Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Chemical banding revealed by chemical etching in a cold-rolled metastable stainless steel

The current work describes the metallographic characterization of the initial microstructure of a cold rolled precipitation hardening semi-austenitic stainless steel (12Cr–9Ni–4Mo–2Cu–1Ti, in wt.%). The use of the Lichtenegger and Blöch (L–B) color etching solution has been shown to reveal not only the phases present in the microstructure, but also the existence of chemical banding along the rolling direction. The L–B reagent has been found to color the microstructure in bands depending on what alloying elements have segregated to each band. Two-dimensional electron probe microanalysis (EPMA) maps have shown that Ni, Cu and Ti segregate together in the bands, while Cr has an opposite behavior. Mo has a mixed segregation behavior although much weaker than the other elements and more prompt to segregate like Ni does. A direct comparison of light optical micrographs with the EPMA maps of the same area of the microstructure has enable to establish a direct relationship between the alloying element band concentration and the resulting etching color contrast obtained with the L–B reagent. Thermodynamic calculations predict that solidification in this steel takes place with ferrite as the primary phase. Equilibrium partitioning coefficient calculations seem to support the observed segregation patterns. - Highlights: • A cold rolled metastable stainless steel has been characterized thoroughly. • EPMA shows that Ni, Cu and Ti segregate together; Cr in an opposite way. • L–B color etching is sensitive to the segregation of these chemical elements. • This chemical banding has been reduced by applying a homogenization heat treatment. • Partitioning coefficient calculations agree with the observed segregation patterns.

36 MATERIALS SCIENCE↗

Microstructural characterization of dissimilar welds between Incoloy 800H and 321 Austenitic Stainless Steel

In this work, the microstructural character of dissimilar welds between Incoloy 800H and 321 Stainless Steel has been discussed. The microscopic examination of the base metals, fusion zones and interfaces was characterized using an optical microscope and scanning electron microscopy. The results revealed precipitates of Ti (C, N) in the austenitic matrix along the grain boundaries of the base metals. Migration of grain boundaries in the Inconel 82 weld metal was very extensive when compared to Inconel 617 weldment. Epitaxial growth was observed in the 617 weldment which increases the strength and ductility of the weld metal. Unmixed zone near the fusion line between 321 Stainless Steel and Inconel 82 weld metal was identified. From the results, it has been concluded that Inconel 617 filler metal is a preferable choice for the joint between Incoloy 800H and 321 Stainless Steel. - Highlights: • Failure mechanisms produced by dissimilar welding of Incoloy 800H to AISI 321SS • Influence of filler wire on microstructure properties • Contemplative comparisons of metallurgical aspects of these weldments • Microstructure and chemical studies including metallography, SEM–EDS • EDS-line scan study at interface.

36 MATERIALS SCIENCE↗

Characterization of carbon ion implantation induced graded microstructure and phase transformation in stainless steel

Austenitic stainless steel 316L is ion implanted by carbon with implantation fluences of 1.2 × 10{sup 17} ions-cm{sup −} {sup 2}, 2.4 × 10{sup 17} ions-cm{sup −} {sup 2}, and 4.8 × 10{sup 17} ions-cm{sup −} {sup 2}. The ion implantation induced graded microstructure and phase transformation in stainless steel is investigated by X-ray diffraction, X-ray photoelectron spectroscopy and high resolution transmission electron microscopy. The corrosion resistance is evaluated by potentiodynamic test. It is found that the initial phase is austenite with a small amount of ferrite. After low fluence carbon ion implantation, an amorphous layer and ferrite phase enriched region underneath are formed. Nanophase particles precipitate from the amorphous layer due to energy minimization and irradiation at larger ion implantation fluence. The morphology of the precipitated nanophase particles changes from circular to dumbbell-like with increasing implantation fluence. The corrosion resistance of stainless steel is enhanced by the formation of amorphous layer and graphitic solid state carbon after carbon ion implantation. - Highlights: • Carbon implantation leads to phase transformation from austenite to ferrite. • The passive film on SS316L becomes thinner after carbon ion implantation. • An amorphous layer is formed by carbon ion implantation. • Nanophase precipitate from amorphous layer at higher ion implantation fluence. • Corrosion resistance of SS316L is improved by carbon implantation.

