Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attribute measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Curing of epoxy resins with 1-DI(2-chloroethoxyphosphinyl) methyl-2,4 and -2,6-diaminobenzene

Fire resistant compositions were prepared using 1-di(2-chloroethoxy-phosphinyl)methyl-2,4- and -2,6-diaminobenzene (DCEPD) as a curing agent for typical epoxy resins such as EPON 828 (Shell), XD 7342 (Dow), and My 720 (Ciba Geigy). In addition, compositions of these three epoxy resins with common curing agents such as m-phenylenediamine (MPD) or 4,4'-diaminodiphenylsulphone (DDS) were studied to compare their reactions with those of DCEPD. The reactivity of the three curing agents toward the epoxy resins, measured by differential calorimetry (DSC), was of the order MPD DCEPD DDS. The relatively lower reactivity of DCEPD toward epoxy resins was attributed to electronic effects.

Mikroyannidis, J. A.↗
NASA NTRS1984

Curing of epoxy resins with 1-/di(2-chloroethoxyphosphinyl)methyl/-2,4- and -2,6-diaminobenzene

Fire resistant compositions were prepared using 1-di(2-chloroethoxy-phosphinyl)methyl-2,4- and -2,6-diaminobenzene (DCEPD) as a curing agent for typical epoxy resins such as EPON 828 (Shell), XD 7342 (Dow), and My 720 (Ciba Geigy). In addition, compositions of these three epoxy resins with common curing agents such as m-phenylenediamine (MPD) or 4,4'-diaminodiphenylsulphone (DDS) were studied to compare their reactions with those of DCEPD. The reactivity of the three curing agents toward the epoxy resins, measured by differential calorimetry (DSC), was of the order MPD DCEPD DDS. The relatively lower reactivity of DCEPD toward epoxy resins was attributed to electronic effects.

Mikroyannidis, J. A.↗
NASA NTRS1986

Ozone and nitrogen dioxide changes in the stratosphere during 1979-84

Analyses of stratospheric nitrogen dioxide distributions as measured by four different satellite experiments indicate midlatitude increases of up to 75 percent during the 1979-84 period. These increases are attributed to enhanced upper atmospheric formation of odd nitrogen during solar cycle 21 with downward transport to the stratosphere. The increases in NO2 provide an explanation for the recently observed dramatic springtime minima in the Antarctic ozone and suggest the reason for the reported midlatitude stratospheric ozone decreases observed by satellite and ground-based stations since the mid 1970s.

Callis, Linwood B.↗
NASA NTRS1996

GOME Calibration and Validation Using Backscatter UV Techniques

GOME radiance, irradiance, and ozone products were validated by NASA Goddard Space Flight Center through three tasks which included, pre-launch calibration comparisons with SBUV and TOMS radiometric standards, validation of GOME Level-1 irradiance and radiance and Level 2 total ozone data products using SBUV/2 and TOMS algorithms and data, and studies of GOME data using the Goddard radiative transfer code. The prelaunch calibration using the NASA large aperture integrating sphere was checked against that provided by TPD. Agreement in the calibration constants, derived in air, between the Goddard and TPD system were better than 3%. Validation of Level-1 irradiance data included comparison of GOME and SSBUV and the UARS solar irradiances measurements. Large wavelength dependent differences, as high as 10%, were noted between GOME and the US instruments. This discrepancy has now been attributed to radiometric sensitivity changes experienced by GOME when operating in a vacuum. GOME Earth radiance data were then compared to the NOAA-14 SBUV/2 radiances. These results show that between 340 and 400 nm the differences in GOME and SBUV/2 data are less than 5% with some wavelength dependence. At wavelengths shorter than 300 nm, differences are of the order of 10% or more where the GOME radiances are larger. To test GOME DOAS retrieved total ozone values, these values were compared with ozone amounts retrieved using GOME radiances in the TOMS version-7 algorithm. The differences showed a solar zenith angle dependence ranging from 0 to 10% where the TOMS algorithm values were higher. GOME radiances below 300 nm were further validated by selecting radiances at wavelengths normally used by SBUV and processing them through the SBUV ozone profile algorithm and then compared to climatological values. The GOME ozone profiles ranged from 10-30% lower over altitude compared to climatological values. This is consistent with the offsets detected in the SBUV/2 radiance comparisons at wavelengths shorter than 300 nm.

