Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “injection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2019

Flow regimes and storage efficiency of CO 2 injected into depleted shale reservoirs

Depleted shale reservoirs are potentially attractive targets to store carbon dioxide (CO 2 ) as free and adsorbed phases. The time-dependent efficiency factors that depict dynamic storage performance in shale are estimated as a function of key reservoir parameters, shapes of stimulated reservoir volume, and injection scenarios. Efficiency of CO 2 storage and flow regimes are determined dynamically as CO 2 is injected in a depleted shale formation for a time period of 60 years. The most effective reservoir utilization for carbon storage was achieved during the transition from predominant flow in the stimulated reservoir volume to flow into unfractured zones. That transition occurs within first 15–30 years of injection depending on cases considered. The importance of adsorption as a mechanism of storage is determined based on sensitivity, which indicates that the amount of CO 2 stored by adsorption would be on average ~26% of the CO 2 stored as a free phase.

03 NATURAL GAS↗
DOE OSTI2013

Sensitivity of injection costs to input petrophysical parameters in numerical geologic carbon sequestration models

Numerical simulations are widely used in feasibility studies for geologic carbon sequestration. Accurate estimates of petrophysical parameters are needed as inputs for these simulations. However, relatively few experimental values are available for CO2-brine systems. Hence, a sensitivity analysis was performed using the STOMP numerical code for supercritical CO2 injected into a model confined deep saline aquifer. The intrinsic permeability, porosity, pore compressibility, and capillary pressure-saturation/relative permeability parameters (residual liquid saturation, residual gas saturation, and van Genuchten alpha and m values) were varied independently. Their influence on CO2 injection rates and costs were determined and the parameters were ranked based on normalized coefficients of variation. The simulations resulted in differences of up to tens of millions of dollars over the life of the project (i.e., the time taken to inject 10.8 million metric tons of CO2). The two most influential parameters were the intrinsic permeability and the van Genuchten m value. Two other parameters, the residual gas saturation and the residual liquid saturation, ranked above the porosity. These results highlight the need for accurate estimates of capillary pressure-saturation/relative permeability parameters for geologic carbon sequestration simulations in addition to measurements of porosity and intrinsic permeability.

Cost estimate↗
DOE OSTI2013

Geomechanical effects on CO 2 leakage through fault zones during large-scale underground injection

The importance of geomechanics—including the potential for faults to reactivate during large-scale geologic carbon sequestration operations—has recently become more widely recognized. However, notwithstanding the potential for triggering notable (felt) seismic events, the potential for buoyancy-driven CO 2 to reach potable groundwater and the ground surface is actually more important from public safety and storage-efficiency perspectives. In this context, this paper extends the previous studies on the geomechanical modeling of fault responses during underground carbon dioxide injection, focusing on the short-term integrity of the sealing caprock, and hence on the potential for leakage of either brine or CO 2 to reach the shallow groundwater aquifers during active injection. We consider stress/strain-dependent permeability and study the leakage through the fault zone as its permeability changes during a reactivation, also causing seismicity. We analyze several scenarios related to the volume of CO 2 injected (and hence as a function of the overpressure), involving both minor and major faults, and analyze the profile risks of leakage for different stress/strain-permeability coupling functions. We conclude that whereas it is very difficult to predict how much fault permeability could change upon reactivation, this process can have a significant impact on the leakage rate. Moreover, our analysis shows that induced seismicity associated with fault reactivation may not necessarily open up a new flow path for leakage. Results show a poor correlation between magnitude and amount of fluid leakage, meaning that a single event is generally not enough to substantially change the permeability along the entire fault length. Finally, and consequently, even if some changes in permeability occur, this does not mean that the CO 2 will migrate up along the entire fault, breaking through the caprock to enter the overlying aquifer.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Hydraulic fracturing to enhance injectivity and storage capacity of CO 2 storage reservoirs: Benefits and risks