36 MATERIALS SCIENCE↗

Structure and tribological properties of steel after non-vacuum electron beam cladding of Ti, Mo and graphite powders

The non-vacuum electron beam cladding technique was used to fabricate layers alloyed with Ti, Mo and C on the surface of low-alloyed steel. Two types of experiments were carried out. In the first experiment, a mixture of Ti and graphite powders was used for cladding; in the second, a mixture of Ti, Mo and graphite powders was used for cladding. CaF{sub 2} powder or a mixture of CaF{sub 2} and LiF powders was used as flux. The thickness of the cladded layers was in the range of 2–2.2 mm. The structure of the layers was studied using optical microscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray diffraction (XRD). The microhardness after cladding of the layers fabricated by cladding of Ti and graphite powders was 8–9 GPa, while the microhardness of layers with Mo additions reached 11–12 GPa. The highest wear resistance at sliding friction and friction in abrasive environment was reached in the samples fabricated using Ti, Mo and graphite mixture due to the higher hardness and the martensite–austenite structure of the matrix. The wear resistance against fixed abrasive particles was 2.4 times higher compared to that of carburized and quenched steel. - Highlights: • Ti, C and Mo mixture of powders was cladded using non-vacuum electron beam treatment. • The depth of the cladded layers was 2.0 … 2.2 mm. • The microhardness of layer with Mo, Ti and C additions reached ~ 11 … 12 GPa. • The hardening of the layers caused by the formation of TiC particles and martensitic matrix • Wear resistance of cladded coatings was 2.4 higher than carburized steel.

36 MATERIALS SCIENCE↗

Evolution of microstructure and residual stress during annealing of austenitic and ferritic steels

In this work the recovery and recrystallization processes occurring in ferritic and austenitic steels were studied. To determine the evolution of residual stresses during material annealing the nonlinear sin{sup 2}ψ diffraction method was used and an important relaxation of the macrostresses as well as the microstresses was found in the cold rolled samples subjected to heat treatment. Such relaxation occurs at the beginning of recovery, when any changes of microstructure cannot be detected using other experimental techniques. Stress evolution in the annealed steel samples was correlated with the progress of recovery process, which significantly depends on the value of stacking fault energy. - Highlights: • X-ray diffraction was used to determine the first order and second order stresses. • Diffraction data were analyzed using scale transition elastoplastic models model. • Stress relaxation in annealed ferritic and austenitic steels was correlated with evolution of microstructure. • Influence of stacking fault energy on thermally induced processes was discussed.

36 MATERIALS SCIENCE↗

Influence of differential speed rolling ratio on the ridging behavior of ultra purified 17%Cr ferritic stainless steel

Highlights: • Differential rolling process improves ridging resistance of ferritic stainless steel. • Texture orientation inhomogeneity were attributed to non-uniform deformation. • Shear bands results in homogeneous deformation and recrystallization nucleation. • Uniform recrystallization grains and random orientation grains were obtained. - Abstract: The effect of the differential speed rolling on the ridging resistance and the crystallographic texture evolution of ultra purified 17%Cr ferritic stainless steel was investigated in order to select the optimal procedure for improving the surface quality. In the present study, the three different cold rolling processes were carried out: a conventional cold rolling and two different speed ratios asymmetric rolling. In the conventional cold rolling, the ridging of ferritic stainless steel was pronounced due to the band-like clusters of grains with similar crystallographic orientations. For differential speed rolling, ridging depth decreased and ridging was less pronounced when a higher different speed ratio was applied. The results show that severe ridging is attributed to the presence of band-like clusters of γ-fiber (<111>//ND) oriented grains. The shear bands introduced by differential speed rolling can enhance the nucleation for recrystallization both in grain interiors and grain boundaries, which can fragment the band-like clusters of similar orientation effectively, promoting the random grain orientation and improving surface quality.

