Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “kW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Measured effect of wind generation on the fuel consumption of an isolated diesel power system

The Block Island Power Company (BIPCO), on Block Island, Rhode Island, operates an isolated electric power system consisting of diesel generation and an experimental wind turbine. The 150-kW wind turbine, designated MOD-OA by the U.S. Department of Energy is typically operated in parallel with two diesel generators to serve an average winter load of 350 kW. Wind generation serves up to 60 percent of the system demand depending on wind speed and total system load. Results of diesel fuel consumption measurements are given for the diesel units operated in parallel with the wind turbine and again without the wind turbine. The fuel consumption data are used to calculate the amount of fuel displaced by wind energy. Results indicate that the wind turbine displaced 25,700 lbs. of the diesel fuel during the test period, representing a calculated reduction in fuel consumption of 6.7 percent while generating 11 percent of the total electric energy. The amount of displaced fuel depends on operating conditions and system load. It is also shown that diesel engine throttle activity resulting from wind gusts which rapidly change the wind turbine output do not significantly influence fuel consumption.

Stiller, P. H.↗
NASA NTRS1983

Wind turbine generator interaction with diesel generators on an isolated power system

The results of a dynamic interaction investigation to characterize any disturbances caused by interfacing the Mod 0A wind turbine (150 kW configuration) with the Block Island utility diesel generator grid are reported. The tests were run when only two diesel generators were on line, and attention was given to power, frequency, and voltage time profiles. The interconnected system was examined in the start-up and synchronization phase, normal shutdown and cut-out of the wind turbine, during fixed pitch generation, and during variable pitch operation. Governors were installed on the diesel generators to accommodate the presence of wind-derived electricity. The blade pitch control was set to maintain power at 150 kW or below. Power and voltage transients were insignificant during start-up and shutdown, and frequency aberrations were within the range caused by load fluctuations. It is concluded that wind turbine generation can be successfully implemented by an isolated utility, even with a significant penetration to the total grid output.

Scott, G. W.↗
NASA NTRS1984

Parametric analysis of hollow conductor parallel and coaxial transmission lines for high frequency space power distribution

A parametric analysis was performed of transmission cables for transmitting electrical power at high voltage (up to 1000 V) and high frequency (10 to 30 kHz) for high power (100 kW or more) space missions. Large diameter (5 to 30 mm) hollow conductors were considered in closely spaced coaxial configurations and in parallel lines. Formulas were derived to calculate inductance and resistance for these conductors. Curves of cable conductance, mass, inductance, capacitance, resistance, power loss, and temperature were plotted for various conductor diameters, conductor thickness, and alternating current frequencies. An example 5 mm diameter coaxial cable with 0.5 mm conductor thickness was calculated to transmit 100 kW at 1000 Vac, 50 m with a power loss of 1900 W, an inductance of 1.45 micron and a capacitance of 0.07 micron-F. The computer programs written for this analysis are listed in the appendix.

Jeffries, K. S.↗
NASA NTRS1984

Design of a 1-kWh bipolar nickel hydrogen battery

The design of a nickel hydrogen battery utilizing bipolar construction in a common pressure vessel is discussed. Design features are as follows: 40 ampere-hour capcity, 1 kWh stored energy as a 24 cell battery, 1.8 kW delivered in a LEO Cycle and maximum pulse power of 18.0 kW.

Cataldo, R. L.↗
NASA NTRS1983

Review of specific antenna configurations: An estimate of cost and performance versus frequency for a simple (10 Lambda)-2 clear-air radar antenna array

The building of operational clear air radar wind profilers is discussed. The choice of operating frequency and antenna configuration for these profilers is examined. The cost and performance of a (10 lambda) 2 antenna array versus operating frequency over the range 30 to 400 MHz is compared. To simplify the comparison the array beam will be fixed and the array will be uniformly fed. Yagi and coaxial collinear (COCO) cable antennas are compared, although other configurations may be competitive. It is assumed that the array is driven by a typical 50 kW peak power, 1 kW average, power transmitter located at the array edge when calculating feedline power handling requirements and when system performance is compared. For this comparison an array aperture of (10 lambda) 2 was chosen since a one way beam width of 5 deg or less is desirable to limit beam spreading effects.

Ecklund, W. L.↗
NASA NTRS1984

Develop and test fuel cell powered on-site integrated total energy systems

On-going testing of an 11 cell, 10.7 in. x 14 in. stack (about 1 kW) reached 2600 hours on steady load. Nonmetallic cooling plates and an automated electrolyte replenishment system continued to perform well. A 10 cell, 10.7 in. x 14 in. stack was constructed with a modified electrolyte matrix configuration for the purpose of reducing cell IR loss. The desired effect was achieved, but the general cell performance level was irregular. Evaluation is continuing. Preparations for a long term 25 cell, 13 in. x 23 in. test stack (about 4 kW) approached completion. Start up in early May 1984 is expected.