Several potential CO 2 storage reservoirs have been found to have insufficient porosity and permeability to support cost effective commercial-scale injection. As a result, the use of hydraulic fracturing to enhance injectivity and storage capacity of CO 2 storage reservoirs was explored. Previous modeling studies indicate that fracturing can increase storage capacity by modest to significant amounts (10%–35%), depending on model assumptions. Simulations completed as part of this study confirm that for a range of horizontal well lengths, number of fractures, fracture geometries, and fracture properties, injectivity is improved and capacity increases by 13%–71% over the base case unfractured vertical well. Intuitively, increasing the well length and number of fractures had a corresponding impact on increased capacity. Here, fracture area (i.e., the fracture height multiplied by its width) was an important parameter for increasing capacity but the specific geometry (e.g., the ratio of height-to-width) was unimportant. The most important aspect that affected capacity was the ability of a fracture to connect high permeability horizontal zones in the reservoir. This would allow a single well to access both layers, thereby maximizing total storage capacity of the reservoir while likely leading to an overall increase of the CO 2 footprint, which is an important consideration for Class VI UIC permitting. The results of this work demonstrate that hydraulic fracturing is an attractive option to consider when faced with an underperforming geologic carbon storage site that is at risk of causing a project to fail.

03 NATURAL GAS↗
DOE OSTI2021

A screening model for predicting injection well pressure buildup and plume extent in CO 2 geologic storage projects

We present a new screening model for predicting injection well pressure buildup and CO 2 plume migration for CO 2 geologic sequestration projects. The model requires only limited information and is quite accurate when compared to detailed simulation results. Such models can assist project developers during the early days of project planning (e.g., for 45Q related projects), and also help regulators perform simple checks against detailed numerical models. The screening model consists of two correlations: one for injectivity index in terms of the slope of the CO 2 fractional flow curve, and the second for total storage efficiency within the footprint of plume as a function of gravity number and slope of the CO 2 fractional flow curve. Using these two correlations, as well as a knowledge of some basic reservoir characteristics and estimates of fluid properties from standard correlations, the injection-well pressure buildup and CO 2 plume extent in the formation can be readily estimated. Finally, the new correlations show a good match with the results of the underlying simulations, and also provide good agreement with independent calculations for two example problems.

42 ENGINEERING↗
DOE OSTI2024

CFD unified approach under Eulerian–Lagrangian framework for methanol and gasoline direct injection sprays in evaporative and flash boiling conditions

Innovative synthetic fuels for advanced propulsion systems, such as methanol and ammonia, and synthetic blended fuels (E00, E10, and E30), known for their high volatility, are often injected directly into combustion chambers. It follows that Eulerian–Lagrangian spray models need to accurately capture the spray collapse as a consequence of flash boiling onset and be capable of proficiently handling the preferential evaporation of multi-component fuels in evaporative scenarios. So, we performed the assessment of an Eulerian–Lagrangian CFD code for simulating methanol and E00 gasoline blend sprays in both early and late injection conditions involving flash boiling conditions and preferential evaporation. The adoption of an effervescent breakup model and of a non-equilibrium phase transition model for the discrete phase allows the adoption of a setup that is almost completely free from specific constant tuning, especially for what concerns the breakup model. We validated the simulations using experimental PLV maps of methanol and E00 sprays issued from the ECN Spray M injector. The results highlight a significantly different morphology of the methanol spray compared to the E00 one under late injection conditions. Under stratified combustion, low-volatile fuels are likely to be ignited first, and the flame propagates toward the high-volatile fuels. In conclusion, the spray collapse was also correctly reproduced, inducing the presence of a low-pressure zone and modifying the spray morphology.

