Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “TRIBOLOGY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Analysis of Microstructure and Sliding Wear Behavior of Co{sub 1.5}CrFeNi{sub 1.5}Ti{sub 0.5} High-Entropy Alloy

Α Co{sub 1.5}CrFeNi{sub 1.5}Ti{sub 0.5} high-entropy alloy (HEA) of the well-known family of CoCrFeNiTi has been designed using empirical parameters. The aim of this design was the production of a HEA with fcc structure that gives ductile behavior and also high strength because of the solid solution effect. The VEC calculations (8.1) supported the fcc structure while the δ factor calculations (4.97) not being out of the limit values, advised a significant lattice distortion. From the other hand, the ΔΗ{sub mix} calculations (− 9.64 kJ/mol) gave strong indications that no intermetallic would be formed. In order to investigate its potential application, the Co{sub 1.5}CrFeNi{sub 1.5}Ti{sub 0.5} HEA was prepared by vacuum arc melting and a primary assessment of its surface degradation response was conducted by means of sliding wear testing using different counterbody systems for a total sliding distance of 1000 m. An effort to correlate the alloy’s wear response with the microstructural characteristics was attempted. Finally, the wear behavior of the Co{sub 1.5}CrFeNi{sub 1.5}Ti{sub 0.5} HEA was compared with that of two commercially used wear-resistant alloys. The results obtained provided some first signs of the high-entropy alloys’ better wear performance when tested under sliding conditions against a steel ball.

36 MATERIALS SCIENCE↗

Paleotribological models using preserved fossil tissue properties reveal functional significance of Eurasian mammoth dental evolution

Eurasian mammoths (Mammuthus) underwent substantial modifications in molar morphology as later-diverging species evolved progressively thinner enamel and increased enamel crest complexity. These features have been hypothesized to reduce whole-tooth wear and extend dental longevity as increasingly graze-dominated diets evolved within the lineage. This hypothesis has yet to be directly tested. Here, in this study, we developed an in-silico wear model using experimentally derived wear rates from fossil and extant proboscidean dental tissues. The models revealed that shifts in tissue topology do not affect whole-tooth wear rate, as inverse trends in lamellar frequency and enamel thickness preserve a consistent surface enamel area fraction; the determining factor of wear. Rather, topological shifts produce a wear-emergent secondary occlusal surface with greater numbers of triturating crests that create a regular, low-relief, file-like shearing pavement. These changes in occlusal architecture likely directly impacted the mastication capacity of Mammuthus dentitions, facilitating their dietary expansion to incorporate fibrous, lower-nutrient graze.

Dental wear↗

Soft matter approach for creating novel protein hydrogels using fractal whey protein assemblies as building blocks

In this study, mesoscopic sized fractal assembly (FA) particles were prepared using whey protein isolate; the coldset gelation properties of FA particles were investigated in-depth. Two types of FA particles (FA -62 and FA -90) with different mean sizes were synthesized through controlled thermal treatment of whey protein solutions at two concentrations (62 g/L and 90 g/L). Particle characteristics e.g. hydrodynamic radius, ζ-potential and surface hydrophobicity were dependent on pH and structure of FA. Transmission electron microscopy (TEM) observation confirmed the fractal morphology and small-angle X-ray scattering (SAXS) analysis suggested an internal fractal structure for the obtained FA particles. Eight cold-set FA protein gels (2 % w/v) were manufactured by controlling two gelling factors at two levels: pH (5.8 and 7.0) and Ca 2+ content (5 mM and 10 mM). Rheological characteristics in the large amplitude oscillatory shear regime revealed that pH 7.0 gels were softer and elastic while pH 5.8 gels were harder and brittle. Rheology Pipkin diagrams demonstrated that the strain softening/stiffening and the shear-thinning/thickening behaviors may be fine-tuned by manipulating the key gelation factors: e.g. FA structure, pH, and Ca 2+ . The entrainment speed-dependent friction coefficient curves showed that at an intermediate velocity regime (6-250 mm s -1 ), FA -90 particles induced hydrogels had superior lubrication effect compared to FA -62 gels. Further, this work demonstrated a food structure design approach regarding tuning texture and lubrication properties of protein gels without changing protein content and protein composition. The optimized protein hydrogels may be used as texturizer for "cleaner label" food formulas and/or as delivery system for carrying micronutrients.