Kaufman, A.↗
NASA NTRS1983

Space station needs, attributes, and architectural options: Mission requirements

Space station missions and their requirements are discussed. Analyses of the following four mission categories are summarized: (1) commercial, (2) technology, (3) operation, and (4) science and applications. The requirements determined by the study dictate a very strong need for a manned space station to satisfy the majority of the missions. The station is best located at a 28.5-deg inclination and initially (1992 era) requires a crew of four (three for mission payloads) and a mission power of 25 kW. A space platform in a polar orbit is needed to augment the station capability; it initially would be a 15-kW system, located in a sun-synchronous orbit.

Riel, F. D.↗
NASA NTRS1984

Near-term Brayton Module Status

The integration of subsystem components and the testing of a Parabolic Dish Module (PDM) to convert solar energy to grid compatible electric power is examined. System components are selected on a basis of current and projected performance efficiencies, technology readiness, future production probabilities and prices, current cost and availability. Potential for a near-term, 8 kW derivative of the PDM is adjudged to be superior to that of a 20 kW system. The PDM is suited to both grid connected and standalone applications, and it may be fired by solar, fossil, or solar/fossil hydrid means.

Davis, S. B.↗
NASA NTRS1982

Application of beam power technology to a space station

The feasibility and performance parameters for beam microwave power supplies from a space station to nearby orbiting satellites are examined. A 5.8 GHz transmission frequency is found suitable for beaming 1-10 kW over a distance of 1-10 km. The antenna could have a 15 m diameter, a 64 kW output, provide uniform illumination, and have a retrodirective phase control system. A LEO to ground demonstration project is described, involving power levels of 0.0025 mW/sq cm and yielding 202 W at a 100 x 100 m rectenna.

Arndt, G. D.↗
NASA NTRS1983

Advanced electrical power system technology for the all electric aircraft

The application of advanced electric power system technology to an all electric airplane results in an estimated reduction of the total takeoff gross weight of over 23,000 pounds for a large airplane. This will result in a 5 to 10 percent reduction in direct operating costs (DOC). Critical to this savings is the basic electrical power system component technology. These advanced electrical power components will provide a solid foundation for the materials, devices, circuits, and subsystems needed to satisfy the unique requirements of advanced all electric aircraft power systems. The program for the development of advanced electrical power component technology is described. The program is divided into five generic areas: semiconductor devices (transistors, thyristors, and diodes); conductors (materials and transmission lines); dielectrics; magnetic devices; and load management devices. Examples of progress in each of the five areas are discussed. Bipolar power transistors up to 1000 V at 100 A with a gain of 10 and a 0.5 microsec rise and fall time are presented. A class of semiconductor devices with a possibility of switching up to 100 kV is described. Solid state power controllers for load management at 120 to 1000 V and power levels to 25 kW were developed along with a 25 kW, 20 kHz transformer weighing only 3.2 kg. Previously announced in STAR as N83-24764

Finke, R. C.↗
NASA NTRS1983

Automotive Stirling Engine Development Program Mod I Stirling engine development

The development of the Mod I 4-cylinder automotive Stirling engine is discussed and illustrated with drawings, block diagrams, photographs, and graphs and tables of preliminary test data. The engine and its drive, cold-engine, hot-engine, external-heat, air/fuel, power-control, electronic-control, and auxiliary systems are characterized. Performance results from a total of 1900 h of tests on 4 prototype engines include average maximum efficiency (at 2000 rpm) 34.5 percent and maximum output power 54.4 kW. The modifications introduced in an upgraded version of the Mod I are explained; this engine has maximum efficiency 40.4 percent and maximum power output 69.2 kW.

Simetkosky, M. A.↗
NASA NTRS1984

Development and evaluation of a plasma jet flameholder for scramjets

The objective of the work reported herein was to explore the use of a continuous operation plasma torch as an ignitor and flameholder for scramjet combustion. This research was motivated by the desire to eliminate the use of pyrophoric or toxic ignition and/or combustion enhancement materials in operational aircraft or shipboard systems. The total temperatures and torch powers used to ignite/flamehold Mach 2 combustion with hydrogen, ethylene, ethane, and methane were determined. The minimum ignition total temperatures for the fuels tested were hydrogen - 1065 R (lowest test temperature); ethylene - 1500 R; ethane - 2000 R; methane - 2700 R. These temperatures were obtained while operating the torch at a nominal 2 kw net power. The torch was shown to be a good ignitor and flameholder in that both hydrogen and hydrocarbon fuels could be stabilized by the torch and would 'blow off' when the torch was extinguished. The effectiveness of the torch was very sensitive to relative fuel injection location. Best combustion resulted when fuel was injected both upstream and downstream of the torch. These results indicated that an adiabatic plasma torch operating at about 2 kw could be an effective ignitor and flameholder for high-speed combustion.

