Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Grid Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Integrated residential photovoltaic array development

Sixteen conceptual designs of residential photovoltaic arrays are described. Each design concept was evaluated by an industry advisory panel using a comprehensive set of technical, economic and institutional criteria. Key electrical and mechanical concerns that effect further array subsystem development are also discussed. Three integrated array design concepts were selected by the advisory panel for further optimization and development. From these concepts a single one will be selected for detailed analysis and prototype fabrication. The three concepts selected are: (1) An array of frameless panels/modules sealed in a T shaped zipper locking neoprene gasket grid pressure fitted into an extruded aluminum channel grid fastened across the rafters. (2) An array of frameless modules pressure fitted in a series of zipper locking EPDM rubber extrusions adhesively bonded to the roof. Series string voltage is developed using a set of integral tongue connectors and positioning blocks. (3) An array of frameless modules sealed by a silicone adhesive in a prefabricated grid of rigid tape and sheet metal attached to the roof.

Royal, G. C., III↗
NASA NTRS1985

Numerical simulation of flow through scramjet inlets using a three-dimensional Navier-Stokes code

A three-dimensional Reynolds-averaged Navier-Stokes code has been used to numerically analyze flow through a two-strut, supersonic combustion ramjet (scramjet) inlet configuration. It solves the governing equations in full conservation form using either the fully explicit or explicit-implicit method due to MacCormack. An algebraic two-layer eddy viscosity model is used for turbulent flow calculations. The analysis allows inclusion of end effects which are caused by the aft placement of the cowl on the underside of the inlet. A special grid has been developed to accommodate the struts embedded in the inlet flow field. Detailed numerical results are presented here for the two-strut configuration, and a comparison is made with the available experimental results.

Kumar, A.↗
NASA NTRS1989

Numerical simulation of flow through a two-strut scramjet inlet

A three-dimensional, Reynolds-averaged Navier-Stokes code has been used to numerically analyze flow through a two-strut, supersonic combustion ramjet (scramjet) inlet configuration. It solves the governing equations in full conservation form using either a fully explicit or explicit-implicit method. An algebraic, two-layer eddy-viscosity model is used for turbulent flow calculations. The analysis allows inclusion of end effects that are caused by the aft placement of the cowl on the underside of the inlet. A special grid has been developed to accommodate the struts embedded in the inlet flowfield. Detailed numerical results are presented here for the two-strut configuration, and a comparison is made with the available experimental results.

Kumar, Ajay↗
NASA NTRS1992

Application of space-marching methods to hypersonic forebody flow fields

The heavy reliance on CFD in the design of hypersonic flight vehicles emphasizes the importance of choosing computationally efficient techniques. As a result, the development and application of space-marching flow solvers for the parabolized Navier-Stokes equations have received considerable attention in the past decade. This paper summarizes a space-marching approach used at NASA Ames Research Center for the analysis of hypersonic vehicle forebodies. Aspects of the simulation process are addressed that contain features unique to space-marching flow solvers, such as grid generation, initial condition specification, and finite-rate chemistry models. For completeness, sections are also included on turbulence modeling and equilibrium air chemistry modeling. The discussion includes an overview of the computational methods utilized as well as a number of relevant results.

Lawrence, Scott L.↗
NASA NTRS1994

Measuring glass abundances in lunar agglutinates

The purpose of this study is to develop a standard method for measuring modal abundances of glass in single agglutinates in the lunar regolith. Not only does agglutinitic glass increase in single agglutinates as clasts of older agglutinates get incorporated into newer agglutinates with increasing maturity, but it is in this glassy phase that nanophase superparamagnetic Fe metal originates as a result of reduction reactions during the agglutination process. We report the results of two sets of independent measurements using two different methods to determine the proportion of glass in single agglutinates. We have used polished grain mounts (PGM) of five hand-picked single agglutinates from Apollo 16 soil 61181. The ISI Scanning Electron Microscope (SEM) fitted with a high-resolution Backscattered Electron (BSE) detector was used to collect high-contrast BSE images of the agglutinates. Several images were collected to represent each single agglutinate. The contrast, brightness, and focus were adjusted to optimize each image collected. Histograms of the grayscale range for all images produced four 'peaks' corresponding to epoxy, glass, crystalline phases, and metal grains. We analyzed every grid point for 12 elements with a less than 1 micron electron beam using a CAMECA SX-50 electron probe microanalyzer (EPM). If any analysis was not within about 10% of the stoichiometry of a known lunar mineral, we considered that point to be nonmineralic. Our results show that there is a remarkable correspondence in the glass percentages obtained by the two methods. The EPM method may overestimate glass because secondary fluorescence from dusty clasts in agglutinitic glass can give the appearance of nonmineralic targets. The BSE method may underestimate glass because the diversity of compositions of agglutinitic glass may not be contained under one grayscale 'peak' during image analysis.