E00↗
DOE OSTI2023

Core-scale numerical simulation and comparison of breakdown of shale and resulting fractures using sc-CO 2 and water as injectants

Supercritical carbon dioxide (sc-CO 2 ) is an alternative to water for stimulation of low permeability systems such as shale gas and geothermal resources. Previously core-scale experimental studies have compared the behavior of CO 2 to water injection for sample breakdown. Due to differences in experimental setup and core sample preparation, inconsistent or even apparently contradictory conclusions have resulted. To reconcile this contradiction, a phase-field numerical model is applied to understand hydraulic fracturing experiments using Green River shale found in the literature. The finite element numerical model incorporates a rate-dependent phase-field fracture model developed separately to describe fracture initiation and growth. We investigate the impact of various material and fluid properties on the resulting fractures. Most importantly, we study the effect of fluid properties and boundary conditions on the breakdown pressure, including the direction of the resulting fracture plane. Model results predict that (1) sc-CO 2 injection in the laboratory may result in greater breakdown pressure than that of water under no-flow boundary conditions because lower viscosity sc-CO 2 may result in pressure build up at the core boundary that opposes fracture initiation and (2) lower viscosity sc-CO 2 also produces fast-propagating fractures that are less influenced by the bedding plane on their resulting fracture topology. Here our model offers a straightforward explanation and reconciliation of existing experimental observations, as well as a means to extrapolate to new conditions. Exploration of field-scale conditions suggests less pronounced or no elevation in breakdown pressure when sc-CO 2 is injected because the pressure build up effect at the system boundary is significantly less or absent at field length scales.

42 ENGINEERING↗
DOE OSTI2019

Combined effect of injected interstitials and He implantation, and cavities inside dislocation loops in high purity Fe-Cr alloys

High purity Fe-Cr alloys with Cr content ranging from 3 to 14 wt% were irradiated by self-ions at 500 °C in dual-beam mode up to 157 displacements per atom (dpa), 17 appm He/dpa. Transmission electron microscopy (TEM) on focused ion beam foils revealed the depth distribution of irradiation induced cavities and dislocation loops. A detailed quantitative analysis of cavity microstructure was performed on Fe14%Cr, while Fe(3, 5, 10, 12)%Cr were analyzed qualitatively. A homogeneous distribution of small cavities were observed up to the damage peak. From surface to the damage peak, cavity number density increased almost linearly. The cavity microstructure changed drastically at and after the damage peak, where the size increased and number density decreased. Most notably, the microstructure consisted of a striking mixture of heterogeneously nucleated cavities inside dislocation loops and freely nucleated cavities in the matrix. Further, the depth-dependent void swelling increased continuously along the damage depth. This contrasts with most ion irradiation results where suppression of void swelling occurs adjacent to the damage peak due the injected interstitial effect. We hypothesize a plausible mechanism of the observed swelling variation based on a combined effect of the injected interstitials and helium implantation near the damage peak by comparing the results with those in pure iron irradiated under same conditions. This synergistic effect may develop cavity microstructures which do not necessarily reflect microstructures expected due to injected interstitial effect and can be easily wrongly interpreted. The depth dependent dislocation loop microstructure was studied qualitatively in Fe14%Cr sample. Up to the damage peak, a complex dense network of dislocations formed due to the interaction/impingement of the dislocation loops. Individually resolvable loops were only observed after the damage peak, where their association with cavities was noted. Furthermore helium also induced heterogeneous cavity nucleation on dislocations constituting a grain boundary and on pre-existing dislocation lines.

36 MATERIALS SCIENCE↗
DOE OSTI2015

The effect of aging treatment on the fracture toughness and impact strength of injection molded Ni-625 superalloy parts

In this study, the effect of aging heat treatment on fracture toughness and impact strength of Ni-625 superalloy fabricated by using powder injection molding (PIM) method was examined. After a feedstock was prepared by mixing the prealloyed Ni-625 superalloy powder, which was fabricated by gas atomisation, with a polymeric binder system and then it was granulated, it was shaped through the use of injection. The molded specimens were sintered at 1300 °C for 3 h after a two-stage debinding process. Once the sintered specimens were treated in the solution at 1150 °C for 2 h, they were quenched. Aging treatment was performed by keeping specimens at 745 °C for 22 h. Fracture toughness and impact tests were performed on sintered and aged specimens. Microstructure examinations were performed by using optical microscope, scanning electron microscope, and transmission electron microscope. The results revealed that aging heat treatment led to the formation of some carbides and intermetallic phases in the microstructure. While the hardness of the aged specimens increased due to these phases, their fracture toughness and impact strength values decreased. - Highlights: • Ni-625 superalloy components were produced by means of powder injection molding. • The produced components were subjected to aging treatment. • Aging process provided approximately 50% increase in the hardness of components. • Intermetallic precipitates, carbides and TCP phases occurred within the aged parts. • Fracture toughness and impact strength values decreased due to the hard phases.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Real-time wall conditioning by controlled injection of boron and boron nitride powder in full tungsten wall ASDEX Upgrade

