SEARCH · Engineering Papers

Results for “WING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

All sources NASA NTRS DOE OSTI

NASA NTRS1987

Low-speed wind tunnel study of longitudinal stability and usable-lift improvement of a cranked wing

An exploratory low-speed investigation of a 70 deg/46 deg cranked-wing planform was undertaken to evaluate two vortex-control concepts aimed at alleviating a severe pitch up which limits the usable lift well below the C(sub L,max) of the basic wing. One concept was a strake-like extension introduced across the wing crank, whose vortex helps to stabilize the outer-wing flow and alleviate tip stall. The other was a lower-surface cavity flap employed to trap a vortex just beneath the inboard leading edge, resulting in reduced vortex lift over the inner-wing panel. Each of these concepts was shown to eliminate the high-alpha pitch up, potentially raising the maximum usable lift of the cranked wing practically to its C(sub L,max) value.

Rao, Dhanvada M.↗

NASA NTRS1987

Investigation of transonic region of high dynamic response encountered on an elastic supercritical wing

Unsteady aerodynamic data were measured on an aspect ratio 10.3 elastic supercritical wing while undergoing high dynamic response above a Mach number of 0.90. These tests were conducted in the NASA Langley Transonic Dynamics Tunnel. A previous test of this wing predicted an unusual instability boundary based on subcritical response data. During the present test no instability was found, but an angle of attack dependent narrow Mach number region of high dynamic wing response was observed over a wide range of dynamic pressures. The effect on dynamic wing response of wing angle of attack, static outbound control surface deflection and a lower surface spanwise fence located near the 60 percent local chordline was investigated. The driving mechanism of the dynamic wing response appears to be related to chordwise shock movement in conjunction with flow separation and reattachment on both the upper and lower surfaces.

Seidel, David A.↗

NASA NTRS1986

Arbitrary motion unsteady aerodynamics and its application to rotary-wing aeroelasticity

This paper presents in a unified manner recent research on arbitrary motion unsteady aerodynamics with an emphasis on applications to a number of rotary wing aeroelastic problems. The term arbitrary motion is used to denote growing or decaying oscillations with a certain frequency. The specific topics treated in this paper are: (1) generalization of Greenberg's theory and its application to hingeless rotor aeroelastic stability; (2) description of a new technique for formulating finite state approximations to steady aerodynamic theories, which are suitable for both fixed-wing and rotary-wing applications, and its application to generalize Loewy's theory; (3) comparison of fixed wing and rotary-wing indicial response functions; (4) influence of arbitrary motion aerodynamics, as represented by dynamic inflow on a helicopter in ground resonance. From the discussion of these topics a number of useful conclusions on the fundamental nature of arbitrary motion aerodynamics and its role in rotary-wing aeroelasticity are obtained.

Friedmann, P. P.↗

NASA NTRS1986

Low Aspect Ratio Wings at High Angles of Attack

A comprehensive evaluation is made of experimental data compiled to date for the flowfields and aerodynamic forces that occur at high angles of attack for low aspect ratio wings with delta, rectangular, clipped delta, and strake/wing planform geometries. Attention is given to wing leading edge-generated vortex breakdown, aspect ratio and compressibility effects, and strake vortex effects on main wing areas. Although the nonlinear effects created by a wing-body combination significantly alter wing-alone aerodynamics, the wing-alone data presented are vital to the development of prediction methodologies for large angle of attack aerodynamics.

R L Stallings Jr.↗

NASA NTRS1986

Installation aerodynamics of wing-mounted, single-rotation propfans

The installation of advanced (M = 0.8) turboprop propulsion systems on transport aircraft represents a challenging task to design engineers. The installation aerodynamics of wing-mounted, single-rotation, tractor turboprop systems have been extensively investigated by NASA Ames using a large powered semispan wind tunnel model. Two configurations have been studied: a straight under-the-wing (UTW) nacelle and a contoured over-the-wing (OTW) configuration. The installation characteristics of these two configurations are presented in terms of installed drag, wing pressure distributions, and surface oil flows. Through the use of wing leading-edge modifications, the installed drag of the UTW nacelle was reduced to less than isolated nacelle drag at the cruise condition of M = 0.8 with a wing C(L) of 0.5. At this condition, the favorable interference is attributed to the recovery of a portion of the swirl in the slipstream generated by the single rotation propeller. The OTW installation represented a much more difficult task. For the configuration tested, the installed drag was unacceptably high and demonstrated the sensitive nature of installing a nacelle/slipstream combination in the transonic flow regime.

