Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “insertion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Fundamental damper power calculation of the 56MHz SRF cavity for RHIC

At each injection period during RHIC's operation, the beam's frequency sweeps across a wide range, and some of its harmonics will cross the frequency of the 56MHz SRF cavity. To avoid excitation of the cavity at these times, we designed a fundamental damper for the quarter-wave resonator to damp the cavity heavily. The power extracted by the fundamental damper should correspond to the power handling ability of the system at all stages. In this paper, we discuss the power output from the fundamental damper when it is fully extracted, inserted, and any intermediate point. A Fundamental Damper (FD) will greatly reduce the cavity's Q factor to {approx}300 during the acceleration phase of the beam. However, when the beam is at store and the FD is removed, the cavity is excited by both the yellow and the blue beams at 2 x 0.3A to attain the required 2MV voltage across its gap. The cavity then is operated to increase the luminosity of the RHIC experiments. Table 1 lists the parameters of the FD. Figure 1 shows the configuration of the FD fully inserted into the 56MHz SRF cavity; this complete insertion is defined as the start location (0cm) of FD simulation, an assumption we make throughout this paper. The power consumed by the cavity while maintaining the beam's energy and its orbit is compensated by the 28MHz accelerating cavities in the storage ring. The power dissipation of the external load is dynamic with respect to the position of the FD during its extraction. As a function of the external Q and the EM field in the cavity, the power should peak with the FD at a certain vertical location. Our calculation of the power extracted is detailed in the following sections. Figure 2 plots the frequency change in the cavity, and the external Q against the changes in position of the FD. The location of the FD is selected carefully such that the frequency will approach the designed working point from the lower side only. The loaded Q of the cavity is 223 when the FD is fully inserted. The simulation was carried out with Microwave Studio 2010.

43 PARTICLE ACCELERATORS↗

LOW HORIZONTAL BETA FUNCTION IN LONG STRAIGHTS OF THE NSLS-II LATTICE

The NSLS-II storage ring lattice is comprised of 30 DBA cells arranged in 15 superperiods. There are 15 long straight sections (9.3m) for injection, RF and insertion devices and 15 short straights (6.6m) for insertion devices. In the baseline lattice, the short straights have small horizontal and vertical beta functions but the long straights have large horizontal beta function optimized for injection. In this paper, we explore the possibility of maintaining three long straights with large horizontal beta function while providing the other 12 long straights with smaller horizontal beta function to optimize the brightness of insertion devices. Our study considers the possible linear lattice solutions as well as characterizing the nonlinear dynamics. Results are reported on optimization of dynamic aperture required for good injection efficiency and adequate Touschek lifetime. This paper discusses dynamic aperture optimization for the NSLS-II lattice with alternate high and low horizontal beta function in the long straights, which is proposed for the optimization of the brightness of insertion devices. The linear optics is optimized to meet the requirements of lattice function and source properties. Nonlinear optimization for a lattice with working point at (37.18, 16.2) is performed. Considering the realistic magnets errors and physical apertures, we calculate the frequency maps and plot the tune footprint. The results show that the lattice with high-low beta function has adequate dynamic aperture for good injection efficiency and sufficient Touschek lifetime.

43 PARTICLE ACCELERATORS↗

Comparison of Three Cre-LoxP Based Paired-End Library Construction Methods

Paired-end library sequencing has been proven useful in scaffold construction during de novo whole genome shotgun assembly. The ability of generating mate pairs with > 8 Kb insert sizes is especially important for genomes containing long repeats. To make mate paired libraries for next generation sequencing, DNA fragments need to be circularized to bring the ends together. There are several methods that can be used for DNA circulation, namely ligation, hybridization and Cre-LoxP recombination. With higher circularization efficiency with large insert DNA fragments, Cre-LoxP recombination method generally has been used for constructing >8 kb insert size paired-end libraries. Second fragmentation step is also crucial for maintaining high library complexity and uniform genome coverage. Here we will describe the following three fragmentation methods: restriction enzyme digestion, random shearing and nick translation. We will present the comparison results for these three methods. Our data showed that all three methods are able to generate paired-end libraries with greater than 20 kb insert. Advantages and disadvantages of these three methods will be discussed as well.

