Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fuel combustion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Effect of inlet temperature on the performance of a catalytic reactor

A 12-cm-diameter by 15-cm-long catalytic reactor was tested with No. 2 diesel fuel in a combustion test rig at inlet temperatures of 700, 800, 900, and 1000 K. Other test conditions included pressures of 300,000 and 600,000 Pa, reference velocities of 10, 15, and 20 m/s, and adiabatic combustion temperatures in the range from 1100 to 1400 K. The combustion efficiency was calculated from measurements of carbon monoxide and unburned hydrocarbon emissions. Nitrogen oxide emissions and reactor pressure drop were also measured. At a reference velocity of 10 m/s, the CO and unburned hydrocarbons emissions and, therefore, the combustion efficiency were independent of inlet temperature. At an inlet temperature of 1000 K, they were independent of reference velocity. Nitrogen oxides emissions resulted from conversion of the small amount of fuel-bound nitrogen in the fuel. Up to 90% conversion was observed with no apparent effect of any of the test variables. For typical gas-turbine operating conditions, all three pollutants were below levels which would permit the most stringent proposed automotive emissions standards to be met.

Anderson, D. N.↗
NASA NTRS1986

Opposed jet burner studies of silane-methane, silane-hydrogen and hydrogen diffusion flames with air

An atmospheric pressure tubular opposed jet burner technique was used to characterize certain diffusion-flame transitions and associated burning rates for N2-diluted mixtures of highly-reactive fuels. Presented are: (1) details of the technique, with emphasis on features permitting the study of flames involving pyrophoric gases and particle-forming combustion reactions: (2) discoveries on the properties of these flames which correspond to physically and chemically distinct stages of silane and hydrogen combustion; and (3) unburnt gas velocity data obtained from flames based on SiH4-CH4-N2, SiH4-H2-N2, and H2-N2 fuel mixtures, and plotted as functions of combustible-fuel mole fraction and fuel/oxygen molar input flow ratios. In addition, these burning velocity results are analyzed and interpreted.

Pellett, G. L.↗
NASA NTRS1924

Jet propulsion for airplanes

This report is a description of a method of propelling airplanes by the reaction of jet propulsion. Air is compressed and mixed with fuel in a combustion chamber, where the mixture burns at constant pressure. The combustion products issue through a nozzle, and the reaction of that of the motor-driven air screw. The computations are outlined and the results given by tables and curves. The relative fuel consumption and weight of machinery for the jet, decrease as the flying speed increases; but at 250 miles per hour the jet would still take about four times as much fuel per thrust horsepower-hour as the air screw, and the power plant would be heavier and much more complicated. Propulsion by the reaction of a simple jet can not compete with air screw propulsion at such flying speeds as are now in prospect.

Buckingham, Edgar↗
NASA NTRS1937

Effects of Air-Fuel Spray and Flame Formation in a Compression-Ignition Engine

High-speed motion pictures were taken at the rate of 2,500 frames per second of the fuel spray and flame formation in the combustion chamber of the NACA combustion apparatus. The compression ratio was 13.2 and the speed 1,500 revolutions per minute. An optical indicator was used to record the time-pressure relationship in the combustion chamber. The air-fuel ratio was varied from 10.4 to 365. The results showed that as the air-fuel ratio was increased definite stratification of the charge occurred in the combustion chamber even though moderate air flow existed. The results also showed the rate of vapor diffusion to be relatively slow.

Rothrock, A M↗
NASA NTRS1978

Tripropellant engine study

Engine performance data, combustion gas thermodynamic properties, and turbine gas parameters were determined for various high power cycle engine configurations derived from the space shuttle main engine that will allow sequential burning of LOX/hydrocarbon and LOX/hydrogen fuels. Both stage combustion and gas generator pump power cycles were considered. Engine concepts were formulated for LOX/RP-1, LOX/CH4, and LOX/C3H8 propellants. Flowrates and operating conditions were established for this initial set of engine systems, and the adaptability of the major components of shuttle main engine was investigated.

Wheeler, D. B.↗
NASA NTRS1986

Opposed jet burner studies of silane-methane, silane-hydrogen, and hydrogen diffusion flames with air

An atmospheric pressure tubular opposed jet burner technique was used to characterize certain diffusion-flame transitions and associated burning rates for N2-diluted mixtures of highly-reactive fuels. The paper presents: (1) details of the technique, with emphasis on features permitting the study of flames involving pyrophoric gases and particle-forming combustion reactions; (2) discoveries on the properties of these flames which correspond to physically and chemically distinct stages of silane and hydrogen combustion; and (3) unburnt gas velocity data obtained from flames based on SiH4-CH4-N2, SiH4-H2-N2, and H2-N2 fuel mixtures, and plotted as functions of combustible-fuel mole fraction and fuel/oxygen molar input flow ratios. In addition, these burning velocity results are analyzed and interpreted.

