SEARCH · Engineering Papers

Results for “Inlet”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

All sources NASA NTRS DOE OSTI

NASA NTRS1981

Ultra-lean combustion at high inlet temperatures

Combustion at inlet-air temperatures of 1100 to 1250 K was studied for application to advanced automotive gas turbine engines. Combustion was initiated by the hot environment, and therefore no external ignition source was used. Combustion was stabilized without a flameholder. The tests were performed in a 12-cm-diameter test section at a pressure of 250,000 Pa, with reference velocities of 32 to 60 m/s and at maximum combustion temperatures of 1350 to 1850 K. Number 2 diesel fuel was injected by means of a multiple-source fuel injector. Unburned hydrocarbon emissions were negligible for all test conditions. Nitrogen oxide emissions were less than 1.9 g NO2/kg fuel for combustion temperatures below 1680 K. Carbon monoxide emissions were less than 16 g CO/kg fuel for combustion temperatures greater than 1600 K, inlet-air temperatures higher than 1150 K, and residence times greater than 4.3 ms.

Anderson, D. N.↗

NASA NTRS1981

Effect of a part span variable inlet guide vane on TF34 fan performance

Experimental aerodynamic and performance data were obtained from a TF34 engine. Part span variable inlet guide vanes mounted in front of the fan on the TF34 engine were tested to demonstrate the feasibility of modulating air flow and thrust for vertical takeoff aircraft systems. The fan was mapped to stall for a range of speeds and variable inlet guide were settings. Modulated fan tip performance and unmodulated hub performance were evaluated with a without an extended fan bypass splitter. The effect of a crosswind distortion screen on performance was also evaluated.

Alvarez, J.↗

NASA NTRS1982

Experimental and analytical results of tangential blowing applied to a subsonic V/STOL inlet

Engine inlets for subsonic V/STOL aircraft must operate over a wide range of conditions without internal flow separation. Experimental and analytical investigations were conducted to evaluate the effectiveness of tangential blowing to maintain attached flow to high angles of attack. The inlet had a relatively thin lip with a blowing slot located either on the lip or in the diffuser. The height and width of these slots was varied. Experimentally determined flow separation boundaries showed that lip blowing achieved higher angle of attack capability than diffuser blowing. This capability was achieved with the largest slot circumferential extent and either of the two slot heights. Predicted (analytical) separation boundaries showed good agreement except at the highest angles of attack.

Burley, R. R.↗

NASA NTRS1981

Some aspects of calculating flows about three-dimensional subsonic inlets

Various three dimensional inlet models were calculated based on the potential flow model. Results are presented in the forms of surface static pressure, flow angularity, surface flow pattern, and inlet flow field. It is indicated that the extension of the lower lip can reduce the adverse pressure gradient and increase the flow separation bound.

Kao, H. C.↗

NASA NTRS1982

Three-dimensional flow calculations including boundary layer effects for supersonic inlets at angle of attack

An analysis is presented for calculating the steady three-dimensional flow field in supersonic mixed-compression inlets at incidence. A zonal modeling approach is employed to obtain the solution. The supersonic core flow is computed using a second-order pentahedral bicharacteristic algorithm. The bow shock wave and the reflected internal shock train are determined using a three-dimensional discrete shock fitting procedure. The boundary layer flow adjacent to both the centerbody and the cowl is computed using a second-order implicit finite difference method. The flow in a shock wave-boundary layer interaction region is computed using an integral formulation. The culmination of the present research effort is the development of a production-type computer program capable of analyzing flow in a variety of mixed-compression aircraft inlets. Numerical results and experimental correlations are presented to illustrate application of the analysis.

Vadyak, J.↗

NASA NTRS1982

Tangential blowing for control of strong normal shock - Boundary layer interactions on inlet ramps

The use of tangential blowing from a row of holes in an aft facing step is found to provide good control of the ramp boundary layer, normal shock interaction on a fixed geometry inlet over a wide range of inlet mass flow ratios. Ramp Mach numbers of 1.36 and 1.96 are investigated. The blowing geometry is found to have a significant effect on system performance at the highest Mach number. The use of high-temperature air in the blowing system, however, has only a slight effect on performance. The required blowing rates are significantly high for the most severe test conditions. In addition, the required blowing coefficient is found to be proportional to the normal shock pressure rise.

