Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “S MATRIX”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Microstructure and wear characterization of aluminum matrix composites reinforced with industrial waste fly ash particulates synthesized by friction stir processing

Fly ash (FA) is a waste product of coal combustion in thermal power plants which is available in massive quantities all over the world causing land pollution. This paper reports the characterization of AA6061 aluminum matrix composites (AMCs) reinforced with FA particles synthesized using friction stir processing (FSP). The volume fraction of FA particles was varied from 0 to 18 in steps of 6. The prepared AMCs were characterized using optical microscopy (OM), scanning electron microscopy (SEM) and electron backscattered diagram (EBSD). The wear rate was estimated using a pin-on-disc wear apparatus. FA particles were observed to be distributed homogeneously in the AMC irrespective of the location within the stir zone. The EBSD micrographs revealed remarkable grain refinement in the AMC. The incorporation of FA particles enhanced the microhardness and wear resistance of the AMC. The strengthening mechanisms of the AMC were discussed and correlated to the observed microstructures. The wear mechanisms were identified by characterizing the wear debris and worn surfaces. - Highlights: •Industrial waste fly ash was used to produce aluminum matrix composites. •Friction stir processing was used to produce AA6061/Fly Ash composite. •Fly ash particles refined the grains of aluminum matrix. •Fly ash particles enhanced the hardness and wear resistance. •Successful utilization of fly ash to make aluminum composites reduces land pollution.

36 MATERIALS SCIENCE↗

Microstructure and microhardness of an Al-6061 metal matrix composite processed by high-pressure torsion

Disks of an Al-6061 metal matrix composite, reinforced with 10 vol.% Al{sub 2}O{sub 3} particles, were processed by high-pressure torsion (HPT) at room temperature for 1/4, 1/2, 1, 5 and 10 turns under an applied pressure of 6.0 GPa. The evolution of microstructure was investigated using optical microscopy and scanning electron microscopy. During HPT processing the average grain size within the aluminum matrix decreased from ∼ 35 μm in the unprocessed condition to ∼ 170 nm after processing through 10 turns but there was no significant effect on the size and distribution of the alumina particulate clusters. The values of the Vickers microhardness were recorded across the surface of each disk and then plotted as two-dimensional and three-dimensional color-coded contour maps. The results show the hardness increases from ∼ 56 Hv in the initial condition to ∼ 165 Hv after HPT for 10 turns. The results demonstrate that, as in many unreinforced metallic alloys, the evolution of hardness with strain exhibits strain hardening without any significant recovery. - Highlights: •The average grain size of the Al matrix was ~ 170 nm after processing for 10 turns. •No significant effect of HPT on the size and distribution of the Al{sub 2}O{sub 3} particles. •The evolution of microhardness demonstrates strain hardening without recovery. •The microhardness at low strains increases linearly from the center to the edge. •The microhardness at high strains becomes homogeneous with a saturation of ~ 170 Hv.

36 MATERIALS SCIENCE↗

Microstructure evolution and properties of graphene nanoplatelets reinforced aluminum matrix composites

Highlights: • Lamellar structure of GNPs fibers and Al matrix was obtained in the rolling direction. • Stacking faults were observed in Al grains due to greatly increased GNPs/Al interfaces. • Strength of Al-0.2 wt% GNPs increased 36.8% with negligible electrical conductivity loss. - Abstract: Aluminum matrix composites reinforced with graphene nanoplatelets (GNPs) were prepared by continuous casting and subsequent rolling. Al-GNPs master alloy, prepared by ball milling and cold pressing, was added into Al melts to fabricate the composites. Microstructure evolution of the composites were observed using scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electron back scattered diffraction (EBSD). GNPs distributed uniformly in the as-cast specimen and then transformed into fibers in the rolling direction after deformation and finally a lamellar structure formed in the composites. Raman spectra showed that the structural damage of GNPs mainly came from ball milling. The interface between GNPs and Al was well combined in general while a few microcracks were observed, which reduced the ductility of the composites and no adverse aluminum carbide (Al{sub 4}C{sub 3}) was detected at the interface. Stacking faults were observed interior of the aluminum grain, which may due to the existence of plentiful interface introduced by GNPs. Fracture observation revealed that the load transferred from Al matrix to GNPs. The ultimate tensile strength of Al-0.2 wt% GNPs composites was about 36.8% higher than that of pure Al with the same casting and rolling process, which should result from the lamellar structure and load transfer, while the conductivity of the composites decreased slightly, indicating that interface scattering between Al and GNPs is very limited. The investigation results show that Al-GNPs composite is potential for high strength and high conductivity application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Mapping the Microhardness of Al Matrix in U-7Mo/Al Dispersion Fuels at Medium and High Burn-up by in situ Nanoindentation