99 GENERAL AND MISCELLANEOUS↗

Genetic Control of Plant Root Colonization by the Biocontrol agent, Pseudomonas fluorescens

Plant growth promoting rhizobacteria (PGPR) are a critical component of plant root ecosystems. PGPR promote plant growth by solubilizing inaccessible minerals, suppressing pathogenic microorganisms in the soil, and directly stimulating growth through hormone synthesis. Pseudomonas fluorescens is a well-established PGPR isolated from wheat roots that can also colonize the root system of the model plant, Arabidopsis thaliana. We have created barcoded transposon insertion mutant libraries suitable for genome-wide transposon-mediated mutagenesis followed by sequencing (TnSeq). These libraries consist of over 105 independent insertions, collectively providing loss-of-function mutants for nearly all genes in the P.fluorescens genome. Each insertion mutant can be unambiguously identified by a randomized 20 nucleotide sequence (barcode) engineered into the transposon sequence. We used these libraries in a gnotobiotic assay to examine the colonization ability of P.fluorescens on A.thaliana roots. Taking advantage of the ability to distinguish individual colonization events using barcode sequences, we assessed the timing and microbial concentration dependence of colonization of the rhizoplane niche. These data provide direct insight into the dynamics of plant root colonization in an in vivo system and define baseline parameters for the systematic identification of the bacterial genes and molecular pathways using TnSeq assays. Having determined parameters that facilitate potential colonization of roots by thousands of independent insertion mutants in a single assay, we are currently establishing a genome-wide functional map of genes required for root colonization in P.fluorescens. Importantly, the approach developed and optimized here for P.fluorescens>A.thaliana colonization will be applicable to a wide range of plant-microbe interactions, including biofuel feedstock plants and microbes known or hypothesized to impact on biofuel-relevant traits including biomass productivity and pathogen resistance.

Cole, Benjamin J.↗

Non-hydrolytic metal oxide films for perovskite halide overcoating and stabilization

A method of protecting a perovskite halide film from moisture and temperature includes positioning the perovskite halide film in a chamber. The chamber is maintained at a temperature of less than 200 degrees Celsius. An organo-metal compound is inserted into the chamber. A non-hydrolytic oxygen source is subsequently inserted into the chamber. The inserting of the organo-metal compound and subsequent inserting of the non-hydrolytic oxygen source into the chamber is repeated for a predetermined number of cycles. The non-hydrolytic oxygen source and the organo-metal compound interact in the chamber to deposit a non-hydrolytic metal oxide film on perovskite halide film. The non-hydrolytic metal oxide film protects the perovskite halide film from relative humidity of greater than 35% and a temperature of greater than 150 degrees Celsius, respectively.

36 MATERIALS SCIENCE↗

Ceramic matrix composite (CMC) hollow blade and method of forming CMC hollow blade

A ceramic matrix composite (CMC) hollow blade includes a CMC airfoil, which includes at least one airfoil CMC ply, at least one cavity CMC ply, and an insert. The airfoil CMC ply defines the contour of the CMC airfoil including a first edge, a second edge opposite the first edge, a first side extending from the first edge to the second edge, and a second side opposite the first side. The cavity CMC ply defines a cavity within the CMC airfoil. The insert is located between the first edge and the cavity. The insert is wrapped by a CMC ply such that the CMC ply extends along the insert from the first side of the CMC airfoil across the mean camber line of the CMC airfoil and to the second side of the CMC airfoil. The CMC ply terminates on the second side of the CMC airfoil.

36 MATERIALS SCIENCE↗

GNF fuel technology update

In 2015, Global Nuclear Fuel (GNF) launched the GNF3 fuel design by inserting lead-use assemblies into two boiling water reactors (BWRs) in the U.S. A lead use assembly is a nuclear fuel assembly which is inserted in a reactor core to confirm its performance. A third set of GNF3 lead-use assemblies are scheduled to be inserted into another reactor in the spring of 2017. GNF3 is a robust next-generation 10*10 fuel design that will improve both fuel cycle and fuel reliability. In addition, GNF3 will be delivered in a fully assembled condition - forgoing the need to insert fuel channels over the bundles at the site. The process of shipping BWR fuel in a channeled configuration is complex and requires an understanding of the potential high-cycle and low-cycle fatigue conditions that can occur during shipping, as characterized by accelerometer data from ship tests. The key component in evaluating channeled fuel shipping is the spacer, and the GNF3 spacer fatigue performance was found to be approximately twice that of GNF2. While fuel reliability has traditionally been related to the avoidance of fuel leakers, for the past 15 years channel - control blade interference has been a close second for concern. To eliminate this problem, GNF3 will come standard with NSF (a zirconium alloy) channels that are effectively resistant to fluence gradient-induced bow and shadow corrosion-induced bow. In addition to the development of GNF3, GNF is evaluating the use of advancing 3D metal printing or additive manufacturing for manufacturing fuel bundle components. Additive manufacture offers the hope of more flexibility in design and shorter manufacturing development cycles. However, since there is little experience with this technology in the nuclear industry, GNF has been evaluating the use of additive manufacture to fabricate small scale components that are easily retrieved from the reactor for testing. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Ultra-compact configurable double-sided manifold micro-channel cold plate