Schwendemann, M. F.↗

NASA NTRS1982

Utilizing numerical techniques in turbofan inlet acoustic suppressor design

Numerical theories in conjunction with previously published analytical results are used to augment current analytical theories in the acoustic design of a turbofan inlet nacelle. In particular, a finite element-integral theory is used to study the effect of the inlet lip radius on the far field radiation pattern and to determine the optimum impedance in an actual engine environment. For some single mode JT15D data, the numerical theory and experiment are found to be in a good agreement.

Baumeister, K. J.↗

NASA NTRS1981

Experimental investigation of tangential blowing for control of the strong shock boundary layer interaction on inlet ramps

A 0.165-scale isolated inlet model was tested in the NASA Lewis Research Center 8-ft by 6-ft Supersonic Wind Tunnel. Ramp boundary layer control was provided by tangential blowing from a row of holes in an aft-facing step set into the ramp surface. Testing was performed at Mach numbers from 1.36 to 1.96 using both cold and heated air in the blowing system. Stable inlet flow was achieved at all Mach numbers. Blowing hole geometry was found to be significant at 1.96M. Blowing air temperature was found to have only a small effect on system performance. High blowing levels were required at the most severe test conditions.

Schwendemann, M. F.↗

NASA NTRS1983

Validation of a three-dimensional viscous analysis of axisymmetric supersonic inlet flow fields

A three-dimensional viscous marching analysis for supersonic inlets was developed. To verify this analysis several benchmark axisymmetric test configurations were studied and are compared to experimental data. Detailed two-dimensional results for shock-boundary layer interactions are presented for flows with and without boundary layer bleed. Three dimensional calculations of a cone at angle of attack and a full inlet at attack are also discussed and evaluated. Results of the calculations demonstrate the code's ability to predict complex flow fields and establish guidelines for future calculations using similar codes.

Benson, T. J.↗

NASA NTRS1983

Numerical analysis of a scramjet inlet flow field using the three-dimensional Navier-Stokes equations

A computer program has been developed to analyze supersonic combustion ramjet (scramjet) inlet flow fields. The program solves the three-dimensional Euler or Navier-Stokes equations in full conservation form by a well-known explicit, predictor-corrector technique. Turbulence is modeled by an algebraic eddy-viscosity model. Detailed laminar and turbulent flow results are presented for a symmetric wedge corner and a comparison is made with the available experimental results to allow assessment of the program. Results are then presented for an actual scramjet inlet configuration.

Kumar, A.↗

NASA NTRS1983

Flow fields and aerodynamic characteristics for hypersonic missiles with mid-fuselage inlets

A study was made to quantify forebody flow fields and to evaluate aerodynamic performance trends on a matrix of fuselage shapes for the mid-inlet/bolt-on-engine class of hypersonic airbreathing missiles for the Navy's vertical box launcher. The study indicated that inlet mass flow and pressure recovery can be increased by cambering the nose and increasing the width of the fuselage at both Mach 4 acceleration and Mach 6 cruise conditions. Aerodynamic trim predictions show that the drag at zero lift at Mach 4 decreases while the L/D max at Mach 6 increases with the nose camber, although these tendencies reverse with increasing width of maximum fuselage cross section.

Hunt, J. L.↗

NASA NTRS1983

The design and flight test of an engine inlet bulk acoustic liner

This paper summarizes the design, fabrication and flight evaluation of a Kevlar acoustic liner configuration for a JT15D turbofan engine. The liner was designed to suppress, by a measurable amount, a dominant (13,0) BPF tone. This tone or spinning mode was produced for research purposes by installing 41 circumferentially distributed small diameter rods upstream of the 28 fan blades. Duct liner attenuations calculated by a finite element procedure were compared to far field power (insertion) losses deduced from flight data. The finite element program modeled the variable geometry of the JT15D inlet and used a uniform flow with a boundary layer roll-off to model the inlet flow field. Calculated liner losses were generally conservative. That is, measured far field power losses were generally greater than attenuations calculated by the finite element computer program.