The mechanical degradation of the Al matrix in U-7Mo dispersion fuels was detected after irradiation in previous studies, but more details of the degradation mechanism are not clear yet to clarify the root cause. In this study, microhardness mapping in fresh and irradiated U-7Mo dispersion fuels coated with ZrN, with burn-up of 3.35 × 10 21 and 6.28 × 10 21 f/cm 3 , are measured to reveal the hardening of the Al matrix as a function of distance to fuel particles. Micro cubes were pulled by plasma focused ion beam scanning electron microscopy and tested by in situ nanoindenter with Berkovitch tip. Size effects are measured in medium and high burn-up samples. The higher burn-up specimen exhibits a more pronounced size effect when indent load is lower than 20 mN. Size effect correction models are also calculated by plots fitting, which predicts the true microhardness without size effect. Results shows that the hardness of the Al matrix near the ZrN coating has the highest value, then decreases moving away from the coating and become stable when the distance reaches ∼10 µm. The hardness starts increasing again getting closer to the next fuel particle, which makes the hardness distribution between two fuel particles to be “U” shape.

36 - MATERIALS SCIENCE↗

Incorporation of Er{sup 3+} ions into an amorphous matrix of Cd{sub 2}V{sub 2}O{sub 7} containing crystalline CdO nanoparticles

Er{sup 3+} ions have been introduced into a matrix of Cd{sub 2}V{sub 2}O{sub 7} using a conventional melt-quenching method. X-ray diffraction results indicate that a material constituted of CdO nanocrystals of ∼40 nm embedded within the amorphous Cd{sub 2}V{sub 2}O{sub 7} matrix was fabricated. The presence of such nanocrystals was confirmed by transmission electron microscopy. Raman spectroscopy measurements confirm that the amorphous matrix is composed by Cd{sub 2}V{sub 2}O{sub 7}. The band gap obtained by optical absorption is 2.84 eV. From the photoluminescence spectrum the electronic transitions such as ({sup 2}H{sub 11/2}, {sup 4}S{sub 3/2}, {sup 4}F{sub 9/2}, {sup 4}I{sub 9/2}) → {sup 4}I{sub 15/2} and {sup 4}S{sub 3/2} → {sup 4}I{sub 13/2} corresponding to Er{sup 3+} were observed. Thermally activated transport was observed by dark conductivity measurements taken from room temperature to 450 K. The morphology and chemical composition of the sample were determined by scanning electron microscopy and energy dispersive spectroscopy, respectively.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Ultem((R))/ZIF-8 mixed matrix hollow fiber membranes for CO2/N-2 separations

Organic-inorganic hybrid (mixed matrix) membranes can potentially extend the separation performance of traditional polymeric materials while maintaining processing convenience. Although many dense films studies have been reported, there have been few reported cases of these materials being successfully extended to asymmetric hollow fibers. In this work we report the first successful production of mixed matrix asymmetric hollow fiber membranes containing metal-organic-framework (MOF) ZIF-8 fillers. Specifically, we have incorporated ZIF-8 into a polyetherimide (Ultem((R)) 1000) matrix and produced dual-layer asymmetric hollow fiber membranes via the dry jet-wet quench method. The outer separating layer of these composite fibers contains 13 wt% (17 vol%) of ZIF-8 filler. These membranes have been tested over a range of temperatures and pressures for a variety of gas pairs. An increase in separation performance for the CO2/N-2 gas pairs was observed for both pure gas and mixed gas feeds. (C) 2012 Elsevier B.V. All rights reserved.