Hilsenrath, E.↗
NASA NTRS1994

Remote Sensing of Seasonal Leaf Area Index Across the Oregon Transect

Remotely sensed data acquired from four remote-sensing instruments on three different aircraft platforms over a transect of coniferous forest stands in Oregon were analyzed with respect to seasonal leaf area index (LAI). Data from the four instruments were corrected for the varying seasonal and geographic atmospheric conditions present along the transect. Strong logarithmic relationships were observed between seasonal maximum and minimum LAI and the simple ratio (SR) (near infrared/red reflectance) calculated from the broad-spectral-band Thematic Mapper Simulator (TMS), as well as from the narrow-spectral-band Airborne Visible/Infrared Imaging Spectrometer (AVIRIS), the Compact Airborne Spectrographic Imager (CASI), and a Spectron SE590 spectro-radiometer (R(exp 2) = 0.82-0.97). The TMS SR reached an asymptote at an LAI of approx. 7-8. However, the SE590 and the CASI SR continued to increase up to the maximum LAI of 10.6. The variability of the relationship between the AVIRIS SR and LAI increased at stands with LAIs greater than 7, making a trend in the AVIRIS SR-LAI relationship at LAIs greater than 7 difficult to discern. The SRs of the coniferous forest stands measured by the narrow-spectral-band instruments were higher than they were from the broad-spectral-band TMS. This is attributed partially to the integration of the TMS over a broad wavelength region in the red and more strongly to calibration differences between the sensors. Seasonal TMS SR trends for four time periods for some of the stands deviated from the expected seasonal LAI trends, possibly because of smoke and very low sun angles during some of the acquisition periods. However, the expected SR differences for the seasonal minimum and maximum LAI were observed for all of the sensors for nearly all of the forest stands. This study, demonstrates that remotely, sensed data from both broad- and narrow spectral band instruments can provide estimates of LAI for use in forest ecosystems simulation models to estimate evapotranspiration, photosynthesis, canopy turnover, and net primary production over large areas.

Spanner, Michael↗
NASA NTRS1997

Absorption of Sunlight by Water Vapor in Cloudy Conditions: A Partial Explanation for the Cloud Absorption Anomaly

The atmospheric radiative transfer algorithms used in most global general circulation models underestimate the globally-averaged solar energy absorbed by cloudy atmospheres by up to 25 W/sq m. The origin of this anomalous absorption is not yet known, but it has been attributed to a variety of sources including oversimplified or missing physical processes in these models, uncertainties in the input data, and even measurement errors. Here, a sophisticated atmospheric radiative transfer model was used to provide a more comprehensive description of the physical processes that contribute to the absorption of solar radiation by the Earth's atmosphere. We found that the amount of sunlight absorbed by a cloudy atmosphere is inversely proportional to the solar zenith angle and the cloud top height, and directly proportional to the cloud optical depth and the water vapor concentration within the clouds. Atmospheres with saturated, optically-thick, low clouds absorbed about 12 W/sq m more than clear atmospheres. This accounts for about 1/2 to 1/3 of the anomalous ab- sorption. Atmospheres with optically thick middle and high clouds usually absorb less than clear atmospheres. Because water vapor is concentrated within and below the cloud tops, this absorber is most effective at small solar zenith angles. An additional absorber that is distributed at or above the cloud tops is needed to produce the amplitude and zenith angle dependence of the observed anomalous absorption.