Bencze, Daniel P.↗

NASA NTRS1987

Investigation of transonic region of high dynamic response encountered on an elastic supercritical wing

Unsteady aerodynamic data were measured on an aspect ratio 10.3 elastic supercritical wing while undergoing high dynamic response above Mach number of 0.90. These tests were conducted in the NASA Langley Transonic Dynamics Tunnel. A previous test of this wing predicted an unusual instability boundary based upon subcritical response data. During the present test no instability was found, but an angle of attack dependent narrow Mach number region of high dynamic wing response was observed over a wide range of dynamic pressures. The effect on dynamic wing response of wing angle of attack, static outboard control surface deflection and a lower surface spanwise fence located near the 60 percent local chordline was investigated. The driving mechanism of the dynamic wing response appears to be related to chordwise shock movement in conjunction with flow separation and reattachment on both the upper and lower surfaces.

Seidel, David A.↗

NASA NTRS1987

Flutter study of an advanced composite wing with external stores

A flutter test using a scaled model of an advanced composite wing for a Navy attack aircraft has been conducted in the NASA Langley Research Center Transonic Dynamics Tunnel. The model was a wall-mounted half-span wing with a semi-span of 6.63 ft. The wing had an aspect ratio of 5.31, taper ratio of 0.312, and quarter-chord sweep of 25 degrees. The model was supported in a manner that simulated the load path in the carry-through structure of the aircraft and the symmetric boundary condition at the fuselage centerline. The model was capable of carrying external stores from three pylon locations on the wing. Flutter tests were conducted for the wing with and without external stores. No flutter was encountered for the clean wing at test conditions which simulated the scaled airplane operating envelope. Flutter boundaries were obtained for several external store configurations. The flutter boundaries for the fuel tanks were nearly Mach number independent (occurring at constant dynamic pressure). To study the aerodynamic effect of the fuel tank stores, pencil stores (slender cylindrical rods) which had the same mass and pitch and yaw inertia as the fuel tanks were tested on the model. These pencil store configurations exhibited a transonic dip in the flutter dynamic pressure, indicating that the aerodynamic effect of the actual fuel tanks on flutter was significant. Several flutter analyses methods were used in an attempt to predict the flutter phenomenon exhibited during the wind-tunnel test. The analysis gave satisfactory predictions of flutter for the pencil store configurations, but unsatisfactory correlation for the actual fuel tank configurations.

Cole, Stanley R.↗

NASA NTRS1987

Inviscid transonic wing design using inverse methods in curvilinear coordinates

An inverse wing design method has been developed around an existing transonic wing analysis code. The original analysis code, TAWFIVE, has as its core the numerical potential flow solver, FLO30, developed by Jameson and Caughey. Features of the analysis code include a finite-volume formulation; wing and fuselage fitted, curvilinear grid mesh; and a viscous boundary layer correction that also accounts for viscous wake thickness and curvature. The development of the inverse methods as an extension of previous methods existing for design in Cartesian coordinates is presented. Results are shown for inviscid wing design cases in super-critical flow regimes. The test cases selected also demonstrate the versatility of the design method in designing an entire wing or discontinuous sections of a wing.