36 MATERIALS SCIENCE↗

Evolution of microstructures and mechanical properties during solution treatment of a Ti–V–Mo-containing high‑manganese cryogenic steel

Highlights: • High-Mn cryogenic steels are getting the spotlight in the cryogenic market. • The grain size grew slowly and the yield strength remained almost stabilized with an increase of solutionizing temperature. • The Hall–Petch strengthening coefficient for yield strength was small, estimated to be 153 MPa μm{sup 0.5}. • The weakening effect of solutionizing temperature on grain size was attributed to the nano-sized (Ti, V, Mo)C precipitate. - Abstract: The effect of solution treatment on the microstructure and mechanical properties of a high‑manganese (Mn) twin-induced plastic (TWIP) cryogenic steel that was alloyed from elemental titanium (Ti), vanadium (V) and molybdenum (Mo) was investigated by a variety of techniques such as microstructural characterization, room tensile testing and − 196 °C impact testing. The austenite grain size grew slowly with an increase of the solutionizing temperature (ST). The relatively weak effect of the ST on the austenite grain size is attributed to the superior thermal stability and coarsening resistance of the (Ti, V, Mo)C precipitate, which hindered austenite grain growth. An increase in ST improved the low-temperature toughness (LTT) significantly and decreased the strain hardening rate (SHR), but had no significant effect on the yield strength. The Hall–Petch strengthening coefficient for yield strength was small, and was estimated to be 153 MPa μm{sup 0.5}. Undissolved large-sized chromium (Cr) carbide can deteriorate the LTT significantly. Because of its excellent mechanical properties, high-Mn steel that was alloyed by elemental Ti, V and Mo can be used to manufacture storage tanks for liquefied natural gas.

36 MATERIALS SCIENCE↗

Investigation of annealing temperature on microstructure and texture of Fe-19Cr-2Mo-Nb-Ti ferritic stainless steel

Highlights: • Fe-19Cr-2Mo-Nb-Ti ferritic stainless steel was investigated. • Shear bands provided recrystallization nucleation sites. • Annealing temperature can affect microstructure and texture. • r-bar increased to a maximum value (1.69) and then decreased to 1.42. - Abstract: The evolution of microstructure and texture of Fe-19Cr-2Mo-Nb-Ti ferritic stainless steel annealed at different temperatures was investigated using a combination of X-ray diffraction (XRD) and electron backscatter diffraction (EBSD). EBSD investigations confirm that the in-grain shear bands provide more recrystallization nucleation sites to γ-fiber recrystallization grains with high Taylor factor orientations during cold rolling requiring further annealing for a more homogenous equiaxied grain structure. As the annealing temperatures increase, the grains in center layer are oriented towards {110}∥ND, and the recrystallization grains at 1050 °C are dominated by the uniform and equiaxial γ-fiber grains favourable for the improvement of r-values, while the occurrence of {100} <011> texture detrimental to r-values indicates that an exorbitant annealing temperature can reduce the intensity of γ-fiber textures affecting the formability, accordingly, the average plastic strain ratio of ferritic stainless steel increases sharply up to a maximum value (1.69) and then decreases to a certain value (1.42).

36 MATERIALS SCIENCE↗

Crystallography of intergranular corrosion in sensitized austenitic stainless steel

Highlights: • Intergranular corrosion (IGC) in stainless steel was crystallographically discussed. • Grain boundaries (GBs) were classified based on the coincidence site lattice (CSL). • Influence of the Σ value on their IGC susceptibility had a wide range scatter. • IGC susceptibility was characterized by the Σ value and unit cell area of CSL GBs. - Abstract: This study deals with the susceptibility to intergranular corrosion (IGC) in type 304 austenitic stainless steel from a crystallographic viewpoint. An IGC test was conducted using oxalic acid and sensitized stainless steel, whose crystal orientation was analyzed by electron backscattered diffraction (EBSD). GBs were classified according to the misorientation of adjacent grains, and subclassified using the Σ value based on the coincidence site lattice (CSL) model. The width of corroded groove was measured for each GB category, and the effect of GB category on the susceptibility to IGC was examined. Then, the area of the unit cell of CSL boundaries was used to characterize the susceptibility to IGC of CSL boundaries. It was found that no IGC occurred in low-angle GBs with a misorientation of 15°, the width of corroded groove at each Σ boundary exhibited large scatter. The relationship between the width and unit cell area was characterized by a sigmoid curve, and the susceptibility to IGC was well described by the unit cell area.

