Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UV”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

High-Sensitivity NO 2 Gas Sensor: Exploiting UV-Enhanced Recovery in a Hexadecafluorinated Iron Phthalocyanine-Reduced Graphene Oxide

Monitoring ultralow nitrogen dioxide (NO 2 ) concentrations is crucial for air quality management and public health. However, the existing NO 2 gas sensors have several defects, like high cost and power consumption, and exhibit poor selectivity. This study addresses these challenges by presenting a novel hexadecafluorinated iron phthalocyanine-reduced graphene oxide (FePcF 16 -rGO) covalent hybrid sensor for NO 2 detection. This innovative approach, which overcomes the limitations of fabrication cost, energy efficiency, and gas selectivity, is a significant step forward in gas sensor technology. The sensor demonstrates exceptional sensitivity toward ultralow NO 2 concentrations (15.14% response for 100 ppb) with a rapid 60 s UV light-induced recovery. Additionally, the sensor exhibits high selectivity for NO 2 , achieving a limit of detection (LOD) of 8.59 ppb. This approach paves the way for developing cost-effective, energy-efficient, and miniature NO 2 monitoring devices for improved environmental monitoring and enhanced safety in workplaces where NO 2 exposure is a concern.

36 MATERIALS SCIENCE↗

Characterization of the Active Surface Species Responsible for UV-Induced Desorption of O2 from the Rutile TiO2(110) Surface

We have examined the chemical and photochemical properties of molecular oxygen on the (110) surface of rutile TiO2 at 100 K using electron energy loss spectroscopy (EELS), photon stimulated desorption (PSD) and scanning tunneling microscopy (STM). Oxygen chemisorbs on the TiO2(110) surface at 100 K through charge transfer from surface Ti3+ sites. The charge transfer process is evident in EELS by a decrease in the intensity of the Ti3+ d-to-d transition in EELS at ~0.9 eV and formation of a new loss ~2.8 eV. Based on comparisons with the available homogeneous and heterogeneous literature for complexed/adsorbed O2, the species responsible for the 2.8 eV peak can be assigned to a surface peroxo (O2 2-) state of O2. This species was identified as the active form of adsorbed O2 on TiO2(110) for PSD. The adsorption site of this peroxo species was assigned to that of a regular five-cooridinated Ti4+ (Ti5c) site based on comparisons between the UV exposure dependent behavior of O2 in STM, PSD and EELS data. Assignment of the active form of adsorbed O2 to a peroxo species at normal Ti5c sites necessitates reevaluation of the simple mechanism in which a single valence band hole neutralizes a singly charged O2 species (superoxo or O2-) leading to desorption of O2 from a physisorbed potential energy surface. This work was supported by the U.S. Department of Energy (DOE), Office of Basic Energy Sciences, Division of Chemical Sciences, Geosciences, and Biosciences, and the Chemical Imaging Initiative at Pacific Northwest National Laboratory (PNNL), and was performed in the Environmental Molecular Sciences Laboratory (EMSL), a national scientific user facility sponsored by the DOE's Office of Biological and Environmental Research and located at PNNL.

Environmental Molecular Sciences Laboratory↗

Expanding the application of a UV-visible reporter for transient gene expression and stable transformation in plants

Abstract Green fluorescent protein (GFP) has been widely used for monitoring gene expression and protein localization in diverse organisms. However, highly sensitive imaging equipment, like fluorescence microscope, is usually required for the visualization of GFP, limitings its application to fixed locations in samples. A reporter that can be visualized in real-time regardless the shape, size and location of the target samples will increase the flexibility and efficiency of research work. Here, we report the application of a GFP-like protein, called eYGFPuv, in both transient expression and stable transformation, in two herbaceous plant species ( Arabidopsis and tobacco) and two woody plant species (poplar and citrus). We observed bright fluorescence under UV light in all of the four plant species without any effects on plant growth or development. eYGFPuv was shown to be effective for imaging transient expression in leaf and root tissues. With a focus on in vitro transformation, we demonstrated that the transgenic events expressing 1x eYGFPuv could be easily identified visually during the callus stage and the shoot stage, enabling early and efficient selection of transformants. Furthermore, whole-plant level visualization of eYGFPuv revealed its ubiquitous stability in transgenic plants. In addition, our transformation experiments showed that eYGFPuv can also be used to select transgenic plants without antibiotics. This work demonstrates the feasibility of utilizing 1x eYGFPuv in studies of gene expression and plant transformation in diverse plants.

