Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Laser Applications”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Applications of tunable high energy/pressure pulsed lasers to atmospheric transmission and remote sensing

Atmospheric transmission of high energy C12 O2(16) lasers were improved by pulsed high pressure operation which, due to pressure broadening of laser lines, permits tuning the laser 'off' atmospheric C12 O2(16) absorption lines. Pronounced improvement is shown for horizontal transmission at altitudes above several kilometers, and for vertical transmission through the entire atmosphere. The atmospheric transmission of tuned C12 O2(16) lasers compares favorably with C12 O2(18) isotope lasers and CO lasers. The advantages of tunable, high energy, high pressure pulsed lasers over tunable diode lasers and waveguide lasers, in combining high energies with a large tuning range, are evaluated for certain applications to remote sensing of atmospheric constituents and pollutants. Pulsed operation considerably increases the signal to noise ratio without seriously affecting the high spectral resolution of signal detection obtained with laser heterodyning.

Hess, R. V.↗
DOE OSTI2020

Laser glazing of cold sprayed coatings for the mitigation of stress corrosion cracking in light water reactor (LWR) applications

The effect of laser power, traverse speed, and cold spray coating thickness were examined with the goal of mitigating and repairing stress corrosion cracking (SCC) in light water reactor (LWR) environment. For this purpose, SCC-susceptible Alloy 600 substrate material was coated with SCC-resistant Alloy 690 via the cold spray technique. The cold spray coated substrate was then laser-glazed using various laser parameters. Single pass and multiple pass laser glazed regions were created to determine the effects. For this purpose, the area of the fusion zone, depth of the fusion zone, and elemental composition of the cross section were examined by optical microscopy, scanning electron microscopy, and energy dispersive spectroscopy. Additionally, it was shown that chromium dilution from the laser glazed region into the substrate is not a significant factor in laser glazed cold spray coated samples. Separate laser glazed samples were subjected to ASTM 633C to determine coating adhesion. Finally, by using interrupted SCC crack growth rate tests, it was shown that low traverse speeds and high laser powers produce deep fusion zones within the cold sprayed coating and substrate that can be used to seal pre-existing cracks, thus stopping SCC growth.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Advancing extreme pulsed lasers through measurements: summary of the pulsed laser metrology workshop

In this report we present consensus findings produced during the pulsed laser metrology (PLM) workshop (Boulder, CO, USA, August 2025). The workshop was a meeting of 35 scientists from private industry, academia, and U.S. government to compile a list of the metrology needs to support extreme pulsed laser development and implementation. We define ‘extreme pulsed lasers’ loosely as those with peak powers above 1 TW or multi-Joule pulse energies. Such lasers are being increasingly used and investigated for use in high energy particle acceleration, short wavelength radiation generation, laser-based fusion, etc. The rapid growth of these fields and the proliferation of extreme lasers for these applications, coupled with the extreme electric fields they generate and relative scarcity of such lasers, presents unique challenges to accuracy in their measurement. The PLM workshop was a two-day event designed to hear from users, developers, and researchers on the current state of optical metrology associated with these extreme pulsed lasers. The goal was to identify the most important measurement challenges limiting development and implementation of these lasers in practical applications. We report here the conclusions and recommendations of this workshop. The hope is that this document will become the first of many iterations which track the status of measurement needs supporting extreme pulsed lasers.

Lasers↗
NASA NTRS1985

Pulsed excimer laser processing for cost-effective solar cells

The application of excimer laser in the fabrication of photovoltaic devices was investigated extensively. Processes included junction formation, laser assisted chemical vapor deposition metallization, and laser assisted chemical vapor deposition surface passivation. Results demonstrated that implementation of junction formation by laser annealing in production is feasible because of excellent control in junction depth and quality. Both metallization and surface passivation, however, were found impractical to be considered for manufacturing at this stage.

Wong, David C.↗
DOE OSTI2013

Application of maximum likelihood methods to laser Thomson scattering measurements of low density plasmas

Laser Thomson scattering (LTS) is an established plasma diagnostic technique that has seen recent application to low density plasmas. It is difficult to perform LTS measurements when the scattered signal is weak as a result of low electron number density, poor optical access to the plasma, or both. Photon counting methods are often implemented in order to perform measurements in these low signal conditions. However, photon counting measurements performed with photo-multiplier tubes are time consuming and multi-photon arrivals are incorrectly recorded. In order to overcome these shortcomings a new data analysis method based on maximum likelihood estimation was developed. The key feature of this new data processing method is the inclusion of non-arrival events in determining the scattered Thomson signal. Maximum likelihood estimation and its application to Thomson scattering at low signal levels is presented and application of the new processing method to LTS measurements performed in the plume of a 2-kW Hall-effect thruster is discussed.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Cost Effectiveness of Laser Powder Bed Fusion for Heavy Duty Applications

ORNL (Contractor) and Cummins Inc. (Participant) collaborated to determine the cost effectiveness of laser powder bed fusion (LPBF) for heavy duty applications. The team demonstrated that coupons can be fabricated with two distinct process parameters i.e., different process parameters for the bulk and surface of the material. This is important for enabling the manufacturing of components in a production environment where the bulk of the material can be processed rapidly while high quality surface finish can minimize post-process machining as well as enable superior fatigue performance if the material were to be used in as-deposited condition.

