Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “feature selection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Spatiotemporal evolution of emission and absorption signatures in a laser-produced plasma

Here we report spatiotemporal evolution of emission and absorption signatures of Al species in a nanosecond (ns) laser-produced plasma (LPP). The plasmas were generated from an Inconel target, which contained ~0:4 wt. % Al, using 1064 nm, ≈6 ns full width half maximum pulses from an Nd:YAG laser at an Ar cover gas pressure of ≈34 Torr. The temporal distributions of the Al I (394.4 nm) transition were collected from various spatial points within the plasma employing time-of-flight (TOF) emission and laser absorption spectroscopy, and they provide kinetics of the excited state and ground state population of the selected transition. The emission and absorption signatures showed multiple peaks in their temporal profiles, although they appeared at different spatial locations and times after the plasma onset. The absorption temporal profiles showed an early time signature representing shock wave propagation into the ambient gas. We also used emission and absorption spectral features for measuring various physical properties of the plasma. The absorption spectral profiles are utilized for measuring linewidths, column density, and kinetic temperature, while emission spectra were used to measure excitation temperature. A comparison between excitation and kinetic temperature was made at various spatial points in the plasma. Our results highlight that the TOF measurements provide a resourceful tool for showing the spatiotemporal LPP dynamics with higher spatial and temporal resolution than is possible with spectral measurements but are difficult to interpret without additional information on excitation temperatures and linewidths. The combination of absorption and emission TOF and spectral measurements thus provides a more complete picture of LPP spatiotemporal dynamics than is possible using any one technique alone.

(140.3440) Laser-induced breakdown, (280.4788) Opt↗
DOE OSTI2025

Scoping Analysis of Pebble-Bed Reactors for the Destruction of the Transuranic Inventory of LWR Spent Nuclear Fuel

With the forecasted increase in the construction and operation of nuclear reactors, there will be a corresponding increase in the quantity of spent nuclear fuel (SNF) that requires long-term storage. In SNF, transuranic isotopes contribute the most to the long-term radiotoxicity of the fuel and pose a proliferation risk. One option that has been explored to address these issues is the removal of the transuranic isotopes from SNF and the conversion of these isotopes into transuranic fuel (TRU fuel). Here, this work sought to determine how effective a micro-modular Pebble-Bed High-Temperature Gas-Cooled Reactor (PB-HTGR); the 10-MW High Temperature Gas-cooled Test Reactor (HTR-10); and a salt-cooled small-modular pebble-bed reactor (PBR), i.e. the generic Fluoride-cooled High-temperature Reactor (gFHR), are at reducing the inventory of transuranic isotopes while still maintaining the intrinsic safety features of the PBR designs, such as negative temperature coefficients of reactivity. Optimized pebble designs utilizing TRU fuel were found for both reactors through the adjustment for the packing fraction of fuel in each pebble. The Axial Zone Equilibrium Modeling (A-ZEM) method was used in this work to help select the optimized pebble design. Once an optimized pebble design was selected and an equilibrium model was produced, the results from the deep burn (DB) HTR-10 and gFHR designs were compared to the results of two models from the literature. While both the DB gFHR and the DB HTR-10 were able to reduce the weapons-usable transuranic inventory, the performance of these reactors did not match that of the small-modular PB-HTGRs in the literature. Therefore, a need was identified for further refinement of the gFHR design using TRU fuel, as the results for this model were more promising than those of the DB HTR-10, which was strongly limited by the high leakage intrinsic to micro-modular PB-HTGRs.

Transuranic fuel↗
DOE OSTI2024

Evaluation of DED and LPBF Fe-based Alloys Process Application Envelopes based on Performance, Process Economics, Supply Chain Risks, and Reactor-specific Targeted Components