Strait, M. M.↗
NASA NTRS2000

Automated, Parametric Geometry Modeling and Grid Generation for Turbomachinery Applications

The objective of this Phase I project is to develop a highly automated software system for rapid geometry modeling and grid generation for turbomachinery applications. The proposed system features a graphical user interface for interactive control, a direct interface to commercial CAD/PDM systems, support for IGES geometry output, and a scripting capability for obtaining a high level of automation and end-user customization of the tool. The developed system is fully parametric and highly automated, and, therefore, significantly reduces the turnaround time for 3D geometry modeling, grid generation and model setup. This facilitates design environments in which a large number of cases need to be generated, such as for parametric analysis and design optimization of turbomachinery equipment. In Phase I we have successfully demonstrated the feasibility of the approach. The system has been tested on a wide variety of turbomachinery geometries, including several impellers and a multi stage rotor-stator combination. In Phase II, we plan to integrate the developed system with turbomachinery design software and with commercial CAD/PDM software.

Harrand, Vincent J.↗
NASA NTRS2001

ISO Guest Observer Data Analysis and LWS Instrument Team Activities

The following is an interim annual report. Dr. Smith is currently on an extended TDY to the Istituto di Fisica dello Spazio Interplanetario (IFSI) at the Consilio Nazionale delle Richerche (CNR) in Rome, Italy, where he has been working on a related NASA grant in support of analysis of Infrared Space Observatory (ISO) data on star formation in Ultra Luminous Infrared Galaxies and our galaxy. Work emphasizes development of metal mesh grids for use in spacecraft, and the design and fabrication of test elements by the Naval Research Laboratory, Washington D.C. Work has progressed well, but slowly, on that program due to the departure of a key engineer. NASA has been advised of the delay, and granted a no-cost extension, whereby SAO has authorized a delay in the final report from NRL. Nevertheless NRL has continued to make progress. Two papers have been submitted to refereed journals related to this program, and a new design for mesh operating in the 20-40 micron region has been developed. Meetings continue through the summer on these items. A new technical scientist has been made a job offer and hopefully will be on board NRL shortly, although most of the present grant work is already completed. A more complete report, with copies of the submitted papers, designs, and other measures of progress, will be submitted to NASA in September when Dr. Smith returns from his current TDY.

Smith, Howard↗
NASA NTRS2013

Recent Development in the CESE Method for the Solution of the Navier-Stokes Equations Using Unstructured Triangular or Tetrahedral Meshes With High Aspect Ratio

In the multidimensional CESE development, triangles and tetrahedra turn out to be the most natural building blocks for 2D and 3D spatial meshes. As such the CESE method is compatible with the simplest unstructured meshes and thus can be easily applied to solve problems with complex geometries. However, because the method uses space-time staggered stencils, solution decoupling may become a real nuisance in applications involving unstructured meshes. In this paper we will describe a simple and general remedy which, according to numerical experiments, has removed any possibility of solution decoupling. Moreover, in a real-world viscous flow simulation near a solid wall, one often encounters a case where a boundary with high curvature or sharp corner is surrounded by triangular/tetrahedral meshes of extremely high aspect ratio (up to 106). For such an extreme case, the spatial projection of a space-time compounded conservation element constructed using the original CESE design may become highly concave and thus its centroid (referred to as a spatial solution point) may lie far outside of the spatial projection. It could even be embedded beyond a solid wall boundary and causes serious numerical difficulties. In this paper we will also present a new procedure for constructing conservation elements and solution elements which effectively overcomes the difficulties associated with the original design. Another difficulty issue which was addressed more recently is the wellknown fact that accuracy of gradient computations involving triangular/tetrahedral grids deteriorates rapidly as the aspect ratio of grid cells increases. The root cause of this difficulty was clearly identified and several remedies to overcome it were found through a rigorous mathematical analysis. However, because of the length of the current paper and the complexity of mathematics involved, this new work will be presented in another paper.