36 MATERIALS SCIENCE↗

Study on the creep deformation behavior and characterization of 9Cr-1Mo-V-Nb steel at elevated temperatures

Highlights: • The true creep deformation mechanism has been found by an evaluation of threshold stresses. • The analysed creep data suggest that the rate-controlling mechanism of creep is dislocation climb. • Coarsening of the M{sub 23}C{sub 6} carbides has been observed at 650 °C and 700 °C during creep. In this study, creep tests were conducted on a set of specimens made from the same tube of T91 steel at different temperatures (600 °C, 650 °C and 700 °C) with the applied stresses ranging from 30 MPa to 180 MPa and rupture times from 28.7 to 7957 h for understanding the creep mechanism. The stress dependence of minimum creep rates exhibits a power law with different exponents were found to be 14.3, 11 and 4.6 at 600 °C, 650 °C and 700 °C, respectively. Activation energy of creep was determined to be ~573 kJ/mol, which is ~53% higher than that of the lattice self-diffusion in α-iron. Based on the stress exponents, the modified Bird-Murkherjee-Dorn (BMD) equation was used to find the threshold stresses which has shown the strongly dependent on the test temperature. After incorporating the threshold stress, true activation energy of creep was found to be decreased ~271 kJ/mol, which is equivalent to that of lattice-self diffusion in α-iron. This subsequently led to evaluation of true stress exponent ~4. The results of creep data suggest that the rate-controlling mechanism of creep is dislocation climb for T91 steel. Microstructural observation of T91 steel is mainly consisting of lath martensite structure with fine MX carbonitrides and M{sub 23}C{sub 6} carbides were characterized using the scanning and transmission electron microscopes. The stress dependence of creep rupture life has shown that the operating mechanism of creep is similar. Furthermore, creep data was analysed for validity of the Monkman-Grant relationship and creep damage tolerance parameter. The qualitative microstructure of the crept samples show that less number of MX carbonitrides within grains is responsible for creep cavity formation and decreasing the rupture life. Thus, microstructural degradation is attributed to M{sub 23}C{sub 6} carbides coarsened and dislocation sub-structure boundaries are mainly responsible for creep damage. The fracture morphology of the samples has revealed with dimples is a typical transgranular ductile failure.

36 MATERIALS SCIENCE↗

Structure of Oxide Nanoparticles in Fe-16Cr MA/ODS Ferritic Steel

Oxide nanoparticles in Fe-16Cr ODS ferritic steel fabricated by mechanical alloying (MA) method have been examined using high-resolution transmission electron microscopy (HRTEM) techniques. A partial crystallization of oxide nanoparticles was frequently observed in as-fabricated ODS steel. The crystal structure of crystalline oxide particles is identified to be mainly Y{sub 4}Al{sub 2}O{sub 9} (YAM) with a monoclinic structure. Large nanoparticles with a diameter larger than 20 nm tend to be incoherent and have a nearly spherical shape, whereas small nanoparticles with a diameter smaller than 10 nm tend to be coherent or semi-coherent and have faceted boundaries. The oxide nanoparticles become fully crystallized after prolonged annealing at 900 C. These results lead us to propose a three-stage formation mechanism of oxide nanoparticles in MA/ODS steels.