In ASDEX Upgrade with full-tungsten wall, boronization is an important tool to control tungsten sources and allow reliable operation at low collisionality. The duration of the beneficial effects is limited by the erosion of the boron layer, in particular on the tungsten ion-cyclotron antenna limiters. We report results from experiments exploring injection boron-rich powders in tokamak plasmas as a way to replenish boron coating and extend the lifetime of boronization effects. Pure boron and boron nitride powders were introduced gravitationally in plasma discharges at rates up to 60 mg/s for durations up to 3 s. Boron injection with cumulative amounts >100 mg appeared to improve wall conditions similarly to boronization, with indications of reduced influx of oxygen and tungsten from the antenna limiter. Moreover, cumulative injection of 340 mg of B appeared sufficient to enable successful execution of low collisionality scenarios critically relying on freshly boronized walls.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Wall conditioning and ELM mitigation with boron nitride powder injection in KSTAR

Results from KSTAR powder injection experiments, in which tens of milligrams of boron nitride (BN) were dropped into low-power H-mode plasmas, show an improvement in wall conditions in subsequent discharges and, in some cases, a reduction or elimination of edge-localized modes (ELMs). Injected powder is distributed by the plasma flow and is deposited on the wall and, over the course of several discharges, was observed to gradually reduce recycling by 33%, and decrease both the ELM amplitude and frequency. This is the first demonstration of the use of BN for ELM mitigation. In all of these experiments, an Impurity Powder Dropper (IPD) was used to introduce precise, controllable amounts of the materials into ELMy H-mode KSTAR discharges. The plasma duration was between 10 s and 15 s, I p = 500 kA, B T = 1 . 8 T, P NBI = 1 . 6 MW, and P ECH = 0 . 6 MW. Plasma densities were between 2 and 3 × 1 0 19 m -3 . In all cases, the pre-fill and startup gas-fueling was kept constant, suggesting that the decrease in baseline D α emission is in fact due to a reduction in recycling. The results presented herein highlight the viability of powder injection for intra-shot and between-shot wall conditioning

36 MATERIALS SCIENCE↗
DOE OSTI2022

Active wall conditioning through boron powder injection compatible $\mathrm{ELM}$ control in $\mathrm{EAST}$

Real-time wall conditioning and edge-localized mode (ELM) suppression through real-time boron powder injection into high-confinement mode discharges of the Experimental Advanced Superconducting Tokamak (EAST) have been investigated. The boron powder injection effectively conditioned the plasma-facing components, as shown by the reductions in low-Z and high-Z impurities and the global recycling level in the whole inner vessel, and suppressed the strong magnetohydrodynamic (MHD) activity in the plasma core. The improved wall conditions also resulted in an earlier transition from L- to H-mode. Boron powder injection also effectively suppressed ELM in the lower single null configuration with BT in the favorable direction while leaving the plasma density and stored energy largely unaffected.

36 MATERIALS SCIENCE↗
DOE OSTI2017

Combined Falling Drop/Open Port Sampling Interface System for Automated Flow Injection Mass Spectrometry