Chang, Sin-Chung↗
NASA NTRS1998

Sand Shear Band Thickness Measurements by Digital Imaging Techniques

Digital imaging analysis was used to study localized deformations in granular materials tested under plane strain condition. Two independent techniques were applied and compared. In the first, the digitized optical images of a grid printed on the latex membrane were used to measure the shear band orientation angle and thickness, and were found to be 54.5' and 3.01 mm respectively. The second technique involved introducing an ultra-low viscosity resin into the specimen in preparation for thin- sectioning and microscopic study of the internal fabric. A total of 24 microscopic images obtained from four thin sections were analyzed and void ratio variation was measured. The shear band thickness measurements from images located along the shear band axis (at two locations) were equal to 3.19 mm and 3.29 mm which are very close to the average value obtained from surface analysis. The study was then extended to investigate the effects of sand grain-size and properties, specimen density, and confining pressure on shear band thickness. It was found that the normalized shear band thickness decreases as grain-size and confining pressure increase and as density decreases. Finally, shear band thickness is highly influenced by the specimen dilatancy.

Alshibli, Khalid A.↗
NASA NTRS2002

Glenn-HT: The NASA Glenn Research Center General Multi-Block Navier Stokes Heat Transfer Code

For the last several years, Glenn-HT, a three-dimensional (3D) Computational Fluid Dynamics (CFD) computer code for the analysis of gas turbine flow and convective heat transfer has been evolving at the NASA Glenn Research Center. The code is unique in the ability to give a highly detailed representation of the flow field very close to solid surfaces in order to get accurate representation of fluid beat transfer and viscous shear stresses. The code has been validated and used extensively for both internal cooling passage flow and for hot gas path flows, including detailed film cooling calculations and complex tip clearance gap flow and heat transfer. In its current form, this code has a multiblock grid capability and has been validated for a number of turbine configurations. The code has been developed and used primarily as a research tool, but it can be useful for detailed design analysis. In this presentation, the code is described and examples of its validation and use for complex flow calculations are presented, emphasizing the applicability to turbomachinery.

Gaugler, Raymond E.↗
NASA NTRS2001

Glenn-HT: The NASA Glenn Research Center General Multi-Block Navier-Stokes Heat Transfer Code

For the last several years, Glenn-HT, a three-dimensional (3D) Computational Fluid Dynamics (CFD) computer code for the analysis of gas turbine flow and convective heat transfer has been evolving at the NASA Glenn Research Center. The code is unique in the ability to give a highly detailed representation of the flow field very close to solid surfaces in order to get accurate representation of fluid heat transfer and viscous shear stresses. The code has been validated and used extensively for both internal cooling passage flow and for hot gas path flows, including detailed film cooling calculations and complex tip clearance gap flow and heat transfer. In its current form, this code has a multiblock grid capability and has been validated for a number of turbine configurations. The code has been developed and used primarily as a research tool, but it can be useful for detailed design analysis. In this paper, the code is described and examples of its validation and use for complex flow calculations are presented, emphasizing the applicability to turbomachinery for space launch vehicle propulsion systems.

Gaugler, Raymond E.↗
NASA NTRS2002

Glenn-HT: The NASA Glenn Research Center General Multi-Block Navier-Stokes Heat Transfer Code

For the last several years, Glenn-HT, a three-dimensional (3D) Computational Fluid Dynamics (CFD) computer code for the analysis of gas turbine flow and convective heat transfer has been evolving at the NASA Glenn Research Center. The code is unique in the ability to give a highly detailed representation of the flow field very close to solid surfaces in order to get accurate representation of fluid heat transfer and viscous shear stresses. The code has been validated and used extensively for both internal cooling passage flow and for hot gas path flows, including detailed film cooling calculations and complex tip clearance gap flow and heat transfer. In its current form, this code has a multiblock grid capability and has been validated for a number of turbine configurations. The code has been developed and used primarily as a research tool, but it can be useful for detailed design analysis. In this presentation, the code is described and examples of its validation and use for complex flow calculations are presented, emphasizing the applicability to turbomachinery.