36 MATERIALS SCIENCE↗

Effects of Sample Geometry and Loading Rate onTensile Ductility of TRIP800 Steel

The effects of sample geometry and loading rate on the tensile ductility of a commercial grade Transformation Induced Plasticity (TRIP) steel are examined in this paper. Quasistatic tensile tests were performed for the 1.2mm gauge TRIP800 steel sheets with two geometries: sub-sized ASTM E-8 and a custom designed miniature tensile sample. Sample geometry effects on post-uniform elongation are discussed together with other experimental data reported in the open literature. Further discussions on the effects of sample geometry are cast in the context of mesh-size dependent ductility in finite element-based engineering simulations. The quasi-static tensile curve for the miniature sample is then compared with the split Hopkinson bar results at the loading rates of 1700-S-1 and 2650-S-1 with the same sample design. In contrary to the typical strain rate sensitivity results for mild steel where the dynamic strength increase at high strain rate usually occurs at the price of ductility reduction, our results show that the TRIP800 under examination has positive strain rate sensitivity on both strength and ductility. Images of the deformation process captured by high speed camera together with scanning electron microscopy (SEM) near the fracture zone are also used to elucidate the different deformation modes at different loading rates.

36 MATERIALS SCIENCE↗

Effect of friction stir processing on the tribological performance of high carbon steel.

Friction stir processing (FSP) was applied to 1080 carbon steel as a means to enhance the near-surface material properties. The process transformed the original pearlite microstructure to martensite, resulting in significant increase in surface hardness. This surface hardening produced a significant benefit for friction and wear behavior of the steel as measured by unidirectional sliding ball-on-flat testing. Under dry sliding, FSP reduced friction coefficient by approximately 25% and wear rate by an order of magnitude. Under oil lubrication, FSP had only a marginal effect on friction, but it reduced wear rates by a factor of 4. The improvement in tribological performance of 1080 steel by FSP technique is attributed to reduced plasticity of the near-surface material during sliding contact

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Effect of Controlled Hot Rolling Parameters on Microstructure of a Nb-Microalloyed Steel Sheet

The design of controlled rolling process of microalloyed steel sheets is affected by several factors. In this investigation, effect of the reheating, finishing and coiling temperatures of rolling, which are considered as the most effective parameters on microstructure of hot rolled products has been studied. For this purpose, seven different reheating temperatures between 1000 to 1300 deg. C with 50 deg. C increments, three different finishing temperatures of 950, 900 and 850 deg. C below the non-recrystallization temperature and one temperature of 800 deg. C in the inter critical range and four different coiling temperatures of 550, 600, 650 and 700 deg. C were chosen. By soaking the specimens in furnace, the grain coarsening temperature (T{sub gc}) is obtained about 1250 deg. C. Hence, for these kinds of steels, the reheating temperature 1200 to 1250 deg. C is recommended. Moreover, it is observed that decreasing the coiling and finishing temperatures causes more grain refinement of microstructure and the morphology is changed from polygonal ferrite to acicular one. Findings of this research provide a good connection among reheating, finishing and coiling temperatures and microstructural features of Nb-microalloyed steel sheets.

36 MATERIALS SCIENCE↗

Hydrostatic Microextrusion of Steel and Copper

The paper presents an experimental investigation based on hydrostatic micro extrusion of billets in low carbon steel and commercially pure copper, and the relevant results. The starting billets have a diameter of 0.3 mm and are 5 mm long; a high pressure generator consisting of a manually operated piston screw pump is used to pressurize the fluid up to 4200 bar, the screw pump is connected through a 3-way distribution block to the extrusion die and to a strain gauge high pressure sensor. The sensor has a full scale of 5000 bar and the extrusion pressure is acquired at a sampling rate of 2 kHz by means of an acquisition program written in the LabVIEW environment. Tests have been conducted at room temperature and a lubricant for wire drawing (Chemetall Gardolube DO 338) acts both as the pressurizing fluid and lubricant too. In addition, billets were graphite coated. Different fluid pressures and process durations have been adopted, resulting in different extrusion lengths. The required extrusion pressure is much higher than in non-micro forming operations (this effect is more evident for steel). On the cross section of the extruded parts, hardness and grain size distribution have been measured, the former through Vickers micro hardness (10 g load) tests. In the case of the extrusion of copper, the material behaves as in microdrawing process. In the case of the extrusion of steel, the hardness increases from the core to the surface as in the drawing process, but with lower values. The analysis evidenced the presence of the external layer, but its thickness is about 1/3 of the external layer in the drawn wire and the grains appear smaller than in the layer of the drawn wire. The extruding force required along the extruding direction is higher (22-24 N) than the drawing force along the same direction (12 N): being the material, the reduction ratio, the die sliding length the same in both cases, the higher extrusion force should be caused by a higher tangential friction force and/or a higher redundant work of deformation and/or a different material behaviour. Which is the real mechanism is not clear at present, but surface layer grains in extrusion are more deformed than in wire drawing. For this reason the deformation inhomogeneity increases in extrusion and the material under the highly deformed surface layer should be subjected to lower strains, strain hardening and finally resulting in lower hardness.

