Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Neutron Spin Rotation at Laue Diffraction in a Weakly Deformed Transparent Crystal with No Center of Symmetry

The effect of neutron spin rotation at Laue diffraction in a weakly deformed neutron-transparent noncentrosymmetric crystal has been described theoretically and studied experimentally. The effect is due to the bending of a Kato trajectory of the neutron in the deformed crystal. At a certain type of deformation, one of two neutron waves excited at Laue diffraction, which propagate in opposite crystal fields in the crystal with no center of symmetry, leaves the crystal. As a result, the spin of the remaining neutron wave is rotated by a certain angle with respect to initial direction due to the interaction of the magnetic moment of a moving neutron with the crystalline electric field. This effect is absent in an undeformed perfect crystal, where only the depolarization of a beam occurs because both waves in opposite electric fields have the same amplitude. A method has been developed for controlled deforming the perfect single crystal by creating a temperature gradient in it. Thereby, a new possibility of measuring electric fields acting on a neutron in noncentrosymmetric crystals, as well as a method of controlling these fields in experiments on studying the fundamental properties of the neutron, has been implemented.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanical Deformation of a Lithium-Metal Anode Due to a Very Stiff Separator

This work builds on the two-dimensional model presented by Ferrese et al. [J. Electrochem. Soc., 159, A1615 (2012)1, which captures the movement of lithium metal at the negative electrode during cycling in a Li-metal/LiCoO2 cell. In this paper, the separator is modeled as a dendrite-inhibiting polymer separator with an elastic modulus of 16 GPa. The separator resists the movement of lithium through the generation of stresses in the cell. These stresses affect the negative electrode through two mechanisms altering the thermodynamics of the negative electrode and deforming the negative electrode mechanically. From this analysis, we find that the dendrite-inhibiting separator causes plastic and elastic deformation of the lithium at the negative electrode which flattens the electrode considerably when compared to the liquid-electrolyte case. This flattening of the negative electrode causes only very slight differences in the local state of charge in the positive electrode. When comparing the magnitude of the effects flattening the negative electrode, we find that the plastic deformation plays a much larger role than either the pressure-modified reaction kinetics or elastic deformation. This is due to the low yield strength of the lithium metal, which limits the stresses such that they have only a small effect on the reaction kinetics. (C) 2014 The Electrochemical Society. All rights reserved.

Ferrese, A↗

A deformation-dependent coupled Lagrangian/semi-Lagrangian meshfree hydromechanical formulation for landslide modeling

Abstract The numerical modelling of natural disasters such as landslides presents several challenges for conventional mesh-based methods such as the finite element method (FEM) due to the presence of numerically challenging phenomena such as severe material deformation and fragmentation. In contrast, meshfree methods such as the reproducing kernel particle method (RKPM) possess unique features conducive to modelling extreme events such as the absence of a structured mesh and the ease of adaptive refinement, among others. While the semi-Lagrangian reproducing kernel (SL-RK) shape functions of RKPM defined in the current configuration have proven to be effective in extreme event modelling, the computational cost for the re-evaluation of the shape functions at every time step is costly. In this work, a deformation-dependent coupling of the Lagrangian reproducing kernel (L-RK) and SL-RK approximations is proposed for the solution of a hydro-mechanical formulation for effective simulations of landslides. The ramp function is constructed based on an equivalent plastic strain as a deformation-dependent transition from L-RK shape functions to SL-RK ones as the deformation progresses. The particular focus of the paper will be on modelling seepage-induced landslides with a mixed $$u$$ u – $$p$$ p formulation to couple the solid and fluid phases. Examples are presented to examine the effectiveness of this coupled Lagrangian/semi-Lagrangian reproducing kernel (L–SL RK) formulation and to highlight its performance in landslide modelling.