A configurable, double sided, manifold micro-channel cold plate includes a one or more manifold micro-channel cold plate cells. Each cold plate cell includes a manifold body, a manifold insert, a plurality of heat sinks, and a plurality of longitudinal openings configured for fluidic communication with the fluid channels. The manifold body has fluid channels to permit flow of a fluid coolant. The manifold insert has a plurality of manifold insert fluid channels, and is configured for receipt in the one of the modular body recesses. The heat sinks are configured for receipt in the modular body recesses, and include an impingement surface configured for fluidic communication with the manifold insert fluid channels, and a heat transfer surface for thermal communication with one or more heat generating devices.

Zhou, Feng↗

Combining RHF and HFIR Disposition Campaigns - Analysis, Opportunity, and Lessons Learned

Savannah River Nuclear Solutions has tasked its H Canyon facility to prepare for disposition of used Oak Ridge National Laboratory High Flux Isotope Reactor (HFIR) cores. HFIR cores consist of an inner and outer assembly of highly enriched uranium fuel plates. The two elements are annular, nest inside each other, and the fuel is a curved plate held between two collars. The H-Canyon facility has a dissolver insert specifically designed for HFIR cores and has performed this type of campaign before between 1976 and 1988. At H-Canyon, a dissolver is a large stainless steel pot loaded with a nitric acid solution into which uranium-alloy fuel is dissolved. The dissolver uses a device called an insert to feed the fuels to the acid solution in a controlled manner. The mission will be to dissolve a number of HFIR cores, purify the uranium, and down blend it to low enriched uranium suitable for commercial power reactors. HFIR has a sister core. A French high flux research reactor, called Reactor A Haut Flux (RHF), has nearly the same geometry as the outer element of HFIR. The annulus is only slightly smaller and the RHF active fuel height is {approx}97 cm while the HFIR active fuel height is only {approx}51 cm. SRNS is currently storing RHF cores (repatriated through circa 2003) awaiting a path for disposition. There is now an opportunity. RHF cores fit in the HFIR dissolver insert. Dispositioning them concurrent with HIFR avoids a future facility evolution of just to change dissolver inserts again. This work is the result of an initiative to propose appending the RHF cores to the anticipated HFIR campaign. Geometry and chemistry differences are evaluated and criticality safety assessed. The RHF cores were semi-explicitly modeled in various stages of dissolution. Normal and credible abnormal conditions were assessed. RHF was shown to be bounded by the dissolution of a complete HFIR core in both neutron multiplication and dissolver chemistry. Computational modeling was performed using KENOVI in the SCALE 6.1 code package.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improved Heat Transfer and Volume Scaling through Novel Heater Design

In 2014, the University of California, Berkeley, Nuclear Engineering Thermal Hydraulics Laboratory completed construction of the Compact Integral Effects Test (CIET) facility, a scaled thermal hydraulics scaled integral effects test facility designed to model the Mark-1 pebble-bed fluoride-salt-cooled high-temperature reactor (Mk1 PB-FHR or simply Mk1). CIET uses an organic simulant fluid, Dowtherm A, to match the Prandtl, Reynolds, Froude, and Grashof numbers of important fluoride salt candidates for molten salt reactors, such as flibe. The FHR reactor core is simulated using a resistively heated tube, which heats the oil flowing through the annulus between the heated tube and a non-heated inner tube. However, the volume fraction of the coolant in the CIET heater was dramatically lower than the volume fraction of the primary coolant in the Mk1 PB-FHR design (3% in CIET vs. 17% in Mk1) because the CIET heater was initially scaled to match an earlier FHR design. Also, the maximum core heater power in CIET is limited by the melting point of Teflon components in CIET, approximately 330 deg. C. For conservatism, the CIET heater power is limited to keep the maximum surface temperature of the heater below 250 deg. C. At the nominal mass flow rate of 0.18 kg/s, this power was about 5 kW. A higher heat transfer coefficient from the heater wall to the oil was needed to increase the effective power delivered to the oil. In order to alleviate these two limitations, a new heater insert was designed and constructed for CIET. This new heater insert uses a twisted tape to augment heat transfer. The twisted tape is supported inside a perforated inner tube that has the same diameter as the original inner tube of the heater, in order to make it compatible with CIET's original heater design. The heat transfer and pressure drop properties of the new heater insert designs were tested in CIET and compared to the previous design in terms of pressure drop and convective heat transfer coefficient. The new heater inserts are intended to increase the range of power levels and mass flow rates that can be tested in CIET in order to augment understanding of FHR thermal hydraulic phenomena. Also, obtaining different data points for CIET response dynamics under different heater coolant residence times will be valuable in evaluating the Mk1 design.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

