Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SLIP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Kink mechanism in Cu/Nb nanolaminates explored by $\mathcal{in}$ $\mathcal{situ}$ pillar compression

We report Nano metallic laminates (NMLs) exhibit different failure modes depending on the loading conditions due to their mechanical anisotropies. Kinking is a typical failure mode in many NMLs compressed along a layer-parallel direction. However, a detailed description of the microstructure evolution during kink band (KB) formation and an in-depth understanding of the formation mechanisms are lacking. In this work, the KB process is investigated in Cu/Nb NMLs by in situ micro pillar compression in the scanning electron microscope (SEM) along a layer-parallel direction. Post-mortem S/TEM and transmission Kikuchi diffraction (TKD) analyses show that kink banding leads to significant microstructure changes characterized by an accumulation of geometrically necessary dislocations (GNDs) and of tilt geometrically necessary boundaries (GNBs) near KB boundaries (KBBs). The distinct microstructure evolution implies that KB formation is facilitated by the inhomogeneous microstructures resulting in constrained deformation modes. Specifically, dislocations active on slip planes nearly parallel to the interfaces make a major contribution to kink evolution after the onset of kinking. Once layer-parallel slip systems are activated, preexisting lattice dislocations and dislocations nucleating from interfaces will accumulate as GNDs near KBBs via the stochastic storage of lattice dislocations that have certain Burgers vectors. GNDs can further transform into GNBs via cross-slip and climb driven processes near the KBB. Furthermore, GNBs near KBBs can grow by incorporating more GNDs or by coalescence to accommodate the KB evolution. We further hypothesize that microstructural perturbations and their ensuing stresses can initiate KB formation in Cu/Nb NMLs.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Crystal plasticity model of BCC metals from large-scale MD simulations

Accurate crystal plasticity models that faithfully capture the behavior of single crystals under a wide range of loading conditions, such as loading direction, strain rate, and temperature, are still lacking. Here we introduce a novel approach in which a crystal plasticity (CP) model is informed directly from and calibrated to large-scale quantum-accurate MD simulations in which single crystal BCC Ta serves as a testbed material. By analyzing our large set of MD simulations several key insights are obtained leading us to modify constitutive assumptions in order to address deficiencies of existing CP models. Importantly, we observe that the standard notion of fixed slip systems – pairs of slip directions and slip planes – is inadequate for describing high-rate plasticity in BCC tantalum at room temperature. Instead, pencil glide defined as dislocation motion in the maximum resolved shear stress planes (MRSSP) of each Burgers vector is fully consistent with our MD simulation data while providing significant simplifications of the constitutive relations. Herein, our resulting new CP model closely matches the behavior of single crystals observed in high-rate MD simulations while being fully consistent with lower rate experimental results.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Low pressure direct injection strategies effect on a small SI natural gas two-stroke engine’s energy distribution and emissions

This paper examines methods to simultaneously improve efficiency and reduce emissions from a 34 cc air-cooled two-stroke engine configured to operate on natural gas, using tuned intake plus exhaust resonators designed from Helmholtz resonance theory to promote effective scavenging. The engine was developed for novel application in a small, free piston engine for decentralized power generation. Operation occurred at wide-open-throttle at a speed of 5400 RPM for both port injection (PI) and low-pressure direct injection (LPDI). In both cases, the electronic ignition timing was adjusted for maximum brake torque, while the fuel was adjusted such that both rich and lean combustion were examined. The LPDI engine was then operated over a variety of engine speeds. An energy balance was completed for both PI and LPDI operation, which quantified all energy pathways, as engine operating regimes changed. Results showed that exhaust chemical energy (ECE) for LPDI was reduced significantly when compared to PI, mostly due to less fuel slip. The fuel slip rate ranged from 35 to 40% for PI operation while it was in the range of 6–20% for LPDI operation. However, mixture stratification with LPDI operation increased carbon monoxide emissions. The start-of-injection (SOI) was also examined, targeting a SOI to provide the highest trapping efficiency and most stable combustion. For LPDI operation, trapping efficiency, which is function of engine speed, showed significant effects on overall efficiency and fuel slip. Air volumetric efficiency increased due to the absence of gaseous fuel within the intake manifold. It was shown that, relative to PI, the overall engine indicated efficiency increased by 90% to a maximum indicated efficiency of 30% for LPDI operation with a SOI of 180 CAD BTDC.