59 BASIC BIOLOGICAL SCIENCES↗

Unusual 5f magnetism in new kagome material UV 6 Sn 6

Materials in the family R V 6 Sn 6 (R = rare earth) provide a unique platform to investigate the interplay between local moments from R layers and nonmagnetic vanadium kagome layers. Yet, the investigation of actinide members remains scarce. Here we report the synthesis of UV 6 Sn 6 single crystals through the self-flux technique. Physical property measurements reveal two uranium-driven antiferromagnetic transitions at T N 1 = 29 K and T N 2 = 24 K, a complex field-temperature phase diagram, and unusual negative domain-wall magnetoresistance. Specific heat and angle-resolved photoemission spectroscopy measurements show a moderate f -electron enhancement to the density of states at the Fermi level (EF), whereas our band structure calculations place the vanadium flat bands 0.25 eV above E F . These findings point to a materials opportunity to expand the uranium 166 family with the goal of enhancing correlations by tuning 5 f and 3 d flat bands to E F .

36 MATERIALS SCIENCE↗

Two excited-state datasets for quantum chemical UV-vis spectra of organic molecules

Abstract We present two open-source datasets that provide time-dependent density-functional tight-binding (TD-DFTB) electronic excitation spectra of organic molecules. These datasets represent predictions of UV-vis absorption spectra performed on optimized geometries of the molecules in their electronic ground state. The GDB-9-Ex dataset contains a subset of 96,766 organic molecules from the original open-source GDB-9 dataset. The ORNL_AISD-Ex dataset consists of 10,502,904 organic molecules that contain between 5 and 71 non-hydrogen atoms. The data reveals the close correlation between the magnitude of the gaps between the highest occupied molecular orbital (HOMO) and the lowest unoccupied molecular orbital (LUMO), and the excitation energy of the lowest singlet excited state energies quantitatively. The chemical variability of the large number of molecules was examined with a topological fingerprint estimation based on extended-connectivity fingerprints (ECFPs) followed by uniform manifold approximation and projection (UMAP) for dimension reduction. Both datasets were generated using the DFTB+ software on the “Andes” cluster of the Oak Ridge Leadership Computing Facility (OLCF).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

UV-activated ZnO films on a flexible substrate for room temperature O 2 and H 2 O sensing

Here, we demonstrate that UV-light activation of polycrystalline ZnO films on flexible polyimide (Kapton) substrates can be used to detect and differentiate between environmental changes in oxygen and water vapor. The in-plane resistive and impedance properties of ZnO films, fabricated from bacteria-derived ZnS nanoparticles, exhibit unique resistive and capacitive responses to changes in O 2 and H 2 O. We also propose that the distinctive responses to O 2 and H 2 O adsorption on ZnO could be utilized to statistically discriminate between the two analytes. Molecular dynamic simulations (MD) of O 2 and H 2 O adsorption energy on ZnO surfaces were performed using the large-scale Atomic/Molecular Massively Parallel Simulator (LAMMPS) with a reactive force-field (ReaxFF). Furthermore, these simulations suggest that the adsorption mechanisms differ for O 2 and H 2 O adsorption on ZnO, and are governed by the surface termination and the extent of surface hydroxylation. Electrical response measurements, using DC resistance, AC impedance spectroscopy, and Kelvin Probe Force Microscopy (KPFM), demonstrate differences in response to O 2 and H 2 O, confirming that different adsorption mechanisms are involved. Statistical and machine learning approaches were applied to demonstrate that by integrating the electrical and kinetic responses the flexible ZnO sensor can be used for detection and discrimination between O 2 and H 2 O at low temperature.

