Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuels Development”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

High temperature steam oxidation dynamics of U 3 Si 2 with alloying additions: Al, Cr, and Y

Uranium silicides are considered for advanced technology reactor fuels due to their enhanced thermal conductivity and high uranium density (U 3 Si and U 3 Si 2 ) compared to traditional UO 2 . Susceptibility to oxidation and wash out, in the event of a cladding breech, could limit the potential for deployment of silicides as accident tolerant fuels. Mitigating the water reaction for U 3 Si 2 could enable its use as an accident tolerant, high uranium density fuel or as a composite fuel constituent. Reported here is the impact of alloying additions of Al, Cr and Y on the high temperature, steam oxidation response of U 3 Si 2 . In addition to the thermogravimetric response, as melted microstructures, phase compositions and post oxidation analysis are also presented. Here, the investigation shows steam oxidation dynamics are altered, from non-alloyed U 3 Si 2 , under thermally ramped conditions. However, additional alloy development of these fuel forms is necessary for further consideration as candidate accident tolerant fuels in water-cooled reactor designs.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Community Engagement - A Citizen-Centric Approach to Seeking a Social License - 20017

The long regulatory road has finally been completed-after years of effort a Record of Decision has been signed and a Permit to Construct has been granted or a Permit to Operate has been obtained. But what about the other road that should be taken in parallel-community engagement? Working with the public is not a sequential activity, rather it is a consequential one and needs to be integrated with overall project planning. Unless you have effectively, meaningfully, and patiently engaged with the project's communities of impact, you may find your project trying to obtain a social license or a social license to operate (SLO). The SLO has its origins in the mining industry and its roots in the business model of corporate social responsibility and sustainability. These latter practices are well known to the US DOE and its contractor community. Aspects of the SLO are emerging as individuals and communities are becoming more informed and have increased expectations for being able to influence and shape decisions. When local community issues are not sought out, listened to, or addressed early, and questions are left unanswered, they can become agenda items for larger unaffiliated groups, and project loss (through delays and/or cancellation) can occur. Issues can transition from resolvable to intractable, a type of SLO face-off. Social media campaigns, serial negative media coverage, and protest signs at project sites opposing regulatory decisions already made are no longer anomalies. These types of incidents demonstrate the increasingly delicate relationship between approved regulatory/technical decisions and public acceptance of those decisions. A SLO is not a requirement. However, the building-blocks of a SLO - working with members of affected communities to build understanding, potentially to obtain and maintain community acceptance or even gain approval or support - are evidence of leadership by project sponsors. Actions taken, or not taken, by project sponsors truly have the ability to influence an outcome. While projects are not assured of success or failure, engaging the community in an empowered process is an investment of time and resources toward success for the project and thus for the communities of impact. Authors Note: Extensive literature searches were performed in developing this paper. The majority of the published literature on SLO as a 'movement' was found from sources in Canada, the European Union (Germany and France in particular), South Asia, South Korea, and many Latin American countries. The literature addressed resource development (mining), infrastructure, and energy projects. Articles written by US sources often spoke to origins and structural theory, specific project issues such as Not in My Back Yard (NIMBY) and to protests/demonstrations related to those projects, rather than systemic opposition/conflict phenomena. For these reasons many international SLO experiences and sources are cited in the discussion. The authors recognize these non-US experiences with SLO as having a 'forecast' value to US projects, especially those related to nuclear projects of any type, waste treatment and disposal, energy development (especially fossil fuels as well as alternative sources), mining, and infrastructure. The body of future SLO experiences in the US will shape the future responses to it. (authors)

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

X-ray-based technologies in emerging fuel cell research

The workshop titled `X-ray-based technologies in emerging fuel cell research', organized by Vivian Stojanoff from Brookhaven National Laboratory (BNL) and Narayanasami Sukumar from Cornell University/Advanced Photon Source-Northeastern Collaborative Access Team, was a notable segment of the National Synchrotron Light Source II and Center for Functional Nanomaterials Users' Meeting held 13–17 May 2024. This one-day event, on 13 May 2024, at BNL in New York, aimed to bring together researchers, beamline scientists, management and developers to propel fuel cell technology forward using model systems inspired by natural photosynthesis and redox enzymes. Furthermore, this summary encapsulates the key discussions, advancements and future implications of the workshop.

