SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The 4-point bending strength of 4 grades of hot-pressed SiC was determined at different temperatures. With a transgranular mode of fracture the values for bending strength are retained up to high temperatures. For intergranular fracture the decrease of strength is governed by subcritical crack growth. The intergranular fracture is caused by a high content of silicate glassy phase at the grain boundaries of hot-pressed SiC.
The introduction of ceramics to those parts suffering high thermal loading was successfully demonstrated, and there is no question that the 100 kw (134 hp) naturally aspirated engine of the future will be developed to produce up to 300 kw (402 hp) by the application of turbocharging or its equivalent. However, at the 60 - 80 kw (80 - 107 hp) size needed for the economic automotive engine, scaling down the 300 kw (402 hp) is beset by the laws of scale. The conventional four stroke diesel was not shown to be successful at the small high speed engine size. The opposed piston two stroke engine does not suffer the same laws of scale and engines in the low power range have already been marketed successfully. The half liter/cylinder Armstrong Whitworth Swing Beam Engine is the latest to be designed with the automotive market in mind. Its low noise structure and balanced linkage system coupled with advantages for easy start and potential use of low grade fuels, derived from its variable compression ratio and slow piston motion, qualifies it for the application.
A network of channels was chemically milled into one surface of a pair of matched plates having bond planes which were neither planar or profiled to match the contour of the trailing edge of a supercritical airfoil for testing in cryogenic wind tunnels. Vacuum brazing bonded the plates together to create a network of pressure passages without blockages or cross leaks. The greatest success was achieved with the smaller samples and planar bonding surfaces. In larger samples, problems were encountered due to warpage created by the relief of residual stresses. Successful bonds were formed by brazing A286, Nitronic 40 and 300 series stainless steels at 1065 C using AMS 4777B brazing alloy, but excessive grain growth occurred in samples of 200 grade 18 nickel maraging steels. Good bonds were obtained with maraging steel using a 47 percent Nickel-47 percent Palladium-6 percent Silicon alloy and brazing at 927 C. Electro-Discharge-Machining was an effective method of cutting profiled bond planes and airfoil contours. Orifices of good definition were obtained when the EDM wire cut passed through predrilled holes. Possible configurations for joints between small segments and the larger main wing were also studied.
The photograph of a comet or asteroid against background stars contains information in analog form regarding the relative positions of comet and star images. Measuring is the procedure for covnerting this information to digital form for computation of the object's accurate equatorial coordinates at the time of observation. The use of one- and two-coordinate measuring engines to measure the positions of images which may be elongated, comatic, or both, as well as round images is discussed along with the training of novice measurers to cope with such images. The grading of plates for potential accuracy of positions, preparation of plates for measuring, the accuracy of measurement, effects of telescope focal length and reduction technique upon the accuracy of positions, and the procedures and checks which may prevent erroneous positions also are discussed.
The broad objective of this research program is to determine the role which gravity plays in the growth and development of mammalian animals. Current studies are focused on the effects of graded hypergravitatinal field intensities on mice, rats and other small sized laboratory animals using the chronic centrifugation technique. They include studies on reproduction and prenatal and postnatel growth and development. Among the important questions addressed are: (1) what stage or stages in animal development are affected by hypergravity and what are the effects? (2) is there a minimum or critical body size for hypergravity to produce a significant effect on growth and development? (3) are there field intensity thresholds for the preceding questions? From analysis of the body masses at birth of rats conceived and allowed to undergo gestation under 2.1G and under normal gravity (1G), it was found that there was no significant difference between the two groups. Futhermore, their growth rates postnatally were the same until they reached a body mass of approximately 50 grams when the 2.1G group showed a significantly slower rate. Results from these studies support the conclusion that prenatal as well as the early postnatal stages of growth and development of the rat are refractory to hyper-G.
Ion plating is an ion assisted or glow discharge deposition technique, where ions or energetic atoms transfer energy, momentum and charge to the substrate and the growing film in a manner which can be controlled to favorably modify surface, subsurface chemistry, and microstructure. The glow discharge energizing effects from the initial nucleation stages to the final film growth are discussed. As a result, adherence, coherence, internal stresses, density and morphology of the coatings are significantly improved, over the conventional (nonion-assisted) techniques which in turn favorably affect the surface initiated failures caused by friction, wear, erosion, corrosion and fatigue. Ion plated films because of their graded coating/substrate interface, fine, uniform, densely packed film structure also induce a surface strengthening effect which improved the mechanical properties such as yield, tensile strength and fatigue life. Since a uniform, continuous film can be obtained at lower nominal film thickness, this effect is of great importance in solid film lubrication and in corrosion protection.