The U.S. Department of Energy (DOE), Office of Nuclear Energy (NE), Advanced Materials and Manufacturing Technologies (AMMT) program aims to develop extreme-environment materials solutions for use in the deployment of advanced nuclear reactors and the sustainment of the current fleet. To achieve this objective, a combination of experiment, a computational tool, and machine learning (ML) for the design of materials is adopted for the maturation of materials for nuclear technology. Through advanced manufacturing techniques such as laser powder bed fusion (LPBF) and laser powder direct energy deposition (LP-DED), components with complex geometries can be fabricated with reduced time and effort. Such advanced manufacturing methods can also provide the opportunity to improve materials performance through optimized microstructures and mechanical properties. However, existing engineering alloys are not always well suited for fabrication with additive manufacturing (AM), as their compositions have been tuned to optimize fabrication via conventional methods. Thus, similar alloys with modified compositions that are better suited for AM can be studied for improved performance. Over the past three years, the AMMT teams from Argonne National Laboratory (ANL) and Pacific Northwest National Laboratory (PNNL) studied various known Fe-based alloys by evaluating their initial printability using LPBF, and an AMMT-developed down-selection and decision matrix reduced the number of alloys to be studied from six to three in fiscal year (FY) 2024. Additionally, in FY 2024, for parallel evaluation, these three alloys were studied using LPDED. While LPBF is better for small- to medium-sized components with high detail and internal features, LP-DED combines a material feed system to place the powder onto the exact spot where the laser will melt the material. This AM method can be easily scaled to extremely large components and provides high build rate speeds compared to those of conventional LPBF systems. Additionally, DED is a better choice for complex geometries and compositional gradients.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Control, Fault Management, and Grid Support Functionality of an MV AC-DC Solid State Transformer based EV Extreme Fast Charging Station

Electric vehicles (EVs) have become increasingly popular in recent times while revolutionizing the consumer and commercial transportation market. The development of charging infrastructure has become one of the priorities for increasing the adoption of EVs. Extreme fast charging (XFC) technology can reduce the so-called ’range anxiety’ of consumers as they significantly reduce the charging time. With the advent of wide band-gap (WBG) power devices and improvement in power electronic converters, medium voltage (MV) solid state transformer (SST) based XFC system has the potential to replace the traditional XFC stations because of the lower footprint, ease of installation, enhanced control feature, and better system efficiency. The control system design is one of the critical aspects of the SST development process. Careful consideration and detailed analysis are required to find out suitable control method for the SST based on its topology among different centralized and decentralized control architectures. Also, the control parameters selection and potential improvement to the transient response of the controller ought to be investigated. Another major concern of the SST is different types of internal fault which reduces the overall reliability of the XFC system. As a result, designing a robust protection system is essential. Among different fault modes, open circuit switch faults have received significant attention as an active research area because of their likelihood and severe effects on converters. Therefore, the power stages used in the XFC system require functional and accurate open circuit switch fault management methods. An equally significant aspect of this SST based XFC is its compatibility in a microgrid where there is no synchronous generator present. When the grid is not available, the XFC SSTs can provide grid forming capability and continue supplying the critical loads in islanded mode. The transition between grid connected and islanded mode, especially the grid resynchronization process has to be carefully performed for the safety of the microgrid components. The challenges posed by the aforementioned issues have inspired the work done in this dissertation. Here, a 13.2 kV, 1 MVA, AC/DC SST for the XFC system is examined and a comparative analysis is conducted to select the control architecture based on feasibility of implementation and performance. A detailed control parameter design process is demonstrated considering the sensor dynamics and delay. The selected decentralized control method is augmented by introducing a novel sensor-less load current feedforward method to provide better voltage regulation at the DC bus during a change of load. Next, in the fault management section, a hierarchical failure mode effect analysis (FMEA) is proposed to enable a systematic design of the internal fault protection of the XFC SST as there are limited examples in the literature regarding the analysis of the safety and design of the protection of a power electronic converter system. Novel open circuit switch fault management methods for the converters in the system are presented. Finally, XFC SST based MV microgrid operations in grid connected mode and islanded mode are explored. A secondary control method for grid resynchronization is presented and a design process of control parameters is shown to ensure the stability of the secondary voltage and frequency regulation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

The Zintl Concept Applied to Intergrowth Structures: Electron‐Hole Matching, Stacking Preferences, and Chemical Pressures in Pd 5 InAs