Gaugfer, Raymond E.↗
NASA NTRS2022

A Central Asia Hydrologic Monitoring Dataset for Food and Water Security Applications in Afghanistan

From the Hindu Kush mountains to the Registan Desert, Afghanistan is a diverse landscape where droughts, floods, conflict, and economic market accessibility pose challenges for agricultural livelihoods and food security. The ability to remotely monitor environmental conditions is critical to support decision making for humanitarian assistance. The Famine Early Warning Systems Network (FEWS NET) Land Data Assimilation System (FLDAS) global and Central Asia data streams provide information on hydrologic states for routine integrated food security analysis. While developed for a specific project, these data are publicly available and useful for other applications that require hydrologic estimates of the water and energy balance. These two data streams are unique because of their suitability for routine monitoring, as well as for being a historical record for computing relative indicators of water availability. The global stream is available at ∼ 1-month latency, and monthly average outputs are on a 10 km grid from 1982–present. The second data stream, Central Asia (21–56°N, 30–100°E), at ∼ 1 d latency, provides daily average outputs on a 1 km grid from 2000–present. This paper describes the configuration of the two FLDAS data streams, background on the software modeling framework, selected meteorological inputs and parameters, and results from previous evaluation studies. We also provide additional analysis of precipitation and snow cover over Afghanistan. We conclude with an example of how these data are used in integrated food security analysis. For use in new and innovative studies that will improve understanding of this region, these data are hosted by U.S. Geological Survey data portals and the National Aeronautics and Space Administration (NASA). The Central Asia data described in this paper can be accessed via the NASA repository at https://doi.org/10.5067/VQ4CD3Y9YC0R (Jacob and Slinski, 2021), and the global data described in this paper can be accessed via the NASA repository at https://doi.org/10.5067/5NHC22T9375G (McNally, 2018).

Amy McNally↗
NASA NTRS1992

Adaptive explicit and implicit finite element methods for transient thermal analysis

The application of adaptive finite element methods to the solution of transient heat conduction problems in two dimensions is investigated. The computational domain is represented by an unstructured assembly of linear triangular elements and the mesh adaptation is achieved by local regeneration of the grid, using an error estimation procedure coupled to an automatic triangular mesh generator. Two alternative solution procedures are considered. In the first procedure, the solution is advanced by explicit timestepping, with domain decomposition being used to improve the computational efficiency of the method. In the second procedure, an algorithm for constructing continuous lines which pass only once through each node of the mesh is employed. The lines are used as the basis of a fully implicit method, in which the equation system is solved by line relaxation using a block tridiagonal equation solver. The numerical performance of the two procedures is compared for the analysis of a problem involving a moving heat source applied to a convectively cooled cylindrical leading edge.

Probert, E. J.↗
NASA NTRS2007

Statistical Analysis of the AIAA Drag Prediction Workshop CFD Solutions

The first AIAA Drag Prediction Workshop (DPW), held in June 2001, evaluated the results from an extensive N-version test of a collection of Reynolds-Averaged Navier-Stokes CFD codes. The code-to-code scatter was more than an order of magnitude larger than desired for design and experimental validation of cruise conditions for a subsonic transport configuration. The second AIAA Drag Prediction Workshop, held in June 2003, emphasized the determination of installed pylon-nacelle drag increments and grid refinement studies. The code-to-code scatter was significantly reduced compared to the first DPW, but still larger than desired. However, grid refinement studies showed no significant improvement in code-to-code scatter with increasing grid refinement. The third AIAA Drag Prediction Workshop, held in June 2006, focused on the determination of installed side-of-body fairing drag increments and grid refinement studies for clean attached flow on wing alone configurations and for separated flow on the DLR-F6 subsonic transport model. This report compares the transonic cruise prediction results of the second and third workshops using statistical analysis.