42 ENGINEERING↗
DOE OSTI2021

Identification of crystal plasticity model parameters by multi-objective optimization integrating microstructural evolution and mechanical data

Crystal plasticity models evolve a polycrystalline yield surface using meso-scale descriptions of deformation mechanisms. The activation of deformation mechanisms is governed by crystallography and a set of model parameters, which are typically calibrated through the fitting of mechanical data such as stress–strain curves and elastic lattice strains. Microstructural data such as phase fractions and texture evolution are used for verifying crystal plasticity parameters. In this study, we use a multi-objective genetic algorithm to identify hardening parameters from flow stress curves with an option to incorporate texture into the optimization approach. Robust, generalized objective functions are developed and used to identify sets of parameters pertaining to dislocation density-based hardening laws in visco-plastic and elasto-plastic self-consistent (VPSC and EPSC) homogenization models. First, the parameters are identified for pure Nb directly from texture using an objective function based on generalized spherical harmonics. Since texture evolution is driven by the relative contribution of active slip systems, the parameters governing the evolution of slip resistance ratios can be recovered from fitting discrete textures at a series of strains. Next, a comprehensive set of load reversal data for dual phase (DP) 780 steel is used to fit a hardening law and a back-stress law in EPSC. Finally, parameters pertaining to a complex hardening law for the evolution of slip and twinning in pure α-Ti are identified. Remarkably, using texture as an objective in combination with stress–strain objectives constrains the model of Ti to fully reproduce not only stress–strain and texture evolution but also hierarchical twinning measurements as a function of initial grain size and texture. Furthermore, given an appropriate model fit to representative experimental texture evolution, underlying twin volume fractions contributing to texture evolution can be predicted.

42 ENGINEERING↗
DOE OSTI2018

Analytic model of the γ -surface deviation and influence on the stacking fault width between partial dislocations

The stacking fault width (R$_{eq}$) between partial dislocations within an FCC crystalline lattice characterizes the onset of numerous plastic flow mechanisms, as well as the relationship between material strength and grain size. Continuum models traditionally consider a complete unit of dislocation slip ( b ) along the $\langle{110}$$\rangle$ direction distributed between two discrete partial dislocations, each with a fixed partial Burgers vector ( b p ), which bound a stacking fault. Across the stacking fault, the vectorial slip is assumed to be constant, yielding a constant intrinsic stacking fault energy density, $\gamma$$_{isf}$ Here, we demonstrate that the vectorial displacement path taken in accomplishing a complete unit of slip (b) deviates from the expected displacement path containing the local minima, $\gamma$$_{isf}$ leading to a correction in the nominally derived stacking fault width. The magnitude of the correction depends on both the net orientation of the dislocation within the lattice, and also the degree of relaxation of each partial Burgers vector along the $\langle{\bar{1}12}$$\rangle$ direction. We derive a simple analytic model for the corrected stacking fault width, explicitly accounting for the deviation, by introducing a variable ξ (0 < ξ < 1), which governs the magnitude of each partial dislocation component along the $\langle{\bar{1}12}$$\rangle$ direction. Significantly, our model predicts a correction to R$_{eq}$ of ~$\mathscr{O}$ (|b|) for the nominally screw dislocation, and has no noticeable influence on nominally edge dislocations. We apply our model towards computing the stacking fault width of several FCC metals, and demonstrate excellent agreement both with our own numerical data as well as that obtained from ab initio and Molecular Statics (MS) methods within the literature. Lastly, the results from this study demonstrate that, upon judicious application, discrete linear elastic models are successful in reproducing elastic interactions as computed from higher fidelity models on the spatial scale of metallic dislocation cores.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Four-dimensional microstructurally small fatigue crack growth in cyclically loaded nickel superalloy specimen

Here, we nondestructively image a low-solvus high refractory (LSHR) nickel base specimen microstructure during cyclic loading to characterize crack propagation during the microstructurally small crack (MSC) growth regime. Micro-computed tomography (uCT) is used to characterize the material density and identify crack interfaces, while high-energy diffraction microscopy (HEDM) provides snapshots of the microstructural orientation field changes. From these measurements, data are computationally reconstructed and coregistered to describe the specimen’s configuration before load, before crack nucleation, and throughout the crack propagation/loading process. An MSC forms at a FIB-cut notch, which was previously placed to concentrate stress at the center of the specimen gauge, and propagates along a facet parallel to the local {1 1 1} crystallographic plane. Analysis of available crystallographic slip directions and measured point-to-point disorientation axes indicate probable single and coplanar slip activity along FCC octahedral planes within this region. Similar analyses of other crack propagation facets reveal generally slower growth along directions favoring zig-zag cross and codirectional cross slip, which are often disfavored at room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Unraveling the dislocation–precipitate interactions in high-entropy alloys

