Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “airfoil”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Some calculations of transonic potential flow for the NACA 64A006 airfoil with oscillating flap

A method for calculating the transonic flow over steady and oscillating airfoils was developed by Isogai. It solves the full potential equation with a semi-implicit, time-marching, finite difference technique. Steady flow solutions are obtained from time asymptotic solutions for a steady airfoil. Corresponding oscillatory solutions are obtained by initiating an oscillation and marching in time for several cycles until a converged periodic solution is achieved. In this paper the method is described in general terms, and results are compared with experimental data for both steady flow and for oscillations at several values of reduced frequency. Good agreement for static pressures is shown for subcritical speeds, with increasing deviation as Mach number is increased into the supercritical speed range. Fair agreement with experiment was obtained at high reduced frequencies with larger deviations at low reduced frequencies.

Bennett, R. M.↗
NASA NTRS1978

Observations on the dynamic stall characteristics of advanced helicopter rotor airfoils

A significant amount of research was devoted to understanding the mechanism of dynamic stall delay as applicable to the flow environment of a helicopter rotor in forward flight. One aspect of such research deals with the unsteady characteristics of two-dimensional airfoil sections over a Mach number range from 0.3 to 9.6, since such characteristics can be meaningfully related to rotor performance and loads. This paper summarizes the results of several oscillatory tests carried out on conventional, transonic and BLC-equipped airfoils.

Dadone, L.↗
NASA NTRS1979

Transonic airfoil codes

Computer codes for the design and analysis of transonic airfoils are considered. The design code relies on the method of complex characteristics in the hodograph plane to construct shockless airfoil. The analysis code uses artificial viscosity to calculate flows with weak shock waves at off-design conditions. Comparisons with experiments show that an excellent simulation of two dimensional wind tunnel tests is obtained. The codes have been widely adopted by the aircraft industry as a tool for the development of supercritical wing technology.

Garabedian, P. R.↗
NASA NTRS1979

A consistent design procedure for supercritical airfoils in free air and a wind tunnel

A computational inverse procedure for transonic airfoils in which shapes are determined supporting prescribed pressure distributions is presented. The method uses the small disturbance equation and a consistent analysis-design differencing procedure at the airfoil surface. This avoids the intermediate analysis-design-analysis iterations. The effect of any openness at the trailing edge is taken onto account by adding an effective source term in the far field. The final results from a systematic expansion procedure which models the far field for solid, ideal slotted, and free jet tunnel walls are presented along with some design results for the associated boundary conditions and those for a free flight.

Shankar, V.↗
NASA NTRS1979

An evaluation of four single element airfoil analytic methods

A comparison of four computer codes for the analysis of two-dimensional single element airfoil sections is presented for three classes of section geometries. Two of the computer codes utilize vortex singularities methods to obtain the potential flow solution. The other two codes solve the full inviscid potential flow equation using finite differencing techniques, allowing results to be obtained for transonic flow about an airfoil including weak shocks. Each program incorporates boundary layer routines for computing the boundary layer displacement thickness and boundary layer effects on aerodynamic coefficients. Computational results are given for a symmetrical section represented by an NACA 0012 profile, a conventional section illustrated by an NACA 65A413 profile, and a supercritical type section for general aviation applications typified by a NASA LS(1)-0413 section. The four codes are compared and contrasted in the areas of method of approach, range of applicability, agreement among each other and with experiment, individual advantages and disadvantages, computer run times and memory requirements, and operational idiosyncrasies.

Freuler, R. J.↗
NASA NTRS1979

Design and calibration of slotted walls for transonic airfoil wind tunnels

The traditional procedure for estimating the performance of slotted walls for airfoil wind tunnels is reviewed, and a modification which improves the accuracy of this procedure is described. Unlike the traditional procedure, the modified procedure indicates that the design of airfoil wind-tunnel walls which induce minimal blockage and streamline-curvature effects is feasible. The design and testing of such a slotted wall is described. It is shown experimentally that the presence of a model can affect the plenum pressure and thus make the use of the plenum pressure as a calibration reference questionable. Finally, an ONERA experiment which shows the effect of the sidewall boundary layer on the measured model normal force is discussed.

