Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Single Crystal”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Tracking performance of a single-crystal and a polycrystalline diamond pixel-detector

We present a comparative characterization of the performance of a single-crystal and a polycrystalline diamond pixel-detector employing the standard CMS pixel readout chips. Measurements were carried out at the Fermilab Test Beam Facility, FTBF, using protons of momentum 120 GeV/c tracked by a high-resolution pixel telescope. Particular attention was directed to the study of the charge-collection, the charge-sharing among adjacent pixels and the achievable position resolution. The performance of the single-crystal detector was excellent and comparable to the best available silicon pixel-detectors. The measured average detection-efficiency was near unity, ε = 0.99860±0.00006, and the position-resolution for shared hits was about 6 μm. On the other hand, the performance of the polycrystalline detector was hampered by its lower charge collection distance and the readout chip threshold. A new readout chip, capable of operating at much lower threshold (around 1 ke $-$ ), would be required to fully exploit the potential performance of the polycrystalline diamond pixel-detector.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Inhomogeneities in single crystals of cuprate oxide superconductors

The next stage in the evolution of experimental research on the high temperature superconductors will require high quality single crystals and epitaxially grown crystalline films. However, inhomogeneities and other defects are not uncommon in single crystals of cuprate oxide superconductors, so a corollary requirement will be a reliable method for judging the quality of these materials. The application of magnetically modulated resistance methods in this task is briefly described and illustrated.

Moorjani, K.↗

Experimental determination of phonon thermal conductivity and Lorenz ratio of single crystal metals: Al, Cu, and Zn

We use a magnetothermal resistance method to measure lattice thermal conductivity of pure single crystal metals over the intermediate temperature range of 5–60 K. Large transverse magnetic fields are applied to suppress electronic thermal conduction. The total thermal conductivity and the electrical conductivity are measured as functions of applied magnetic field. The lattice thermal conductivity is then extracted by extrapolating the thermal conductivity versus electrical conductivity curve at zero electrical conductivity. We used this method to experimentally measure the lattice thermal conductivity and Lorenz number in single crystal Al (100), Cu (100), and Zn (001) in the intermediate temperature range. Our results show that the measured phonon thermal conductivity versus temperature plot has a peak around ΘD/10, and the Lorenz number is found to deviate from the Sommerfeld value in the intermediate temperature range.

Yao, Mengliang↗

Optical transmission and dimensional stability of single-crystal sapphire after high-dose neutron irradiation at various temperatures up to 688 °C

The use of single-crystal sapphire optical fibers has been considered to extend fiber-optic sensing to the extreme temperature (>1000 °C) environments encountered in nuclear applications. However, before these sapphire fiber–based sensors can be deployed, their optical transmission and dimensional stability (which impacts drift of some sensors) must be characterized under representative testing conditions. Data regarding the optical transmission of sapphire following high-dose neutron irradiation at temperatures >100 °C is extremely limited. This work provides measurements of optical density (i.e., attenuation) and directional dimensional changes in bulk single-crystal sapphire materials irradiated to a fast neutron fluence of 2.4 × 10 21 n/cm 2 (3.5 displacements per atom) at temperatures ranging from 95 to 688 °C. Optical density measured after irradiation at 95 and 298 °C showed ultraviolet and visible absorption bands corresponding to known defect centers and temperature trends that were generally consistent with previous ex situ and in situ measurements made at much lower neutron fluence. However, optical density measured after irradiation at 688 °C was as much as two orders of magnitude higher, indicating that the fundamental mechanism for radiation-induced attenuation changes at this irradiation temperature. Additional analysis and comparison with previous works suggest that the attenuation may result from void formation, leading to increased Rayleigh scattering losses in the material and increased swelling that would also result in drift of Bragg grating-based sensors in sapphire fibers. These results pose serious questions regarding the feasibility of sapphire fiber–based sensors for high-temperature nuclear applications.

36 MATERIALS SCIENCE↗

Real time synchrotron x-ray diffraction measurements to determine material strength of shocked single crystals following compression and release

We present a method to use real time, synchrotron x-ray diffraction measurements to determine the strength of shocked single crystals following compression and release during uniaxial strain loading. Aluminum and copper single crystals shocked along [111] were examined to peak stresses ranging from 2 to 6 GPa. Synchrotron x rays were used to probe the longitudinal lattice strains near the rear free surface (16 and 5 {micro}m depths for Al and Cu, respectively) of the metal crystals following shock compression and release. The 111 diffraction peaks showed broadening indicating a heterogeneous microstructure in the released state. The diffraction peaks also shifted to lower Bragg angles relative to the ambient Bragg angle; the magnitude of the shift increased with increasing impact stress. The Bragg angle shifts and appropriate averaging procedures were used to determine the macroscopic or continuum strength following compression and release. For both crystals, the strengths upon release increased with increasing impact stress and provide a quantitative measure of the strain hardening that occurs in Al(111) and Cu(111) during the shock and release process. Our results for Al(111) are in reasonable agreement with a previous determination based solely on continuum measurements. Two points are noteworthy about the developments presented here: Synchrotron x rays are needed because they provide the resolution required for analyzing the data in the released state; the method presented here can be extended to the shocked state but will require additional measurements.

