. We report here the tests done to finalize the calorimeter design, the results obtained with Module-0 and the status of production. At this time, the performance characteristics of 85% of the crystals and all of the SiPMs have been measured. The calorimeter engineering drawings have been completed and the large mechanical components are under fabrication. Analog and digital electronics have been prototyped and tested with irradiation dose. Their serial production is being organized. The calorimeter assembly phase is planned for mid-2020.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS2004

Advances in Structures for Large Space Systems

The development of structural systems for scientific remote sensing and space exploration has been underway for four decades. The seminal work from 1960 to 1980 provided the basis for many of the design principles of modern space systems. From 1980- 2000 advances in active materials and structures and the maturing of composites technology led to high precision active systems such those used in the Space Interferometry Mission. Recently, thin-film membrane or gossamer structures are being investigated for use in large area space systems because of their low mass and high packaging efficiency. Various classes of Large Space Systems (LSS) are defined in order to describe the goals and system challenges in structures and materials technologies. With an appreciation of both past and current technology developments, future technology challenges are used to develop a list of technology investments that can have significant impacts on LSS development.

Belvin, W. Keith↗
NASA NTRS2012

A Statistical Approach to Recognizing Source Classes for Unassociated Sources in the First FERMI-LAT Catalog

The Fermi Large Area Telescope (LAT) First Source Catalog (1FGL) provided spatial, spectral, and temporal properties for a large number of gamma -ray sources using a uniform analysis method. After correlating with the mostcomplete catalogs of source types known to emit gamma rays, 630 of these sources are "unassociated" (i.e., have no obvious counterparts at other wavelengths). Here, we employ two statistical analyses of the primary gamma-ray characteristics for these unassociated sources in an effort to correlate their gamma-ray properties with the active galactic nucleus (AGN) and pulsar populations in 1FGL. Based on the correlation results, we classify 221 AGN-like and 134 pulsar-like sources in the 1FGL unassociated sources. The results of these source "classifications" appear to match the expected source distributions, especially at high Galactic latitudes. While useful for planning future multiwavelength follow-up observations, these analyses use limited inputs, and their predictions should not be considered equivalent to "probable source classes" for these sources. We discuss multiwavelength results and catalog cross-correlations to date, and provide new source associations for 229 Fermi-LAT sources that had no association listed in the 1FGL catalog. By validating the source classifications against these new associations, we find that the new association matches the predicted source class in approximately 80% of the sources.

SOURCES↗
NASA NTRS2019

Use of Very High-Resolution Optical Data for Landslide Mapping and Susceptibility Analysis Along the Karnali Highway, Nepal

The Karnali highway is a vital transport link and the only primary roadway that connects the remote Karnali region to the lowlands in Mid-Western Nepal. Every year there are reports of landslides blocking the road, making this area largely inaccessible. However, little effort has focused on systematically identifying landslides and landslide-prone areas along this highway. In this study, landslides were mapped with an object-based approach from very high-resolution optical satellite imagery obtained by the DigitalGlobe constellation in 2012 and PlanetScope in 2018. Landslides ranging from 10 to 30,496 sq.m were detected within a 3 km buffer along the highway. Most of the landslides were located at lower elevations (between 500–1500 m) and on steep south-facing slopes. Landslides tended to cluster closer to the highway, near drainage channels and away from faults. Landslides were also most prevalent within the Kuncha Formation geologic class, and the forested and agricultural land cover classes. A susceptibility map was then created using a logistic regression methodology to highlight patterns in landslide activity. The landslide susceptibility map showed a good prediction rate with an area under the curve (AUC) of 0.90. A total of 33% of the study arealies in high/very high susceptibility zones. The map highlighted the lower elevated areas between Bangesimal and Manma towns with the Kuncha Formation geologic class as being the most hazardous. The banks of the Karnali River, its tributaries and areas near the highway were also highly susceptible to landslides. The results highlight the potential of very high-resolution optical imagery for documenting detailed spatial information on landslide occurrence, which enables susceptibility assessment in remote and data scarce regions such as the Karnali highway.

Pukar Amatya↗
DOE OSTI2022

The Presence of Virus Neutralizing Antibodies Is Highly Associated with Protection against Virulent Challenge in Domestic Pigs Immunized with ASFV live Attenuated Vaccine Candidates

African swine fever virus (ASFV) is currently producing a pandemic affecting a large area of Eurasia, and more recently, the Dominican Republic in the Western Hemisphere. ASFV is a large and structurally complex virus with a large dsDNA genome encoding for more than 150 genes. Live attenuated virus strains can induce protection in domestic swine against disease produced by homologous virulent parental viruses. The roles of the different immune mechanisms induced by the attenuated strains in protection still need to be understood. In particular, the role of ASFV neutralizing antibody in protection still is an important controversial issue to be elucidated. Here we present the development of a novel methodology to detect virus neutralizing antibodies based on the reduction of virus infectivity in a Vero cell adapted ASFV strain. The described method was used to assess levels of virus neutralizing antibodies in domestic swine inoculated with live attenuated ASFV. Results demonstrated a high association between the presence of virus neutralizing antibodies and protection in 84 animals immunized with the recombinant vaccine candidates ASFV-G-Δ9GL/ΔUK or ASFV-G-ΔI177L. To our knowledge, this is the first report demonstrating an association between virus neutralizing antibodies and protection against virulent challenge in such a large number of experimental individuals.

59 BASIC BIOLOGICAL SCIENCES↗
NASA NTRS1978

Aerothermodynamic assessment of corrugated panel thermal protection systems

The results of an analysis of wind-tunnel data for the effect of wave shape on local boundary layer flows and heat transfer are used to assess the feasibility of using corrugated panels on a Single-Stage-To-Orbit (SSTO) vehicle. In the flight assessment, available engineering design procedures are used to compute the inviscid and boundary layer flow for a given flight trajectory. The flight vehicle flow field calculations are then used in conjunction with wind-tunnel corrugated panel heating data correlations to examine the heating penalties associated with using corrugated panels at a number of locations on the vehicle. Severe heating penalties, as a result of the corrugations, were found over large areas of the windward surface. Maximum surface temperature penalties ranged from 100K to 500K and very large structural advantages for the corrugations would be required to override the heating penalties. Computed peak corrugation temperatures were within allowable limits of the equivalent smooth wall material for most leeward and side fuselage locations and corrugated panels will be most likely limited to these locations.

Brandon, H. J.↗
NASA NTRS1978

Soil moisture estimation using reflected solar and emitted thermal infrared radiation

Classical methods of measuring soil moisture such as gravimetric sampling and the use of neutron moisture probes are useful for cases where a point measurement is sufficient to approximate the water content of a small surrounding area. However, there is an increasing need for rapid and repetitive estimations of soil moisture over large areas. Remote sensing techniques potentially have the capability of meeting this need. The use of reflected-solar and emitted thermal-infrared radiation, measured remotely, to estimate soil moisture is examined.

Jackson, R. D.↗