Pellett, G. L.↗
NASA NTRS1978

Effect of inlet temperature on the performance of a catalytic reactor

A 12 cm diameter by 15 cm long catalytic reactor was tested with No. 2 diesel fuel in a combustion test rig at inlet temperatures of 700, 800, 900, and 1000 K. Other test conditions included pressures of 3 and 6 x 10 to the 5th power Pa, reference velocities of 10, 15, and 20 m/s, and adiabatic combustion temperatures in the range 1100 to 1400 K. The combustion efficiency was calculated from measurements of carbon monoxide and unburned hydrocarbon emissions. Nitrogen oxide emissions and reactor pressure drop were also measured. At a reference velocity of 10 m/s, the CO and unburned hydrocarbons emissions, and, therefore, the combustion efficiency, were independent of inlet temperature. At an inlet temperature of 1000 K, they were independent of reference velocity. Nitrogen oxides emissions resulted from conversion of the small amount (135 ppm) of fuel-bound nitrogen in the fuel. Up to 90 percent conversion was observed with no apparent effect of any of the test variables. For typical gas turbine operating conditions, all three pollutants were below levels which would permit the most stringent proposed automotive emissions standards to be met.

Anderson, D. N.↗
NASA NTRS1991

Zeolites Remove Sulfur From Fuels

Zeolites remove substantial amounts of sulfur compounds from diesel fuel under relatively mild conditions - atmospheric pressure below 300 degrees C. Extracts up to 60 percent of sulfur content of high-sulfur fuel. Applicable to petroleum refineries, natural-gas processors, electric powerplants, and chemical-processing plants. Method simpler and uses considerably lower pressure than current industrial method, hydro-desulfurization. Yields cleaner emissions from combustion of petroleum fuels, and protects catalysts from poisoning by sulfur.

Voecks, Gerald E.↗
NASA NTRS1976

Performance and emission characteristics of swirl-can combustors to near-stoichiometric fuel-air ratio

Emissions and performance characteristics were determined for two full annular swirl-can combustors operated to near stoichiometric fuel-air ratio. Test condition variations were as follows: combustor inlet-air temperatures, 589, 756, 839, and 894 K; reference velocities, 24 to 37 meters per second; inlet pressure, 62 newtons per square centimeter; and fuel-air ratios, 0.015 to 0.065. The combustor average exit temperature and combustor efficiency were calculated from the combustor exhaust gas composition. For fuel-air ratios greater than 0.04, the combustion efficiency decreased with increasing fuel-air ratios in a near-linear manner. Increasing the combustor inlet air temperature tended to offset this decrease. Maximum oxides of nitrogen emission indices occurred at intermediate fuel-air ratios and were dependent on combustor design. Carbon monoxide levels were extremely high and were the primary cause of poor combustion efficiency at the higher fuel-air ratios. Unburned hydrocarbons were low for all test conditions. For high fuel-air ratios SAE smoke numbers greater than 25 were produced, except at the highest inlet-air temperatures.

Diehl, L. A.↗
NASA NTRS1978

Interaction between step fuel injectors on opposite walls in a supersonic combustor model

Results are presented from an experimental investigation of perpendicular, hydrogen fuel injection and combustion from opposing walls in a scramjet combustor model using a longitudinally staged laterally inline step-injection configuration. The model represents a portion of the flow in the Langley integrated modular scramjet engine combustor operating at a flight Mach number of 7. When operating at a ratio of jet pressure to free-stream dynamic pressure of 3, the injectors produce a bulk equivalence ratio of unity. This investigation represents part of a continuing study of the modular engine fuel injectors and is specifically designed to eliminate the adverse lateral pressure gradient observed at the injector location in a previous test. Flow survey contours at three axial locations, ranging from one-third of the engine combustor length to the total engine combustor length, are used to determine mixing efficiency and fuel distribution. Wall static pressures are analyzed by using one-dimensional theory to determine the combustion efficiency. Results show a significant improvement over previous injector designs tested in this duct geometry.