Dai, Y↗

Analytical models of the strength and ductility of CNT reinforced metal matrix nano composites under elevated temperatures

Carbon nanotubes (CNTs) can greatly enhance the strength of metal matrix composites while resulting in ductility loss. This strength-ductility tradeoff dilemma always confines the development of material design and real-life applications. Here in this work, a temperature dependent strengthening analytical model is proposed for CNT reinforced metal matrix composites which considers three common strengthening mechanisms: Orowan looping effect, thermal expansion mismatch effect, and load bearing effect. The proposed model can predict composite material strength with different volume fractions of CNTs and under different temperatures. Combining the strengthening model with the stress based modified Mohr-Coulomb (sMMC) ductile fracture model, a ductility analytical model is then derived. This ductility analytical model includes the influences of temperature, multi-axial stress loading conditions, as well as the aforementioned three strengthening mechanisms. A good agreement has been achieved between literature published experimental data and analytical predictions for both composite material strength and ductility loss. The proposed two analytical models can provide a straightforward way to study the strength-ductility relationship for CNT reinforced metal matrix composites over a wide range of temperatures and different stress states, and then provide guidance on new material design and processing.

36 MATERIALS SCIENCE↗

UV/IR symmetries of the S -matrix and RG flow

The low energy S-matrix which describes non-relativistic scattering arising from finite-range forces has UV/IR symmetries that are hidden in the corresponding effective field theory (EFT) action. Furthermore, it is shown that the S-matrix symmetries are manifest as geometric symmetries of the RG flow of coupling constants in the EFT action in both three and two spatial dimensions. An example is given demonstrating that UV/IR symmetry breaking in the S-matrix implies strong constraints on the RG flow of the coefficients of the corresponding symmetry-breaking operators in the EFT.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

First measurement of polarized spin-density matrix elements and differential cross sections dσ/dt in ω photoproduction off the proton for 2.7 < Eγ < 5.2 GeV using CLAS at Jefferson Lab

We report on the differential cross sections dσ/dt, the unpolarized spin-density matrix elements ρ 00 0 , ρ 1 − 1 0 , Re ρ 10 0 , and the first extraction of the polarized elements Im ρ 10 3 , Im ρ 1 − 1 3 for the reaction γp → pω using the CLAS spectrometer at Jefferson Laboratory. The ω mesons were detected in their dominant charged decay mode, ω → π + π − π 0 , and all t-dependent results are presented in a fine binning for incident photon energies between 2.73 and 5.16 GeV (corresponding to the center-of-mass energy range W ∈ [ 2.45, 3.25 ] GeV). All matrix elements are first measurements for − t > 0.6 GeV2. Moreover, differential cross sections dσ/d(cos Θ c . m . ω ) and the corresponding angle-dependent unpolarized spin-density matrix elements in the Adair frame are presented for the incident photon energy range 1.56–3.80 GeV (corresponding to W ∈ [ 1.95, 2.83 ] GeV). These new ω photoproduction data are consistent with earlier CLAS results but extend the energy range well beyond the nucleon resonance region into the Regge regime. The comparison with Regge-theory-based model predictions shows that the new data impose more stringent constraints on our understanding of ω photoproduction.

