Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Response of some Thematic Mapper band ratios to variation in soil water content

Bidirectional reflectance to nadir in the reflective TM bands and the 1.15-1.3-micron band was measured in the laboratory as moisture content was varied in ten soils. Stronger absorption by water in TM5 and TM7 was expected to cause ratios of other bands to TM5 and TM7 to increase with water content, but in most cases these ratios were constant or decreased at low to intermediate water content and increased only at high moisture levels. Because these ratios were found to decrease as illumination elevation angle decreased, it was suggested that increased roughness resulting from the methods of moistening and mixing the soil may have tended to counteract the expected ratio increases.

Musick, H. Brad↗

Axial ratios and orientations for 100 Galactic globular star clusters

Axial ratios and major-axis orientations determined from image processing of Palomar and SRC Sky Survey material are tabulated for a sample of 100 Galactic globular clusters. From a subsample of 99 clusters, the mean axial ratio is found to be 0.93 + or - 0.01. Given that only 32 percent are flatter than b/a less than 0.9, and 5 percent flatter than 0.8, the clusters are found to be quite spherical. As predicted by King (1961 and 1966), tidal interactions by the Galaxy on the cluster are not the means by which the observed ellipticities are produced. Rather, Galactic absorption effects may have a moderate but not dominant effect on the clusters' observed ellipticities, as suggested by van den Bergh (1984). The alternate mechanisms of cluster rotation or anisotropic internal velocity distributions, or both, are considered to be more likely. The observed distribution of axial ratios is statistically indistinguishable from that of a similar-size sample of rotationally flattened clusters, which have axial-ratio values lying in the range of 0.75 less than b/a less than 0.83, and the major axes of which are oriented randomly in space.

White, Raymond E.↗

The C-12/C-13 isotope ratio of the interstellar medium in the neighborhood of the sun

Data from observations of Xi Per, P Cyg, 20 Tau, and 23 Tau, obtained at 4232 and 3957 A using a coude spectrograph and a 1872-element reticon on the 3-m Shane telescope at Lick Observatory during 1984-1985, are combined with data on Zeta Oph (Hawkins et al., 1985) and used to estimate the C isotope ratio of the ISM near the sun. The results are presented in extensive tables and graphs and characterized in detail. The (C-12)H(+)/(C-13)H(+) abundance ratios toward the five stars are found to agree to within 12 percent and shown to be representative of the C-12/C-13 ratios in the gas, strongly indicating that the local ISM is homogeneous. The difference between the ISM ratio (43 + or - 4) and the solar-system value (89) is attributed to the chemical evolution of the ISM in the 4.9 Gyr since the formation of the sun.

Hawkins, Isabel↗

Directed band ratioing for the retention of perceptually-independent topographic expression in chromaticity-enhanced imagery

A band ratioing method is developed which directs the retention of topographic expression and albedo information so that they remain depicted as prominent variations in image intensity. Band data are adjusted so that ratio values for each surface material coherently increase with increasing pixel bispectral radiance for all three ratios of the color composite. The retained topographic expression and albedo information do not significantly distort the ratio-enhanced band-variant reflectance information, and the resultant images are similar to chromaticity-enhanced band composite images, but require only simple arithmetic processing steps.

Crippen, Robert E.↗

Computer-aided design of high-contact-ratio gears for minimum dynamic load and stress

A computer aided design procedure is presented for minimizing dynamic effects on high contact ratio gears by modification of the tooth profile. Both linear and parabolic tooth profile modifications of high contact ratio gears under various loading conditions are examined and compared. The effects of the total amount of modification and the length of the modification zone were systematically studied at various loads and speeds to find the optimum profile design for minimizing the dynamic load and the tooth bending stress. Parabolic profile modification is preferred over linear profile modification for high contact ratio gears because of its lower sensitivity to manufacturing errors. For parabolic modification, a greater amount of modification at the tooth tip and a longer modification zone are required. Design charts are presented for high contact ratio gears with various profile modifications operating under a range of loads. A procedure is illustrated for using the charts to find the optimum profile design.

Lin, Hsiang Hsi↗

The gas/dust ratio in spiral galaxies

IRAS data are used here to calculate warm dust masses, which are then compared with the molecular and atomic gas masses for 58 spiral galaxies in order to constrain the fraction and the phase of the interstellar medium in spiral galaxies that contributes to the emission measured by IRAS. The dispersion in the ratio of dust mass to total gas mass is larger than expected on the basis of measurement errors. The dispersion in the ratio of dust mass to inner disk gas mass is less than the dispersion in the ratio of IR to radio emission. The inner gas to warm dust mass ratio for spiral galaxies is 1080 + or - 70, indicating that 80-90 percent of the dust mass in spiral galaxies is radiating at over 100 microns and has a temperature less than about 30 K. However, the bulk of the dust in spiral galaxies is less than about 15 K regardless of the phase of the ISM. Both H I and H2-associated dust contributes to the warm 30 K emission.