Baek, Jonghyuk↗

Spatio-temporal modeling and optimization of a deformable-grating compressor for short high-energy laser pulses

Monolithic large-scale diffraction gratings are desired to improve the performance of high-energy laser systems and scale them to higher energy, but the surface deformation of these diffraction gratings induce spatio-temporal coupling that is detrimental to the focusability and compressibility of the output pulse. A new deformable-grating-based pulse compressor architecture with optimized actuator positions has been designed to correct the spatial and temporal aberrations induced by grating wavefront errors. An integrated optical model has been built to analyze the effect of grating wavefront errors on the spatio-temporal performance of a compressor based on four deformable gratings. Moreover, a 1.5-meter deformable grating has been optimized using an integrated finite-element-analysis and genetic-optimization model, leading to spatio-temporal performance similar to the baseline design with ideal gratings.

36 MATERIALS SCIENCE↗

The role of irradiation on deformation-induced martensitic phase transformations in face-centered cubic alloys

Localized deformation, including that by the deformation-induced shearing martensitic phase transformation, is responsible for hardening and embrittlement in irradiated face-centered cubic alloys. These localized deformation processes can have profound consequences on the mechanical integrity of common structural metals used in extreme radiation environments such as nuclear reactors. This article aims to review and understand exactly how irradiation affects the martensitic phase transformation in face-centered cubic alloys, with an emphasis on austenitic stainless steel, given its ubiquity in the archival literature. The influence of irradiation on stacking fault energy and subsequent implications on the phase transformation are discussed. Mechanisms by which irradiation-induced microstructures enhance the phase transformation are also described, including the surface energy contribution of irradiation-induced cavities (i.e., voids and bubbles) toward the critical martensite nucleation energy, and partial dislocation–cavity interactions. In conclusion, a deformation mechanism map illustrates how irradiation-induced cavities can modulate the martensitic transformation pathway.

36 MATERIALS SCIENCE↗

3D deformation field throughout the interior of materials.

This report contains the one-year feasibility study for our three-year LDRD proposal that is aimed to develop an experimental technique to measure the 3D deformation fields inside a material body. In this feasibility study, we first apply Digital Volume Correlation (DVC) algorithm to pre-existing in-situ Xray Computed Tomography (XCT) image sets with pure rigid body translation. The calculated displacement field has very large random errors and low precision that are unacceptable. Then we enhance these tomography images by setting threshold of the intensity of each slice. DVC algorithm is able to obtain accurate deformation fields from these enhanced image sets and the deformation fields are consistent with the global mechanical loading that is applied to the specimen. Through this study, we prove that the internal markers inside the pre-existing tomography images of aluminum alloy can be enhanced and are suitable for DVC to calculate the deformation field throughout the material body.

Jin, Huiqing↗

Development of Advanced Continuum Models that Incorporate Nanomechanical Deformation into Engineering Analysis

Materials with characteristic structures at nanoscale sizes exhibit significantly different mechanical responses from those predicted by conventional, macroscopic continuum theory. For example, nanocrystalline metals display an inverse Hall-Petch effect whereby the strength of the material decreases with decreasing grain size. The origin of this effect is believed to be a change in deformation mechanisms from dislocation motion across grains and pileup at grain boundaries at microscopic grain sizes to rotation of grains and deformation within grain boundary interface regions for nanostructured materials. These rotational defects are represented by the mathematical concept of disclinations. The ability to capture these effects within continuum theory, thereby connecting nanoscale materials phenomena and macroscale behavior, has eluded the research community. The goal of our project was to develop a consistent theory to model both the evolution of disclinations and their kinetics. Additionally, we sought to develop approaches to extract continuum mechanical information from nanoscale structure to verify any developed continuum theory that includes dislocation and disclination behavior. These approaches yield engineering-scale ex-pressions to quantify elastic and inelastic deformation in all varieties of materials, even those that possess highly directional bonding within their molecular structures such as liquid crystals, covalent ceramics, polymers and biological materials. This level of accuracy is critical for engineering design and thermo-mechanical analysis is performed in micro- and nano systems. The research proposed here innovates on how these nanoscale deformation mechanisms should be incorporated into a continuum mechanical formulation, and provides the foundation upon which to develop a means for predicting the performance of advanced engineering materials.