36 MATERIALS SCIENCE↗
DOE OSTI2013

Laser polishing of niobium for SRF applications

Smooth interior surfaces are desired for niobium SRF cavities, now obtained by buffered chemical polish (BCP) and/or electropolish (EP). Laser polishing is a potential alternative, having advantages of speed, freedom from chemistry and in-process inspection. Here we show that laser polishing can produce smooth topography with Power Spectral Density (PSD) measurements similar to that obtained by EP. We studied the influence of the laser power density and laser beam raster rate on the surface topography. These two factors need to be combined carefully to smooth the surface without damaging it. Computational modeling was used to simulate the surface temperature and explain the mechanism of laser polishing.

Zhao, Liang↗
DOE OSTI2025

Generation of radioisotopes for medical applications using high-repetition, high-intensity lasers

We used the PW high-repetition laser facility VEGA-3 at Centro de Láseres Pulsados in Salamanca, with the goal of studying the generation of radioisotopes using laser-driven proton beams. Various types of targets have been irradiated, including in particular several targets containing boron to generate α-particles through the hydrogen–boron fusion reaction. We have successfully identified γ-ray lines from several radioisotopes created by irradiation using laser-generated α-particles or protons including 43 Sc, 44 Sc, 48 Sc, 7 Be, 11 C and 18 F. We show that radioisotope generation can be used as a diagnostic tool to evaluate α-particle generation in laser-driven proton–boron fusion experiments. We also show the production of 11 C radioisotopes, ≈ 6 × 10 6 , and of 44 Sc radioisotopes, ≈ 5 × 10 4 per laser shot. This result can open the way to develop laser-driven radiation sources of radioisotopes for medical applications.

gamma ray spectroscopy↗
NASA NTRS2015

A plasma-based non-intrusive point source for acoustic beamforming applications

A laser-generated plasma acoustic point source is used to directly measure the point spread function (PSF) of a microphone phased array. In beamforming analysis of microphone phased array data, the true acoustic field is convolved with the array's PSF. By directly measuring the PSF, corrections to the array analysis can be computed and applied. The acoustic source is measured in an open-jet aeroacoustic facility to evaluate the effects of sampling rate, microphone installation, source shift, reflections, shear layer refraction and model presence. Results show that measurements exhibit behavior consistent with theory with regard to source shift and shear layer refraction. Application of a measured PSF in beamforming analysis shows the process provides an effective in-situ method for array calibration both with and without flow and allows for corrections to incorporate reflections and scattering. The technique improves the agreement of beamforming results with the true spectrum of a known source, especially in the presence of reflections.

phased array↗
DOE OSTI2014

Note: Deep ultraviolet Raman spectrograph with the laser excitation line down to 177.3 nm and its application

Deep UV Raman spectrograph with the laser excitation line down to 177.3 nm was developed in this laboratory. An ellipsoidal mirror and a dispersed-subtractive triple monochromator were used to collect and disperse Raman light, respectively. The triple monochromator was arranged in a triangular configuration with only six mirrors used. 177.3 nm laser excited Raman spectrum with cut-off wavenumber down to 200 cm{sup −1} and spectral resolution of 8.0 cm{sup −1} can be obtained under the condition of high purity N{sub 2} purging. With the C–C σ bond in Teflon selectively excited by the 177.3 nm laser, resonance Raman spectrum of Teflon with good quality was recorded on the home-built instrument and the σ-σ{sup *} transition of C–C bond was studied. The result demonstrates that deep UV Raman spectrograph is powerful for studying the systems with electronic transition located in the deep UV region.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
NASA NTRS1977

Laser anemometer signals - Visibility characteristics and application to particle sizing

Investigations have been conducted concerning the characteristics of the visibility function as determined by the parameters of the laser anemometer system and the electromagnetic scattering properties of the particles. Experiments have been performed to evaluate the backscatter visibility of signals from a symmetric, s polarization laser anemometer as a function of the particle diameter and a parameter ratio. The results have been compared with the predictions of an analysis based on Mie's scattering theory. The analysis has also been used to evaluate the effects of the collecting aperture's size and location.

Adrian, R. J.↗
NASA NTRS1971

A relative performance analysis of atmospheric Laser Doppler Velocimeter methods.

Evaluation of the effectiveness of atmospheric applications of a Laser Doppler Velocimeter (LDV) at a wavelength of about 0.5 micrometer in conjunction with dual scatter LDV illuminating techniques, or at a wavelength of 10.6 micrometer with local oscillator LDV illuminating techniques. Equations and examples are given to provide a quantitative basis for LDV system selection and performance criteria in atmospheric research. The comparative study shows that specific ranges and conditions exist where performance of one of the methods is superior to that of the other. It is also pointed out that great care must be exercised in choosing system parameters that optimize a particular LDV designed for atmospheric applications.