The aim of this work was to demonstrate and to evaluate the analytical performance of a combined falling drop/open port sampling interface (OPSI) system as a simple noncontact, no-carryover, automated system for flow injection analysis with mass spectrometry. The falling sample drops were introduced into the OPSI using a widely available autosampler platform utilizing low cost disposable pipet tips and conventional disposable microtiter well plates. The volume of the drops that fell onto the OPSI was in the 7–15 μL range with an injected sample volume of several hundred nanoliters. Sample drop height, positioning of the internal capillary on the sampling end of the probe, and carrier solvent flow rate were optimized for maximum signal. Sample throughput, signal reproducibility, matrix effects, and quantitative analysis capability of the system were established using the drug molecule propranolol and its isotope labeled internal standard in water, unprocessed river water and two commercially available buffer matrices. A sample-to-sample throughput of ~45 s with a ~4.5 s base-to-base flow injection peak profile was obtained in these experiments. In addition, quantitation with minimally processed rat plasma samples was demonstrated with three different statin drugs (atorvastatin, rosuvastatin, and fluvastatin). Direct characterization capability of unprocessed samples was demonstrated by the analysis of neat vegetable oils. Employing the autosampler system for spatially resolved liquid extraction surface sampling exemplified by the analysis of propranolol and its hydroxypropranolol glucuronide phase II metabolites from a rat thin tissue section was also illustrated.

47 OTHER INSTRUMENTATION↗
DOE OSTI2026

Silyl Hot-Injection Versus Thiocyanate Heat-Up Synthesis of Chalcohalides: Pushing the Size and Composition Envelope

Chalcohalide semiconductors are rapidly gaining traction as stable, biocompatible materials for energy conversion applications. While the solid-state synthesis of bulk chalcohalides is relatively well-developed, the colloidal chemistry of these materials is still in its early stages. Colloidal semiconductors are often advantageous in device fabrication due to the cost effectiveness of solution processing. Thus, we aim to increase the utility of chalcohalides in device fabrication by establishing solution phase chemistry of promising compositions. We show that silyl hot-injection is a versatile and effective method of making colloidal PnChI (Pn = Sb, Bi; Ch = S, Se) and Sn 2 PnS 2 I 3 (Pn = Sb, Bi) chalcohalides of tunable sizes and compositions. Furthermore, we demonstrate the preparation of mixed-pnictide chalcohalides through direct hot-injection and/or postsynthetic cation exchange, the latter being one of the few reported instances in chalcohalides. Additionally, we use the thiocyanate heat-up approach in combination with density functional theory to study halide mixing in quaternary tin chalcohalides. By pushing the limits of each synthetic technique, we have designed more soluble chalcohalides with tunable compositions while also gaining a better understanding of the efficacy of each procedure in respect to thin film and subsequent device fabrication. In addition to size and composition tuning, silyl hot-injection can help facilitate the future development and wide-scale application of chalcohalide-based devices by expanding the selection of solution-processable chalcohalides.

halogens↗
DOE OSTI2018

Novel Technological Approach To Enhance Methane Recovery from Class 2 Hydrate Deposits by Employing CO 2 Injection

Class 2 hydrate accumulations are characterized by the presence of an aquifer underneath hydrate bearing sediment. Gas extraction from of these hydrate deposits is accompanied by release of large volumes of water that decreases gas production rates, imposes additional load on the lifting system and, as a result, degrades economical attractiveness of possible exploitation sites. Here, we study the enhanced methane production from Class 2 hydrate accumulations using the CO 2 -assisted technique in which the aquifer serves as a target zone for CO 2 injection. The heat release associated with the CO 2 hydrate formation and reduction of the aquifer’s permeability benefit the subsequent decomposition of the overlying methane hydrate. The new production technique includes three stages utilizing one vertical well, which serves as an injector during the first stage and as a producer in the third stage. First, the CO 2 is injected into the underlying aquifer, then the well is shut down and injected CO 2 is converted into hydrate during the second stage. In the third stage, decomposition of CH 4 hydrate is induced by the depressurization method to estimate gas production potential over 15 years. Lastly, the results reveal that methane production is increased together with simultaneous reduction of concomitant water production compared to production from the Class 2 reservoir using only conventional depressurization.