Xray↗
DOE OSTI2022

Fuel Specification for Uranium Monocarbide FAST Fuel Specimens

This specification outlines the fabrication requirements for kernel compact uranium monocarbide (UC) fuel to be fabricated at General Atomics (GA) and is already issued in EDMS and is going thru LRS so that it can be shared with the Vendor. The UC fuel will be irradiated in the Advanced Test Reactor (ATR) using the Irradiation System for High-Throughput Acquisition (ISHA-1). The primary objective of the ISHA-1 capsule design is to deliver to Idaho National Lab (INL) a semi-universal drop-in capsule that can facilitate the irradiation of both fissile and structural materials in a variety of ATR positions. This irradiation experiment will support the need for development of Accelerated Fuel Qualification (AFQ) methods.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Draft Experimental Plan for Commercial SNF Degradation in Repository Environments with a Focus on Fracture Matrix Degradation

This report documents work performed supporting US Department of Energy (DOE) Nuclear Energy Spent Fuel and Waste Disposition, Spent Fuel and Waste Science and Technology, under work breakdown structure element 1.08.01.03.04, “Inventory and Waste Form Characteristics and Performance.” In particular, this report fulfills the M3 milestone, M3SF-21OR010309072 "Draft Experimental Plan for Commercial SNF Degradation in Repository Environments” as described in work package SF-21OR01030907 "SNF Degradation Testing-ORNL".This experimental plan is a collaboration between ORNL, SNL, ANL, and PNNL. It is intended to support source term model development and spent fuel degradation testing in a range of generic repository conditions. Potential testing and experiments to support validation of the Fuel Matrix Dissolution Model (FMDM) and the overall development/validation of repository source term modeling are discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Electroanalytical Sensors for Liquid Fueled Fluoride Molten Salt Reactor

ThorCon is developing a thermal thorium / uranium molten salt fueled reactor that uses a fuel salt consisting of NaF - BeF 2 - ThF 4 - UF 4 - UF 3 , which uses 19.75% enriched uranium. It is not a breeder reactor but requires regular additions of fissile material. On-site fuel processing is limited to adding make-up fuel, and adding beryllium to maintain redox balance in the fuel salt. The fluoride salt is an excellent flux that will strip the protective oxygen away from all metal surfaces it contacts. In order to protect the metal surfaces in the primary loop, no free fluorine is allowed. Maintaining a ratio of UF 4 to UF 3 provides a chemical buffer that can absorb any free fluorine released during the fission process before it can harm the structure. Periodic additions of metallic beryllium to the fuel salt will react with UF 4 to form BeF 2 and UF 3 , which will maintain the desired UF 4 /UF 3 ratio. A means to measure the UF 4 /UF 3 ratio is important to maintain the fuel salt in a non-corrosive state and could also provide additional insight into the corrosion behavior and chemical constitution of the system. A promising measurement technique is based on electrochemistry.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1989

SSME Alternate Turbopump Development Program: Design verification specification for high-pressure fuel turbopump

The design and verification requirements are defined which are appropriate to hardware at the detail, subassembly, component, and engine levels and to correlate these requirements to the development demonstrations which provides verification that design objectives are achieved. The high pressure fuel turbopump requirements verification matrix provides correlation between design requirements and the tests required to verify that the requirement have been met.