Zimmerman, Jonathan A.↗

A non-linear elastic constitutive framework for replicating plastic deformation in solids.

Ductile metals and other materials typically deform plastically under large applied loads; a behavior most often modeled using plastic deformation constitutive models. However, it is possible to capture some of the key behaviors of plastic deformation using only the framework for nonlinear elastic mechanics. In this paper, we develop a phenomenological, hysteretic, nonlinear elastic constitutive model that captures many of the features expected of a plastic deformation model. This model is based on calculating a secant modulus directly from a material s stress-strain curve. Scalar stress and strain values are obtained in three dimensions by using the von Mises invariants. Hysteresis is incorporated by tracking an additional history variable and assuming an elastic unloading response. This model is demonstrated in both single- and multi-element simulations under varying strain conditions.

Roberts, Scott Alan↗

Elevated and Low Temperature Deformation of Cast Depleted Uranium

Goals: Understand crystal structure and micro-structure changes during high and low temperature deformation of uranium, in particular texture, and develop constitutive micro-structure based model for uranium deformation. Deliverables achieved: Completed texture measures for 11 pre- and post-dU compression samples, quantified texture pre- and post-deformation, and provided data to constrain deformation models.

Materials Science(36)↗

Appraisal of Transport and Deformation in Shale Reservoirs using Natural Noble Gas Tracers

This report presents efforts to develop the use of in situ naturally-occurring noble gas tracers to evaluate transport mechanisms and deformation in shale hydrocarbon reservoirs. Noble gases are promising as shale reservoir diagnostic tools due to their sensitivity of transport to: shale pore structure; phase partitioning between groundwater, liquid, and gaseous hydrocarbons; and deformation from hydraulic fracturing. Approximately 1.5-year time-series of wellhead fluid samples were collected from two hydraulically-fractured wells. The noble gas compositions and isotopes suggest a strong signature of atmospheric contribution to the noble gases that mix with deep, old reservoir fluids. Complex mixing and transport of fracturing fluid and reservoir fluids occurs during production. Real-time laboratory measurements were performed on triaxially-deforming shale samples to link deformation behavior, transport, and gas tracer signatures. Finally, we present improved methods for production forecasts that borrow statistical strength from production data of nearby wells to reduce uncertainty in the forecasts.

02 PETROLEUM↗

Experimental deformation in sandstone, carbonates and quartz aggregate

The first part of my thesis is mainly focused on the effect of grain size distribution on compaction localization in porous sandstone. To identify the microstructural parameters that influence compaction band formation, I conducted a systematic study of mechanical deformation, failure mode and microstructural evolution in Bleurswiller and Boise sandstones, of similar porosity (~25%) and mineralogy but different sorting. Discrete compaction bands were observed to develop over a wide range of pressure in the Bleurswiller sandstone that has a relatively uniform grain size distribution. In contrast, compaction localization was not observed in the poorly sorted Boise sandstone. My results demonstrate that grain size distribution exerts important influence on compaction band development, in agreement with recently published data from Valley of Fire and Buckskin Gulch, as well as numerical studies. The second part aimed to improve current knowledge on inelastic behavior, failure mode and brittle-ductile transition in another sedimentary rock, porous carbonates. A micritic Tavel (porosity of ~13%) and an allochemical Indiana (~18%) limestones were deformed under compaction in wet and dry conditions. At lower confining pressures, shear localization occurred in brittle faulting regime. Through transitional regime, the deformation switched to cataclastic flow regime at higher confining pressure. Specifically in the cataclastic regime, the (dry and wet) Tavel and dry Indiana failed by distributed cataclastic flow, while in contrast, wet Indiana failed as compaction localization. My results demonstrate that different failure modes and mechanical behaviors under different deformation regimes and water saturation are fundamental prior to any geophysical application in porous carbonates. The third part aimed to focus on investigating compaction on quartz aggregate starting at low (MPa) using X-ray diffraction. We report the diffraction peak evolution of quartz with increasing pressures. Through evaluating the unit cell lattice parameters and the volume of the quartz sample, macroscopic stress and strain were resolved. Moreover, we observed quartz peak broadened asymmetrically at low pressure, such extent is more prominent in axial than in radial direction. Our evaluation on peak [101] (highest intensity among peaks) demonstrated that full width at half maximum can be a good proxy for microscopic stress distribution. We observed deviations in the pressurevolume curves at P = ~0.4 GPa and speculated that it was the point of which onset of grain crushing and pore collapse occur in quartz. This is on the same order of which onset of grain crushing (commonly known as P*) is observed in sandstones in the rock mechanics literature. This demonstrated that there is potential in estimating grain crushing and pore collapse pressure with our technique.