Abstract Enumerating the potential stacking sequences of layers is a fundamental way to account for the structure diversity of solid state compounds. In many cases, these stacking variations represent polymorphs with only small energetic differences. Here, we examine a compound for which the preferred stacking pattern instead reveals key aspects about its chemical bonding: Pd 5 InAs. Its structure is based on the intergrowth of slabs of the AuCu 3 and PtHg 2 (or alternatively, fluorite) structure types. Two basic stacking arrangements are available to this compound, represented by the Pd 5 TlAs and HoCoGa 5 structure types. DFT total energy calculations reveal that the former outcompetes the latter by a staggering 0.65 eV/formula unit. Through a combination of DFT‐reversed approximation Molecular Orbital (DFT‐raMO) and DFT‐Chemical Pressure (DFT‐CP) analysis we trace this preference to two factors. First, with DFT‐raMO analysis, we derive a Zintl‐like bonding scheme of Pd 5 InAs. This scheme, along with the inspection of selected crystal orbitals, is then connected to preferred stacking through the coordination environments of the Pd atoms at the interface between the Pd−In and Pd−As layers. In the hypothetical HoCoGa 5 ‐type and observed Pd 5 InAs‐type structures, different Pd coordination environments arise at the interfaces. The hypothetical structure features square planar PdIn 2 As 2 units, in each of which the same 4d‐orbital serves in the Pd sublattice's role as both Lewis acid (for interactions with the As) and Lewis base (for interactions with the In). In the observed structure, tetrahedral PdIn 2 As 2 units occur instead, so that these contradictory roles are distributed to separate 4d‐orbitals, leading to more effective bonding. DFT‐CP analysis illustrates that this driving force for the Pd 5 TlAs‐type arrangement is supplemented by a favorable alignment of the packing tensions in the parent structures. Altogether, the resulting picture demonstrates how the reaction of simple intermetallic structures to form intergrowths can be guided by recognizable chemical interactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Broadly neutralizing anti-S2 antibodies protect against all three human betacoronaviruses that cause deadly disease

Pan-betacoronavirus neutralizing antibodies may hold the key to developing broadly protective vaccines against novel pandemic coronaviruses and to more effectively respond to SARS-CoV-2 variants. The emergence of Omicron and subvariants of SARS-CoV-2 illustrates the limitations of solely targeting the receptor-binding domain (RBD) of the spike (S) protein. Here, we isolated a large panel of broadly neutralizing antibodies (bnAbs) from SARS-CoV-2 recovered-vaccinated donors, which targets a conserved S2 region in the betacoronavirus spike fusion machinery. Select bnAbs showed broad in vivo protection against all three deadly betacoronaviruses, SARS-CoV-1, SARS-CoV-2, and MERS-CoV, which have spilled over into humans in the past two decades. Structural studies of these bnAbs delineated the molecular basis for their broad reactivity and revealed common antibody features targetable by broad vaccination strategies. These bnAbs provide new insights and opportunities for antibody-based interventions and for developing pan-betacoronavirus vaccines.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2022

Localized Phonon Densities of States at Grain Boundaries in Silicon

Since it is now possible to record vibrational spectra at nanometer scales in the electron microscope, it is of interest to explore whether extended defects in crystals such as dislocations or grain boundaries will result in measurable changes of the phonon densities of states (dos) that are reflected in the spectra. Phonon densities of states were calculated for a set of high angle grain boundaries in silicon. The boundaries are modeled by supercells with up to 160 atoms, and the vibrational densities of states were calculated by taking the Fourier transform of the velocity–velocity autocorrelation function from molecular dynamics simulations with larger supercells doubled in all three directions. In selected cases, the results were checked on the original supercells by comparison with the densities of states obtained by diagonalizing the dynamical matrix calculated using density functional theory. Near the core of the grain boundary, the height of the optic phonon peak in the dos at 60 meV was suppressed relative to features due to acoustic phonons that are largely unchanged relative to their bulk values. This can be attributed to the variation in the strength of bonds in grain boundary core regions where there is a range of bond lengths.

Materials Science↗
DOE OSTI2021

The Phase-2 Upgrade of the CMS Data Acquisition

The High Luminosity LHC (HL-LHC) will start operating in 2027 after the third Long Shutdown (LS3), and is designed to provide an ultimate instantaneous luminosity of 7:5 × 10$^{34}$ cm$^{-2}$ s$^{-1}$, at the price of extreme pileup of up to 200 interactions per crossing. The number of overlapping interactions in HL-LHC collisions, their density, and the resulting intense radiation environment, warrant an almost complete upgrade of the CMS detector. The upgraded CMS detector will be read out by approximately fifty thousand highspeed front-end optical links at an unprecedented data rate of up to 80 Tb/s, for an average expected total event size of approximately 8 - 10 MB. Following the present established design, the CMS trigger and data acquisition system will continue to feature two trigger levels, with only one synchronous hardware-based Level-1 Trigger (L1), consisting of custom electronic boards and operating on dedicated data streams, and a second level, the High Level Trigger (HLT), using software algorithms running asynchronously on standard processors and making use of the full detector data to select events for offline storage and analysis. The upgraded CMS data acquisition system will collect data fragments for Level-1 accepted events from the detector back-end modules at a rate up to 750 kHz, aggregate fragments corresponding to individual Level- 1 accepts into events, and distribute them to the HLT processors where they will be filtered further. Events accepted by the HLT will be stored permanently at a rate of up to 7.5 kHz. This paper describes the baseline design of the DAQ and HLT systems for the Phase-2 of CMS.