Joseph H Morrison↗
NASA NTRS1983

The value of residential photovoltaic systems: A comprehensive assessment

Utility-interactive photovoltaic (PV) arrays on residential rooftops appear to be a potentially attractive, large-scale application of PV technology. Results of a comprehensive assessment of the value (i.e., break-even cost) of utility-grid connected residential photovoltaic power systems under a variety of technological and economic assumptions are presented. A wide range of allowable PV system costs are calculated for small (4.34 kW (p) sub ac) residential PV systems in various locales across the United States. Primary factor in this variation are differences in local weather conditions, utility-specific electric generation capacity, fuel types, and customer-load profiles that effect purchase and sell-back rates, and non-uniform state tax considerations. Additional results from this analysis are: locations having the highest insolation values are not necessary the most economically attractive sites; residential PV systems connected in parallel to the utility demonstrate high percentages of energy sold back to the grid, and owner financial and tax assumptions cause large variations in break-even costs. Significant cost reduction and aggressive resolution of potential institutional impediments (e.g., liability, standards, metering, and technical integration) are required for a residential PV marker to become a major electric-grid-connected energy-generation source.

Borden, C. S.↗
NASA NTRS1999

Thermal Analysis of Magnetically-Coupled Pump for Cryogenic Applications

Magnetically-coupled pump is under evaluation at Kennedy Space Center for possible cryogenic applications. A major concern is the impact of low temperature fluid flows on the pump performance. As a first step toward addressing this and related issues, a computational fluid dynamics and heat transfer tool has been adopted in a pump geometry. The computational tool includes (i) a commercial grid generator to handle multiple grid blocks and complicated geometric definitions, and (ii) an in-house computational fluid dynamics and heat transfer software developed in the Principal Investigator's group at the University of Florida. Both pure-conduction and combined convection-conduction computations have been conducted. A pure-conduction analysis gives insufficient information about the overall thermal distribution. Combined convection-conduction analysis indicates the significant influence of the coolant over the entire flow path. Since 2-D simulation is of limited help, future work on full 3-D modeling of the pump using multi-materials is needed. A comprehensive and accurate model can be developed to take into account the effect of multi-phase flow in the cooling flow loop, and the magnetic interactions.

Senocak, Inanc↗
NASA NTRSDate not supplied

Human Systems Risk Network - A Ranking Analysis of Risks

INTRODUCTION The Human Systems Risk Board (HSRB) is responsible for understanding, managing, and mitigating the risks associated with spaceflight. For a particular mission, the HSRB assigns each human system risk a rating on a 5x5 grid assessing its likelihood and consequence, which is ultimately used to compare and rank the risks. The HSRB approaches risk management by primarily establishing the context of each human system risk individually with the understanding that mitigating one risk might affect the likelihood, consequence, and mitigation approaches of another. To support this effort the HSRB, subject matter experts, and risk custodian teams created directed acyclic graphs (DAG), often called a causal graph, for the twenty-nine risks. In this presentation, we propose a new ranking algorithm for the risks which includes the downstream influence of each risk according to the information in the DAGs and provide an application of graph theoretic tools. METHODS In 2014, Mindock and Klaus proposed a taxonomy for human system risk influences which we have adopted to categorize the nodes in each DAG. Analyzing the nodes that correspond to the risks in this taxonomy allows us to analyze and understand how each risk influences the others. We construct an auxiliary network, which we call the Primary Risk Network (PRN), where the nodes are the twenty-nine space flight risks and, a directed edge connects Risk A to Risk B if Risk A has some influence on the likelihood or consequence of Risk B as described in the DAGS. We perform a variety of graph theoretic ranking methods on the nodes (or risks) in the PRN, including Katz centrality. RESULTS We rank the nodes in the PRN using the Katz centrality score. The ten risks with the highest score are pictured in Figure 1, colored (light to dark) according to their score. We analyze other centrality measures like betweenness centrality, eigenvector centrality, and the Estrada index, and provide the meaning of the corresponding rankings in terms of the risks. Future work includes analyzing the other categories in the taxonomy defined by Mindock and Klaus [1]. For example, we are interested in analyzing the nodes that are labeled as countermeasures or capabilities and perform similar analysis to measure their effect on certain medical conditions.

dag↗