Source record↗
DOE OSTI2023

Decarbonization of Liquid Heating Fuels

Annually, residential and commercial buildings use about 5 billion gallons (18.9 billion liters) of distillate fuel for space and water heating. There is considerable interest in decarbonizing these markets through a combination of heat pumps and a future, carbon-free grid. An alternate approach that offers rapid and cost effective decarbonization involves substitution of low-carbon biofuels for fossil fuels within this market. Heating fuel marketers in North America and Europe are aggressively moving to achieve market penetration of biofuels. Processes for this include fuel specification standards, development of manufacturer-approved burners and all system components, development of standards for equipment listing, installation code changes, and generation of performance data. There has been considerable progress in these areas and each of these are reviewed in this paper. Currently, the most important biofuel for this market is biodiesel with a U.S. production capacity of 2.4 billion gallons (9.1 billion liters) and approximately a 75% reduction in GHG emissions. The biodiesel industry has stated a vision for dramatic increases in biodiesel production over the next decades. Fuel and equipment standards are in place to enable use of biodiesel blends to 20% and this blend is now widely used. Standard changes to extend this to as high as 100% biodiesel are nearing completion. Several states have implemented requirements for minimum levels of biodiesel in heating oil with these levels increasing over time.

09 BIOMASS FUELS↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this paper are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

Accident Tolerant Fuels↗
DOE OSTI2025

Evaluation of an Accident Tolerant Fuel Leak in the Advanced Test Reactor

Accident Tolerant Fuels (ATF), which are nuclear fuel sources designed to withstand operational irregularities and incidents, have been a topic of interest in the nuclear industry for several decades. Interest in ATF technology surged following the 2011 accident at Fukushima Daiichi in Japan. At the Advanced Test Reactor (ATR), one of Idaho National Laboratory’s (INL) four operating nuclear reactors, the ATF program is a collaborative effort between the national laboratory and various stakeholders within the nuclear industry. This program focuses on the research and development of novel fuel compositions, cladding, and component materials with enhanced accident-resistant properties. During one of ATR’s 60-day operating cycles in 2024, the reactor experienced five unplanned shutdowns. Following the fifth shutdown, radiation monitors detected an increase in radiation levels coming from the loop piping. Subsequent water samples confirmed the cause was a leak of fission products from the ATF experiment, designated as ATF-2C. The source of the leak was identified as the instrumented section of the test train. The primary discussions in this presentation are 1) the design of the ATF test train, 2) the operating parameters leading up to and following the detection of the leak, and 3) the quantification and characterization of the released fission products.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Advanced Multi-Tube Mixer Combustion for 65% Efficiency (Final Report)

This project targeted advanced low NOx combustion for advanced gas turbines capable of 65%, or greater, efficiency in combined cycle application. This technology advancement has further potential to benefit gas turbines used in coal based IGCC applications with pre-combustion carbon capture and hydrogen as the resulting fuel. The program developed and synthesized the most advanced combustion system capable of achieving low NOX emissions up to turbine inlet temperatures of 3100F while also supporting the load-following needs of a modern grid. The combustion system contributes to the overall gas turbine efficiency goal by setting the maximum cycle temperature achievable for a given NOX level and by minimizing the through-combustor air flow pressure drop. Focus areas for this project targeted maximizing the turbine inlet temperature entitlement, as constrained by emissions considerations. The design also minimized parasitic air flow pressure drop by using advanced cooling techniques and performance materials selections and by minimizing hot surface area. These two technology objectives (maximum, emissions-compliant cycle temperature and minimum air flow pressure drop) were integrated into a prototype design. The primarily analytical project sought to identify the most promising technologies to meet these objectives. Additional critical “jugular” data were obtained from multi-tube mixer tests to realize the potential of leveraging “micro flames” for minimizing overall hot surface area. This data was used, in conjunction with an understanding of advanced material and cooling design technologies, to analytically develop multiple design concepts. Phase I focused on in-depth engineering analysis and design, with minimal supporting laboratory testing to enable a selection of the top three combustion architectures for achieving these overall objectives. Phase II of the program developed the selected design through a combination of sub-scale testing and analytical efforts. Early tests included a cold-flow cascade to establish aerodynamic performance characteristics and a sub-scale fired test at GE Global Research in Niskayuna, NY, to establish cooling and heat transfer characteristics in conjunction with combustion performance. The data from these tests validated the analytical models to ultimately design a full-scale, test article to evaluate at prototypical pressure and temperature conditions at GE Gas Power’s Gas Turbine Technology Laboratory in Greenville, SC. GE Gas Power also developed, tested, and recommended a suitable seal design to be applied to the unique features of the combustor. To assess the technology challenges from prospective future production of the combustor from a ceramic matrix composite material, screening tests of Environmental Barrier Coatings were completed.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1992

