Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GaGe”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Experimental evaluation of stresses in spherically hollow balls

An analysis was undertaken to evaluate stresses within spherically hollow ball bearings proportioned for 40, 50, and 60% mass reductions. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models statically loaded in various orientations. Dimensionless results are reported for the balls under flate plate contact loads. Similitude considerations permit these results to be applied to calculate stresses in hollow ball bearings proportioned to these mass reductions.

Nypan, L. J.↗
NASA NTRS1972

Apollo 15 mission report. Supplement 2: Service propulsion system final flight evaluation

The command and service module 112 service propulsion system performance for the Apollo 15 mission was evaluated and found to be satisfactory. The following items were considered: (1) the steady-state performance as determined from analysis of the third and eight burns; (2) techniques, problems, and assumptions; (3) flight analysis results as compared to the preflight predicted performance; (4) the propellant utilization and gaging system operation; (5) the pressurization system performance; (6) transient data; and (7) revision of estimated propellant consumption.

Smith, R. J.↗
NASA NTRS1974

Bonded composite to metal scarf joint performance in an aircraft landing gear drag strut

The structural performance of a boron-epoxy reinforced titanium drag strut, which contains a bonded scarf joint and was designed to the criteria of the Boeing 747 transport, was evaluated. An experimental and analytical investigation was conducted. The strut was exposed to two lifetimes of spectrum loading and was statically loaded to the tensile and compressive design ultimate loads. Throughout the test program no evidence of any damage in the drag strut was detected by strain gage measurements, ultrasonic inspection, or visual observation. An analytical study of the bonded joint was made using the NASA structural analysis computer program NASTRAN. A comparison of the strains predicted by the NASTRAN computer program with the experimentally determined values shows excellent agreement. The NASTRAN computer program is a viable tool for studying, in detail, the stresses and strains induced in a bonded joint.

Howell, W. E.↗
NASA NTRS1974

Apollo 16, LM-11 descent propulsion system final flight evaluation

The performance of the LM-11 descent propulsion system during the Apollo 16 missions was evaluated and found satisfactory. The average engine effective specific impulse was 0.1 second higher than predicted, but well within the predicted one sigma uncertainty of 0.2 seconds. Several flight measurement discrepancies existed during the flight as follows: (1) the chamber pressure transducer had a noticeable drift, exhibiting a maximum error of about 1.5 psi at approximately 130 seconds after engine ignition, (2) the fuel and oxidizer interface pressure measurements appeared to be low during the entire flight, and (3) the fuel propellant quantity gaging system did not perform within expected accuracies.

Avvenire, A. T.↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics in the NAAL low speed wind tunnel (0A62b), volume 1

Experimental aerodynamic investigations were conducted on a sting-mounted 0.0405 scale representation of the 140A/B space shuttle orbiter in a 7.75 ft by 11 ft low speed wind tunnel during the time period from November 14, 1973, to December 6, 1973, with the primary test objectives being to establish basic longitudinal stability characteristics in and out of ground effect, as well as lateral-directional stability characteristics in free air. Two dual podded nacelle configurations were also tested, one with three dual podded nacelles on the lower wing surface, and the other with a single dual nacelle on the lower centerline with dual nacelle pylons mounted above each wing. Stability and control characteristics were investigated at nominal elevon, rudder, aileron, and body flap deflections. Pressure bugs were used to determine pressures on the vertical tail at spanwise stations, and aerodynamic force and moment data were measured in the stability axis system by an internally mounted, six component strain gage balance.

Mennell, R.↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics in the NAAL low speed wind tunnel (OA62B), volume 2

Experimental aerodynamic investigations were conducted on a sting-mounted 0.0405 scale representation of the 140A/B space shuttle orbiter in a 7.75 ft by 11 ft low speed wind tunnel during the period from November 14, 1973 to December 6, 1973. Establishment of basic longitudinal stability characteristics in and out of ground effect, and the establishment of lateral-directional stability characteristics in free air were the primary test objectives. The following effects and configurations were tested: (1) two dual podded nacelle configurations; (2) stability and control characteristics at nominal elevon deflections, rudder deflections, airleron deflections, rudder flare angles, and body flap deflections; (3) effects of various elevon and elevon/fuselage gaps on longitudinal stability and control; (4) pressures on the vertical tail at spanwise stations using pressure bugs; (5) aerodynamic force and moment data measured in the stability axis system by an internally mounted, six-component strain gage balance. For Vol. 1, see N74-32324.