System and method for enclosing piston cooling gallery

A system includes a piston assembly. The piston assembly includes a crown portion having a crown, an outer wall coupled to the crown, a first inner wall disposed inside of the outer wall, a first fluid chamber disposed radially between the outer wall and the first inner wall, and an angled wall insert. An opening extends into the first fluid chamber in an axially inward direction. The outer wall, the first inner wall, the first fluid chamber, the opening, and the angled wall insert extend circumferentially about a central axis of the piston assembly. The angled wall insert is disposed in the opening, and the first fluid chamber is disposed axially between the crown and the angled wall insert.

Zimmerman, Daniel David↗

Stable zymomonas mobilis xylose and arabinose fermenting strains

The present invention briefly includes a transposon for stable insertion of foreign genes into a bacterial genome, comprising at least one operon having structural genes encoding enzymes selected from the group consisting of xylAxylB, araBAD and tal/tkt, and at least one promoter for expression of the structural genes in the bacterium, a pair of inverted insertion sequences, the operons contained inside the insertion sequences, and a transposase gene located outside of the insertion sequences. A plasmid shuttle vector for transformation of foreign genes into a bacterial genome, comprising at least one operon having structural genes encoding enzymes selected from the group consisting of xylAxylB, araBAD and tal/tkt, at least one promoter for expression of the structural genes in the bacterium, and at least two DNA fragments having homology with a gene in the bacterial genome to be transformed, is also provided.The transposon and shuttle vectors are useful in constructing significantly different Zymomonas mobilis strains, according to the present invention, which are useful in the conversion of the cellulose derived pentose sugars into fuels and chemicals, using traditional fermentation technology, because they are stable for expression in a non-selection medium.

60 APPLIED LIFE SCIENCES↗

Armored garment for protecting

A lightweight, armored protective garment for protecting an arm or leg from blast superheated gases, blast overpressure shock, shrapnel, and spall from a explosive device, such as a Rocket Propelled Grenade (RPG) or a roadside Improvised Explosive Device (IED). The garment has a ballistic sleeve made of a ballistic fabric, such as an aramid fiber (e.g., KEVLAR.RTM.) cloth, that prevents thermal burns from the blast superheated gases, while providing some protection from fragments. Additionally, the garment has two or more rigid armor inserts that cover the upper and lower arm and protect against high-velocity projectiles, shrapnel and spall. The rigid inserts can be made of multiple plies of a carbon/epoxy composite laminate. The combination of 6 layers of KEVLAR.RTM. fabric and 28 plies of carbon/epoxy laminate inserts (with the inserts being sandwiched in-between the KEVLAR.RTM. layers), can meet the level IIIA fragmentation minimum V.sub.50 requirements for the US Interceptor Outer Tactical Vest.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Lie group analysis of the point-reactor neutron kinetics equations for various reactivity models

This work applies Lie Group Theory to the nonlinear point-reactor neutron kinetics equations for several reactivity feedback and reactivity insertion models. The goal of this work is to connect known analytical solutions to their corresponding Lie groups as well as to obtain new analytical solutions and the circumstances from which they arise. The reactivity models we consider are the Nordheim-Fuchs Model, an arbitrary-order polynomial reactivity insertion model, and the Fuchs Ramp-Insertion Model. In all three models, we generalize the analysis when possible and obtain analytical solutions in every case. For the first two models, we succeed in finding the Lie groups corresponding to classical solutions and find additional solutions that were otherwise unknown. Finally, for the final model, we obtain a reduced-order nonlinear kinetics equation which is not analytically solvable, but by applying a second-order truncation, we find a novel closed-form solution and demonstrate its validity with a numerical example.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

Sequencing and functional validation of the JGI Brachypodium distachyon T-DNA collection