Mcclinton, C. R.↗
DOE OSTI2023

Zero-RK Acceleration of Low-Lifecycle-Carbon Fuel (LLCF) Simulations

Designing modern combustion systems now relies on computer models that predict how changes in design will affect performance. These models have replaced older methods that relied on the designer's intuition or costly and time-consuming physical testing. By using improved models, design cycles can be shortened, and cleaner and more efficient combustion devices can be created. This project aims to improve computer simulations of low-lifecycle-carbon fuels (LLCFs) with the goal of making these simulations faster and more accurate for predicting combustion in vehicles.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2024

Implementation of Surface Tension on a Reacting Flow Solver, PeleLM: Preprint

In liquid rocket engines, the fuel is supplied to the combustion chamber in the liquid state though injectors. Such fuel undergoes atomization, vaporization, and combustion processes. To design reliable and efficient injectors, it is required to understand the full processes. This research is part of an effort to develop a full atomization-vaporization-combustion solver from first principles. As an initial step to tackle the atomization process, a multiphase flow solver is under development. For the development, a library of the volume of fluid scheme for multiphase, IRL is coupled with a reacting Navier-Stokes equation solver, PeleLM. Furthermore, as the surface tension has considerable effects on spray breakup. surface tension is implemented in the momentum equation using the continuum surface force model and the improved height function technique.

height function↗
NASA NTRS2023

High-Pressure, Normal-Gravity Droplet Combustion Experimental Hardware

The High-Pressure, Trans-Critical (HPTC) 1-g Liquid Droplet Combustion Experiments will assess the autoignition and combustion of liquid fuel droplets at elevated temperatures and pressures. These experiments are being conducted at the NASA Glenn Research Center in a manner similar to experiments performed in Glenn’s Zero Gravity Research Facility (ZGF) using the B drop vehicle. The modification to the test capabilities of the ZGF experiments in the new experimental configuration will allow researchers to continue performing normal-gravity liquid droplet combustion experiments without requiring the use of the ZGF test equipment. These normal-gravity experiments will be conducted at lower pressures than in the ZGF because the pressure vessel for this setup is limited to a maximum working pressure of 7.74 atm (99.1 psig) at 366.5 K (200 °F). This experimental configuration will enable development of a similar capability for conducting high-pressure combustion and supercritical oxidation research on the International Space Station. Experiments will be conducted with the capability of altering the ambient pressure, temperature, and gas concentrations, as well as the fuel type for each test. For these experiments, the test vessel operates at pressures up to 7.5 atm (95.5 psig), temperatures up to 1,073 K (1,472 °F) inside the insulated oven, and oxygen concentrations up to 30 percent.

Droplet Combustion↗
NASA NTRS1981

Ignition and combustion: Low compression ratio, high output diesel

The feasibility of converting a spark ignition aircraft engine GTSI0-520 to compression ignition without increasing the peak combustion pressure of 1100 lbs/sq.in. was determined. The final contemplated utilized intake air heating at idle and light load and a compression ratio of about 10:1 with a small amount of fumigation (the addition of about 15% fuel into the combustion air before the cylinder). The engine used was a modification of a Continental-Teledyne gasoline engine cylinder from the GTSI0-520 supercharged aircraft engine.

Source record↗
NASA NTRSDate not supplied

Expanding the Capability of A Legacy Combustion Flametube to Test High Temperature Engine Materials in Relevant Environments

New materials and component designs are needed to advance gas turbine engine technology and provide the performance and efficiency needs for future applications. In order to advance these materials, testing in combustion environments is a critical step prior to engine testing. In this work, we detail the design and the fabrication of a materials test sector in a flametube combustor facility. The facility simulates a combustion environment similar to that experienced by components in gas turbine engines. The flow regime is characterized by a combination of high-temperature, high-velocity, high-heat flux, and high-velocity that components experience in gas turbine engines. Exposure of components in this facility allows for the study of combined environmental effects and the impact on both coating and substrate durability. The test facility may operate across a wide range of pressures from 275-400 psig (1,896-2,758 kPa) and an air flow rate of 5 lb/s (2.27 kg/s). While combustion gas temperature is expected in excess of 3,000°F (1,649°C), 900°F (482°C) cooling air may be supplied to the backside of components or test articles. The flametube combustor was previously used to evaluate fuel injectors and combustion products, and the new test configuration will also allow for materials exposure to complex, engine-like conditions. The interior of the Test Section was additively manufactured from GRCop-84 and cryogenically fit and brazed to a stainless steel 304 housing. The use of a copper liner minimizes welds and with active cooling, is expected to provide better durability over traditional hardware using stainless steel or Inconel with a ceramic liner. The Test Section has two opposing removable windows approximately 230 mm x 80 mm that can accommodate articles up to 85 mm tall. This modular design allows for custom platforms to hold coupons, panels, or airfoil shapes to be tested with minimal re-engineering or fabrication. The bolted joint and sealing remains consistent, so any new testing only needs to work within the existing design footprint. This paper will provide an overview of the facility capabilities, design considerations, as well as thermal and structural analysis of the hardware. Future testing of ceramic matrix composite (CMC) airfoils and advanced environmental barrier coatings (EBCs) will also be discussed.

Combustion↗