Crisp, D.↗
NASA NTRS2001

Modeled Seasonal Variations of Firn Density Induced by Steady State Surface Air Temperature Cycle

Seasonal variations of firn density in ice-sheet firn layers have been attributed to variations in deposition processes or other processes within the upper firn. A recent high-resolution (mm scale) density profile, measured along a 181 m core from Antarctica, showed small-scale density variations with a clear seasonal cycle that apparently was not-related to seasonal variations in deposition or known near-surface processes (Gerland and others 1999). A recent model of surface elevation changes (Zwally and Li, submitted) produced a seasonal variation in firn densification, and explained the seasonal surface elevation changes observed by satellite radar altimeters. In this study, we apply our 1-D time-dependent numerical model of firn densification that includes a temperature-dependent formulation of firn densification based on laboratory measurements of grain growth. The model is driven by a steady-state seasonal surface temperature and a constant accumulation rate appropriate for the measured Antarctic ice core. The modeled seasonal variations in firn density show that the layers of snow deposited during spring to mid-summer with the highest temperature history compress to the highest density, and the layers deposited during later summer to autumn with the lowest temperature history compress to the lowest density. The initial amplitude of the seasonal difference of about 0.13 reduces to about 0.09 in five years and asymptotically to 0.92 at depth, which is consistent with the core measurements.

Jun, Li↗
NASA NTRS2006

Anomalous Shocks on the Measured Near-Field Pressure Signatures of Low-Boom Wind-Tunnel Models

Unexpected shocks on wind-tunnel-measured pressure signatures prompted questions about design methods, pressure signature measurement techniques, and the quality of measurements in the flow fields near lifting models. Some of these unexpected shocks were the result of component integration methods. Others were attributed to the three-dimension nature of the flow around a lifting model, to inaccuracies in the prediction of the area-ruled lift, or to wing-tip stall effects. This report discusses the low-boom model wind-tunnel data where these unexpected shocks were initially observed, the physics of the lifting wing/body model's flow field, the wind-tunnel data used to evaluate the applicability of methods for calculating equivalent areas due to lift, the performance of lift prediction codes, and tip stall effects so that the cause of these shocks could be determined.

Mack, Robert J.↗
NASA NTRS2012

Air Density Measurements in a Mach 10 Wake Using Iodine Cordes Bands

An exploratory study designed to examine the viability of making air density measurements in a Mach 10 flow using laser-induced fluorescence of the iodine Cordes bands is presented. Experiments are performed in the NASA Langley Research Center 31 in. Mach 10 air wind tunnel in the hypersonic near wake of a multipurpose crew vehicle model. To introduce iodine into the wake, a 0.5% iodine/nitrogen mixture is seeded using a pressure tap at the rear of the model. Air density was measured at 56 points along a 7 mm line and three stagnation pressures of 6.21, 8.62, and 10.0 MPa (900, 1250, and 1450 psi). Average results over time and space show rho(sub wake)/rho(sub freestream) of 0.145 plus or minus 0.010, independent of freestream air density. Average off-body results over time and space agree to better than 7.5% with computed densities from onbody pressure measurements. Densities measured during a single 60 s run at 10.0 MPa are time-dependent and steadily decrease by 15%. This decrease is attributed to model forebody heating by the flow.

Balla, Robert J.↗
NASA NTRS2020

Loads Correlation of a Full-Scale Proprotor on the Tiltrotor Test Rig

In 2018, a full-scale isolated proprotor test was conducted in the USAF National Full-Scale Aerodynamics Complex (NFAC) at NASA Ames. The test article was the 3-bladed Bell 699 research rotor derived from the AW609 rotor. For this test, the NASA Tiltrotor Test Rig (TTR) and rotor were installed in the 40- by 80-foot test section. Correlations between the 2018 test data and predictions from the comprehensive analysis CAMRAD II for blade and yoke (flexbeam) loads and rotor torque are presented. The full range of conversion to helicopter modes is covered: conversion 30-, 45-, and 60-deg TTR yaw, and helicopter 75- and 90-deg TTR yaw. The flap moment correlation is reasonable to good; the pitch link load and torsion moment are uniformly underpredicted. The measured 2P lag moment and 2P torque are not captured by the analysis. The inability to predict the 2P component is currently attributed to the analytical assumption of a perfect gimbal, whereas the actual test gimbal may be operating imperfectly and thus introducing the 2P harmonic. A new analytical model that accounts for non-ideal gimbal operation is needed.

