Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “UNLOADING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Processing, electrical and microwave properties of sputtered Tl-Ca-Ba-Cu-O superconducting thin films

A reproducible fabrication process has been established for TlCaBaCuO thin films on LaAlO3 substrates by RF magnetron sputtering and post-deposition processing methods. Electrical transport properties of the thin films were measured on patterned four-probe test devices. Microwave properties of the films were obtained from unloaded Q measurements of all-superconducting ring resonators. This paper describes the processing, electrical and microwave properties of Tl2Ca1Ba2Cu2O(x) 2122-plane phase thin films.

Subramanyam, G.↗

Mass-additive modal test method for verification of constrained structural models

A method for deriving constrained or fixed-base modes and frequencies from free-free modes of a structure with mass-loaded boundaries is developed. Problems associated with design and development of test fixtures can be avoided with such an approach. The analytical methodology presented is used to assess applicability of the mass-additive method for three types of structures and to determine the accuracy of derived constrained modes and frequencies. Results show that mass loading of the boundaries enables local interface modes to be measured within a desired frequency bandwidth, thus allowing constrained modes to be derived with considerably fewer free-free modes than for unloaded boundaries. Good convergence was obtained for a simple beam and a truss-like Shuttle payload, both of which had well-spaced modes and stiff interface support structures. Slow convergence was obtained for a space station module prototype, a shell-like structure having high modal density.

Admire, John R.↗

Structural identification and damage assessment of large space structures

Two different methods are proposed for identifying the structural properties of large orbiting space structures under ordinary service loads, and for assessing potential damage due to impact or other extreme loadings. It is shown that the behavior of a structure in a weightless environment is nonlinear due to unloaded or lightly loaded connections, an effect which not only complicates structural control, but makes the problem of system identification more difficult than for ground based systems. Both proposed methods assume that the structure is subjected to loads imposed by prescribed self stressing systems sufficient to produce repeatable internal force systems in the structure. The first method is based on statical response and requires a survey of structural displacements produced by the self stressing systems. The displacements do not have to be determined completely (i.e., in three directions at each connection), but more displacement information produces more accurate structural stiffness information. It is anticipated that displacement measurements will be taken using on-board laser measurement devices. The second technique employs dynamic stress wave measurement techniques using on-board loading devices and strain gages to track stress wave propagation through the space structure. This approach, which is in its early stages of development, relies on an analysis of transit times of impulsive stress waves and changes in transit times and wave forms due to changes in structural parameters.

Nelson, Richard B.↗

Pressure Distribution over Thick Airfoils - Model Tests

This investigation was undertaken to study the distribution of loading over thick wings of various types. The unloading on the wing was determined by taking the pressure at a number of holes on both the upper and lower surfaces of a model wing in the wind tunnel. The results from these tests show, first, that the distribution of pressure over a thick wing of uniform section is very little different from that over a thin wing; second, that wings tapering either in chord or thickness have the lateral center of pressure, as would be expected, slightly nearer the center of the wings; and, third, that wings tapering in plan form and with a section everywhere proportional to the center section may be considered to have a loading at any point which is proportional to the chord when compared to a wing with a similar constant section. These tests confirm the belief that wings tapering both in thickness and plan form are of considerable structural value because the lateral center of pressure is thereby moved toward the center of the span.

Norton, F H↗

Effect of Threaded and Serrated Holes on the Limited Time and Fatigue Strength of Flat Light-alloy Strips

The investigation was made for the purpose of ascertaining the notch sensitivity of flat strips of light alloy with cylindrical holes under initial tension stress, with special attention to the change in notch-effect factors with the number of load cycles. Then the studies were extended to similar flat strips with pin-loaded holes (tension lugs). This report deals with fatigue tests under initial tension load on flat test specimens of 3116.5 duralumin and AZM 3510.1 electron with plain unloaded and pin-loaded holes (tension lugs) of different forms.

Burnheim, H↗

The theory of contra-vanes applied to the propeller

The optimum circulation distribution and hence the maximum theoretical thrust obtainable for contra-vanes fitted behind propellers is markedly dependent on the number of guide vanes. The outer portion of the vanes, even if projecting considerably beyond the edge of the propeller slipstream, still contribute appreciably to this theoretical gain of thrust. But, owing to the always existing friction of the vanes, the limit of the optimum vane length lies at relatively small diameters. A large hub unloads the vanes. Hence, the guide vanes are best attached to suitable parts of the bodies which would, in any case, be subjected to the slipstream.

Betz, Albert↗

Tests for the determination of the stress condition in tension fields

The present experiments treat the stress of actual tension fields within the elastic range. They give the magnitude of the flexural stresses due to wrinkling. They also disclose, particularly by slightly exceeded buckling load, the marked unloading - as compared with the tension-field theory - of the uprights as a result of the flexural stiffness of the web plate. The test sheets were clamped at the edges and brought to buckling through shearing and compressive stresses applied in the direction of the long sides.