36 MATERIALS SCIENCE↗

Study of electroless Ni-W-P alloy coating on martensitic stainless steel

Electroless nickel phospor (Ni-P) is widely used in many industries due to their corrosion and wear resistance, coating uniformity, and ability to coat non-conductive surfaces. The unique properties of tungsten such as high hardness, higher melting point, lower coefficient of linear thermal expansion, and high tensile strength have created a lot of interest in developing ternary Ni-W-P alloys. This article presents the study of electroless Ni-W-P alloys coating using acid or alkaline bath on martensitic stainless steel. Nickel sulfate and sodium tungstate were used as nickel and tungsten sources, respectively, and sodium hypophosphite was used as a reducing agent. Acid or alkaline bath refer to bath pH condition was adjusted by adding sulfuric acid. Martensitic stainless steel was immersed in Ni-W-P bath for 15, 30, and 60 minutes. The substrate of martensitic stainless steel was subjected to pre-treatment (polishing and cleaning) and activation prior to electroless plating. The plating characteristics were investigated for concentration ratio of nickel and hypophosphite (1:3), sodium tungstate concentration 0,1 M, immersion time (15 min, 30 min, 60 min), and bath condition (acid, alkaline). The electroless Ni-W-P plating was heat treated at 400°C for 1 hour. Deposits were characterized using scanning electron microscope (SEM) and corrosion measurement system (CMS).

36 MATERIALS SCIENCE↗

The mechanical properties of austenite stainless steel 304 after structural deformation through cold work

The 304 stainless steel (SS) type is widely used in oil and gas operations due to its excellent corrosion resistance. However, the presence of the fine sand particles and H{sub 2}S gas contained in crude oil could lead the erosion and abrasion in steel. In this study, cold rolled treatments were conducted to the 304 SS in order to increase the wear resistance of the steel. The cold work has resulted in thickness reduction to 20%, 40% and 60% of the original. Various microstructural characterizations were used to analyze the effect of deformation. The hardness characterization showed that the initial hardness value increased from 145 HVC to 395 HVC as the level of deformation increase. Further, the wear resistance increased with the deformation rate from 0% to 40% and subsequently decreased from 40% to 60% deformation rate. Microstructural characterization shows that the boundary change to coincide by 56 µm, 49 µm, 45 µm, and 43 µm width and the grain go to flatten and being folded like needles. The effect of deformation on the grain morphology and structure was also studied by optical metallography and X-Ray Diffraction. It is shown that the deformation by means of a cold rolled process has transformed the austenite structure into martensitic structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Corrosion Behavior of Steels in Supercritical CO 2 for Power Cycle Applications

In order to understand issues with corrosion of heat exchanger materials in direct supercritical carbon dioxide (sCO 2 ) power cycles, a series of autoclave exposure experiments and electrochemical experiments have been conducted. Corrosion behaviors of 347H stainless steel and P91 martensitic-ferrtic steel in sCO 2 environment have been compared. In autoclave exposure tests performed at 50°C- 245°C and 80 bar. Mass change measurements, surface characterization, and corrosion product analysis have been conducted to understand the corrosion behavior of steels in sCO 2 containing H 2 O and O 2 . Electrochemical tests performed at room temperature and 50°C, a simulation environment of water condensation phase with dissolved CO 2 was prepared to evaluate the corrosion resistance of materials. From both types of experiments, generally 347H showed higher corrosion resistance than P91.

01 COAL, LIGNITE, AND PEAT↗