H2-fueled high-bypass turbofan

The study developed preliminary design concepts for the exploitation of the properties of LH2 in a turbofan engine intended for air transport use, and showed the benefits which accrue in reduction of aircraf direct operating cost. Design concepts for the engine fuel delivery and control system, including the engine high pressure fuel pump, were developed, and general concept feasibility was shown. For both the engine and the fuel delivery and control system, recommendations were made for the advanced development which is necessary to bring the technology to a state of readiness for design application. The study was of necessity abbreviated in nature: more intensive study of both the engine and fuel delivery and control system is recommended.

Riple, J. C.↗
NASA NTRS1996

Space Electrochemical Research and Technology

Individual papers presented at the conference address the following topics: development of a micro-fiber nickel electrode for nickel-hydrogen cell, high performance nickel electrodes for space power application, bending properties of nickel electrodes for nickel-hydrogen batteries, effect of KOH concentration and anions on the performance of a Ni-H2 battery positive plate, advanced dependent pressure vessel nickel hydrogen spacecraft cell and battery design, electrolyte management considerations in modern nickel hydrogen and nickel cadmium cell and battery design, a novel unitized regenerative proton exchange membrane fuel cell, fuel cell systems for first lunar outpost - reactant storage options, the TMI regenerable solid oxide fuel cell, engineering development program of a closed aluminum-oxygen semi-cell system for an unmanned underwater vehicle, SPE OBOGS on-board oxygen generating system, hermetically sealed aluminum electrolytic capacitor, sol-gel technology and advanced electrochemical energy storage materials, development of electrochemical supercapacitors for EMA applications, and high energy density electrolytic capacitor.

Richard M Wilson↗
DOE OSTI2024

The HyRIGHT Project: 700 bar Hydrogen Refueling Interface for Gaseous Heavy-Duty Trucks

Heavy duty truck fueling places additional constraints on the station. The HyRIGHT project was developed to evaluate a subset of key areas around precooling, communications, and safety risks that aims to:  Utilize a dynamic model that includes the relevant station components and vehicle to develop an optimized precooling strategy based on initial precooling status, real time communications that can support fueling protocol development.  Perform a techno economic cost assessment (TEA) related to effects of precooling including station storage and efficiency effects.  Develop a Cyber Vulnerability assessment and framework for refueling of HD vehicles with station communications.  Disseminate the results in support of the HD fueling protocol development to the relevant standards development organizations.

JAMES, Charles W.↗
DOE OSTI2021

Post-irradiation examination of legacy high burnup fuel to support safety testing