58 GEOSCIENCES↗

Deformation Behavior in Neutron Irradiated Generation II FeCrAl Alloys for Accident Tolerant Fuel Cladding

Preliminary work has been completed to evaluate the deformation behavior of the Generation II FeCrAl alloy class. The Generation II alloy, C35M, was neutron irradiated within the High Flux Isotop e Reactor followed by post-irradiation examination to evaluate the mechanical properties, irradiated microstructure, deformation modes, and deformation microstructure. Complementary characterization techniques were used in this evaluation. It was found tha t aft er irradiation to1.8 dpa at 364 °C that the C35M specimen failed in a ductile manner. The observed deformation microstructure showed a high density of line dislocations, dislocation networks, and dislocation pile-ups. The observed performance and stru cture s are consistent with literature studies on high-Cr FeCr alloys that were thermally aged at 500°C. The observed results suggest that Generation II FeCrAl alloys retain ductility under low-dose, prototypical LWR irradiation conditions.

36 MATERIALS SCIENCE↗

Real Time Degassing of Rock during Deformation

An experimental system we developed combines triaxial rock deformation and mass spectrometry to measure noble gas flow before, during, and after rock fracture. Geogenic noble gas is released during triaxial deformation (real time) and is related to volume strain and acoustic emissions. The noble gas release then represents a signal of deformation during its stages of development. Noble gases are contained in most crustal rock at inter and intra granular sites. Their release during natural and man-made stress and strain changes represents a signal of deformation in brittle and semi-brittle conditions. The noble gas composition depends on lithology, geologic history, age of the rock, and fluids present. Uranium, thorium and potassium-40 concentrations in the rocks also affect the production of radiogenic noble gases (4He, Ar). Noble gas emission and its relationship to crustal processes have been studied for many years in the geologic community including correlations to tectonic velocities and qualitative estimates of deep permeability from surface measurements, finger prints of nuclear weapon detonation, and as a potential precursory signal to earthquakes attributed to gas release due to pre-seismic stress, dilatancy and/or fracturing of the rock. Helium emission has been shown as a precursor of volcanic activity. We present empirical results/relationships of specimen strain, microstructural evolution, acoustic emissions, and noble gas release from laboratory triaxial experiments performed upon a granite and a young basalt, bedded salt, and a marine shale.

58 GEOSCIENCES↗

Mechanical Properties and Deformation Behavior of Additively Manufactured 316L Stainless Steel (FY2020)