Badaro, Gilbert↗
DOE OSTI2023

Structural basis of the amidase ClbL central to the biosynthesis of the genotoxin colibactin

Colibactin is a genotoxic natural product produced by select commensal bacteria in the human gut microbiota. The compound is a bis-electrophile that is predicted to form interstrand DNA cross-links in target cells, leading to double-strand DNA breaks. The biosynthesis of colibactin is carried out by a mixed NRPS–PKS assembly line with several noncanonical features. An amidase, ClbL, plays a key role in the pathway, catalyzing the final step in the formation of the pseudodimeric scaffold. ClbL couples α-aminoketone and β-ketothioester intermediates attached to separate carrier domains on the NRPS–PKS assembly. Here, the 1.9 Å resolution structure of ClbL is reported, providing a structural basis for this key step in the colibactin biosynthetic pathway. The structure reveals an open hydrophobic active site surrounded by flexible loops, and comparison with homologous amidases supports its unusual function and predicts macromolecular interactions with pathway carrier-protein substrates. Modeling protein–protein interactions supports a predicted molecular basis for enzyme–carrier domain interactions. Overall, the work provides structural insight into this unique enzyme that is central to the biosynthesis of colibactin.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

SYSTEMATIC MULTI-INDEX VALIDATIONS OF SIDI ENGINE FLOW FIELD LES COMPUTATIONS USING CRANK ANGLE-RESOLVED PIV MEASUREMENTS

In-cylinder flow fields make significant impacts on the fuel atomization, fuel mixture formation, and combustion process in spark ignition direct injection (SIDI) engines. In recent years, model-based simulation approaches are preferred in regard to investigating the transient in-cylinder flow field characteristics. Most commonly, the simulation models are validated using single representative flow field at a typical crank angle measured by particle image velocimetry (PIV). However, it provides only limited knowledge about the flow field which is highly three-dimensional and of transient nature. In this study, crank angle-resolved Ply measurements are conducted on three distinct planes inside the cylinder to capture the transient process of flow field characteristics which vary with the crank angle. These three planes consist of one tumble plane through the spark plug tip, one tumble plane along two intake ports, and one swirl plane at 30 mm below the cylinder head. Large eddy simulation (LES) is employed for the numerical computations using the CONVERGE codes. On the basis of large datasets for both temporal and spatial domains, a multi-index systematic validation approach is conducted. Crank angle-resolved calculations of global indices and local indices are implemented using the flow fields velocity data obtained from both PIV and LES on select planes. Global indices reveal the trends in similarities of different crank angle degrees and locations, while local indices give the detail comparison results. In summary, with the systematic multi-index validation approach, the crucial crank angle degrees and locations for model verification will be detected. Furthermore, the corresponding critical flow features are analyzed. Practical guideline of flow field validation is proposed.

Crank angle-resolved PIV↗
DOE OSTI2025

The Composite Spectrum of QSO Absorption Line Systems in DESI DR2

We present details regarding the construction of a composite spectrum of quasar (QSO) absorption line systems. In this composite spectrum we identify more than 70 absorption lines, and observe oxygen and hydrogen emission features at a higher signal-to-noise ratio than in any previous study. As the light from a distant quasar travels towards an observer, it may interact with the circumgalactic medium environment of an intervening galaxy, forming absorption lines. In order to maximize the signal of these absorption lines, we have selected a sample of 238,838 quasar spectra from the second data release of the Dark Energy Spectroscopic Instrument (DESI), each identified to have absorption lines resulting from such an interaction. By stacking these spectra in the restframe of the absorption, and calculating a median composite spectrum, we are able to isolate and enhance these absorption lines. We provide a full atlas of all detected absorption and emission lines as well as their fit centroids and equivalent width values. This atlas should aid in future studies investigating the compositions and physical conditions of these absorbers.