36 MATERIALS SCIENCE↗

Ultra-high Photoresponsivity in Suspended Metal-Semiconductor-Metal Mesoscopic Multilayer MoS 2 Broadband Detector from UV-to-IR with Low Schottky Barrier Contacts

The design, fabrication, and characterization of ultra-high responsivity photodetectors based on mesoscopic multilayer MoS 2 is presented, which is a less explored system compared to direct band gap monolayer MoS 2 that has received increasing attention in recent years. The device architecture is comprised of a metal-semiconductor-metal (MSM) photodetector, where Mo was used as the contact metal to suspended MoS 2 membranes. The photoresponsivity R was measured to be ~1.4 × 10 4 A/W, which is > 10 4 times higher compared to prior reports, while the detectivity D* was computed to be ~2.3 × 10 11 Jones at 300 K at an optical power P of ~14.5 pW and wavelength λ of ~700 nm. In addition, the dominant photocurrent mechanism was determined to be the photoconductive effect (PCE), while a contribution from the photogating effect was also noted from trap-states that yielded a wide spectral photoresponse from UV-to-IR (400 nm to 1100 nm) with an external quantum efficiency (EQE) ~10 4 . From time-resolved photocurrent measurements, a decay time τ d ~ 2.5 ms at 300 K was measured from the falling edge of the photogenerated waveform after irradiating the device with a stream of incoming ON/OFF white light pulses.

36 MATERIALS SCIENCE↗

Impulsive UV-pump/X-ray probe study of vibrational dynamics in glycine

We report an ab-initio study of a pump-probe experiment on the amino-acid glycine. We consider an UV pump followed by an X-ray probe tuned to carbon K-edge and study the vibronic structure of the core transition. The simulated experiment is feasible using existing free electron laser or high harmonic generation sources and thanks to the localization of the core orbitals posseses chemical selectivity. The present theory applies to other experimental schemes, including the use of a THz probe, available with present soft X-ray free electron lasers and/or high harmonic generation sources.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Novel multilayer TiO 2 heterojunction decorated by low g-C 3 N 4 content and its enhanced photocatalytic activity under UV, visible and solar light irradiation

In this paper, we used a facile ball milling, microwave radiation and heating treatment method to achieve the surface modification of TiO 2 with low g-C 3 N 4 concentration, and a multilayer heterojunction composite with TiO 2 as the main part and g-C 3 N 4 as the modification agent was obtained. The obtained materials were analyzed by several characterizations to get information on their chemical composition, crystalline structure, vibrational features and optical properties. The photocatalytic performance was evaluated by degradation of rhodamine B (RhB) and methylene blue (MB) under UV, visible and direct solar light irradiation. Its photocatalytic activity was enhanced depended on the novel structure of g-C 3 N 4 /TiO 2 hybrid and the special Z-scheme electron-hole transfer model of multilayer heterointerfaces. The material preparation and structural features could be useful for the design and development of other photocatalysts with high photocatalytic activity.

54 ENVIRONMENTAL SCIENCES↗

Self-assembled nanostructures from homopolymer induced by UV and solvent exposure

A simple method for creating self-assembled nanostructures using a single polymer system is reported. When spin-coated polystyrene thin films were irradiated with UV light and treated with toluene, unique nanostructures were observed, evolving from star-shaped networks to arrays of concentric circles. The nanostructure formation is a result of differential responses of crosslinked and oxidized products to the solvent by a combined effect of phase separation and solvent swelling. The nanostructures were observed for polymers of different molecular weights, films of different thicknesses, and on various substrates.