The Transformational Challenge Reactor (TCR) program plans to build most of the TCR core components through additive manufacturing (AM) processes. These processes include laser powder bed fusion (LPBF) for the metallic (316L) components and the newly developed combined process of binderjet printing and chemical vapor infiltration (CVI) for the SiC fuel matrix. Mechanical testing and characterization tasks have been carried out since the beginning of the TCR program to (1) build a property database for the AM materials that will be used in TCR core and (2) to assess the materials’ performance in TCR-relevant conditions. This document reports the outcome of the testing and characterization efforts for the fiscal year with a focus on the mechanical performance data of AM 316L stainless steel (SS). Baseline tensile testing over a wide temperature range of room temperature–600 °C was completed for the AM 316L alloy in as-built, stress-relieved, and solution-annealed conditions. The as-built 316L showed the highest strength, and the alloy after the post-build treatments showed reduced strengths in the low-strain range. However, the strength differences among the AM materials became insignificant in the later part of deformation. Furthermore, regardless of post-build processing, the AM 316L SS showed higher strength and comparable ductility when compared with wrought 316L SS. Thermal creep testing and microstructural evolution during creep deformation were also performed under selected conditions. It was found that the AM 316L steel showed the best creep resistance in the stress-relieved condition. In-situ tensile tests were performed using scanning electron microscopy and 1-ID beamline at the Advanced Photon Source to elucidate the deformation and fracture behavior of AM 316L and the evolution of crystalline stress, dislocations, and pore distribution. Using these in-situ testing data, an in-depth analysis of the roles of microstructural features in deformation and fracture processes is presented herein. The final section of the document introduces ongoing and future activities for materials testing and characterization, including irradiation effect studies and ball punch testing on AM 316L and AM IN718 alloys.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Status of Mock-up and Integration for Ultrasonic Deformation Sensor for TREAT Experiments

Fuel deformation (both axial and radial) information provides insights into fuel performance and failure limits. Traditionally, fuel deformation has been quantified using post-irradiation examinations due to the lack of an appropriate sensor for monitoring deformation in situ. Recent developments in sensor and instrumentation design have led to the use of linear variable differential transducers (LVDT) for monitoring axial strain in fuel during irradiation. Size and operational constraints limit the use of LVDT sensors for radial deformation monitoring, and alternatives are needed. One possible alternative to LVDT sensors is an ultrasonic sensor. Ultrasonic sensors monitor the interaction of high-frequency stress waves with the test object. The resulting response may be analyzed to determine the properties of the material, including stress, strain, microstructure, presence of defects, and the elastic constants. While ultrasonic measurements have been successfully applied for monitoring strain in a number of applications, their use for in-core measurements has been limited. Largely, the limitations are due to the challenges associated with designing sensors that can operate under typical in-core conditions. This report documents progress to date toward planning, construction, and testing of a mock-up test capsule/facility to be used for in-lab testing of ultrasonic displacement sensor designs and toward integration of the sensor into prototypic TREAT experiment designs.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

High-Silicon Steel Strip by Single-Step Shear Deformation Processing

It is well known that Fe-Si alloys with Si content higher than in conventional electrical sheet steels (>3.2% Si) can make a significant impact in improving the efficiency of electrical motors if they are available in sheet/foil (strip) forms at suitable cost. While the magnetic and electrical attributes (e.g., resistivity, core loss) of these high-Si Fe alloys, of relevance to electrical motor core laminations, are known to be exceptional, the alloys have limited workability, making them difficult to produce consistently in sheet/foil (strip) forms. Current processing techniques such as rolling, while adequate for producing conventional electrical steel sheet, do have important disadvantages - large energy consumption and emissions, limitations in processing of low-workability alloys (e.g., high-Si content steels), large-scale plant infrastructure, and less than adequate capability to engineer sheet metals with specific microstructures (e.g., fine-grained) and crystallographic textures (e.g., shear textures). It is therefore of interest to have an alternative commercial process that can produce sheet/foil (strip) from high-Si Fe alloys and which can also overcome some of the deficiencies of current multistage strip processes. The goal of the present project was design and demonstration of a new energy-efficient pilot process for producing high-Si electrical steel strip of commercial widths and thickness, and with superior electrical and magnetic properties than current electrical steels (Fe-3.2% Si as benchmark). The applications domain for these steels is electrical motor core laminations. We have addressed this goal by accomplishment of the following specific objectives and tasks: a) Development of an Fe-4Si-4Cr alloy with electrical resistivity >80 μΩ-cm, induction flux density >1.48 T at 5000 A/m and core loss 35% lower than the benchmark 3.2% Si alloy. The alloy which meets DOE target specifications for motor core attributes was designed with the Si content controlled for the electrical properties and the Cr content tailored to meet material/process workability requirements. b) A unique machining-based deformation processing system was designed and scaled-up to produce strip of commercial width (25 mm to 150 mm) and thickness (up to 0.5 mm) from the Fe-4Si-4Cr alloy and other alloys of varied workability including copper, Al6061-T6 and naval brass. The key attributes of the machining-based strip production are deformation processing by concentrated simple-shear; single-step production of strip from ingot using compact machine infrastructure; strip surface finish of Ra 0.35 to 1 micrometer that is comparable/superior to that of rolled strip; discrete production of strip that can potentially be done at point of use; and controllability of strip mechanical/formability properties by deformation control. c) The electrical, magnetic, surface quality, mechanical, formability, and metallurgical properties/attributes of the machining-based strip were established by direct ASTM standard or equivalent measurement techniques. d) Punching characteristics of the strip in terms of load, edge quality and macro defects were similar to those of conventional 3.2% Si electrical steels. These punching characteristics are critical from a manufacturability perspective for motor/transformer core applications. e) A modeling framework for energy analysis of multistage rolling and the machining-based deformation processing has been established. Application of this modeling to the two strip-processes showed that the machining-based process requires significantly lower specific energy for processing, ~ 25% of that for rolling. The modeling framework can be adapted for a range of sheet-metal forming, bulk metal forming, and machining processes. It can be used to identify key parameters controlling process specific energy. f) A comparative analysis of advantages and disadvantages of machining-based processing against rolling for strip production. The single stage machining-based processing, with compact infrastructure, represents a new manufacturing paradigm for sheet and foil manufacturing that can potentially also be applied to advanced titanium, aluminum, copper and magnesium alloys. The goals and objectives were accomplished by a cross-disciplinary project team comprising of personnel from Purdue University; M4 Sciences LLC, a small-business focused on advanced manufacturing technology development; the Pacific Northwest National Labs; and tool manufacturers. The team is currently in advanced discussions with multiple entities for future process development for commercialization.