Mennell, R.↗
NASA NTRS1974

Stability and control characteristics for the inner mold line configuration of the space shuttle orbiter (OA110)

Experimental aerodynamic investigations were conducted on a sting mounted 0.0405-scale representation of the -140A/B inner mold line (IML) space shuttle orbiter in 7.75 x 11 foot low speed wind tunnel, during the time period from 18 March 1974 to 20 March 1974. The primary test objectives were to establish basic longitudinal and lateral-directional stability and control characteristics for the IML orbiter. Additional configurations investigated were sealed elevon hingeline gaps, sealed rudder split line and hingeline gaps, larger radius leading edge on the vertical tail, and sealed speedbrake base. Aerodynamic force and moment data for the orbiter were measured in the body-axis system by an internally mounted, six-component strain gage balance. The model was sting mounted with the center of rotation located at approximately the wing trailing edge. The nominal angle of attack range was from -4 to +30 degrees. Yaw polars were recorded over a nominal yaw angle range from -14 to +14 degrees at constant angles of attack of 0, + or - 5, 10, 15 and 20 degrees.

Hughes, T.↗
NASA NTRS1974

Investigation of space shuttle orbiter subsonic stability and control characteristics and determination of control surface hinge moments in the Rockwell International low speed wind tunnel (OA37)

Experimental aerodynamic investigations were conducted on a string-mounted 0.030 scale representation of the 140A/B space shuttle orbiter in the 7.75- by 11-foot low speed wind tunnel. The primary test objectives were to establish basic longitudinal and lateral directional stability and control characteristics for the basic configuration plus control surface hinge moments. Aerodynamic force and moment data were measured in the body axis system by an internally mounted, six-component strain gage balance. Additional configurations investigated were sealed rudder hingeline gaps, sealed elevon gaps and compartmentized speedbrakes.

Hughes, T.↗
NASA NTRS1974

Design, fabrication, and test of lightweight shell structure, phase 2

A cylindrical shell skirt structure 4.57 m (180 in.) in diameter and 3.66 m (144 in.) high was subjected to a design and analysis study using a wide variety of structural materials and concepts. The design loading of 1225.8 N/cm (700 lb/in.) axial compression and 245.2 N/cm (140 lb/in.) torsion is representative of that expected on a typical space tug skirt section. Structural concepts evaluated included honeycomb sandwich, truss, isogrid, and skin/stringer/frame. The materials considered included a wide variety of structural metals as well as glass, graphite, and boron-reinforced composites. The most unique characteristic of the candidate designs is that they involve the use of very thin-gage material. Fabrication and structural test of small panels and components representative of many of the candidate designs served to demonstrate proposed fabrication techniques and to verify design and analysis methods.

Source record↗
NASA NTRS1974

Experimental evaluation of stresses in cylindrically hollow (drilled) balls

An experimental stress analysis was undertaken to evaluate stresses within cylindrically hollow (drilled) bearing balls proportioned for 40, 50, and 60 percent mass reductions. Strain gage rosettes were used to determine principal strains and stresses in the steel ball models statically loaded in various orientations. Results are reported for 127 mm OD balls under 44,500 N loads. Similitude considerations permit these results to be applied to calculate stresses in actual size drilled bearing balls proportioned to these mass reductions.