Early silicon solar cells were made of metallurgical-grade silicon with very low efficiency. The single-crystal silicon introduced in the mid-50's increased the efficiency to the 5% to 10% region. Throughout the 1960s the technology of the 2 x 2 cm or 2 x 4 cm space solar cell with 10% efficiency was established. In the early 1970s work related to the violet cell upset the status quo and space solar cells and cells in general became more efficient. The rest of the decade became characterized by establishing a terrestrial photovoltaic technology to support the development of a new industry. Costs per watt became the dominant consideration and frequently the efficiency was compromised. The introduction of materials and other forms of silicon dropped the efficiency and it is now a state of mine that accomplishing 10% efficiency with some alternative combination is regarded as success. Silicon solar cells are capable of delivering efficiences much greater than 10%.
The interaction between seawater and submarine volcanic rock has had important consequences for the chemistry of the ocean during the Phanerozoic. Most extant terranes have been regionally metamorphosed to the amphibolite and granulite facies, so that their precursor lithologies and structures are not readily determinable. However, the 3.5 b.y. old supracrustal rocks of the Barberton Mountain Land, South Africa, have not been subjected to high grade regional metamorphism, and therefore there was reason to hope that a laboratory investigation might reveal the extent to which these rocks had been exposed to subseafloor hydrothermal activity. Hart and de Wit describe bulk geochemical evidence from the entire suite as well as field evidence which support the concept of hydrothermal activity in the Barberton Mountain Land. Mineralogical and textural features which unequivocally mark it as a submarine sequence emplaced in a midocean ridge/fracture zone or back arc/fracture zone environment are briefly discussed.
The lower continental crust, formerly very poorly understood, has recently been investigated by various geological and geophysical techniques that are beginning to yield a generally agreed on though still vague model (Lowman, 1984). As typified by at least some exposed high grade terranes, such as the Scottish Scourian complex, the lower crust in areas not affected by Phanerozoic orogeny or crustal extension appears to consist of gently dipping granulite gneisses of intermediate bulk composition, formed from partly or largely supracrustal precursors. This model, to the degree that it is correct, has important implications for early crustal genesis and the origin of continental crust in general. Most important, it implies that except for areas of major overthrusting (which may of course be considerable) normal superposition relations prevail, and that since even the oldest exposed rocks are underlain by tens of kilometers of sial, true primordial crust may still survive in the lower crustal levels (of. Phinney, 1981).
The Crab pulsar PSR0531+21 was observed in a balloon flight from the Xianghe Balloon Station (China). Data were obtained in the range 20 to 200 keV with a poswish hard X-ray telescope which comprised a 150 sq cm primary crystal of 5 mm thick CsI(T1) which actively shielded the lower 2 pi steradians by a 5 cm thick NaI(T1) crystal. The scintillation pulses originating in CsI and NaI crystals are distinguished by pulse shape discrimination. The telescope has a field of view of approximately 4 deg H psi H pi determined by graded shield and collimator. The effective geometric area of the detector is 116 sq cm. It is noted that when folding a data flow on a long period interference from the data acquisition, transmission and recording system considerably affect the result.
It is pointed out that the ambitious goals envisaged for the next generation of space-borne sensors challenge the state-of-the-art in solid-state imaging technology. Studies are being conducted with the aim to provide focal plane array technology suitable for use in future Multispectral Linear Array (MLA) earth resource instruments. An important new technology for IR-image sensors involves the use of monolithic Schottky barrier infrared charge-coupled device arrays. This technology is suitable for earth sensing applications in which moderate quantum efficiency and intermediate operating temperatures are required. This IR sensor can be fabricated by using standard integrated circuit (IC) processing techniques, and it is possible to employ commercial IC grade silicon. For this reason, it is feasible to construct Schottky barrier area and line arrays with large numbers of elements and high-density designs. A Pd2Si Schottky barrier sensor for multispectral imaging in the 1 to 3.5 micron band is under development.
Ellipsometric measurements of the thickness of the wetting layer of sulfur hexafluoride that forms on a fused-silica surface partially immersed in the liquid are presented. The components of the experiment included a He-Ne laser (0.6328 micron), polarizer, and quarter-wave plate with 45-deg azimuth. An optical-grade fused-silica prism was polished to wavelength/20, and strain-induced birefringence was accounted for. It was found that the layer thickness decreases from 40 to 20 nm with a height increase from 0.7 to 3 mm above the liquid-vapor interface. The thickness is independent of the temperature between 10 and 0.1 K below the critical temperature (319 K). The results are compared in detail to the theory of Dzyaloshinskii et al. (1961), and are noted to coincide closely.
The atomic environment of iron impurities is investigated during the processing cycle of reaction-bonding silicon nitride (RBSN). Several analysis techniques are utilized, including X-ray photoelectron spectroscopy (XPS), extended X-ray absorption fine structure (EXAFS), and electron spin resonance (ESR), to examine iron impurities in the starting silicon powder, in sintered silicon compacts, and in RBSN materials. Results indicate that iron impurities in as-received metallurgical grade silicon powder are incorporated in the silicon bulk as a highly distorted FeSi2 compound. No surface iron or iron-based particulate is observed in the starting material. Upon sintering, the iron environment becomes an ordered FeSi2 structure. In the RBNS material, the FeSi2 structure is again distorted, as observed by both EXAFS and ESR.