Barnwell, R. W.↗
NASA NTRS1979

Computation of turbulent near wake for asymmetric airfoils

A numerical procedure for studying the turbulent near wake of two dimensional airfoil sections is presented. The Reynolds Navier-Stokes equations were written for flow about bodies of arbitrary geometry and solved on an arbitrary nonuniform curvilinear computational mesh. Eddy viscosity and Reynolds stress turbulence transport models are considered. Specific examples are shown for airfoil section by using an algebraic viscosity model with streamwise relaxation and the interactive Reynolds stress model.

Deiwert, G. S.↗
NASA NTRS1979

Structure of the Turbulent Separated Flow Around a Stalled Airfoil

Hot-wire measurements were made in the boundary layer, the separated region, and the near wake for flow past a NACA 4412 airfoil at maximum lift. The Reynolds number based on chord was 1,500,000. Special care was taken to achieve a two-dimensional mean flow. Data were obtained at several thousand locations in the flow field. These data include intermittency, two components of mean velocity, and mean values for three double, four triple, and five quadruple products of two velocity fluctuations. No information was obtained about the third (spanwise) velocity component. Smoothing and interpolating routines were used to determine intermittency, two components of mean velocity, and mean values of three double, four triple, and five quadruple products of two velocity fluctuations on a fine rectangular mesh aligned with the airfoil chord. The data are presented in contour plots, in three-dimensional plots, and in tabular form. The format used to store the experimental data in digital form is described and a computer program which illustrates how this data can be accessed is presented.

Wadcock, A. J.↗
NASA NTRS1979

An Exploratory Investigation of the Effect of Plastic Coating on the Profile Drag of a Practical-Metal-Construction Sailplane Airfoil

An exploratory investigation was performed in the Langley low-turbulence pressure tunnel to determine the effect of a plastic coating on the profile drage of a practical-metal-construction sailplaine airfoil. The mode was tested with three surface configurations: (1) filled, painted, and sanded smooth; (2) rough bare metal; and (3) plastic-coated. The investigation was conducted at Reynolds numbers based on airfoil chord of 1,100,000, 2,200,000, and 3,300,000 at a constant Mach number of 0.10. The results indicate that, at all three Reynolds numbers, the order of the drag values of the three surface configurations, starting with the highest drag, was: filled, painted, and sanded smooth; rough bare metal; and plastic-coated.

Somers, D. M.↗
NASA NTRS1977

Low-speed wind tunnel results for a modified 13-percent-thick airfoil

Wind-tunnel tests were conducted to evaluate the effects on performance of modifying a 13-percent-thick low-speed airfoil. The airfoil contour was altered to reduce the aft upper surface pressure gradient and hence delay boundary layer separation at typical lift coefficients for light general aviation airplanes. The tests were conducted at a Mach number of 0.15 or less over a Reynolds number range from about 1,000,000 to 9,000,000.

Mcghee, R. J.↗
NASA NTRS1979

A study of the drooped leading edge airfoil

Wind tunnel tests were conducted to examine various aspects of the drooped-leading edge airfoil which reduces the tendency for an airplane to enter a spin after stall occurs. Three baseline models were used for tests of two dimensional models: NACA 0015, 0014.6, and 0014.2. The 14.6% and 14.2% models were derived from NACA 0015 sections by increasing the chord and matching the profiles aft section. Force, balance data (lift, drag, pitching moment) were obtained for each model at a free-steam Reynold's number of 2.66 x 10 to the 6th power/m. In addition, oil flow visualization tests were performed at various angles of attack. An existing NACA 64 sub 1 A211 airfoil was used in a second series of tests. The leading edge flap was segmented in three parts which allowed various baseline/drooped leading edge configurations to be tested. Force balance and flow visualization tests were completer at chord Renolds numbers of 0.44 x 10 to the 6th power, 1.4 x 10 to the 6th power, and 2.11 x 10 to the 6th power. Test results are included.