Gally, Thomas A.↗

NASA NTRS1987

Wind-tunnel investigation of a full-scale general aviation airplane equipped with an advanced natural laminar flow wing

An investigation was conducted in the Langley 30- by 60-Foot Wind Tunnel to evaluate the performance, stability, and control characteristics of a full-scale general aviation airplane equipped with an advanced laminar flow wing. The study focused on the effects of natural laminar flow and advanced boundary layer transition on performance, stability, and control, and also on the effects of several wing leading edge modifications on the stall/departure resistance of the configuration. Data were measured over an angle-of-attack range from -6 to 40 deg and an angle-of-sideslip range from -6 to 20 deg. The Reynolds number was varied from 1.4 to 2.4 x 10 to the 6th power based on the mean aerodynamic chord. Additional measurements were made using hot-film and sublimating chemical techniques to determine the condition of the wing boundary layer, and wool tufts were used to study the wing stall characteristics. The investigation showed that large regions of natural laminar flow existed on the wing which would significantly enhance cruise performance. Also, because of the characteristics of the airfoil section, artificially tripping the wing boundary layer to a turbulent condition did not significantly effect the lift, stability, and control characteristics. The addition of a leading-edge droop arrangement was found to increase the stall angle of attack at the wingtips and, therefore, was considered to be effective in improving the stall/departure resistance of the configuration. Also the addition of the droop arrangement resulted in only minor increases in drag.

Murri, Daniel G.↗

NASA NTRS1987

A swept wing panel in a low speed flexible walled test section

The testing of two-dimensional airfoil sections in adaptive wall tunnels is relatively widespread and has become routine at all speeds up to transonic. In contrast, the experience with the three-dimensional testing of swept panels in adaptive wall test sections is very limited, except for some activity in the 1940's at NPL, London. The current interest in testing swept wing panels led to the work covered by this report, which describes the design of an adaptive-wall swept-wing test section for a low speed wind tunnel and gives test results for a wing panel swept at 40 deg. The test section has rigid flat sidewalls supporting the panel, and features flexible top and bottom wall with ribs swept at the same angle as the wing. When streamlined, the walls form waves swept at the same angle as the wing. The C sub L (-) curve for the swept wing, determined from its pressure distributions taken with the walls streamlined, compare well with reference data which was taken on the same model, unswept, in a test section deep enough to avoid wall interference.

Goodyer, M. J.↗

NASA NTRS1988

Aerodynamic characteristics of wings designed with a combined-theory method to cruise at a Mach number of 4.5

A wind-tunnel study was conducted to determine the capability of a method combining linear theory and shock-expansion theory to design optimum camber surfaces for wings that will fly at high-supersonic/low-hypersonic speeds. Three force models (a flat-plate reference wing and two cambered and twisted wings) were used to obtain aerodynamic lift, drag, and pitching-moment data. A fourth pressure-orifice model was used to obtain surface-pressure data. All four wing models had the same planform, airfoil section, and centerbody area distribution. The design Mach number was 4.5, but data were also obtained at Mach numbers of 3.5 and 4.0. Results of these tests indicated that the use of airfoil thickness as a theoretical optimum, camber-surface design constraint did not improve the aerodynamic efficiency or performance of a wing as compared with a wing that was designed with a zero-thickness airfoil (linear-theory) constraint.

Mack, Robert J.↗

NASA NTRS1988

Effects of symmetric and asymmetric modes on transonic aeroelastic characteristics of full-span wing-body configurations

To accurately study the transonic aeroelastic characteristics, it is important to model the full aircraft configuration, including asymmetry. Recently, an accurate method of computing unsteady transonic flows on full-span wing-body configurations was developed using the transonic potential flow theory. In this work, the method is further developed to account for the aeroelasticity of full-span wing-body configurations. This is accomplished by simultaneously integrating the unsteady aerodynamic forces and modal structural equations of the wing-body configurations. To validate the method, aeroelastic computations are made for a wing-body configuration with a rectangular wing. The aeroelastic responses of this configuration are correlated with the responses of a similar isolated wing. The comparisons are favorable. Aeroelastic computations associated with symmetric and asymmetric modes are also made to study the influence of modal asymmetry on responses. This new development is further illustrated by computing aeroelastic characteristics of a typical fighter aircraft. The results from this study will be useful in accurately computing the transonic flutter boundaries of aircraft, including those associated with asymmetric modes.

