SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
A technique suitable for measuring fluctuating temperatures in supersonic turbulent flows of N2 seeded with NO has been demonstrated in a nonflowing cell. The method relies on the two photon excitation of two selected ro-vibronic transitions in the NO gamma (alpha 2 sigma+, v prime = 0 yields ch1zp1, v double prime = 0). Previously announced in STAR as N83-20079
Improved second generation wind algorithms are used to process the three month SEASAT SMMR and SASS data sets. The new algorithms are derived without using in situ anemometer measurements. All known biases in the sensors prime measurements are removed, and the algorithms prime model functions are internally self-consistent. The computed SMMR and SASS winds are collocated and compared on a 150 km cell-by-cell basis, giving a total of 115444 wind comparisons. The comparisons are done using three different sets of SMMR channels. When the 6.6H SMMR channel is used for wind retrieval, the SMMR and SASS winds agree to within 1.3 m/s over the SASS primary swath. At nadir where the radar cross section is less sensitive to wind, the agreement degrades to 1.9 m/s. The agreement is very good for winds from 0 to 15 m/s. Above 15 m/s, the off-nadir SASS winds are consistently lower than the SMMR winds, while at nadir the high SASS winds are greater than SMMR's. When 10.7H is used for the SMMR wind channel, the SMMR/SASS wind comparisons are not quite as good. When the frequency of the wind channel is increased to 18 GHz, the SMMR/SASS agreement substantially degrades to about 5 m/s.
The effect of microstructure on fatigue crack propagation at 650 C has been studied in a P/M nickel-base superalloy, Astroloy. Crack propagation data were obtained in air and vacuum at 20 cpm with a modified compact tension specimen. The rate of crack growth, da/dn, was correlated with the stress intensity range. Key microstructural variables examined were grain size and the distribution and size of the strengthening gamma prime phase. A fine grain size less than 20 microns always promoted rapid, intergranular failure, while a large grain size promoted slower, transgranular failure which decreased as the size and volume fraction of aging gamma prime was manipulated so as to increase alloy strength. The rapid, intergranular mode of failure of the fine grain microstructures was suppressed in vacuum.
The broad fluorescence spectrum and Franck-Condon shift of the B-X system of S2 are exploited in broad-band-gain experiments using the absorption of 308-nm XeCl excimer radiation to pump the level (upsilon-prime = 4) in an S2 vapor with and without Ar. The fluorescence spectra are examined to determine the effects of gas collisions, and the intense near-UV and visible bands are attributed to the redistribution of the population among the upsilon-prime levels resulting from S2-Ar collisions. Broad-band gain is observed on the rare-gas relaxation bands (2,17) (about 475 nm) and (3,18) (480 nm), while absorption is found in the (0,6), (0,7), and (0,8) near-UV (about 360-380-nm) bands where a transient population cascading down the X-state manifold fills the lower levels. It is inferred from the achievement of gain over much of the S2 fluorescence bandwidth that nonselective pumping mechanisms like discharges, solar energy, or flashlamps can be used with S2 as the tunable, chemically stable 'dye'.
Pulsed laser photolysis of C2N2 at 193 nm has been used as a source of CN radicals in both the v-double-prime = 0 and v-double-prime = 1 levels. Individual rovibronic levels of these radicals were measured as a function of time with a tunable dye laser. From these measurements the rate constants for the reaction of each of these vibrational levels with H2, O2, CO, CO2, N2, HCN, C2N2, and CH4 have been determined. Some enhancement in the rate constant with vibrational energy which could not be ascribed to quenching was observed for O2, CH4, and H2. Only vibrational quenching was observed for HCN, N2, CO2, CO and C2N2. In the CO case the vibrational quenching rate appears to be significantly enhanced by complex formation during the quenching process.
The dipole moment of the A2Pi(u)-X2Pi(g) transition of O2(+) is calculated as a function of internuclear distance using ab initio methods. The band absorption oscillator strengths and band transition probabilities of the second negative system are derived and the resulting lifetimes are compared with experimental data. The high-lying v double prime levels of the ground state may decay into low-lying v prime levels of the excited state. The corresponding radiative lifetimes are calculated.
A structural study was carried out on Co modified Udimet 738 alloys containing 0.04, 0.10, and 0.20 wt % Zr at 0.01 and 0.03 wt % B levels. Samples in the as-cast and solution-treated conditions were exposed at 843 C to study structural stability. The structures produced by the interactions of Co, Zr, and B were studied by SEM, X-ray diffraction, and dispersive analysis techniques. The additions of large amounts of Zr and B were found to increase the solidification range of the U-738. Structural changes involved eutectic gamma prime islands, formation of low melting point compounds, and precipitation of borides and Zr rich phases. Boron and zirconium additions did not show substantial changes in mechanical properties. Removal of Co from the alloys resulted in reduction of the matrix solubility for carbon and increase in the gamma prime solvus. Structural instabilities found were continuous grain boundary M23C6 films, MC breakdown, and plate-like phases. Removal of cobalt resulted in a slight decrease in tensile and stress rupture properties. Detailed structural results presented.