Devereux, Nicholas A.↗

High-resolution CO observations of luminous infrared galaxies with large L(ir)/L(B) ratios - IRAS 10173 + 0828, Zw 049.057, IRAS 17208 - 0014

The Owens Valley mm-wave interferometer has been used for high-resolution (about 3-7 arcsec) mapping of CO emission in three luminous IRAS galaxies: IRAS 17208 - 0014, 15107 + 0724, and IRAS 10173 + 0828. These galaxies are among the most extreme, in terms of their L(ir)/L(B) ratio, for objects in the IRAS Bright Galaxy Surveys. The CO emission detected in the three galaxies originates from a single region centered on the IRAS emission peak. These observations have shown that these galaxies have similar values for the global L(ir)/M(H2) ratio, for the surface density of molecular gas in their central regions and for the extinction toward the nucleus (above 300 mag). A high L(ir)/L(B) ratio seems to be a good predictor for both a high global L(ir)/M(H2) ratio and very large central H2 surface densities.

Planesas, P.↗

Molecular hydrogen in the vicinity of NGC 7538 IRS 1 and IRS 2 - Temperature and ortho-to-para ratio

Near-infrared spectroscopic observations of the active star-forming region near NGC 7538 IRS 1 and IRS 2 were made. The relative intensities of the v = 1-0 Q(1), Q(3), and Q(5) lines of molecular hydrogen are used to calculate a rotational excitation temperature. Comparison of the measured intensity of the Q(2) transition relative to the intensity of Q(1) and Q(3) permitted the retrieval of the ratio of ortho-to-para hydrogen. It is found that an ortho-to-para ratio of between 1.6 and 2.35 is needed to explain the Q-branch line intensity ratios, depending on the excitation model used. This range in ortho-to-para ratios implies a range of molecular hydrogen formation temperature of approximately 105 K to 140 K.

Hoban, Susan↗

A statistical study of high coronal densities from X-ray line-ratios of Mg XI

An X-ray line-ratio density diagnostic was applied to 50 Mg XI spectra of flaring active regions on the sun recorded by the Flat Crystal Spectrometer on the SMM. The plasma density is derived from R, the flux ratio of the forbidden to intercombination lines of the He-like ion, Mg XI. The R ratio for Mg XI is only density sensitive when the electron density exceeds a critical value (about 10 to the 12th/cu cm), the low-density limit (LDL). This theoretical value of the low-density limit is uncertain as it depends on complex atomic theory. Reported coronal densities above 10 to the 12th/cu cm are uncommon. In this study, the distribution of R ratio values about the LDL is estimated and the empirical values are derived for the 1st and 2nd moments of this distribution from 50 Mg XI spectra. From these derived parameters, the percentage of observations is derived which indicated densities above this limit.

Linford, G. A.↗

Stratospheric Backscatter, Extinction, and Lidar Ratio Profiling After the Mt. Pinatubo Eruptions

Since August 1991 the stratospheric aerosol layer is continuously monitored with a combination Raman elastic-backscatter lidar, groundbased systems. XeCl excimer laser is used as the radiation source. Signals elastically backscattered from air molecules and particles and inelastically Raman backscattered from nitrogen molecules are detected. The measurements of these two signal profiles up to 35 km height allows the separate and independent determination of aerosol extinction and backscatter properties in the perturbed lower stratosphere. The extinction coefficient is derived from the nitrogen Raman signal profile, while the backscatter coefficient is obtained from the elastic-to-inelastic backscatter signal ratio. In this way, also the extinction-to-backscatter, or lidar, ratio profile is determined. For the first time, lidar ratios are determined in the perturbed stratospheric layer by the use of remote sensing only. The lidar ratio contains information about the size range of the stratospheric particles which are assumed to be sulfuric acid droplets, and it is needed in the calculation of aerosol optical properties from data taken with a typical backscatter lidar.

Ansmann, Albert↗

The interstellar deuterium-to-hydrogen ratio - A reevaluation of Lyman absorption-line measurements

The D/H ratio in the local interstellar medium is evaluated based upon previously published measurements of Lyman absorption lines together with the hypothesis that the D/H ratio is constant. A unique value for the D/H ratio of 1.5 (+/- 0.2) x 10 exp -5 by number is shown to be consistent with all published determinations made with the Copernicus and the International Ultraviolet Explorer satellites. The possibility that the D/H ratio may vary substantially in the local interstellar medium is considered and found to be unnecessary.

Mccullough, Peter R.↗

The Interference Effects of a Body on the Spanwise Load Distributions of Two 45 Degree Sweptback Wings of Aspect Ratio 8.02 from Low-Speed Tests