The precipitates play a significant role in not only enhancing the strength, but also maintaining the high toughness in alloys. However, the interactions of the nanoscale precipitates with dislocations in the high entropy alloys (HEAs) are difficult to observe directly by in-situ TEM experiments due to the limits of the resolution and time. Here, using atomic simulations we report the synergistic strengthening of the coherent precipitate and atomic-scale lattice distortion in the HEAs at cryogenic/elevated temperatures. The effects of temperature, chemical disorder, precipitate spacing, precipitate size, elemental segregation, and dislocation-cutting number on the critical stress for the dislocation to overcome a row of precipitates are studied. A random stacking fault energy landscape along the slip plane, the lattice distortion at different temperatures, and the interface/surface energy at various crystallographic orientations are obtained. Compared with the traditional metals and alloys, HEAs have the severe atomic-scale lattice distortions to generate the local high tensile/compressive stress fields. This complex stress causes the dislocation line to bend, and thus improves the dislocation slip resistance, resulting in the strong solid-solution strengthening. The stacking fault strengthening induced by the obvious difference of the stacking fault energies between the HEA matrix and precipitate (within the inner of the HEA matrix), and the formation of the antiphase domain boundary contribute to the high strength. The precipitate embedded by the solute atoms produces the strong lattice distortion to enhance the dislocation slip resistance at high temperatures. Hence, the current results provide the mechanistic insight into the phenomenon that the coherent precipitate combined with the severe atomic-scale lattice distortion can enhance the strength at cryogenic/elevated temperatures to further broaden the scope of applications of advanced HEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A crystal plasticity finite element model embedding strain-rate sensitivities inherent to deformation mechanisms: Application to alloy AZ31

We report the fundamental power-law relationship representing the flow rule in crystal visco-plasticity ensures uniqueness in the selection of slip systems accommodating imposed plastic strain-rates. The power-law relationship also introduces an artificially high strain-rate sensitivity in crystal plasticity simulations, unless a high value of the power-law exponent is used. However, the use of high values for the exponent is limited by numerical tractability. This paper presents a numerical method implemented in a crystal plasticity finite element (CPFE) model for embedding any value of the power-law exponent reflecting the true material strain-rate sensitivity. Importantly, the method does not increase computation time involved in the simulations. The enhanced CPFE model is used to interpret and predict a complex strain-rate sensitive response and microstructural evolution of AZ31 Mg alloy. Measured values of strain-rate sensitivity for slip and twinning modes are used in the simulations. Calculations show that the model successfully captures the phenomena pertaining to the effect of changing applied strain-rate on the mechanical response including flow stress and evolution of texture and twinning for a broad range of strain-rates ranging from 10 -3 s -1 to 10 3 s -1 and loading orientations in tension and compression. It is shown that such predictions are a consequence of not only relative amounts of slip and twinning activities driven by a set of accurately characterized hardening law parameters but also values of the strain-rate sensitivities inherent to individual deformation mechanisms. Besides, the model validates the measured strain-rate dependency of deformation mechanisms while accurately reproducing the mechanical data. Hence, the model can be used to verify and further refine or infer measured strain-rate sensitivity per deformation mechanism by reproducing experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Tensile and compressive plastic deformation behavior of medium-entropy Cr-Co-Ni single crystals from cryogenic to elevated temperatures

The equiatomic Cr-Co-Ni medium-entropy alloy has the face-centered cubic (FCC) structure. Bulk single crystals of this alloy were grown and tested in tension and compression between 14 K and 1373 K with the loading axis parallel to [23]. At room temperature, the critical resolved shear stress (CRSS) for {111}<10> slip is 65 ± 5 MPa and does not exhibit a tension-compression asymmetry. It does, however, increase significantly as the test temperature decreases. A dulling of this temperature dependence occurs below 50 K, which may be due to the inertia effect. When the measured values above 50 K are extrapolated to lower temperatures, a value of 225 MPa is estimated for the CRSS at 0 K. This is larger than that (168 MPa) previously determined for the equiatomic Cr-Mn-Fe-Co-Ni high-entropy alloy using a similar procedure. The stacking fault energy of the present Cr-Co-Ni is estimated to be about 14 mJm-2, which is sufficiently low to account for deformation twinning both at 77 K and room temperature. Twinning at 77 K occurs on conjugate (1) planes at an onset shear stress of 482 MPa after primary slip and propagates in the form of Lüders deformation. At room temperature, twinning occurs uniformly throughout the gauge section on primary (111) planes at an onset shear stress of 381 MPa after primary and subsequent conjugate slip. Thin layers with the hexagonal close-packed stacking are observed in association with twinning both at 77 K and room temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Coupled geomechanical investigation of depletion-induced fault reactivation