Procedures followed in developing a test case geographic information system derived primarily from remotely sensed data for the North Cache Soil Conservation District (SCD) in northern Utah are outlined. The North Cache SCD faces serious problems regarding water allocation, flood and geologic hazards, urban encroachment into prime farmland, soil erosion, and wildlife habitat. Four fundamental data planes were initially entered into the geo-referenced data base: (1) land use/land cover information for the agricultural and built-up areas of the valley obtained from various forms of aerial photography; (2) vegetation/land cover in mountains classified digitally from LANDSAT; (3) geomorphic terrain units derived from aerial photography and soil maps; and (4) digital terrain maps obtained from DMA digital data. The land use/vegetation/land cover information from manual photographic and LANDSAT interpretation were joined digitally into a single data plane with an integrated legend, and segmented into quadrangle units. These were merged with the digitized geomorphic units and the digital terrain data using a Prime 400 minicomputer. All data planes were geo-referenced to a UTM coordinate grid.
A joint project to design, develop, procure, and produce Centaur upper stages for use with the Space Shuttle is discussed. A common Centaur G stage 6 meters (19.5 feet) in length is being jointly developed. A longer version designated Centaur G Prime is being developed by NASA to accomplish the Galileo and International Solar-Polar Mission flights in 1986. The Centaur G and G Prime will have the capability to place, respectively, approximately 4540 kilograms (10,000 pounds) and 5910 kilograms (13,000 pounds) into geosynchronous orbit from a standard Shuttle parking orbit of 278 kilometers (150 nautical miles) and Shuttle performance (lift) capability 29,500 kilograms (65,000 pounds). The advent of high energy upper stage capability in 1986 will permit space users and spacecraft developers to utilize spacecraft growth, stage combination concepts with storage modules, teleoperator systems, and other mission peculiar devices to satisfy complex mission demands. These capabilities should greatly enhance the usefulness of the space environment and stimulate mission planners toward conception of innovative means to meet ever increasing mission requirements.
The effects of chromium and aluminum on the mechanical and oxidation properties of a series of gamma-prime-strengthened alloys based on CG-27 were studied. Gamma-prime dispersion and solid-solution strengthening were the principal modes of alloy strengthening. The oxidation attack parameter K sub a decreased with increasing Cr and Al contents for each alloy group based on Al content. As a group, alloys with 3 wt % Al had the lowest attack parameters. Therefore, 3 wt % is the optimum level of Al for parabolic oxidation behavior. Spalling, due to diffusion-induced grain growth, was controlled by the overall Cr and Al levels. The alloy with 4 wt % Cr and 3 wt % Al had stress-rupture properties superior to those of the base alloy, CG-27, and maintained parabolic oxidation behavior while the Cr content was reduced by two-thirds of its value in cast CG-27.
Positron lifetime measurements were made in copolyimides synthesized from linear 4,4 prime-bis(3,4-dicarboxyphenoxy) diphenylsulfide dianhydride (BDSDA)/4,4 prime-diaminodiphenyl (ODA) and BDSDA/1,3-diaminobenzene (m-phenylene diamine) homopolymers. The probability of positronium formation as well as its subsequent lifetime are lower in the BDSDA/ODA/MPD (50-50) copolyimide, indicating the presence of a transition molecular architecture characterized by higher electron density and stronger bonds which permit both chemical as well as physical entry of water molecules into it. The presence of this transition region imparts unique physical and mechanical properties to the copolyimide.
When some nuclei are free from strong gravitational field, they are unstable and will become stable nuclei by competitions of following processes: (1) neutron-evaporation; (2) spontaneous fission; and (3) beta prime 3-decay. At the initial stage, (1) and (2) are important and (3) can be ignored. The qualitative results are as follows: (1) it seems that nuclei with A 100 come from the spontaneous fission and beta prime decay of neutron-evaporated nuclei with A similiar to 140-440, which can replace the r-process; (2) the super-heavy elements with Z=114--126 (A similiar to 330--360) can be formed. They can be observed in cosmic rage if they have the halftime T 10 to the 7th poweer years; (3) the peak in the rare-earth elements comes from the symmetric fission of super-heavy elements; (4) there are more neutron-rich nuclei in the fragments; and (5) the abundances of a 83 elements in cosmic rays are one order of magnitude higher than that in the solar system.