Due to a large and growing collection of genomic and experimental resources, Brachypodium distachyon has emerged as a powerful experimental model for the grasses. To add to these resources we sequenced 21 165 T-DNA lines, 15 569 of which were produced in this study. This increased the number of unique insertion sites in the T-DNA collection by 21 078, bringing the overall total to 26 112. Thirty-seven per cent (9754) of these insertion sites are within genes (including untranslated regions and introns) and 28% (7217) are within 500 bp of a gene. Approximately 31% of the genes in the v.2.1 annotation have been tagged in this population. To demonstrate the utility of this collection, we phenotypically characterized six T-DNA lines with insertions in genes previously shown in other systems to be involved in cellulose biosynthesis, hemicellulose biosynthesis, secondary cell wall development, DNA damage repair, wax biosynthesis and chloroplast synthesis. In all cases, the phenotypes observed supported previous studies, demonstrating the utility of this collection for plant functional genomics. The Brachypodium T-DNA collection can be accessed at http://jgi.doe.gov/our-science/science-programs/plant-genomics/brachypodium/brachypodium-t-dna-collection/.

59 BASIC BIOLOGICAL SCIENCES↗

Development of refined MCNPX-PARET multi-channel model for transient analysis in research reactors

Reactivity insertion transients are often analyzed (RELAP, PARET) using a two-channel model, representing the hot assembly with specified power distribution and an average assembly representing the remainder of the core. For the analysis of protected by the reactor safety system transients and zero reactivity feedback coefficients this approximation proves to give adequate results. However, a more refined multi-channel model representing the various assemblies, coupled through the reactivity feedback effects to the whole reactor core is needed for the analysis of unprotected transients with excluded over power and period trips. In the present paper a detailed multi-channel PARET model has been developed which describes the reactor core in different clusters representing typical BR2 fuel assemblies. The distribution of power and reactivity feedback in each cluster of the reactor core is obtained from a best-estimate MCNPX calculation using the whole core geometry model of the BR2 reactor. The sensitivity of the reactor response to power, temperature and energy distributions is studied for protected and unprotected reactivity insertion transients, with zero and non-zero reactivity feedback coefficients. The detailed multi-channel model is compared vs. simplified fewer-channel models. The sensitivities of transient characteristics derived from the different models are tested on a few reactivity insertion transients with reactivity feedback from coolant temperature and density change. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Atomistic Conversion Reaction Mechanism of WO 3 in Secondary Ion Batteries of Li, Na, and Ca

Abstract Intercalation and conversion are two fundamental chemical processes for battery materials in response to ion insertion. The interplay between these two chemical processes has never been directly seen and understood at atomic scale. Here, using in situ HRTEM, we captured the atomistic conversion reaction processes during Li, Na, Ca insertion into a WO 3 single crystal model electrode. An intercalation step prior to conversion is explicitly revealed at atomic scale for the first time for Li, Na, Ca. Nanoscale diffraction and ab initio molecular dynamic simulations revealed that after intercalation, the inserted ion–oxygen bond formation destabilizes the transition‐metal framework which gradually shrinks, distorts and finally collapses to an amorphous W and M x O (M=Li, Na, Ca) composite structure. This study provides a full atomistic picture of the transition from intercalation to conversion, which is of essential importance for both secondary ion batteries and electrochromic devices.

He, Yang↗

Functionalization of Carbon Monoxide and tert ‐Butyl Nitrile by Intramolecular Proton Transfer in a Bis(Phosphido) Thorium Complex

Abstract We report intramolecular proton transfer reactions to functionalize carbon monoxide and tert ‐butyl nitrile from a bis(phosphido) thorium complex. The reaction of (C 5 Me 5 ) 2 Th[PH(Mes)] 2 , Mes=2,4,6‐Me 3 C 6 H 2 , with 1 atm of CO yields (C 5 Me 5 ) 2 Th( κ 2 ‐(O,O)‐OCH 2 PMes‐C(O)PMes), in which one CO molecule is inserted into each thorium–phosphorus bond. Concomitant transfer of two protons, formerly coordinated to phosphorus, are now bound to one of the carbon atoms from one of the inserted CO molecules. DFT calculations were employed to determine the lowest energy pathway. With tert ‐butyl nitrile, t BuCN, only one nitrile inserts into a thorium–phosphorus bond, but the proton is transferred to nitrogen with one phosphido remaining unperturbed affording (C 5 Me 5 ) 2 Th[PH(Mes)][ κ 2 ‐(P,N)‐N(H)C(CMe 3 )P(Mes)]. Surprisingly, reaction of this compound with KN(SiMe 3 ) 2 removes the proton bound to nitrogen, not phosphorus.

Vilanova, Sean P.↗