Fault reactivation during subsurface fluid production pose significant challenges to safe and sustainable resource extraction. Here, this study presents a three-dimensional coupled geomechanical framework to investigate the processes driving fault reactivation, capturing the interactions between reservoir dynamics and geomechanical responses. Verification against theoretical estimations based on linear poroelasticity confirms the model's capacity in representing reservoir background stress responses. However, the study reveals that relying solely on background stress states can underestimate or overestimate fault reactivation potential, emphasizing the importance of including localized stress perturbations such as differential compaction and stress redistribution. Applied to a fault (M1) inspired by the geological characteristics of the Groningen field, the model shows slip initiation at 2965 m depth with 16.0 MPa depletion, aligning with field observations where seismicity occurred at approximately 3 km depth after 15.8 MPa depletion. Parametric studies reveal: (1) inelastic reservoir compaction delays fault reactivation and mitigates fault slip by reducing stress concentration, (2) higher intermediate in-situ stress magnitudes decrease the Coulomb Failure Stress (CFS) increase rate and reduce fault slip, (3) larger fault offsets amplify shear stress near the offset zone, promoting earlier reactivation and longer rupture propagation, and (4) fault permeability significantly influences pressure diffusion, with low-permeability faults leading to sharper stress changes and earlier fault destabilization. These insights highlight the critical role of geological and mechanical parameters in fault reactivation and provide a predictive framework for mitigating induced seismicity risks.

Coupled geomechanical modeling↗
DOE OSTI2016

A measure of plastic anisotropy for hexagonal close packed metals: Application to alloying effects on the formability of Mg

Mg is inherently plastically anisotropic and, over the years, alloying development efforts have sought to reduce the plastic anisotropy in order to enhance formability. To understand the relationship between alloy type and plastic anisotropy, we use a visco-plastic self-consistent (VPSC) polycrystal plasticity model to relate the macroscopic constitutive response to the underlying slip and twinning mechanisms in pure Mg and several Mg alloys. In the calculations, the influence of alloy type is represented by the differences in the CRSS values among the basal, prismatic, pyramidal slip and tensile twin systems. We show that for the same initial texture, this microscopic-level CRSS anisotropy can have a significant effect on the macroscopic indicators of formability, namely the anisotropy of the post-deformation polycrystal yield surface, tension-compression yield asymmetry, and Lankford coefficients. A plastic anisotropy (PA) measure is formulated to quantify the degree of single crystal plastic anisotropy acquired by the dissimilarities in the CRSS values of the slip and twinning modes for a given alloy. We demonstrate a strong correlation between the PA measure with the formability indicators mentioned above for multiple initial textures commonly enountered in processing. In conclusion, we find that alloys can be classified into two groups, those with a PA value below 2, which are more formable, less twinnable, and less sensitive to initial texture, where PA ~2 for pure Mg, and those with a PA value above 2, which possess the opposite deformation response.

36 MATERIALS SCIENCE↗
DOE OSTI2017

A dislocation density-based continuum model of the anisotropic shock response of single crystal α-cyclotrimethylene trinitramine

Here, we have developed a model for the finite deformation thermomechanical response of α-cyclotrimethylene trinitramine (RDX). Our model accounts for nonlinear thermoelastic lattice deformation through a free energy-based equation of state developed by Cawkwell et al. (2016) in combination with temperature and pressure dependent elastic constants, as well as dislocation-mediated plastic slip on a set of slip systems motivated by experimental observation. The kinetics of crystal plasticity are modeled using the Orowan equation relating slip rate to dislocation density and the dislocation velocity developed by Austin and McDowell (2011), which naturally accounts for transition from thermally activated to dislocation drag limited regimes. Evolution of dislocation density is specified in terms of local ordinary differential equations reflecting dislocation–dislocation interactions. This paper presents details of the theory and parameterization of the model, followed by discussion of simulations of flyer plate impact experiments. Impact conditions explored within this combined simulation and experimental effort span shock pressures ranging from 1 to 3 GPa for four crystallographic orientations and multiple specimen thicknesses. Simulation results generated using this model are shown to be in strong agreement with velocimetry measurements from the corresponding plate impact experiments. Finally, simulation results are used to motivate conclusions about the nature of dislocation-mediated plasticity in RDX.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Particle rotations and energy dissipation during mechanical compression of granular materials