Kottapalli, Sesi↗
NASA NTRS1975

Dynamic characteristics of a 30-centimeter mercury ion thruster

The present work reports on measurements of the fluctuations in the beam current, discharge current, neutralizer keeper current, and discharge voltage of a 30-cm ion thruster made with 60Hz laboratory-type power supplies. The intensities of the fluctuations (ratio of the root-mean-square magnitude to time-average quantity) were found to depend significantly on the beam and magnetic baffle currents. The shape of the frequency spectra of the discharge plasma fluctuations was related to the beam and magnetic baffle currents. The predominant peaks of the beam and discharge current spectra occurred at frequencies less than 30 kilohertz. This discharge chamber resonance could be attributable to ion-acoustic wave phenomena. Cross-correlations of the discharge and beam currents indicated that the dependence on the magnetic baffle current was strong. The measurements revealed that the discharge current fluctuations directly contribute to the beam current fluctuations and that the power supply characteristics can modify these fluctuations.

Serafini, J. S.↗
DOE OSTI2023

Identifying the secondary electron cutoff in ultraviolet photoemission spectra for work function measurements of non-ideal surfaces

Abstract Absolute values of work functions can be determined in ultraviolet photoemission spectroscopy (UPS) by measuring the minimum kinetic energy of secondary electrons generated by a known photon energy. However, some samples can produce spectra that are difficult to interpret due to additional intensity below the true secondary electron cutoff. Disordered absorbates on elemental metals add small intensity below the onset for the transition metal surfaces studied, which can be attributed to energy losses after photoelectrons are generated. In contrast, spectra from WO 3−x films can produce multiple onsets with comparable intensity which do not fit this model. False onsets (in the context of work function measurements) can be minimized by optimizing experimental detection parameters including limiting analyzer acceptance angles and pass energy. True work functions can be identified by examining the onsets as the sample bias is varied.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1991

Extracting fuzzy rules under uncertainty and measuring definability using rough sets

Although computers have come a long way since their invention, they are basically able to handle only crisp values at the hardware level. Unfortunately, the world we live in consists of problems which fail to fall into this category, i.e., uncertainty is all too common. A problem is looked at which involves uncertainty. To be specific, attributes are dealt with which are fuzzy sets. Under this condition, knowledge is acquired by looking at examples. In each example, a condition as well as a decision is made available. Based on the examples given, two sets of rules are extracted, certain and possible. Furthermore, measures are constructed of how much these rules are believed in, and finally, the decisions are defined as a function of the terms used in the conditions.

Culas, Donald E.↗
DOE OSTI2020

Femtosecond electronic structure response to high intensity XFEL pulses probed by iron X-ray emission spectroscopy

We report the time-resolved femtosecond evolution of the K-shell X-ray emission spectra of iron during high intensity illumination of X-rays in a micron-sized focused hard X-ray free electron laser (XFEL) beam. Detailed pulse length dependent measurements revealed that rapid spectral energy shift and broadening started within the first 10 fs of the X-ray illumination at intensity levels between 10 17 and 10 18 W cm -2 . We attribute these spectral changes to the rapid evolution of high-density photoelectron mediated secondary collisional ionization processes upon the absorption of the incident XFEL radiation. These fast electronic processes, occurring at timescales well within the typical XFEL pulse durations (i.e., tens of fs), set the boundary conditions of the pulse intensity and sample parameters where the widely-accepted ‘probe-before-destroy’ measurement strategy can be adopted for electronic-structure related XFEL experiments.

99 GENERAL AND MISCELLANEOUS↗
NASA NTRS2021

The benefit of brightness temperature assimilation for the SMAP Level-4 surface and root-zone soil moisture analysis