03 NATURAL GAS↗
DOE OSTI2018

Pathways Following Electron Injection: Medium Effects and Cross-Surface Electron Transfer in a Ruthenium-Based, Chromophore–Catalyst Assembly on TiO 2

Interfacial dynamics following photoexcitation of the water oxidation assembly [((PO 3 H 2 ) 2 bpy) 2 Ru II (bpy-bimpy)Ru II (tpy)(OH 2 )] 4+ , -[Ru a II –Ru b II –OH 2 ] 4+ , on nanocrystalline TiO 2 electrodes, starting from either -[Ru a II –Ru b II –OH 2 ] 4+ or -[Ru a II –Ru b III –OH 2 ] 5+ , have been investigated. Transient absorption measurements for TiO 2 –[Ru a II –Ru b II –OH 2 ] 4+ in 0.1 M HPF 6 or neat trifluoroethanol reveal that electron injection occurs with high efficiency but that hole transfer to the catalyst, which occurs on the electrochemical time scale, is inhibited by local environmental effects. Back electron transfer occurs to the oxidized chromophore on the microsecond time scale. Photoexcitation of the once-oxidized assembly, TiO 2 –[Ru a II –Ru b III –OH 2 ] 5+ , in a variety of media, generates -[Ru a III –Ru b III –OH 2 ] 6+ . The injected electron randomly migrates through the surface oxide structure reducing an unreacted -[Ru a II –Ru b III –OH 2 ] 5+ assembly to -[Ru a II –Ru b II –OH 2 ] 4+ . In a parallel reaction, -[Ru a III –Ru b III –OH 2 ] 6+ formed by electron injection undergoes proton loss giving -[Ru a II –Ru b IV $=$O] 4+ with possible conversion to -[Ru a II –Ru b II –OH 2 ] 4+ by an electrolyte-mediated reaction. In the following slow step, re-equilibration on the surface occurs either by reaction with added Fe III/II or by cross-surface electron transfer between spatially separated -[Ru a II –Ru b IV $=$O] 4+ and -[Ru a II –Ru b II –OH 2 ] 4+ assemblies to give -[Ru a II –Ru b III –OH 2 ] 5+ with a half-time of t 1/2 ~ 68 μs. Finally, these results and analyses show that the transient surface behavior of the assembly and cross-surface reactions play important roles in producing and storing redox equivalents on the surface that are used for water oxidation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2019

Modeling Electron Injection at Semiconductor–Molecule Interfaces using First-Principles Dynamics Simulation: Effects of Nonadiabatic Coupling, Self-energy, and Surface Models

Excited electron transfer across semiconductor–molecule heterogeneous interfaces is central to various future electronic and optoelectronic devices. At the same time, first-principles modeling of such dynamical processes remains as a great challenge in theoretical chemistry and condensed matter physics for developing better understanding at the molecular scale. Excited electron transfer from a molecule to semiconductor surface is a particularly difficult case to model accurately, because the initial state of such an electron injection process often lies deep within the dense manifold of the conduction band states in the semiconductor. Nonadiabatic couplings and energy level alignments at such interfaces as well as the finite size error of the surface model all play important roles in numerical modeling of electron injection via first-principles theory. Here, using representative interfaces between a well-defined hydrogen-terminated Si(111) surface and series of covalently adsorbed conjugated molecules, we investigate the extent to which these theoretical and numerical considerations influence the description of electron injection at the semiconductor–molecule interface.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2015

Crucial role of nuclear dynamics for electron injection in a dye–semiconductor complex

In this study, we investigate the electron injection from a terrylene-based chromophore to the TiO 2 semiconductor bridged by a recently proposed phenyl-amide-phenyl molecular rectifier. The mechanism of electron transfer is studied by means of quantum dynamics simulations using an extended Hückel Hamiltonian. It is found that the inclusion of the nuclear motion is necessary to observe the photoinduced electron transfer. In particular, the fluctuations of the dihedral angle between the terrylene and the phenyl ring modulate the localization and thus the electronic coupling between the donor and acceptor states involved in the injection process. The electron propagation shows characteristic oscillatory features that correlate with interatomic distance fluctuations in the bridge, which are associated with the vibrational modes driving the process. The understanding of such effects is important for the design of functional dyes with optimal injection and rectification properties.

36 MATERIALS SCIENCE↗