Lahde, R↗

Experiments with airplane brakes

This report begins by examining the forces on the brake shoes. For the determination of the load distribution over the shoes it was assumed that the brake linings follow Hooke's law, are neatly fitted and bedded in by wear. The assumption of Hooke's law, that is, the proportionality between compression of the lining and the absorption of force, is fulfilled to a certain extent for the loading, as becomes apparent from the load tests described further on. But there is a material discrepancy at unloading. From the load distribution we merely defined the position of the normal force resultant, while for the rest, the effect of the distribution was disregarded in the comparison of the different shoe dispositions.

Michael, Franz↗

Riveted joints in thin plates

The method of riveting by forming the closing head under increasing pressure or by a series of hammer blows is investigated. The question as to the best edge distance, i.e. that distance from the rivet center to the plate edge below which it is unadvisable to go and, at the same time useless to go beyond, was examined. The slippage of plates which occurs under the effect of a certain stress, does not completely disappear on unloading. The elastic form change is essentially a function of the elasticity modulus, the slip modulus, the supporting moment, the rivet spacing, etc.

Hilbes, W↗

Servicing capability for the evolutionary Space Station

Since the beginning of the Space Station Freedom (SSF) program the concept of on-orbit servicing of user hardware has been an integral part of the program implementation. The user servicing system architecture has been divided into a baseline and a growth phase. The baseline system consists of the following hardware elements that will support user servicing - flight telerobotic servicer, crew and equipment translation aid, crew intravehicular and extravehicular servicing support, logistics supply system, mobile servicing center, and the special purpose dextrous manipulator. The growth phase incorporates a customer servicing facility (CSF), a station-based orbital maneuvering vehicle and an orbital spacecraft consumables resupply system. The requirements for user servicing were derived from the necessity to service attached payloads, free flyers and coorbiting platforms. These requirements include: orbital replacement units (ORU) and instrument changeout, National Space Transportation System cargo bay loading and unloading, contamination control and monitoring, thermal protection, payload berthing, storage, access to SSF distributed systems, functional checkout, and fluid replenishment. The baseline user servicing capabilities accommodate ORU and instrument changeout. However, this service is limited to attached payloads, either in situ or at a locally adjacent site. The growth phase satisfies all identified user servicing requirements by expanding servicing capabilities to include complex servicing tasks for attached payloads, free-flyers and coorbiting platforms at a dedicated, protected Servicing site. To provide a smooth evolution of user servicing the SSF interfaces that are necessary to accommodate the growth phase have been identified. The interface requirements on SSF have been greatly simplified by accommodating the growth servicing support elements within the CSF. This results in a single SSF interface: SSF to the CSF.

Thomas, Edward F.↗

Efficiency and biofidelity of occupant simulations

Efficiency and biofidelity of occupant simulations are addressed. Topics covered include: R (ratio of rebound energy to initial energy) and G (ratio of permanent deformation to maximum deformation) parameters: ATB simulator unloading behavior; motion of sphere relative to vehicle after vehicle decelerates; sphere for belt restraint; sphere data for wall impact; head acceleration vs. belt slack x-direction (measured); and head acceleration vs. belt slack x-direction (simulated).

Pilkey, Walter D.↗

The p-version of the finite element method in incremental elasto-plastic analysis

Whereas the higher-order versions of the finite elements method (the p- and hp-version) are fairly well established as highly efficient methods for monitoring and controlling the discretization error in linear problems, little has been done to exploit their benefits in elasto-plastic structural analysis. Aspects of incremental elasto-plastic finite element analysis which are particularly amenable to improvements by the p-version is discussed. These theoretical considerations are supported by several numerical experiments. First, an example for which an analytical solution is available is studied. It is demonstrated that the p-version performs very well even in cycles of elasto-plastic loading and unloading, not only as compared to the traditional h-version but also in respect to the exact solution. Finally, an example of considerable practical importance - the analysis of a cold-worked lug - is presented which demonstrates how the modeling tools offered by higher-order finite element techniques can contribute to an improved approximation of practical problems.

Holzer, Stefan M.↗

TlCaBaCuO high Tc superconducting microstrip ring resonators designed for 12 GHz

Microwave properties of sputtered Tl-Ca-Ba-Cu-O thin films were investigated by designing, fabricating, and testing microstrip ring resonators. Ring resonators designed for 12 GHz fundamental resonance frequency, were fabricated and tested. From the unloaded Q values for the resonators, the surface resistance was calculated by separating the conductor losses from the total losses. The penetration depth was obtained from the temperature dependence of resonance frequency, assuming that the shift in resonance frequency is mainly due to the temperature dependence of penetration depth. The effective surface resistance at 12 GHz and 77 K was determined to be between 1.5 and 2.75 mOmega, almost an order lower than Cu at the same temperature and frequency. The effective penetration depth at 0 K is approximately 7000 A.