Nypan, L. J.↗
NASA NTRS1974

Solid state power controllers

Solid state power controllers (SSPC's) are to be considered for use as replacements of electromechanical relays and circuit breakers in future spacecraft and aircraft. They satisfy the combined function of both the relay and circuit breaker and can be remotely controlled by small signals, typically 10 mA, 5 to 28 v(dc). They have the advantage over conventional relay/circuit breaker systems in that they can be located near the utilization equipment and the primary ac or dc bus. The low level control, trip indication and status signals can be circuited by small gauge wire for control, computer interface, logic, electrical multiplexing, onboard testing, power management, and distribution purposes. This results in increased system versatility at appreciable weight saving and increased reliability. Conventional systems require the heavy gage load wiring and the control wiring to be routed from the bus to the load to other remote relay contacts, switches, sensors, etc. and to the circuit breaker located in the flight engineer's compartment for purposes of manual reset.

Gibbs, R. S.↗
NASA NTRS1974

Miniature load cell instrumentation for finite deformation biaxial testing of elastomers

Accuracy of biaxial test equipment to examine the nonlinear mechanical behavior of thin sheet specimens of elastomeric materials has been hampered by lack of precise determination of the force distribution along the sides of the specimen. It has been necessary to use an effective width established by approximate means to obtain the stress from the overall force applied along the edges. To avoid this experimental difficulty, individual miniature proof-ring load cells utilizing semiconductor strain gages have been developed and applied to the support hooks for the thin sheet specimens. Typical results are shown for time-dependent stress distributions for all degrees of biaxiality. An accurate evaluation of the effective specimen width is now possible.

Arenz, R. J.↗
NASA NTRS1974

Test results from the Langley high Reynolds number cryogenic transonic tunnel

NASA has recently developed and proof tested a pilot cryogenic transonic pressure tunnel. In addition to providing an attractive method for obtaining high Reynolds number results at moderate aerodynamic loadings and tunnel power, this unique facility enables the independent determination of the effects of Reynolds number, Mach number, and aeroelasticity. The proof-of-concept experimental and theoretical studies are briefly reviewed. Experimental results are included which indicate pressure distributions for a two-dimensional airfoil and strain-gage balance characteristics for a three-dimensional delta wing model.

Ray, E. J.↗
NASA NTRS1974

A technique for generating shear waves in cylindrical shells under radial impact

Experimental techniques are developed to study and measure the shear-wave velocity in an aluminum cylindrical shell subjected to a radial impact. The radial impact is obtained by exploding an electrical detonator inserted in plastic plugs mounted on the end of the shell. Strain gages, mounted on the outside surface of the shell at various axial locations, are used to obtain oscilloscope traces from which the shear-wave velocity can be calculated.

Blum, A.↗
NASA NTRS1974

Experimental study of the shock-induced unsteady laminar boundary layer on a flat plate

The behavior of the unsteady laminar boundary layer induced by the incident shock wave passing over a flat plate mounted in a shock tube has been experimentally studied for shock speeds ranging from 2.35 to 7.34 km/sec by measuring unsteady heat transfer rates to the plate using thin-film heat-flux gages. Theoretical heat-transfer rates were predicted from analytical solutions in the literature which describe the unsteady flat plate boundary layer development for equilibrium real-gas flows. Experimental results obtained for both air and nitrogen were found to be in good agreement with the theoretical predictions.

Cook, W. J.↗
NASA NTRS1974

Effect of ELEVON gap configurations on the longitudinal stability and control effectiveness of the 43-0 space shuttle orbiter (OA118)

Experimental aerodynamic investigations were conducted on a stingmounted 0.0405-scale representation of the 140A/B space shuttle orbiter in a 7.75 by 11-Foot low speed wind tunnel from April 24 to April 26, 1974. Differential inboard/outboard elevon panel deflections with the 6-inch gap were investigated to determine outboard panel aileron effectiveness. The elevons were deflected from +20 degrees to -40 degrees in various combinations. Aerodynamic force and moment data for the orbiter were measured in the body axis system by an internally mounted, six-component strain gage balance. The model was sting mounted with the center of rotation located at F.S. 60.172. The angle of attack range was from -10 degrees to +24 degrees.

Hughes, T.↗