Napolitano, Lucas [Wyoming U.] (ORCID:000000025166↗
DOE OSTI2025

Automation for Electric Vehicle Battery Pack Disassembly

Battery‐electric vehicles (EVs) are growing exponentially. The demand for these batteries is expected to increase sevenfold by 2035. The EV batteries reach their end of life when the capacity fades to 70%–80% of new, with some being removed from the primary applications with even lower levels of degradation. These batteries can be used in less demanding applications. The disassembly process is currently manual, slow, unsafe, and expensive. Automation is needed to increase the throughput. EV battery packs feature various continually changing designs and form factors, which limit the usefulness of deterministically programmed robotic solutions. The conceptual robotic disassembly of EV batteries has attracted the attention of researchers. However, while many approaches have been proposed, practical implementations are lacking. Here, we review proposed concepts for EV battery disassembly and describe the selected approach, with elements of partial solutions validated in a laboratory setting, including the selection of commercial solutions, the development of custom end effectors, and methodologies for detection, localization, and classification of fasteners. The computer vision tasks employed an overhead 2D camera to detect the type of battery pack and approximate localization of fasteners, and a 3D camera mounted on the robotic arm for precise localization (position and tilt) and classification.

Islam, Abu [Rochester Inst. of Technology, Rochest↗
DOE OSTI2023

Searching for Milky Way twins: Radial abundance distribution as a strict criterion

We search for Milky Way-like galaxies among a sample of approximately 500 galaxies. The characteristics we considered of the candidate galaxies are the following: stellar mass M $\star$ , optical radius R 25 , rotation velocity V rot , central oxygen abundance (O/H) 0 , and abundance at the optical radius (O/H) R 25 . If the values of R 25 and M $\star$ of the galaxy were close to that of the Milky Way, then the galaxy was referred to as a structural Milky Way analogue (sMWA). The oxygen abundance at a given radius of a galaxy is defined by the evolution of that region (astration level, that is, the fraction of gas converted into stars, as well as gas exchange with the surroundings), and we then assumed that the similarity of (O/H) 0 and (O/H) R 25 in two galaxies suggests a similarity in their (chemical) evolution. If the values of (O/H) 0 and (O/H) R 25 in the galaxy were close to that of the Milky Way, then the galaxy was referred to as an evolutionary Milky Way analogue (eMWA). If the galaxy was simultaneously an eMWA and sMWA, then the galaxy was considered a Milky Way twin. We find that the position of the Milky Way on the (O/H) 0 –(O/H) R 25 diagram shows a large deviation from the general trend in the sense that the (O/H) R 25 in the Milky Way is appreciably lower than in other galaxies of similar (O/H) 0 . This feature of the Milky Way evidences that its (chemical) evolution is not typical. We identify four galaxies (NGC 3521, NGC 4651, NGC 2903, and MaNGA galaxy M-8341-09101) that are simultaneously sMWA and eMWA and can therefore be considered as Milky Way twins. In previous studies, Milky Way-like galaxies were selected using structural and morphological characteristics, that is, sMWAs were selected. We find that the abundances at the centre and at the optical radius (evolutionary characteristics) provide a stricter criterion for selecting real Milky Way twins.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Evidence for C and Mg variations in the GD-1 stellar stream

ABSTRACT Dynamically cold stellar streams are the relics left over from globular cluster dissolution. These relics offer a unique insight into a now fully disrupted population of ancient clusters in our Galaxy. Using a combination of Gaia eDR3 proper motions, optical and near-UV colours, we select a sample of likely Red Giant Branch stars from the GD-1 stream for medium-low resolution spectroscopic follow-up. Based on radial velocity and metallicity, we are able to find 14 new members of GD-1, 5 of which are associated with the spur and blob/cocoon off-stream features. We measured C-abundances to probe for abundance variations known to exist in globular clusters. These variations are expected to manifest in a subtle way in globular clusters with such low masses ($\sim 10^4\,{\rm ~\textrm {M}_\odot }$) and metallicities ([Fe/H] ∼ −2.1 dex). We find that the C-abundances of the stars in our sample display a small but significant (3σ level) spread. Furthermore, we find ∼3σ variation in Mg-abundances among the stars in our sample that have been observed by APOGEE. These abundance patterns match the ones found in Galactic globular clusters of similar metallicity. Our results suggest that GD-1 represents another fully disrupted low-mass globular cluster where light-element abundance spreads have been found.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Co-design of Advanced Architectures for Graph Analytics using Machine Learning