Hu, T.↗

Ionic cross-linked polyether and silica gel mixed matrix membranes for CO 2 separation from flue gas

Mixed matrix membranes (MMMs) were prepared by incorporating 10 wt%, 20 wt% and 30 wt% silica gel filler particles into novel ionic cross-linked polyether (IXPE) polymers. Porous silica gel has the advantage of high surface area that can increase the free volume and permeability in a polymer film while also being commercially available and low cost. The MMMs featured high chemical and thermal stability as well as a modest improvement in storage modulus. These features are due to the excellent interfacial interaction between silica gel filler particles and the polymer matrix. Increasing the loading of silica gel particles in MMMs resulted in higher permeability up to 120 Barrer for CO 2 , which is about 40% higher than the neat polymer matrix. Finally, most importantly, the MMMs maintained a very high CO 2 /N 2 selectivity performance of around 41 for all particle loadings that were tested.

36 MATERIALS SCIENCE↗

Deletions in the fifth alpha helix of HIV-1 matrix block virus release

The matrix (MA) protein of HIV-1 is the N-terminal component of the Gag structural protein and is critical for the early and late stages of viral replication. MA contains five α-helices (α1–α5). Deletions in the N-terminus of α5 as small as three amino acids impaired virus release. Electron microscopy of one deletion mutant (MA∆96-120) showed that its particles were tethered to the surface of cells by membranous stalks. Immunoblots indicated all mutants were processed completely, but mutants with large deletions had alternative processing intermediates. Consistent with the EM data, MA∆96-120 retained membrane association and multimerization capability. Co-expression of this mutant inhibited wild type particle release. Alanine scanning mutation in this region did not affect virus release, although the progeny virions were poorly infectious. Combined, these data demonstrate that structural ablation of the α5 of MA inhibits virus release. - Highlights: • Deletions were identified in the C-terminus of matrix that block virus release. • These deletion mutants still multimerized and associated with membranes. • TEM showed the mutant particles were tethered to the cell surface. • Amino acid mutagenesis of the region did not affect release. • The data suggests that disruption of matrix structure blocks virus release.

60 APPLIED LIFE SCIENCES↗

Extracellular matrix components direct porcine muscle stem cell behavior

In muscle tissue, extracellular matrix proteins, together with the vasculature system, muscle-residence cells and muscle fibers, create the niche for muscle stem cells. The niche is important in controlling proliferation and directing differentiation of muscle stem cells to sustain muscle tissue. Mimicking the extracellular muscle environment improves tools exploring the behavior of primary muscle cells. Optimizing cell culture conditions to maintain muscle commitment is important in stem cell-based studies concerning toxicology screening, ex vivo skeletal muscle tissue engineering and in the enhancement of clinical efficiency. We used the muscle extracellular matrix proteins collagen type I, fibronectin, laminin, and also gelatin and Matrigel as surface coatings of tissue culture plastic to resemble the muscle extracellular matrix. Several important factors that determine myogenic commitment of the primary muscle cells were characterized by quantitative real-time RT-PCR and immunofluorescence. Adhesion of high PAX7 expressing satellite cells was improved if the cells were cultured on fibronectin or laminin coatings. Cells cultured on Matrigel and laminin coatings showed dominant integrin expression levels and exhibited an activated Wnt pathway. Under these conditions both stem cell proliferation and myogenic differentiation capacity were superior if compared to cells cultured on collagen type I, fibronectin and gelatin. In conclusion, Matrigel and laminin are the preferred coatings to sustain the proliferation and myogenic differentiation capacity of the primary porcine muscle stem cells, when cells are removed from their natural environment for in vitro culture.

60 APPLIED LIFE SCIENCES↗

Modulation of Carrier Type in Nanocrystal-in-Matrix Composites by Interfacial Doping

Inorganic nanocomposites synthesized by combination of colloidal nanocrystals (NCs) and inorganic clusters have recently emerged as new materials with novel and unique functionalities. Much of the demonstrated promise of nanocomposites derives from the unique interactions between NC and matrix components—this generates new material properties, which direct unique transport behavior in the overall solid or nanocomposite—be it mass, charge, or heat. While measured empirically, it has remained largely impossible to take an a priori look at material properties and use those as a guideline to design desired transport behavior. Fundamentally, this is because the structural and electronic changes manifest at those interfaces have remained hidden from examination. We provide experimental evidence that transport behavior in nanocrystal-in-matrix (NIM) composites is dictated primarily by interfacial charge transfer associated with electronic and structural reconstructions as the composite forms. Our approach building continuous composite superlattices serves as a starting point for systematic probing of the nanointerface of NIM composites via ultrathin films. A combination of field effect transistor device characterization and photoemission spectroscopy reveals the systematic dependence of the polarity of charge transfer on the selection of matrix materials in NIM composites. We use this insight to combine, by design, different components to tune the carrier type in NIM composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Spin–Orbit Matrix Elements for a Combined Spin-Flip and IP/EA approach