36 MATERIALS SCIENCE↗

Molecular-field-theory fits to magnetic susceptibilities of antiferromagnetic GdCu 2 Si 2 , CuO, LiCrO 2 , and α-CaCr 2 O 4 single crystals below their Néel temperatures

A recently-developed molecular field theory (MFT) has been used to fit single-crystal magnetic susceptibility χ versus temperature T data below the respective antiferromagnetic ordering temperature T N for a variety of collinear and coplanar noncollinear Heisenberg antiferromagnets. The spins in the system are assumed to interact by Heisenberg exchange and to be identical and crystallographically equivalent. The fitting parameters for χ(T ) of collinear antiferromagnets are measurable quantities: the Weiss temperature θ p in the Curie-Weiss law, TN, χ(T N ), and the spin S. For coplanar noncollinear helix and cycloid structures, an additional fitting parameter is the turn angle between layers of ferromagnetically-aligned spins. Here MFT fits to anisotropic χ(T) data from the literature for single crystals of the collinear antiferromagnets GdCu 2 Si 2 and CuO and the noncollinear antiferromagnets LiCrO 2 with a 120° cycloidal structure and α-CaCr 2 O 4 with a 120° helical structure below their respective N´eel temperatures are presented. The MFT fit to the anisotropic χ(T ≤ T N ) data for CuO is poor, whereas the fits to the data for GdCu 2 Si 2 , LiCrO 2 , and α-CaCr 2 O 4 are quite good. The poor fit for CuO is attributed to the influence of strong quantum fluctuations associated with the small Cu spin and the quasi-one-dimensional magnetism that are not taken into account by the MFT. The magnetic contribution to the zero-field heat capacity of the collinear antiferromagnet GdNiGe 3 at T ≤ T N is also fitted by the MFT.

36 MATERIALS SCIENCE↗

1300 K Creep Behavior of [001] Oriented Ni-49Al-1Hf (at.%) Single Crystals

A study of the 1300 K compressive and tensile creep properties of [001]-oriented NiAl-1Hf (D209) single crystals has been undertaken. Neither post homogenization cooling treatment, minor chemical variations within an ingot or from ingot-to-ingot, nor testing procedure had a significant effect on mechanical behavior; however a heat treatment which dissolved the initial G-phase precipitates and promoted formation of Heusler particles led to a strength reduction. Little primary creep was found utilizing direct measurement of strain, and a misorientation of 18 deg from the [001] did not reduce the creep strength. The effects of heat treatments on properties and a comparison of the flow stress-strain rate data to those predicted by the Jaswon-Cottrell solid solution hardening model indicate that the 1300 K strength in NiAl-1Hf single crystals is mainly due to precipitation hardening mechanisms.

Whittenberger, J. Daniel↗

Formation mechanism of superconducting phase and its three-dimensional architecture in pseudo-single-crystal K x Fe 2-y Se 2

Here, we report how the superconducting phase forms in pseudo-single-crystal K x Fe 2-y Se 2 . In situ scanning electron microscopy (SEM) observation reveals that, as an order-disorder transition occurs, on cooling, most of the high-temperature iron-vacancy-disordered phase gradually changes into the iron-vacancy-ordered phase whereas a small quantity of the high-temperature phase retains its structure and aggregates to the stripes with more iron concentration but less potassium concentration compared to the iron-vacancy-ordered phase. The stripes that are generally recognized as the superconducting phase are actually formed as a remnant of the high-temperature phase with a compositional change after an “imperfect” order-disorder transition. It should be emphasized that the phase separation in pseudo-single-crystal K x Fe 2-y Se 2 is caused by the iron-vacancy order-disorder transition. The shrinkage of the high-temperature phase and the expansion of the newly created iron-vacancy-ordered phase during the phase separation rule out the mechanism of spinodal decomposition proposed in an early report [Wang et al, Phys. Rev. B 91, 064513 (2015)]. Since the formation of the superconducting phase relies on the occurrence of the iron-vacancy order-disorder transition, it is impossible to synthesize a pure superconducting phase by a conventional solid state reaction or melt growth. By focused ion beam-scanning electron microscopy, we further demonstrate that the superconducting phase forms a contiguous three-dimensional architecture composed of parallelepipeds that have a coherent orientation relationship with the iron-vacancy-ordered phase.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Low cycle fatigue of MAR-M 200 single crystals at 760 and 870 deg C