60 APPLIED LIFE SCIENCES↗

Mass transport in a highly immiscible alloy on extended shear deformation

Forced mixing to a single phase or supersaturated solid solution (SSS) and its prerequisite microstructure evolution in immiscible systems has been a focus of research for both fundamental science and a variety of applications. Controlling the formation of SSS by shear deformation assisted processing could enable a material design beyond conventional equilibrium microstructure in immiscible systems. Here, a highly immiscible (mixing enthalpy of ~ 20 kJ·mol -1 ) Cu-50 at. % Cr binary alloy was employed to investigate the microstructure evolution and localized tendencies of SSS during severe shear deformation. The present results demonstrate distinctive microstructure refinement process in each phase and how they lead to localized SSS as a function of shear strain. Preferential dynamic recrystallization occurs in the softer Cu phase due to strain localization, leading to substantial grain refinement. The refinement of Cr phase in the top-most layer, however, is enabled by the progressive evolution of grain lamination, splitting, and fragmentation as a function of shear strain. The eventual SSS is found to be strongly dependent on the local environments that affect the dislocation activity, including the level of microstructure refinement, the interfacial orientation relationship, hardness difference, and supposed stability of oxidation. Ab initio simulations comfirm that it is more favorable to oxidize Cr than Cu at incoherent Cu/Cr interfaces which then limits the mass transport on an incoherent boundary. Our results shed light on the underpinning mechanism for non-equilibrium mass transport in immiscible systems upon severe deformation that can be applicable to a variety of processing techniques aimed at producing immiscible alloys with superior mechanical properties.

36 MATERIALS SCIENCE↗

Treasuring trash: Pt/SrTiO 3 catalysts process plastic waste into high-value materials

Single-use plastics are ubiquitous throughout modern society because they have properties that make them desirable in a wide variety of applications, including low cost of production, high thermal and chemical stability, and tunable mechanical properties. Several of the recycling methods currently used to process single-use plastic waste, such as mechanical recycling and pyrolysis, do not selectively process plastic materials into uniform products, as would be advantageous for repurposing these materials in pursuit of a circular economy. Catalytic hydrogenolysis, whereby C–C bonds in polymers are broken over a supported catalyst in the presence of H 2 , is a promising approach to converting plastics into value-added products that can be sold commercially without further purification. Here, in this account, we present some recent advances in polyolefin hydrogenolysis, with a focus on Pt nanoparticles on SrTiO 3 nanocuboid supports (Pt/STO). Current developments in this field, general challenges, and future directions are discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

AI-enabled Dynamic Finish Machining Optimization for Sustained Surface Integrity

While machining processes are typically leveraged to establish geometric features, many functional characteristics of advanced materials are directly determined by their machining-induced surface integrity (SI). Current modeling approaches struggle to predict surface integrity, and typically neglect the effects of progressive tool-wear, resulting in inefficient ‘static’ process parameters. We present a novel integrated approach based on model-informed artificial intelligence (AI), which optimizes ‘dynamic’ process parameters in real-time. Here, by maximizing the useful life of a cutting tool over which a required set of SI parameters can be maintained, our paradigm will enable significantly more efficient processing of next-generation materials and components.

36 MATERIALS SCIENCE↗

Decoupling of strain and temperature effects on microstructural evolution during high shear strain deformation

The interplay between defect generation by shear strain and defect annihilation by local heating is difficult to predict in shear-assisted processing techniques. In this study, we decoupled the effects of high shear strain and external heating in an immiscible Cu-Nb alloy using a pin-on-disk tribometer to mimic the microstructural evolution of material during solid-phase processing. The change in sub-surface deformation, strain distribution, and redistribution of the second phase as a function of temperature were examined using transmission electron microscopy and atom probe tomography. Zener-Hollomon parameter is used to semi-quantify the deformation of Cu-Nb alloys as a function of strain and temperature.