Here, we present new in-situ measurements of particle rotations and energy dissipation during compression of 3D packings of stiff, frictional particles. Two confined, uniaxial compression tests with different degrees of lateral confinement are discussed. X-ray computed tomography and 3D X-ray diffraction were combined to provide inter-particle forces, slip and roll distances, twist angles, and energy dissipation at all inter-particle contacts. Each of these measured quantities followed exponential distributions above their respective mean values and power-law distributions below their mean values in both experiments. Changes in these distributions during experiments suggest that the quantities generally became more homogeneous with increasing overall sample stress. Contact roll and slip distances, twist angles, and energy dissipation were all more heterogeneous than inter-particle normal force magnitudes in both experiments. Energy dissipation due to inter-particle slipping accounted for 95% of the total energy dissipated in both experiments. Dissipation mechanisms at inter-particle contacts bearing more than the mean normal force were responsible for approximately 70% of each sample’s dissipated energy at each load step, even though these contacts constituted approximately 40% of the total number of contacts.

36 MATERIALS SCIENCE↗
DOE OSTI2019

A phase field model for dislocations in hexagonal close packed crystals

In this work, an application of a phase field formulation suitable for modeling the motion of individual partial and full dislocations in hexagonal close packed (HCP) crystals is presented. The formulation incorporates periodic potentials for glide on the distinct HCP slip systems, which are informed here by density functional theory (DFT). The model is applied to simulate the dissociation process starting from an unstable perfect dislocation and ending at its final equilibrium structure for different slip planes and in different HCP metals. The structural characteristics that are predicted for these dislocations include the partial Burgers vectors, dissociation distances, core widths of the partials, and any asymmetries in these quantities. Mg is selected as one of the model materials since its dislocations are the most well studied and it is nearly elastically isotropic. For Mg, it is shown that the predictions for dissociation distances agree with those reported previously by atomic-scale calculations, including density functional theory, for dislocations on the basal < a >, prismatic < a >, and pyramidal type II slip systems. Furthermore, phase field model results are also presented for dislocations in Ti and Zr, which we find develop distinctively different equilibrium structures than Mg.

36 MATERIALS SCIENCE↗
DOE OSTI2021

On the implementation of dislocation reactions in continuum dislocation dynamics modeling of mesoscale plasticity

The continuum dislocation dynamics framework for mesoscale plasticity is intended to capture the dislocation density evolution and the deformation of crystals when subjected to mechanical loading. It does so by solving a set of transport equations for dislocations concurrently with crystal mechanics equations, with the latter being cast in the form of an eigenstrain problem. Incorporating dislocation reactions in the dislocation transport equations is essential for making such continuum dislocation dynamics predictive. A formulation is proposed to incorporate dislocation reactions in the transport equations of the vector density-based continuum dislocation dynamics. This formulation aims to rigorously enforce dislocation line continuity using the concept of virtual dislocations that close all dislocation loops involved in cross slip, annihilation, and glissile and sessile junction reactions. The addition of virtual dislocations enables us to accurately enforce the divergence free condition upon the numerical solution of the dislocation transport equations for all slip systems individually. A set of tests were performed to illustrate the accuracy of the formulation and the solution of the transport equations within the vector density-based continuum dislocation dynamics. Comparing the results from these tests with an earlier approach in which the divergence free constraint was enforced on the total dislocation density tensor or the sum of two densities when only cross slip is considered shows that the new approach yields highly accurate results. Bulk simulations were performed for a face centered cubic crystal based on the new formulation and the results were compared with discrete dislocation dynamics predictions of the same. The microstructural features obtained from continuum dislocation dynamics were also analyzed with reference to relevant experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2014

Faulting processes in active faults - Evidences from TCDP and SAFOD drill core samples