Fully reversed low cycle fatigue tests were conducted on single crystals of the nickel-base superalloys Mar-M 200 at 760 C and 870 C. At 760 C, planar slip (octahedral) lead to orientation-dependent strain hardening and cyclic lives. Multiple slip crystals strain hardened the most, resulting in relatively high stress ranges and low lives. Single slip crystals strain hardened the least, resulting in relatively low stress ranges and higher lives. A preferential crack initiation site which was related to slip plane geometry was observed in single slip orientated crystals. At 870 C, the trends were quite different, and the slip character was much more homogeneous. As the tensile axis orientation deviated from 001 , the stress ranges increased and the cyclic lives decreased. Two possible mechanisms were proposed to explain the behavior: one is based on Takeuchi and Kuramoto's cube cross-slip model, and the other is based on orientation-dependent creep rates.

Milligan, W. W.↗

Electrical and optical properties of Zr doped β -Ga 2 O 3 single crystals

Sn and Si are the typical dopants for achieving tunable n-type conductivity of β -Ga 2 O 3 single crystals grown from the melt. Here, we explore Zr doping in β -Ga 2 O 3 as assessed with UV–vis-NIR, Hall Effect, I–V, and CV measurements and hybrid functional calculations. Single crystals were grown from the melt with nominal Zr doping between 0.1 and 0.5 at% using Czochralski and vertical gradient freeze methods in Ar + O 2 . Furthermore, our results suggest that Zr Ga behaves as a shallow donor, with a measured activation energy of ~10 meV. Our samples show an electron mobility ~73–112 cm 2 V –1 s –1 , resistivity ~0.08–0.01 ohm cm, and carrier density of n = 6.5 × 10 17 –5 × 10 18 cm 3 at room temperature.

36 MATERIALS SCIENCE↗

Structure of the metastable cubic B{sub 1} phase of the La{sub 2}Mo{sub 2}O{sub 9} single crystal

The structure of the metastable B{sub 1} phase of the La{sub 2}Mo{sub 2}O{sub 9} single crystal is investigated using X-ray diffraction. It is established that the crystal structure of the compound under investigation is described by the cubic unit cell with the parameter a = 7.158(5) A, which makes it possible to index approximately 84% of the reflections measured for this single crystal. The structure of the metastable cubic B{sub 1} phase is characterized by a local lowering of the symmetry for the La and Mo atoms, which are displaced from their positions on the threefold axis, thus forming three sites around it with an occupancy of 0.333(2). The O(1) atom in the structure of the metastable cubic B{sub 1} phase remains in the 4a position on the threefold axis but occupies it by only 86%. The O(2) and O(3) atoms located in a general position occupy their own sites with occupancies of 0.77(2) and 0.35(2), respectively. The final R factor of the refinement of this structural model is 2.52%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Piezoelectric response of single-crystal PbZr1-xTixO3 near morphotropic phase boundary predicted by phase-field simulation

The piezoelectric property of hypothetic single-crystal PbZr1-xTixO3 (PZT) is studied using phase-field simulations. The dependence of piezoelectric coefficient (d33) on PbTiO3 compositions (x) near the morphotropic phase boundary (MPB) of PZT was obtained. It is shown that d33 reaches a peak of 720 pC/N at x = 0.47 which is more than 3 times of that for the ceramic counterpart. By analyzing the domain structure of the poled PZT single crystals, we can conclude that the enhancement of d33 near the MPB composition is attributed to the existence of multi-phase and multi-domain.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

GaN Schottky diodes with single-crystal aluminum barriers grown by plasma-assisted molecular beam epitaxy

GaN-based Schottky barrier diodes (SBDs) with single-crystal Al barriers grown by plasma-assisted molecular beam epitaxy are fabricated. Examined using in-situ reflection high-energy electron diffractions, ex-situ high-resolution x-ray diffractions, and high-resolution transmission electron microscopy, it is determined that epitaxial Al grows with its [111] axis coincident with the [0001] axis of the GaN substrate without rotation. In fabricated SBDs, a 0.2 V barrier height enhancement and 2 orders of magnitude reduction in leakage current are observed in single crystal Al/GaN SBDs compared to conventional thermal deposited Al/GaN SBDs. The strain induced piezoelectric field is determined to be the major source of the observed device performance enhancements.

36 MATERIALS SCIENCE↗