Guruswamy, Guru P.↗

NASA NTRS1989

Influence of wing geometry on leading-edge vortices and vortex-induced aerodynamics at supersonic speeds

An assessment of the influence of wing geometry on wing leading-edge vortex flows at supersonic speeds is discussed as well as the applicability of various aerodynamic codes for predicting these results. A series of delta-wing wind-tunnel models were tested in the NASA Langley Research Center Unitary Plan Wind Tunnel over a Mach number range from 1.6 to 4.6. The data show that wing airfoil has a significant impact on the localized loading on the wing. The experimental data for the flat wings were compared with results from full-potential, Euler, and Parabolized Navier-Stokes (PNS) computer codes. The theoretical evaluation showed that the full-potential analysis predicted accurate results for the attached-flow (alpha = 0 deg) conditions and that the Euler and PNS analyses made reasonable predictions for both attached and separated flow conditions.

Wood, Richard M.↗

NASA NTRS1989

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗

NASA NTRS1989

Development of direct-inverse 3-D methods for applied transonic aerodynamic wing design and analysis

An inverse wing design method was developed around an existing transonic wing analysis code. The original analysis code, TAWFIVE, has as its core the numerical potential flow solver, FLO30, developed by Jameson and Caughey. Features of the analysis code include a finite-volume formulation; wing and fuselage fitted, curvilinear grid mesh; and a viscous boundary layer correction that also accounts for viscous wake thickness and curvature. The development of the inverse methods as an extension of previous methods existing for design in Cartesian coordinates is presented. Results are shown for inviscid wing design cases in super-critical flow regimes. The test cases selected also demonstrate the versatility of the design method in designing an entire wing or discontinuous sections of a wing.

Carlson, Leland A.↗

NASA NTRS1990

Effects of spoiler surfaces on the aeroelastic behavior of a low-aspect-ratio rectangular wing

The relationship between spoiler surfaces and flutter for a low-aspect ratio, rectangular wing is examined. The model design is a rigid wing mounted to the wing tunnel wall using a flexible, rectangular beam. The spoiler surface is composed of thin, rectangular aluminum plates that are vertically mounted to the wing surface. The effects of changes in spoiler geometry and location on wing flutter are studied using wind tunnel testing. It is determined that increases in spoiler height and weight cause an increase in the flutter dynamic pressure; however, variations in the location of the spoiler surfaces have little effect on flutter. Diagrams of the wing model are provided.

Cole, Stanley R.↗

NASA NTRS1990

Measured aerodynamic performance of a swept wing with a simulated ice accretion

The effect of a simulated glaze ice accretion on the aerodynamic performance of a three-dimensional swept wing is studied experimentally. A semispan wing of effective aspect ratio four was mounted from a splitter plate in the OSU subsonic wind tunnel. The model uses a NACA 0012 airfoil section on a rectangular planform with interchangeable tip and root pieces to allow for 0- and 30-degree sweep. Surface pressures were measured at 5 semispan locations on the swept-wing model. The section lift data for the 5 semispan locations are presented and compared with theory and zero-sweep model results. In addition, previously unpublished roughness data from the zero-sweep model is presented here. These data show a large drag and maximum lift penalty due to rough simulated glaze ice. The effect of wing-sweep is seen through a decrease in wing lift performance for both the clean and iced wing.

Khodadoust, A.↗

NASA NTRS1990

Design synthesis and optimization of joined-wing transports

A computer program for aircraft synthesis using a numerical optimizer was developed to study the application of the joined-wing configuration to transport aircraft. The structural design algorithm included the effects of secondary bending moments to investigate the possibility of tail buckling and to design joined wings resistant to buckling. The structural weight computed using this method was combined with a statistically-based method to obtain realistic estimates of total lifting surface weight and aircraft empty weight. A variety of 'optimum' joined-wing and conventional aircraft designs were compared on the basis of direct operating cost, gross weight, and cruise drag. The most promising joined-wing designs were found to have a joint location at about 70 percent of the wing semispan. The optimum joined-wing transport is shown to save 1.7 percent in direct operating cost and 11 percent in drag for a 2000 nautical mile transport mission.

Gallman, John W.↗