The effects of 10-d 6-deg-head-down bed rest (BR1), 14 d of recovery, another 10 d bed rest (BR2), and another 14-d recovery on the cardiovascular response to a graded supine cycle ergometer test (4 min unloaded 60-rpm pedaling followed by 15-W/min increasing work load to volitional fatigue) are investigated experimentally in seven male nonsmokers of mean age 41 yrs, mean weight 80.2 kg, mean height 178 cm, and mean body fat content 22.3 percent. Ergometer tests are performed before BR1, after BR1 and BR2, and 14 d after BR2. The results are presented in tables, and it is found that the significantly decreased maximum-O2-uptake, gas-exchange-aerobic-threshold, and plasma-volume responses and the increased submaximal and maximal heart rates observed (relative to pre-BR1 levels) after BR1 and BR2 return to pre-BR1 values 14 d after BR2. It is inferred that 14 d of mild exercise are adequate for recovery from even repeated exposure to this type of simulated weightlessness.
Sm-Nd and Rb-Sr isotopic data for the Bad Vermilion Lake anorthosite in the Rainy Lake area of the Superior Province of northwesten Ontario show that direct ages of Archean anorthosites can be obtained with these isotopic systems despite the effects of low-grade metamorphism. There is sufficient spread in Sm/Nd between plagioclase megacrysts and coexisting mafic groundmass to allow the determination of reasonably precise internal Sm-Nd isochrons. Initial isotopic ratios of Nd and Sr add to the growing body of data indicating the Superior Province is underlain by depleted mantle.
A very long-life, lightweight and efficient hydride absorption refrigerator system was built to operate at ten Kelvin and below. The system consists of four basic stages of refrigeration. The first stage is accomplished by an active refrigeration system. The second stage is operated by a hydride absorption system, wherein a heated hydride powder drives off high pressure hydrogen through a Joule-Thomson/heat exchanger expansion loop such that the hydrogen is partially liquefied. In the third stage, the vapor pressure over the collected liquid hydrogen is lowered by absorbing the hydrogen vapor onto a different low pressure, worn hydride. With a 1.7 torr partial pressure of hydrogen gas in the hydride, liquid hydrogen is solidified and sublimes at 10 K. Long-life adiabatic demagnetization refrigerators, helium desorption, or helium diaphragm compressors are used to cool to 4 K or below. It is shown that the hydride concepts provide an extremely efficient means of refrigeration to 10 K, and that an entire sorption refrigeration process can be accomplished solely by using low grade heat energy at about 150 C.
Experimentally determined values of true secondary electron emission and relative values of reflected primary electron yield for a range of primary electron beam energies and beam impingement angles are presented for a series of novel textured carbon surfaces on copper substrates. (All copper surfaces used in this study were oxygen-free, high-conductivity grade). The purpose of this investigation is to provide information necessary to develop high-efficiency multistage depressed collectors (MDC's) for microwave amplifier traveling-wave tubes (TWT's) for communications and aircraft applications. To attain the highest TWT signal quality and overall efficiency, the MDC electrode surface must have low secondary electron emission characteristics. While copper is the material most commonly used for MDC electrodes, it exhibits relatively high levels of secondary electron emission unless its surface is treated for emission control. The textured carbon surface on copper substrate described in this report is a particularly promising candidate for the MDC electrode application. Samples of textured carbon surfaces on copper substrates typical of three different levels of treatment are prepared and tested for this study. The materials are tested at primary electron beam energies of 200 to 2000 eV and at direct (0 deg) to near-grazing (85 deg) beam impingement angles. True secondary electron emission and relative reflected primary electron yield characteristics of the textured surfaces are compared with each other and with those of untreated copper. All the textured carbon surfaces on copper substrate tested exhibited sharply lower secondary electron emission characteristics than those of an untreated copper surface.
Corrosion rates of 304L stainless steel coupons in MON-1 oxidizer have been measured as a function of cleaning procedures employed, surface layer positions, propellant impurity levels, and short-term exposure durations (14 to 90 days). Of special interest was propellant contamination by buildup of soluble iron, which may cause flow decay. Surface treatments employed were combinations of cleaning, pickling, and passivation procedures. Propellants used were MIL-SPEC MON-1 and several types of purified NTO (i.e., low water, low chloride) which may, at a later time, be specified as spacecraft grade. Pretest coupon surface analysis by X-ray photoelectron spectroscopy (XPS-ESCA) has revealed important differences, for the different cleaning procedures, in the make-up of the surface layer, both in composition and state of chemical combination of the elements involved. Comparisons will be made of XPS/ESCA data, for different cleaning procedures, for specimens before and after propellant exposure.