36 MATERIALS SCIENCE↗

UV patternable thin film chemistry for shape and functionally versatile self-oscillating gels

We describe a new planar processing chemistry that allows the synthesis and patterning of dynamically self-actuating gels of diverse form. The chemical reaction covalently incorporates a methacrylate-modified ruthenium trisbipyridine monomer within a poly acrylamide (PAAm) gel, modified to provide a flexible chemistry for UV-curable, self-oscillating Belousov–Zhabotinsky (BZ) gels. The photoinitiated polymerization offers significant advantages over previously reported BZ gel chemistries – fast polymerization rates, broad flexibility in the structural and functional attributes that impact the BZ reaction driven mechanics, and a facility for net shape fabrication via projection mode photo lithographic exposure. The facility of the synthetic method enabled an opportunity to broadly explore the structure/property and structure/rate correlations characterizing the dynamics of these gels and develop means to both control and predict the detailed features of the self-oscillating chemical waves they embed. The PAAm systems initiate under the control of transport-dominated influences weighted heavily by the diffusion/depletion of reagents present in the ambient contacting fluid medium. These initiating modes of oscillation are generally unstable temporally, showing shape- and property-sensitive conversions to oscillating modes controlled by the attributes of the gel-phase environment. The present work establishes the nature of these sensitivities, developing insights related to such features in patterned gel objects or films as composition, size, thickness, shape, degree of crosslinking, and gradient forms of structure within the gel. We observed in this work that, across a broad design-rule and compositional space, the PAAm based BZ gel systems exhibit contractions in dimension for regions in which the Ru catalyst is present in the +3 oxidation state (PNIPAAm BZ gels expand in this state). The chemomechanics of the PAAm system are further differentiated from those of PNIPAAm in the generally (and relatively) fast oscillatory rates it can sustain. Furthermore, this work suggests the dynamics in the PAAm gels do not reflect a simple osmotic force driven by differences in the solvation of Ru(II/III) centers. Computational modeling supports a mechanism in which the charge state of Ru centers mediate a differential degree of intra/inter-chain segmental interactions – dynamics that mediate a temporally varying degree of reversibly formed association crosslinks within the gel.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Identifying hydroxylated copper dimers in SSZ-13 via UV-vis-NIR spectroscopy

Cu-Exchanged zeolites are promising materials for the selective conversion of methane to methanol. Their activity is attributed to the presence of small Cu-oxo and Cu-hydroxy clusters, but the nature of active centers in various zeolite structures is still under debate. In this contribution, we combine time dependent density functional theory with spin–orbit coupling to predict the optical spectra of various Cu monomers and dimers in SSZ-13. As a result, we furthermore compare theoretical results to experimental measurements and find that the presence of Cu-hydroxy dimers and Cu monomers could potentially explain the experimentally observed UV-vis-NIR spectra.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Voltage-dependent excitation dynamics in UV-absorbing organic photovoltaics with efficient charge transfer exciton emission

Intermolecular charge-transfer excitons play a central role in determining the performance of organic solar cells as their voltage-dependent formation, dissociation, and recombination dynamics contribute to photocurrent generation, radiative/nonradiative voltage losses, and photovoltaic fill factor. Here, we explore the properties of brightly-emitting wide energy gap (>2 eV) charge transfer excitons by measuring the voltage-dependent photoluminescence, photocurrent, and ultrafast pump–probe transient absorption spectra of organic solar cells employing five UV-absorbing donor molecules that differ only by the length of the oligophenylene or acene group at their core. We find that organic solar cells with a strong correlation between their voltage-dependent photocurrent and charge-transfer exciton photoluminescence have low photovoltaic fill factors as they require voltage to facilitate efficient charge-transfer exciton dissociation. In contrast, solar cells that are efficient can readily generate charges without an applied field and have a separate population of tightly-bound charge-transfer excitons that are responsible for emission. Furthermore, considering that the sum of all excitation loss rates (i.e., recombination and charge extraction) must be equal to the excitation generation rate in the steady state, these voltage-dependent data allow us to solve for the voltage-dependent fate of all excitations in the solar cells and estimate upper and lower bounds for geminate and non-geminate recombination, respectively.

14 SOLAR ENERGY↗