Lester, H. C.↗

NASA NTRS1983

Calculation of a simulated 3-D high speed inlet using the Navier-Stokes equations

A hybrid numerical algorithm, developed to solve the full three-dimensional Navier-Stokes equations, is applied to the computation of the flowfield in a simulated three-dimensional high speed aircraft inlet at a Mach number of 2.5 and Reynolds number of 1.4 x 10 to the 7th based on inlet length. The numerical algorithm incorporates a coordinate transformation in order to handle general flow geometries, and utilizes the algebraic turbulent eddy viscosity model of Baldwin and Lomax. The hybrid algorithm has been vectorized on the CDC CYBER 203 computer using the SL/1 vector programming language developed at NASA Langley. The computed results are compared with experimental measurements of the ramp and cowl static pressures, and boundary layer pitot profiles. The results are also compared with a previous two-dimensional Navier-Stokes computation of the same configuration. The agreement with the experimental data is generally good; however, additional improvements in turbulence modeling are needed.

Knight, D. D.↗

NASA NTRS1982

Experimental evaluation of inlet turbulence, wall boundary layer, surface finish, and fillet radius on small axial turbine state performance

The results of an experimental investigation are presented which establish the effects of surface finish, fillet radius, inlet boundary layer thickness, and free-stream inlet turbulence level on the aerodynamic performance of a small axial flow turbine stator. The principal objective was to help understand why large turbine efficiency is not maintained when a large turbine is scaled to a smaller size and to provide the turbine designer with the performance compromises expected for a small scale design. A comprehensive test matrix was used to gain an understanding of the effects of each variable over the full range of all the other variables.

Kozak, A. A.↗

NASA NTRS1983

Determining compressor-inlet airflow in the compact multimission aircraft propulsion simulators in wind-tunnel applications

Test techniques are being developed to use the Compact Multimission Aircraft Propulsion Simulator (CMAPS) in wind-tunnel tests. The CMAPS allows simultaneous simulation of inlet and exhaust flow fields. Static tests have been conducted to acquire CMAPS performance data and to evaluate four methods of determining compressor inlet airflow during wind-tunnel tests. The first method measures airflow at the compressor face; the second measures airflow in the compressor discharge duct; the third deduces the compressor airflow from the calibrated nozzle, turbine supply, and turbine bleed airflows; and the fourth correlates compressor airflow with the mixer pressure. Test results and the advantages, disadvantages, and expected accuracy of each method are discussed.

Smith, S. C.↗

NASA NTRS1984

Analytical Study of Blowing Boundary-Layer Control for Subsonic V/STOL Inlets

The analytical methods used to study blowing boundary-layer control (BLC) for subsonic V/STOL inlets are described. The methods are then shown to give good agreement with experimental results, both with and without blowing BLC. Finally, because of this good agreement, the methods were used to determine analytically the optimum (minimum blowing power required) location and height for a blowing slot within a subsonic V/STOL inlet.

Hwang, D. P.↗

NASA NTRS1984

Aerodynamic effect of combustor inlet-air pressure on fuel jet atomization

Mean drop diameters were measured with a recently developed scanning radiometer in a study of the atomization of liquid jets injected cross stream in high velocity and high pressure airflows. At constant inlet air pressure, reciprocal mean drop diameter, was correlated with airflow mass velocity. Over a combustor inlet-air pressure range of 1 to 21 atmospheres, the ratio of orifice to mean drop diameter, D(O)/D(M), was correlated with the product of Weber and Reynolds number, WeRe, and with the molecular scale momentum transfer ratio of gravitational to inertial forces.

Ingebo, R. D.↗

NASA NTRS1983

Inlet flow distortion in turbomachinery - Comparison of theory and experiment in a transonic fan stage

Consideration is given to both velocity and temperature circumferential inlet distortions at upstream infinity (Seidel et al., 1980). The blade rows here are modeled as semiactuator disks, and losses and quasi-steady deviation angle correlations are included in the analysis. The governing equations are linearized, and the perturbations in stagnation pressure and stagnation temperature at upstream infinity are represented as Fourier series. The flow in the rotor is modeled as inviscid, one-dimensional, unsteady, and compressible. the flow is steady elsewhere. The deviation angles for the rotor and stator are taken to be functions of the relative inlet angle and Mach number, and use is made of the correlations contained in Johnson and Bullock (1965). It is assumed that the losses in relative stagnation pressure in the rotor and stator occur across the trailing edge. Boundary conditions applied at the various stations furnish the equations that make it possible to solve for the several quantities introduced in the linearization of the governing equations.

Seidel, B. S.↗