The objective of the study was to examine the effect of various microstructures on the fatigue and damage accumulation behavior of Waspaloy, a nickel-base alloy commonly used in aircraft engines. Shearing was the dominant deformation mode in specimens with coarse grains and small (50-80 A) gamma prime particles, whereas Orowan looping was dominant in fine-grained specimens with large (about 900 A) gamma prime particles. At temperatures up to 500 C, cracks initiated transgranularly, while at 800 C the failure process was intergranular for both coarse-grained and fine-grained specimens. At temperatures above 500 C, a significant decrease in the fatigue life was observed for both coarse-grained and fine-grained material.
The effect of cobalt on the workability of nickel-base superalloys is examined with reference to experimental results for four heats of alloys based on the Nimonic 115 composition with varying amounts of nickel substituted for the nominal 14 percent cobalt. It is shown that Co lowers the gamma-prime solvus, which in turn lowers the Cr23C6 carbide solvus. It is further shown that these solvus temperatures bracket the hot working range for the alloys. However, thermomechanical processing modifications reflecting the effect of Co on the gamma-prime and carbide solvi are shown to restore the workability and the properties of alloys with little or no cobalt.
The mechanism responsible for the radiation observed near the earth bow shock at twice the plasma frequency f(p) is investigated theoretically. A model comprising two three-wave steps and involving Langmuir (L), ion-sound (S), and EM (t) waves is proposed: L + or - S yields L-prime; L + L-prime yields t. This model is shown to be consistent with observations of low-frequency S-like waves (Anderson et al., 1981), and further observational tests are suggested. A critical examination of the theory of Fung et al. (1982) is included, and it is found that an important term in the absorption coefficient was neglected. Correcting this error leads to an intrinsic theoretical brightness-temperature limit of 3 x 10 to the 9th K, well below the observed brightness temperature of the 2 f(p) radiation, about 10 to the 11th K.
A ray tracing analysis has been performed for the spectral slicing zoom X-ray telescope for configurations in which a convex layered synthetic microstructure (LSM) optic is placed in front of the prime focus or a concave LSM optic is placed behind the prime focus. The analysis has considered the geometrical shape of the LSM optic to be either a hyperboloid, sphere, ellipsoid or constant optical path aspheric element for two configurations of the glancing incidence X-ray telescope: the ATM Experimental S-056 Wolter I system and the Stanford/MSFC Wolter-Schwarzchild nested system. For the different systems the RMS blur circle radii, the point spread function (PSF), the full width half maximum (FWHM) of the PSF have been evaluated as a function of field angle and magnification of the secondary to determine resolution of the system. The effects of decentration and tilt of the selected LSM element on the performance of the system have been studied to determine mounting and alignment tolerances.
A propulsion module to augment the Centaur G-Prime and the Aerobraked OTV (AOTV) injection energy (C sub 3) was studied. The characteristics and performance of a variety of Earth-storable and cryogenic propulsion systems are presented. A pump-fed, cryogenic O2/H2 propulsion system enables the elimination of a three-year delta V Earth gravity assist (delta VEGA) maneuver for several planetary missions currently under consideration by the NASA. This trip time reduction can significantly reduce mission support costs, reduce spacecraft (S/C) life requirements and potentially increase the probability of mission success. This study also shows that an O2/H2 propulsion module, developed for Centaur C sub 3 augmentation can be used with a space-based AOTV in the return mode, allowing the reuse of the high-value AOTV while still delivering the required high-injection energy for direct planetary missions. The propulsion module performance was estimated for a space shuttle delivery capability to LEO of 65,000 lb sub m and 75,000 lb sub m. The required minimum thrust level to minimize gravity losses was also determined. For several currently planned NASA planetary missions, the Centaur G-Prime injection energy is augmented by a delta VEGA maneuver. For these missions, direct injection by the Centaur cannot provide a shorter trip time than the delta VEGA injection trip time.
The cyclic flow response and crack growth behavior of Waspaloy at room temperature and 650 C under tensile loading and torsional loading was studied, for two conditions of Waspaloy: fine grain, large gamma prime size; coarse grain, small gamma prime size. The fine grain material showed 5 to 10 percent hardening after about 10 percent of life, with sequent softening to failure at both themperature levels. The coarse grain material showed either stable response or monotonic softening to failure. Early crack initiation was observed on planes of maximum shear, with eventual branching to principle planes under torsional loading; cracks were always normal to load axis under tensile loading. Also, crack paths were intergranular at 650 C, mostly transgranular at room temperature.