Subramanyam, G.↗

Material Data Representation of Hysteresis Loops for Hastelloy X Using Artificial Neural Networks

The artificial neural network (ANN) model proposed by Rumelhart, Hinton, and Williams is applied to develop a functional approximation of material data in the form of hysteresis loops from a nickel-base superalloy, Hastelloy X. Several different ANN configurations are used to model hysteresis loops at different cycles for this alloy. The ANN models were successful in reproducing the hysteresis loops used for its training. However, because of sharp bends at the two ends of hysteresis loops, a drift occurs at the corners of the loops where loading changes to unloading and vice versa (the sharp bends occurred when the stress-strain curves were reproduced by adding stress increments to the preceding values of the stresses). Therefore, it is possible only to reproduce half of the loading path. The generalization capability of the network was tested by using additional data for two other hysteresis loops at different cycles. The results were in good agreement. Also, the use of ANN led to a data compression ratio of approximately 22:1.

Alam, Javed↗

Admittance model for the shuttle remote manipulator system in four configurations

A possible scenario for robot task performance in space is to mount two small, dexterous arms to the end of the Shuttle Remote Manipulator System (SRMS). As these small robots perform tasks, the flexibility of the SRMS may cause unsuccessful task executions. In order to simulate the dynamic coupling between the SRMS and the arms, admittance models of the SRMS in four brakes locked configurations were developed. The admittance model permits calculation of the SRMS end-effector response due to end-effector disturbing forces. The model will then be used in conjunction with a Stewart Platform, a vehicle emulation system. An application of the admittance model was shown by simulating the disturbing forces using two SRMS payloads, the Dextrous Orbital Servicing System (DOSS) manipulator and DOSS carrying a 1000 lb. cylinder. Mode by mode comparisons were conducted to determine the minimum number of modes required in the admittance model while retaining dynamic fidelity. It was determined that for all four SRMS configurations studied, between 4 and 6 modes of the SRMS structure (depending on the excitation loads) were sufficient to retain tolerance of 0.01 inches and 0.01 deg. These tolerances correspond to the DOSS manipulator carrying no object. When the DOSS carries the 1000 lb. cylinder, between 15 and 20 modes were sufficient, approximately three or four times as many modes as for the unloaded case.

Papadopoulos, Loukas↗

Design and development of the second generation Mars Habitat

The second generation of Mars Habitat is to be utilized as an advanced permanent base for 20 crew members to live on Mars for a period of 6-12 months. It is designed to be a self-contained environment accommodating five main facilities: living, working, service, medical, and a greenhouse. The objective of the design is to create a comfortable, safe, living environment. Hexamars-2 and Lavapolis-2 are two different concepts for the advanced Mars Habitat. The design team assumes there will be an initial habitat located near or on the site from earlier missions that satisfies the requirement for a short-term habitation for the crew to use while constructing Hexamars-2 or Lavapolis-2. Prefabricated structures and materials will be shipped to the site before the long-term crew members arrive. Partial construction and preparation for the long-term habitat will be done by crew members or robotics from a previous mission. The construction of the long-term base will occur in phases. Hexamars-2 consists of six sphere-shaped inflatable modules that will be partially buried below the Martian surface. The construction of each sphere will occur in ten steps. Shape charges will be used to create the crater in which the spherical structure will be placed. The interior core will be unloaded and put into place followed by the exterior structure. The foundation will be filled, the interior bladder will be inflated, floor-to-floor joists connected, and sand pockets filled. Finally, the life support system and interior partitions are put in place. Each sphere consists of three levels of which the lower level will be safe haven. Particular attention is given to structural support, the dominance of internal pressure, the process of construction, and human factors.

Sabouni, Ikhlas↗

The design of a long-range megatransport aircraft

Aircraft manufacturers are examining the market and feasibility of long-range passenger aircraft carrying more than 600 passengers. These aircraft would carry travelers at reduced cost and, at the same time, reduce congestion around major airports. The design of a large, long-range transport involves broad issues such as: the integration of airport terminal facilities; passenger loading and unloading; trade-offs between aircraft size and the cost to reconfigure these existing facilities; and, defeating the 'square-cube' law. Thirteen Purdue design teams generated RFP's that defined passenger capability and range, based upon team perception of market needs and infrastructure constraints. Turbofan engines were designed by each group to power these aircraft. The design problem and the variety of solutions developed are reviewed.

Weisshaar, Terrence A.↗

Maglev crude oil pipeline

This maglev crude oil pipeline consists of two conduits guiding an endless stream of long containers. One conduit carries loaded containers and the other empty returns. The containers are levitated by permanent magnets in repulsion and propelled by stationary linear induction motors. The containers are linked to each other in a manner that allows them, while in continuous motion, to be folded into side by side position at loading and unloading points. This folding causes a speed reduction in proportion to the ratio of container diameter to container length. While in side by side position, containers are opened at their ends to be filled or emptied. Container size and speed are elected to produce a desired carrying capacity.

Knolle, Ernst G.↗