We introduce a practical approach for computing the Breit–Pauli spin–orbit matrix elements of multiconfigurational systems with both spin and spatial degeneracies based on our recently developed RAS-nSF-IP/EA method (Houck, S. E.; et al. J. Chem. Theory Comput. 2019, 15, 2278). The spin–orbit matrix elements over all the multiplet components are computed using a single one-particle reduced density matrix as a result of the Wigner–Eckart theorem. A mean field spin–orbit approximation was used to account for the two-electron contributions. Basis set dependence as well as the effect of including additional excitations is presented. The effect of correlating the core and semicore orbitals is also examined. Surprisingly accurate results are obtained for spin–orbit coupling constants, despite the fact that the efficient wave function approximations we research neglect the bulk of dynamical correlation.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Density Matrix Implementation of the Fermi–Löwdin Orbital Self-Interaction Correction Method

The Fermi–Löwdin orbital self-interaction correction (FLOSIC) method effectively provides a transformation from canonical orbitals to localized Fermi–Löwdin orbitals which are used to remove the self-interaction error in the Perdew–Zunger (PZ) framework. This transformation is solely determined by a set of points in space, called Fermi–Löwdin descriptors (FODs), and the occupied canonical orbitals or the density matrix. In this work, we provide a detailed workflow for the implementation of the FLOSIC method for removal of self-interaction error in DFT calculations in an orbital-by-orbital basis that takes advantage of the unitary invariant nature of the FLOSIC method. In this way, it is possible to cast the self-consistent energy minimization at fixed FODs in the same manner than standard Kohn–Sham with one additional term in the Kohn–Sham Hamiltonian that introduces the PZ self-interaction correction. Each energy minimization iteration is divided in two substeps, one for the density matrix and one for the FODs. Expressions for the effective Kohn–Sham matrix and FOD gradients are provided such that its implementation is suitable for most electronic structure codes. Here, we analyze the convergence characteristics of the algorithm and present applications for the evaluation of NMR shielding constants and real-time time-dependent DFT simulations based on the Liouville–von Neumann equation to calculate excitation energies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Complementary Semiconducting Polymer Blends: The Influence of Conjugation-Break Spacer Length in Matrix Polymers