36 MATERIALS SCIENCE↗

Effect of the addition of Si into V 2 O 5 coatings: Structure and tribo-mechanical properties

Vanadium oxide (V2O5) is one of the lubricious oxides with the potential to be used as a solid lubricant at elevated temperatures. However, the material itself is not hard wear-resistant, so most of the research has focused on adding V into hard nitride coatings that could lead to the formation of a self-lubricating V(2)O(5)layer when heated. The other possible solution, which has been less studied, is to look for mechanisms to enhance the hardness of the oxide coating. In this research, we investigate the effect of the addition of Si into the V2O5 coatings, aiming to find conditions that lead to enhance hardness and/or reduced wear while keeping the high temperature lubricity of the V2O5 structure. For this, Si modified V2O5 coatings were deposited using a dual magnetron sputtering system. The results showed that small additions of Si (< 2.0 at%) improved the hardness of the V2O5 coatings up to 5 times while keeping the same temperature dependence of the coefficient of friction than V2O5. Dry sliding experiments using the pin-on-disc configuration against silicon nitride balls were performed at 25, 300 and 600 degrees C. Wear factors in the 10(-7) mm(3)/Nm range were obtained, indicating a good wear resistance. Further addition of Si into the V2O5 structure led to a loss of the crystalline ordering and a significant reduction in the hardness.

Hall-Petch↗

Enhancing the shredder durability for biomass preprocessing by utilizing wear-resistant cutter materials

Shredders are widely used to reduce biomass feedstock size through the shearing action of the cutter teeth that are susceptible to wear. A series of wear tests using a custom-built shredder was conducted on corn stover feedstock with three cutter materials: a conventional D2 tool steel, iron boriding as a candidate surface treatment, and M42 tool steel as a candidate alloy. Wear tests showed that the iron borided D2 steel significantly increased the tool life compared with the non-treated D2 and M42. Although the M42 cutters initially exhibited less wear than the D2 cutters, the benefit faded as preprocessing progressed. In conclusion, the experimental results demonstrated that the durability of shredder cutters can be substantially improved by applying more wear-resistant tool materials.

09 - BIOMASS FUELS↗

Carbon nanotube (CNT) reinforced 316L stainless steel composites made by laser powder bed fusion: Microstructure and wear response

Carbon nanotube (CNT) reinforced 316L stainless steel (SS) composites were fabricated by laser powder bed fusion (LPBF) additive manufacturing (AM). This study focuses on microstructure evolution, hardness, and wear behavior. The wear behavior for AM 316L SS and 1 wt% CNT/316L SS was studied by a dry sliding test under normal loads of 10, 15, and 25 N. The addition of CNT to 316L SS led to the change of solidification mode from cellular/columnar to dendritic growth, producing grain refinement. Nanoscale dendrites were observed. Although TEM characterization confirmed the existence of CNT in cell interior, most CNT were damaged, resulting in carbon material segregation along cellular/dendritic boundaries. The wear rate was found dramatically decreased due to the improved hardness. Compared to the adhesive and abrasive wear in AM 316L SS, the wear mechanism of CNT/316L composite was adhesion and oxidative wear. Furthermore, enhanced cellular/dendritic boundary strengthening by carbon segregation was the main strengthening mechanism of CNT/316L composite.

36 MATERIALS SCIENCE↗

Additively manufactured and cast high-temperature aluminum alloys for electric vehicle brake rotor application

Electric vehicle brake rotors demand lightweight, high thermal conductivity materials with good resistance to wear, creep, salt corrosion, and thermal fade, all of which present challenges to the traditionally used cast iron. In this work, we investigated the braking performance of recently developed high-temperature aluminum alloys in both cast and 3D printed forms, that possess excellent microstructural and mechanical stability at elevated temperatures. Three aluminum alloys, Al-6Cu-Mn-Zr, Al-9Cu-Mn-Zr, and Al-Ce-Ni-Mn-Zr and a reference cast iron were tested on a sub-scale brake tester against a commercial brake pad material over a range of sliding speeds between 2 and 15 m/s. The performance of these alloys was evaluated for wear resistance, friction behavior, temperature elevation, and surface morphological change. Although all three candidate alloys had lower wear-resistance than cast iron, Al-Ce-Ni-Mn-Zr showed a significantly reduced wear rate in comparison to the Al-Cu-Mn-Zr alloys. Moreover, Al-Ce-Ni-Mn-Zr alloy had the most consistent friction behavior at all sliding speeds and good fade resistance, as the coefficient of friction did not dramatically decrease with temperature rise but stayed within a desirable range of 0.35–0.50 instead. The superior wear resistance and braking performance of the Al-Ce-Ni-Mn-Zr alloy were attributed to its higher hardness, and high temperature yield strength and creep resistance compared with the Al-Cu-Mn-Zr alloys. In conclusion, the results suggest that the braking performance of these aluminum alloys could be further enhanced by increasing the hardness and forming a more stable transfer layer on the sliding surface.