The microstructures, mineralogy and chemistry of representative samples collected from the cores of the San Andreas Fault drill hole (SAFOD) and the Taiwan Chelungpu-Fault Drilling project (TCDP) have been studied using optical microscopy, TEM, SEM, XRD and XRF analyses. SAFOD samples provide a transect across undeformed host rock, the fault damage zone and currently active deforming zones of the San Andreas Fault. TCDP samples are retrieved from the principal slip zone (PSZ) and from the surrounding damage zone of the Chelungpu Fault. Substantial differences exist in the clay mineralogy of SAFOD and TCDP fault gouge samples. Amorphous material has been observed in SAFOD as well as TCDP samples. In line with previous publications, we propose that melt, observed in TCDP black gouge samples, was produced by seismic slip (melt origin) whereas amorphous material in SAFOD samples was formed by comminution of grains (crush origin) rather than by melting. Dauphiné twins in quartz grains of SAFOD and TCDP samples may indicate high seismic stress. The differences in the crystallographic preferred orientation of calcite between SAFOD and TCDP samples are significant. Microstructures resulting from dissolution–precipitation processes were observed in both faults but are more frequently found in SAFOD samples than in TCDP fault rocks. As already described for many other fault zones clay-gouge fabrics are quite weak in SAFOD and TCDP samples. Clay-clast aggregates (CCAs), proposed to indicate frictional heating and thermal pressurization, occur in material taken from the PSZ of the Chelungpu Fault, as well as within and outside of the SAFOD deforming zones, indicating that these microstructures were formed over a wide range of slip rates.

Janssen, C.↗
DOE OSTI2022

Relationships between fault characteristics and seismic responses in a large lab-scale tri-axial injection test conducted on a faulted Castlegate Sandstone

Here to investigate mechanisms causing microseismicity (M w < 2) at a CO 2 injection site, a large-scale triaxial block experiment was carried out on a faulted (saw-cut) cubic-meter of Castlegate Sandstone. The experiment consisted of injection tests at varying differential stresses, while monitoring and recording pore pressure and acoustic emissions (AEs). During the experiment, ~33,000 AEs and ~14 mm of horizontal displacement/slip, like a strike-slip fault movement, occurred. To understand the AE responses and ascertain fault characteristics near the located AEs, we modeled the topography of the fault surface, fault aperture, and fault-gouge thickness using pre- and post-experiment laser scans of the fault surface on each half of the block. Additionally, we characterized surface roughness parallel and perpendicular to slip. Models show crushing and flattening of the fault surfaces can be linked to the spatiotemporal distribution of AEs within 50 mm of the fault surface. Approximately 65% of AEs were in areas with small aperture (≤300 μm); thicker fault gouge was observed in adjacent areas with wider aperture and shows a two-fold reduction in grain size relative to unaltered Castlegate Sandstone. This work provides a conceptual understanding on fault surface evolution, which can be applied towards modeling of seismic slip.

58 GEOSCIENCES↗
DOE OSTI2018

Effect of initial orientation on dynamic recrystallization of a zirconium alloy during hot deformation

Highlights: • The dynamic recrystallization process is enhanced by the operation of slip. • Continuous dynamic recrystallization is promoted by the rotation of grains. • Texture induced hardening hides the softening induced by dynamic recrystallization. - Abstract: The present study investigated the influence of the initial orientation on the dynamic recrystallization (DRX) behavior of a Zr-1Sn-0.3Nb alloy. A hot-rolled and annealed Zr sheet was compressed along two directions: along the normal direction so that the grains' -axis was nearly parallel to the loading direction (0° sample) and along the transverse direction so that the grains' -axis was nearly perpendicular to the loading direction (90° sample). The samples were compressed at 700 °C at a strain rate of 1 s{sup −1}. The microstructures at different strains were characterized by the electron backscatter diffraction (EBSD) technique, and conventional dislocation analysis using transmission electron microscope (TEM) was performed. A threshold value of grain orientation spread (GOS) equaled to 5° was used to distinguish the dynamically recrystallized grains from the deformed matrix. The results revealed that the DRX behavior strongly depended on the initial orientation. The Schmid factor analysis and TEM observation confirmed that pyramidal slip operated from the first stage of deformation in the 0° sample but not in the 90° sample. For the 0° sample, in the early and medium stages of deformation, due to the high stored energy caused by the operation of pyramidal slip, DDRX was mainly contributed to the formation of new fine grains. However, in the later stage of deformation, the DRX mechanism changed from DDRX to CDRX. In the 90° sample, although DDRX featured by grain boundary bulging occurred, the main DRX mechanism was CDRX in the whole deformation processing. Moreover, texture induced hardening in the early stage of deformation hides the softening induced by DDRX.

36 MATERIALS SCIENCE↗