The concept of complementary semiconducting polymer blends ( c -SPBs) for efficient charge transport was recently proposed and established by our group. In this study, we aim to reveal the influence of the length of conjugation-break spacers (CBSs) on charge transport properties of the matrix polymers and their corresponding complementary polymer blends. A series of 11 DPP-based semiconducting polymers DPP-C m ( m = 2–12) that incorporate CBSs of 2–12 methylene units along the polymer backbones were prepared and characterized. The UV–vis spectra and the ultraviolet photoelectron spectroscopy (UPS) measurements show that the CBS length has marginal influence on the polymer absorption spectra, energy levels, and band gaps. It also has little impact on polymer decomposition temperatures. However, the CBS length has a profound influence on polymer phase transition and the heat of fusion. As for the melt transitions, an odd–even effect is observed from DPP-C2 to DPP-C7, in which polymers with even-numbered CBSs show higher melting points than their adjacent odd-numbered derivatives. We note the trend is opposite for heat of fusion. The polymers with odd-numbered CBSs exhibit larger heat of fusion, indicating higher ordering and crystallinity. The odd–even effect is also found in surface morphologies of the polymers by atomic force microscopy (AFM). The polymers with the even CBSs have a more interconnected feature that appear more fibrillar than the polymers with the odd linkages. As far as charge carrier mobility is concerned, the average number drops from 0.023 cm 2 V –1 s –1 to 7.9 × 10 –6 cm 2 V –1 s –1 as the CBS moves from C2 to C12. It is intriguing to observe that even-numbered polymers outperform the adjacent odd-numbered polymers, despite the fact that the latter show higher ordering and crystallinity in thin films. When these polymers are mixed with fully conjugated DPP-C0 (2 wt %, designated as tie chain polymer), the obtained c -SPBs witness a dramatic increase (2–4 orders of magnitude) in charge carrier mobility. Interestingly, the odd–even effect is not found for charge transport in the c -SPBs. This work reveals that the length of CBSs plays a significant role in charge transport properties of the matrix polymers and reconfirms that efficient charge transport properties of the c -SPB result from the interactions between matrix polymers and tie chain polymers. This begins to provide guidelines as to what spacer lengths may be utilized to offer the best balance between processing and charge transport properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Binary Cation Matrix Electrolyte and Its Effect on Solid Electrolyte Interphase Suppression and Evolution of Si Anode

An unstable solid electrolyte interphase (SEI) has been recognized as one of the biggest challenges to commercializing silicon (Si) anodes for high-energy-density batteries. This work thoroughly investigates a binary cation matrix of Mg 2+ +Li + electrolyte and its role in SEI development, suppression, and evolution of a Si anode. Findings demonstrate that introducing Mg ions dramatically reduces the SEI growth before lithiation occurs, primarily due to the suppression of solvent reduction, particularly ethylene carbonate (EC) reduction. The Mg 2+ alters the Li + cation solvation environment as EC preferably participates in the oxophyllic Mg 2+ solvation sheath, thereby altering the solvent reduction process, resulting in a distinct SEI formation mechanism. The initial SEI formation before lithiation is reduced by 70% in the electrolyte with the presence of Mg 2+ cations. While the SEI continues to develop in the postlithiation, the inclusion of Mg ions results in an approximately 80% reduction in the postlithiation SEI growth. Continuous electrochemical cycling reveals that Mg 2+ plays a crucial role in stabilizing the deep-lithiated Si phases, which effectively mitigates side reactions, resulting in controlled SEI growth and stable interphase while eliminating complex Li x Si y formation. Mg ions promote the development of a notably more rigid and homogeneous SEI, characterized by a reduced dissipation (ΔD) in the Mg 2+ +Li + ion matrix compared to the solely Li + system. In conclusion, this report reveals how the Mg 2+ +Li + ion matrix affects the SEI evolution, viscoelastic properties, and electrochemical behavior at the Si interface in real time, laying the groundwork for devising strategies to enhance the performance and longevity of Si-based next-generation battery systems.

25 ENERGY STORAGE↗

Confining Sulfur Species in Cathodes of Lithium–Sulfur Batteries: Insight into Nonpolar and Polar Matrix Surfaces

To alleviate the polysulfides shuttle effect in lithium–sulfur batteries (LSBs), the use of a functionalized carbon matrix with a polar surface has been widely reported to chemically bind the soluble polysulfides. However, whether and how such a polar carbon surface affects the overall cathode performance, particularly the initial discharge corresponding to the reduction of cyclooctasulfur (S8), has not caught enough attention. By combining polar and nonpolar carbon matrix surfaces in different configurations through sandwiching sulfur species between two carbon matrix membranes, we found cells with dramatically different performance. The discharge process at different states, particularly the charge-transfer resistances corresponding to nonpolar S8 and polar polysulfide intermediates and the final Li2S, were investigated. The experimental results, further supported by first-principles density functional theory calculations, indicate that the adsorption energy and barrier for electron transfer together affect the electrochemical performance of LSBs, and therefore, a rational design that combines polar and nonpolar surfaces should be adopted.

Li, Shiqi↗