36 MATERIALS SCIENCE↗

Quantitative assessment of sample stiffness and sliding friction from force curves in atomic force microscopy

It has long been recognized that the angular deflection of an atomic force microscope (AFM) cantilever under ''normal'' loading conditions can be profoundly influenced by the friction between the tip and the surface. It is shown here that a remarkably quantifiable hysteresis occurs in the slope of loading curves whenever the normal flexural stiffness of the AFM cantilever is greater than that of the sample. This situation arises naturally in cantilever-on-cantilever calibration, but also when trying to measure the stiffness of nanomechanical devices or test structures, or when probing any type of surface or structure that is much more compliant along the surface normal than in transverse directions. Expressions and techniques for evaluating the coefficient of sliding friction between the cantilever tip and sample from normal force curves, as well as relations for determining the stiffness of a mechanically compliant specimen are presented. The model is experimentally supported by the results of cantilever-on-cantilever spring constant calibrations. The cantilever spring constants determined here agree with the values determined using the NIST electrostatic force balance within the limits of the largest uncertainty component, which had a relative value of less than 2.5%. This points the way for quantitative testing of micromechanical and nanomechanical components, more accurate calibration of AFM force, and provides nanotribologists access to information about contact friction from normal force curves.

36 MATERIALS SCIENCE↗

Optimisation of the blank shape for micro deep drawing of rectangular parts

In this investigation the blank shape for micro deep drawing of rectangular parts was for the first time optimized using FEM method with consideration of the real process conditions in micro forming, i.e. the coefficient of friction and the flow curves of thin foils. The acquired optimized blank shape was then validated by applying it to experiments. For both numerical and experimental investigations a punch with a section of 2x1 mm{sup 2} was used. Aluminum Al99.5 with a sheet thickness of 20 {mu}m was used as blank material in this investigation. A flange free drawn part was successfully obtained from experiment using the blank shape and blank holder force optimized using FEM.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Nanomechanical and nanotribological properties of Nb substituted TiN thin films

Nanomechanical and nanotribological properties of Ti{sub 1-x}Nb{sub x}N (0{<=}x{<=}1) thin films were investigated as a function x. The films were deposited onto polycrystalline nuclear grade 316LN stainless steel (SS) substrate by radio frequency magnetron sputtering in 100% N{sub 2} plasma. The hardness and Young's modulus increased while the friction coefficient and wear volume decreased with increasing Nb substitution. The highest hardness achieved was 31GPa for x=0.77. At the same Nb concentration, the friction coefficient was 0.15 and the elastic recovery was 60%.

36 MATERIALS SCIENCE↗

An in situ shearing x-ray measurement system for exploring structures and dynamics at the solid–liquid interface

Revealing interfacial structure and dynamics has been one of the essential thematic topics in material science and condensed matter physics. Synchrotron-based x-ray scattering techniques can deliver unique and insightful probing of interfacial structures and dynamics, in particular, in reflection geometries with higher surface and interfacial sensitivity than transmission geometries. We demonstrate the design and implementation of an in situ shearing x-ray measurement system, equipped with both inline parallel-plate and cone-and-plate shearing setups and operated at the advanced photon source at Argonne National Laboratory, to investigate the structures and dynamics of end-tethered polymers at the solid-liquid interface. With a precise lifting motor, a micrometer-scale gap can be produced by aligning two surfaces of a rotating upper shaft and a lower sample substrate. A torsional shear flow forms in the gap and applies tangential shear forces on the sample surface. The technical combination with nanoscale rheology and the utilization of in situ x-ray scattering allow us to gain fundamental insights into the complex dynamics in soft interfaces under shearing. In this work, we demonstrate the technical scope and experimental capability of the in situ shearing x-ray system through the measurements of charged polymers at both flat and curved interfaces upon shearing. Furthermore, through the in situ shearing x-ray scattering experiments integrated with theoretical simulations, we aim to develop a detailed understanding of the short-range molecular structure and mesoscale ionic aggregate morphology, as well as ion transport and dynamics in soft interfaces, thereby providing fundamental insight into a long-standing challenge in ionic polymer brushes with a significant technological impact.

36 MATERIALS SCIENCE↗