Anderson, J. D., Jr.↗
NASA NTRS1978

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

Mild steel (AISI 1018) was selected as model cold-rolling material and Ti-6Al-4V and INCONEL 718 were selected as typical hot-rolling and cold-rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape-rolling process were developed. These models utilize the upper-bound and the slab methods of analysis, and are capable of predicting the lateral spread, roll-separating force, roll torque and local stresses, strains and strain rates. This computer-aided design (CAD) system is also capable of simulating the actual rolling process and thereby designing roll-pass schedule in rolling of an airfoil or similar shape. The predictions from the CAD system were verified with respect to cold rolling of mild steel plates. The system is being applied to cold and hot isothermal rolling of an airfoil shape, and will be verified with respect to laboratory experiments under controlled conditions.

Lahoti, G. D.↗
NASA NTRS1979

Upper-surface modifications for C sub l max improvement of selected NASA 6-series airfoils

The thickness of the upper surface of 64 airfoils was increased from the leading edge to the position of maximum thickness. The modifications were generated using a numerical optimization routine coupled with an aerodynamic analysis code. The type of modification presented can be used for aircraft design or for the retrofit of current aircraft to improve the stall characteristics and climb performance. The coordinates of the modified airfoils are presented with plots of the forward 45% of the profiles and pressure distributions for both the modified and unmodified sections at an angle of attack of 14 degrees.

Szelazek, C. A.↗
NASA NTRS1978

Rotor-airfoil flight investigation - Preliminary results

A flight investigation has been conducted to study the behavior of three advanced-technology airfoils in the three-dimensional, unsteady-flow environment of the helicopter main rotor. Three sets of instrumented main-rotor blades were flown on an AH-1G helicopter. Each set employed one of three airfoils developed with significantly different design technologies. Data are given on performance, rotor loads, and the measurements of chordwise pressure distribution at 90 percent blade radius. The pressure data are compared with theoretical distributions calculated for two-dimensional, steady flow.

Morris, C. E. K., Jr.↗
NASA NTRS1979

Design of transonic airfoil sections using a similarity theory

In the present paper, it is shown that numerical optimization is a powerful tool for designing transonic wings and airfoils. Nixon's (1978) similarity theory is extended to cover design optimization problems. Some ground rules for designing shock-free airfoils are proposed and their application is demonstrated by examples. Advantages which accrue from integrating similarity theory into the numerical optimization procedure are noted.

Nixon, D.↗
NASA NTRS1979

An efficient algorithm for numerical airfoil optimization

A new optimization algorithm is presented. The method is based on sequential application of a second-order Taylor's series approximation to the airfoil characteristics. Compared to previous methods, design efficiency improvements of more than a factor of 2 are demonstrated. If multiple optimizations are performed, the efficiency improvements are more dramatic due to the ability of the technique to utilize existing data. The method is demonstrated by application to subsonic and transonic airfoil design but is a general optimization technique and is not limited to a particular application or aerodynamic analysis.

Vanderplaats, G. N.↗
NASA NTRS1979

Split-film anemometer measurements on an airfoil with turbulent separated flow

Experimental studies of turbulent separation on airfoils have been conducted to aid in improving theoretical models of post-stall airfoil behavior. The studies utilize a variety of pressure and hot-film probes. The split-film anemometer has proved particularly valuable for measurement of highly turbulent reversing flows. Suggested techniques for on-line digital computer processing of the data are discussed.

Wentz, W. H., Jr.↗
NASA NTRS1979

Transonic flow past a symmetrical airfoil at high angle of attack

The results of an experimental investigation of shock-induced stall and leading-edge stall on a 64A010 airfoil section are presented. Advanced nonintrusive techniques - laser velocimetry, holographic interferometry, and buried-wire anemometry - were used in characterizing the inviscid and viscous flow regions. The measurements include Mach contours of the inviscid flow regions, and mean velocity, flow direction and Reynolds shear stress profiles in the separated regions. The experimental observations of this study are relevant to efforts to improve surface pressure prediction methods for airfoils at or near stall.

Johnson, D. A.↗