36 MATERIALS SCIENCE↗

Thermoelectric Temperature Measurement of Deforming Solids

Sold phase processing (SPP) utilizes large deformations and elevated but sub-melting temperatures to process materials in an energy-efficient manner to achieve high-performance properties. Studying the fundamental material science and kinetics requires an accurate temperature history of the process, but accurately measuring temperature at the point of deformation is very difficult. This study uses the thermoelectric principle to allow for the direct measurement of a deforming surface by turning the workpieces themselves into the measurement device. By so doing, results measured temperatures are closer to the actual deforming interface, more accurate, more responsive, and more reliable than corresponding measurements taken with standard thermocouples.

36 MATERIALS SCIENCE↗

Coupling between collective modes in the deformed 98 Zr nucleus: Insights from consistent HFB+QRPA calculations with the Gogny interaction

The Zirconium isotopes exhibit structural properties that present multiple challenges to nuclear theory. Investigations of the coupling present within isoscalar modes and within isovector modes are scarce but important for advancing our understanding of the microscopic picture of nuclei. To explore some of these underlying coupling features, and to test the predictive power of a state-of the-art nuclear structure approach, we provide a detailed analysis of the properties of 90,96,98Zr. This region includes a benchmarking case and offers insights into nuclear deformation phenomena. To investigate the coupling between collective modes in deformed nuclei, we focused our analysis on the ground and excited-state properties of these isotopes, employing a consistent approach with the axially-symmetric deformed Hartree-Fock-Bogoliubov (HFB) and the Quasiparticle Random Phase Approximation (QRPA) framework, both using the Gogny D1M force. This approach effectively describes both low-lying and giant-resonance states. We devoted special attention to the deformed 98Zr nucleus, where we confirm the existence of coupling between monopole and quadrupole excitations through the K π = 0 + QRPA components and demonstrate an analogous dipole-octupole coupling through the K π = 0 − and K π = 1 − components. Intrinsic transition densities and associ ated radial projections illustrate the coupling. Our work complements and extends earlier studies carried out using density-functional-based methods and notably, we included the complete Coulomb interaction also in the pairing fields, i.e. we treat terms exactly that are approximated in typical calculations that use the Gogny D1 and D2 interaction families.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