Tests of two wing-body combinations have been conducted in the Langley 19-foot pressure tunnel at a Reynolds number of 4 x 10(exp 6) and a Mach number of 0.19 to determine the effects of the bodies on the wing span load distributions. The wings had 45 degrees sweepback of the quarter-chord line, aspect ratio 8.02, taper ratio 0.45, and incorporated 12-percent-thick airfoil sections streamwise. One wing was untwisted and uncambered whereas the second wing incorporated both twist and camber. Identical bodies of revolution, of 10:1 fineness ratio, having diameter-to-span ratios of 0.10, were mounted in mid-high-wing arrangements. The effects of wind incidence, wing fences, and flap deflection were determined for the plane uncambered wing. The addition of the body to the plane wing increased the exposed wing loading at a given lift coefficient as much as 10 percent with the body at 0 degrees incidence and 4 percent at 4 degrees incidence. The bending-moment coefficients at the wing-body juncture were increased about 2 percent with the body at 0 degrees incidence, whereas the increases were as much as 10 percent with the body at 4 degrees incidence. The spanwise load distributions due to the body on the plane wing as calculated by using a swept-wing method employing 19 spanwise lifting elements and control points generally showed satisfactory agreement with experiment. The spanwise load distributions due to body on the flapped plane wing and on the twisted and cambered wing were dissimilar to those obtained on the plane wing. Neither of the methods of calculation which were employed yielded distributions that agreed consistently with experiment for either the flapped plane wing or the twisted and cambered wing.

Martina, Albert P.↗

Non-linear properties of metallic cellular materials with a negative Poisson's ratio

Negative Poisson's ratio copper foam was prepared and characterized experimentally. The transformation into re-entrant foam was accomplished by applying sequential permanent compressions above the yield point to achieve a triaxial compression. The Poisson's ratio of the re-entrant foam depended on strain and attained a relative minimum at strains near zero. Poisson's ratio as small as -0.8 was achieved. The strain dependence of properties occurred over a narrower range of strain than in the polymer foams studied earlier. Annealing of the foam resulted in a slightly greater magnitude of negative Poisson's ratio and greater toughness at the expense of a decrease in the Young's modulus.

Choi, J. B.↗

The (C-12)O/(C-13)O ratio toward Zeta Ophiuchi

A tentative detection of the J = 1 - 0 emission line of (C-13)O has been obtained with SEST from a 24.4 hour integration. The velocity resolution used was 0.23 km/s and the FWHP beamwidth was 45 arcsec. If the (C-13)O line data are conservatively interpreted as an upper limit, the (C-12)O/(C-13)O ratio is not less than 60. Our result supports the previous determination of a large value of the isotope ratio in this cloud, made using radio emission lines with a 1.6-arcmin beam, and extends the ratio based on emission lines to a smaller region. When interpreted as a lower limit, our data is consistent with the ratio obtained from UV absorption line data for (C-12)O and (C-13)O.

Wilson, T. L.↗

Effect of pressure ratio and inlet pressure on performance of experimental gas turbine at inlet temperature of 800 R

An experimental gas turbine was operated over a range of blade-jet speed ratios, total pressure ratios, and inlet total pressures at a constant inlet temperature of 800 R. Peak over-all efficiencies were obtained at blade-jet speed ratios from 0.525 to 0.575 for all runs. The variation in peak efficiency with inlet pressure and pressure ratio was of small magnitude for the conditions investigated.

TURBINES - AXIAL FLOW↗

Results of Flight Tests to Determine Drag of Parabolic and Cone-cylinder Bodies of Very Large Fineness Ratios at Supersonic Speeds

Results of a free-flight investigation at supersonic speeds to determine zero-lift drag of a series of bodies of revolution are presented. Configurations tested included two parabolic bodies with fineness ratios of 17.78 and 24.5 and two 8 degree cone-cylinder bodies with fineness ratios of 17.2 and 21.2. Results of previous tests of similar parabolic bodies but with lower fineness ratios are included in this paper for comparison. All bodies for which data are presented in this paper had a base-to-maximum-diameter ratio of 0.437. Calculated drag coefficients are shown for all bodies for which data are presented. (author)

Welsh, Clement J↗

Preliminary investigation of cooling-air ejector performance at pressure ratios from 1 to 10

Preliminary investigation was made of conical cooling air ejector at primary pressure ratios from 1 to 10. The cooling-air flow was maintained at zero and the resulting pressure variation in the shroud indicated pumping ability. The cooling-air flow was maintained at zero and the resulting pressure variation in the shroud indicated pumping ability. The gross thrust of the ejector and nozzle were compared. Several ratios of the spacing between the nozzle and shroud exit to the nozzle exit diameter were investigated for several shroud to nozzle exit diameter ratios. Maximum gross thrust loss occurred under conditions of zero cooling-air flow and was as much as 35 percent below nozzle jet thrust. For minimum thrust loss, ejector should be designed with as low diameter and spacing ratio as possible.

PUMPS, JET AND THRUST AUGMENTORS↗

Effect of Jet-nozzle-expansion Ratio on Drag of Parabolic Afterbodies

The interaction of the flow from one convergent and two convergent-divergent nozzles on parabolic afterbodies was studied at free-stream Mach numbers of 2.0, 1.6, and 0.6 over a range of jet pressure ratio. The influence of the jet on boattail and base drag was very pronounced. Study of the total external afterbody drag values at supersonic speeds indicated that, over most of the high-pressure-ratio range, increasing the nozzle design expansion ratio increased the drag even though the boattail area was reduced. Increasing the pressure ratio tended to increase slightly the total-drag increment caused by angle-of-attack operation.

Englert, Gerald W↗