Farmer, W. M.↗
NASA NTRS1988

Laser production and heating of plasma for MHD application

Experiments have been made on the production and heating of plasmas by the absorption of laser radiation. These experiments were performed to ascertain the feasibility of using laser-produced or laser-heated plasmas as the input for a magnetohydrodynamic (MHD) generator. Such a system would have a broad application as a laser-to-electricity energy converter for space power transmission. Experiments with a 100-J-pulsed CO2 laser were conducted to investigate the breakdown of argon gas by a high-intensity laser beam, the parameters (electron density and temperature) of the plasma produced, and the formation and propagation of laser-supported detonation (LSD) waves. Experiments were also carried out using a 1-J-pulsed CO2 laser to heat the plasma produced in a shock tube. The shock-tube hydrogen plasma reached electron densities of approximately 10 to the 17th/cu cm and electron temperatures of approximately 1 eV. Absorption of the CO2 laser beam by the plasma was measured, and up to approximately 100 percent absorption was observed. Measurements with a small MHD generator showed that the energy extraction efficiency could be very large with values up to 56 percent being measured.

Jalufka, N. W.↗
DOE OSTI2019

A Survey of Transparent Conducting Films and Optoelectrical Materials for High Optical Power Applications

The lifetime laser damage performance of a wide range of transparent conductive materials is assessed, including ultrathin metal films, doped metal oxides, doped compound semiconductors, and graphene whose carrier densities span five orders of magnitude from 10 18 to 10 23 cm -3 . Lifetime laser damage thresholds are determined by exposing material surfaces to repeated nanosecond laser pulses at near IR wavelengths (1064 nm). Near threshold fluences, two distinct damage modes, i.e., bulk and discrete, emerge depending on carrier density. These bulk and discrete damage modes are attributed to free carrier-induced bulk and localized, defect-driven absorption processes, respectively. For polycrystalline films with free carrier densities greater than ≈10 20 cm -3 , laser damage thresholds are less than 5 J cm -2 . In contrast, bulk absorption is not apparent at thresholds substantially higher than ≈10 J cm-2 in single-crystal films with free carrier concentrations lower than ≈10 19 cm -3 . By increasing thickness, films with lower carrier densities can deliver relevant levels of sheet conductance (<200 Ω sq -1 ) while remaining transparent. These lifetime laser damage threshold measurements offer systematic criteria to select materials aimed at handling high optical powers in optoelectronics devices and emerging plasmonic and metamaterials for lasers.

36 MATERIALS SCIENCE↗
DOE OSTI2012

Kr II laser-induced fluorescence for measuring plasma acceleration

We present the application of laser-induced fluorescence of singly ionized krypton as a diagnostic technique for quantifying the electrostatic acceleration within the discharge of a laboratory cross-field plasma accelerator also known as a Hall effect thruster, which has heritage as spacecraft propulsion. The 728.98 nm Kr II transition from the metastable 5d{sup 4}D{sub 7/2} to the 5p{sup 4}P{sub 5/2}{sup Ring-Operator} state was used for the measurement of laser-induced fluorescence within the plasma discharge. From these measurements, it is possible to measure velocity as krypton ions are accelerated from near rest to approximately 21 km/s (190 eV). Ion temperature and the ion velocity distributions may also be extracted from the fluorescence data since available hyperfine splitting data allow for the Kr II 5d{sup 4}D{sub 7/2}-5p{sup 4}P{sub 5/2}{sup Ring-Operator} transition lineshape to be modeled. From the analysis, the fluorescence lineshape appears to be a reasonable estimate for the relatively broad ion velocity distributions. However, due to an apparent overlap of the ion creation and acceleration regions within the discharge, the distributed velocity distributions increase ion temperature determination uncertainty significantly. Using the most probable ion velocity as a representative, or characteristic, measure of the ion acceleration, overall propellant energy deposition, and effective electric fields may be calculated. With this diagnostic technique, it is possible to nonintrusively characterize the ion acceleration both within the discharge and in the plume.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2016

Measurement and Analysis of Porosity in Al-10Si-1Mg Components Additively Manufactured by Selective Laser Melting

Aluminum alloys are candidate materials for weight critical applications because of their excellent strength and stiffness to weight ratio. However, defects such as voids decrease the strength and fatigue life of these alloys, which can limit the application of Selective Laser Melting. In this study, the average volume fraction, average size, and size distribution of pores in Al10-Si-1Mg samples built using Selective Laser Melting have been characterized. Synchrotron high energy X-rays were used to perform computed tomography on volumes of order one cubic millimeter with a resolution of approximately 1.5 μm. Substantial variations in the pore size distributions were found as a function of process conditions. Even under conditions that ensured that all locations were melted at least once, a significant number density was found of pores above 5 μm in diameter.

36 MATERIALS SCIENCE↗