The Soil Moisture Active Passive (SMAP) Level-4 (L4) product provides global estimates of surface soil moisture (SSM) and root-zone soil moisture (RZSM) via the assimilation of SMAP brightness temperature (Tb) observations into the NASA Catchment Land Surface Model (CLSM). Here, using in situ measurements from 2474 sites in China, we evaluate the performance of soil moisture estimates from the L4 data assimilation (DA) system and from a baseline “open-loop” (OL) simulation of CLSM without Tb assimilation. Using random forest regression, the efficiency of the L4 DA system (i.e., the performance improvement in DA relative to OL) is attributed to eight control factors related to the CLSM as well as τ–ω radiative transfer model (RTM) components of the L4 system. Results show that the Spearman rank correlation (R) for L4 SSM with in situ measurements increases for 77 % of the in situ measurement locations (relative to that of OL), with an average R increase of approximately 14 % (ΔR=0.056). RZSM skill is improved for about 74 % of the in situ measurement locations, but the average R increase for RZSM is only 7 % (ΔR=0.034). Results further show that the SSM DA skill improvement is most strongly related to the difference between the RTM-simulated Tb and the SMAP Tb observation, followed by the error in precipitation forcing data and estimated microwave soil roughness parameter h. For the RZSM DA skill improvement, these three dominant control factors remain the same, although the importance of soil roughness exceeds that of the Tb simulation error, as the soil roughness strongly affects the ingestion of DA increments and further propagation to the subsurface. For the skill of the L4 and OL estimates themselves, the top two control factors are the precipitation error and the SSM–RZSM coupling strength error, both of which are related to the CLSM component of the L4 system. Finally, we find that the L4 system can effectively filter out errors in precipitation. Therefore, future development of the L4 system should focus on improving the characterization of the SSM–RZSM coupling strength.

Jianxiu Qiu↗
DOE OSTI2023

Anomalous magnetothermoelectric behavior in massive Dirac materials

Extensive studies of electron transport in Dirac materials have shown positive magnetoresistance (MR) and positive magnetothermopower (MTP) in a magnetic field perpendicular to the excitation current or thermal gradient. In contrast, measurements of electron transport often show a negative longitudinal MR and negative MTP for a magnetic field oriented along the excitation current or thermal gradient; this is attributed to the chiral anomaly in Dirac materials. In this paper, we report a very different magnetothermoelectric transport behavior in the massive Dirac material ZrTe5. Although thin flakes show a commonly observed positive MR in a perpendicular magnetic field, distinct from other Dirac materials, we observe a sharp negative MTP. In a parallel magnetic field, we still observe a negative longitudinal MR, however, a remarkable positive MTP is observed for the fields parallel to the thermal gradients. Our theoretical calculations suggest that this anomalous magnetothermoelectric behavior can be attributed to the screened Coulomb scattering. This work demonstrates the significance of impurity scattering in the electron transport of topological materials and provides deep insight into the magnetotransport phenomena in Dirac materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Improving cellulose attribution by selectively removing yeast glucans from grain fermentation intermediates

Abstract This article presents an industry-relevant method for quantifying cellulose in mixed substrate samples. We built upon the cellulosic glucan measurement proposed by Sluiter et al. (2021) to investigate significant cellulose loss under cold caustic conditions, which has hindered the establishment of an industrially relevant method. To overcome this issue, we used dimethyl sulfoxide (DMSO) as an alternative solvent, which avoids mercerization reactions (Budtova and Navard 2015) but may leave some resistant starch in the sample. Treatment via an enzyme mixture removed starch and conformed to US Environmental Protection Agency (EPA) guidance on cellulose measurement by establishing quantitative de-starching via nuclear magnetic resonance (EPA 2022). The selective removal of yeast beta-glucan was accomplished using a commercially available Zymolyase. Our results demonstrated excellent reproducibility, with coefficients of variance of 7.14% or less, when measuring cellulose in low cellulose content samples. The method was tested on relevant lab and plant samples, showing an average 0.9% ethanol derived from the conversion of cellulose when cellulase was added to the process and zero response when no cellulase was added. These findings indicate that a cellulose method using DMSO and pullulanase provides a complete and accurate view of cellulose content, composition, and conversion in industrial fermentation processes.

Sluiter, Justin [National Renewable Energy Laborat↗
NASA NTRS1980

Measuring the development process: A tool for software design evaluation

The design metrics evaluator (DME), a component of an automated software design analysis system, is described. The DME quantitatively evaluates software design attributes. Its use directs attention to areas of a procedure, module, or complete program having a high potential for error.

Moy, S. S.↗