A graph is an excellent way of representing relationships among entities. We can use graph analytics to synthesize and analyze such relational data, and extract relevant features that are useful for various tasks such as machine learning. Considering the crucial role of graph analytics in various domains, it is important and timely to investigate the right hardware configurations that can achieve optimal performance for graph workloads on future high-performance computing systems. Design space exploration studies facilitate the selection of appropriate configurations (e.g. memory) to achieve a desired system performance. Recently, the approach of accelerating graph analytics using persistent non-volatile memory has gained a lot of attention. Traditional system simulators such as Gem5 and NVMain can be used to explore the design space of these advanced memory architectures for graph workloads. However, these simulators are slow in execution thus limiting the efficiency of design space exploration studies. To overcome this challenge, we proposed a machine learning based approach to co-design advanced memory architectures for graph workloads. We tested our approach with DRAM, non-volatile memory, and hybrid memory (DRAM+NVM) using a breadth first search benchmark algorithm. Our results showed the applicability of the proposed machine learning based approach to the co-design of the advanced memory architectures. In this paper, we provide recommendations on selecting advanced memory architectures to achieve desired performance for graph workloads. We also discuss the performances of different machine learning models that were considered in this study.

Kurte, Kuldeep↗
DOE OSTI2025

Pathway Selectivity in 2D Electronic‐Vibrational Spectroscopy with Quantum Light

Abstract Pathway selectivity in quantum spectroscopy with entangled photons is a powerful spectroscopic tool. Phase‐matched signals involving classical light contain contributions from multiple material pathways, whereas quantum spectroscopy may allow the selection of individual pathways. 2D electronic‐vibrational spectroscopy (2DEVS) is a four‐wave mixing technique which employs visible and infrared entangled photons. It is showed how the three contributing pathways—ground state bleach, excited state absorption, and excited state emission—can be separated by photon‐number‐resolved coincidence measurements. Entangled photons thus reveal spectral features not visible in the classical signal, with an enhanced spectral resolution.

Jadoun, Deependra [Department of Chemistry Univers↗
DOE OSTI2026

Inverse design of hypoeutectoid pearlite steel microstructures using a deep learning and genetic algorithm optimization framework

Goal-oriented microstructure design in metallic materials is a challenging task due to complex structure-property relationships. Traditional experimental and computational approaches are time-intensive and economically inefficient, limiting their applicability for large-scale design space exploration. Here, in this work, we propose an end-to-end framework that integrates deep learning models with genetic optimization to design microstructures with targeted mechanical properties. Deep learning models enable accurate forward design, while their integration with genetic optimization enables efficient inverse design within a few hours, compared to days or weeks using conventional finite element simulations. The framework combines experimental characterization and finite element modeling to analyze the influence of microstructural features on the mechanical behavior of hypoeutectoid steels. Data from both experiments and simulations are used to train the deep learning models. To demonstrate its effectiveness, we apply the framework to 0.63% carbon steel with proeutectoid ferrite and pearlite phases, commonly used in industrial applications. In this study, 2D microstructures were used for modeling, selected primarily for computational efficiency and to establish proof of concept. The framework successfully optimizes microstructures for targeted yield strength, ultimate strength, and stress concentration factors while significantly reducing computational time. Beyond hypoeutectoid steels, this scalable framework can be extended to other material systems and integrated with additive manufacturing, offering an efficient approach for accelerating microstructure design for specific engineering applications.

ConvLSTM↗
DOE OSTI2020

CRADA Final Report: CRADA Number NFE-18-07341 with Eonix LLC

Over the past two years, my work has been focused on the development of a commercially viable electrolyte that expands the voltage window of ultracapacitors featuring standard activated carbon electrodes from 2.7V to greater than 3V. During this fellowship in collaboration with staff at Oak Ridge National Laboratory, we refined a high throughput screening process to rapidly analyze the properties and performance of electrolyte candidates in ultracapacitors and establish a quantitative structure activity relationship (QSAR) methodology for candidate selection. Over sixty electrolyte chemistries were screened using these novel techniques.

42 ENGINEERING↗