Northam, G. B.↗
NASA NTRS1984

The atmosphere of Mars - Resources for the exploration and settlement of Mars

This paper describes methods of processing the Mars atmosphere to supply water, oxygen and buffer gas for a Mars base. Existing life support system technology is combined with innovative methods of water extraction, and buffer gas processing. The design may also be extended to incorporate an integrated greenhouse to supply food, oxygen and water recycling. It is found that the work required to supply one kilogram of an argon/nitrogen buffer gas is 9.4 kW-hr. To extract water from the dry Martian atmosphere can require up to 102.8 kW-hr per kilogram of water depending on the relative humidity of the air.

Meyer, T. R.↗
NASA NTRS1984

Design, development and test of a capillary pump loop heat pipe

The development of a capillary pump loop (CPL) heat pipe, including computer modeling and breadboard testing, is presented. The computer model is a SINDA-type thermal analyzer, combined with a pressure analyzer, which predicts the transients of the CPL heat pipe during operation. The breadboard is an aluminum/ammonia transport system which contains multiple parallel evaporator and condenser zones within a single loop. Test results have demonstrated the practicality and reliability of such a design, including heat load sharing among evaporators, liquid inventory/temperature control feature, and priming under load. Transport capability for this system is 65 KW-M with individual evaporator pumps managing up to 1.7 KW at a heat flux of 15 W/sq cm. The prediction of the computer model for heat transport capabilities is in good agreement with experimental results.

Kroliczek, E. J.↗
NASA NTRS1985

Remote Power Controllers For High-Power dc Switching

Circuits combine functions of remotely controlled switch and circuit breaker. Circuits developed at different power levels but conceptually very similar. Selection of appropriate switching devices and minor modifications, circuits used to build RPC's covering range of voltage and power levels limited only by switching devices chosen. RPC's using GTO's have power capability ranging from 7.8 to 52 kW, while those using MOSFET's range from 8 to 15 kW. Applications include satellite, Space Station, commerical aircraft, naval vessels, and numerous industrial areas.

Sturman, J. C.↗
NASA NTRS1984

Investigation of a pulsed electrothermal thruster system

The performance of an ablative wall Pulsed Electrothermal (PET) thruster is accurately characterized on a calibrated thrust stand, using polyethylene propellant. The thruster is tested for four configurations of capillary length and pulse length. The exhaust velocity is determined with twin time-of-flight photodiode stagnation probes, and the ablated mass is measured from the loss over ten shots. Based on the measured thrust impulse and the ablated mass, the specific impulse varies from 1000 to 1750 seconds. The thrust to power varies from .05 N/kW (quasi-steady mode) to .10 N/kW (unsteady mode). The thruster efficiency varies from .56 at 1000 seconds to .42 at 1750 seconds. A conceptual design is presented for a 40 kW PET propulsion system. The point design system performance is .62 system efficiency at 1000 seconds specific impulse. The system's reliability is enhanced by incorporating 20, 20 kW thruster modules which are fired in pairs. The thruster design is non-ablative, and uses water propellant, from a central storage tank, injected through the cathode.

Burton, R. L.↗
NASA NTRS1984

Analytical Modeling of Spacecraft Power Systems

During the 25 years of space flight with unmanned Earth orbiting satellites, there has been an evolution of power systems in three general areas. The size of power system in terms of power demand at the bus has increased frorm a few watts in the early 1960s to a few hundred watts during the 1970s. Today, the bus power requirements are typically in the .5 to 1 kw range with some mission requirements exceeding the 1 kw size. Power grounding and user isolation are major design considerations when high fidelity power is required by a user.

Ford, F. E.↗
NASA NTRS1984

Investigation of light source and scattering medium related to vapor-screen flow visualization in a supersonic wind tunnel

Methods for increasing the radiant in light sheets used for vapor screen set-ups were investigated. Both high-pressure mercury arc lamps and lasers were considered. Pulsed operation of the air-cooled 1-kW lamps increased the light output but decreased reliability. An ellipsoidal mirror improved the output of the air-cooled lamps by concentrating the light but increased the complexity of the housing. Water-cooled-4-kW lamps coupled with high-aperture Fresnel lenses provided reasonable improvements over the air-cooled lamps. Fanned laser beams measurements of scattered light versus dew point made in conjunction with successful attempts to control the fluid injection. A number of smoke generators are described and test results comparing smoke and vapor screens are shown. Finally, one test included a periscope system to relay the image to a camera outside the flow.

Snow, W. L.↗