Safety/transient testing to evaluate performance under off-normal conditions is an essential pillar for both the development of Accident Tolerant Fuels (ATF) and the optimization of fuel operation economics beyond current discharge burnups. Among other factors, the successful interpretation of the transient testing results relies upon the knowledge of the initial conditions of the test, including the characteristics of the fuel system under scrutiny. When testing pre-irradiated material, the assumptions that the fuel and the cladding still have the same properties as in the pre-irradiation stage is obviously wrong and could affect the results of the test. This is particularly true the more burnup accumulates in the fuel rod and irradiation progresses. The knowledge of the initial microstructure of both fuel and cladding allows a clearer interpretation of the subsequent transient testing results, provides validation of the physical phenomena underlying the model predictions and eliminates the uncertainties related to the limited knowledge of the sample status before the test. One example is the phenomenon of fine fragmentation that occurs in Light Water reactor (LWR) fuel. During a Loss of Coolant Accident (LOCA) or Reactivity Initiated Transient (RIA) the fuel can severely fragment. During LOCA, high burnup fuel tend to finely fragment, which has raised safety concerns due to the increased likelihood of dispersal of such small particles once the cladding has burst and due to the increased fission gas release. Therefore, efforts have been devoted to the assessment of a pulverization threshold that could determine the conditions under which fine fragmentation is predominant. However, the lack of information regarding the initial conditions of the fuel, and the connections between those conditions and the pre-transient irradiation history, have hindered the development of a fully mechanistic fragmentation and pulverization criterion. The empirical relationships rely on conservative estimations, due to the lack of information on critical material properties and characteristics. More generally, experimental evidence of the irradiation-induced modifications at microstructural scale are necessary to determine the behavior of the material at the macroscopic scale, with the latter being the one of technological interest. Significant progress has been made in the last two decades in the developments of analytical materials science techniques that can be applied to highly radioactive materials, such as high burnup fuels. The availability of new techniques and the improvement of existing ones has enabled investigations previously not possible that can deepen the understanding of the fuel characteristics and properties at high burnup. The better knowledge of material behavior and irradiation-induced phenomena could help the prediction of its performance. In this context, the scope of the present work is to apply a wide portfolio of advanced characterization techniques to determine properties that are relevant for safety and performance. The results are interpreted in the context of engineering scale post-irradiation examinations and available information on the irradiation conditions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Numerical Investigation of Fuel Property Effects on Mixed-Mode Combustion in a Spark-Ignition Engine

In this research, lean mixed-mode combustion is numerically investigated using computational fluid dynamics (CFD) in a spark-ignition engine. A new E30 fuel surrogate is developed using a neural network model with matched octane numbers. A skeletal mechanism is also developed by automated mechanism reduction and by incorporating a NO x submechanism. A hybrid approach that couples the G-equation model and the well-stirred reactor model is employed for turbulent combustion modeling. The developed CFD model is shown to well predict pressure and apparent heat release rate (AHRR) traces compared with experiment. Two types of combustion cycles (deflagration-only and mixed-mode cycles) are observed. The mixed-mode cycles feature early flame propagation and subsequent end-gas auto-ignition, leading to two distinctive AHRR peaks. The validated CFD model is then employed to investigate the effects of NO x chemistry. The NO x chemistry is found to promote auto-ignition through the residual gas, while the deflagration phase remains largely unaffected. Sensitivity analysis is finally performed to understand effects of fuel properties, including heat of vaporization (HoV) and laminar flame speed (S L ). An increased HoV tends to suppress auto-ignition through charge cooling, while the impact of HoV on flame propagation is insignificant. In contrast, an increased S L is found to significantly promote both flame propagation and end-gas auto-ignition. The promoting effect of S L on auto-ignition is not a direct chemical effect; it is rather caused by an advancement of the combustion phasing, which increases compression heating of the end-gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Perspective on Solar Energy Materials, Design and Discovery, Defects, Disorder, and Interfaces

The energy transition still faces a daunting math. Currently, more than three quarters of final energy consumption occurs in form of fuels vs less than one quarter in electricity. On the other hand, renewable energy additions come almost exclusively in the form of electricity (dominantly photovoltaics and wind). Thus, meeting the terawatt challenge requires enormous growth in renewables, sufficient to convert excess electricity into fuels, as well as the development of non-electricity based solar fuel technologies, for example via solar thermochemical routes. In this presentation, we will review successes and challenges in photovoltaic materials from silicon to CdTe to halide perovskites and potential emerging materials, with a particular perspective on the role of first principles calculations and predictions. Materials design and discovery is evolving to incorporate defects, disorder, and interfaces. These phenomena play also an important role in the thermochemical generation of hydrogen, allowing to utilize synergies between renewable electricity and fuels in computational research. At the same time, machine learning approaches are increasingly geared toward properties of non-ideal materials, for example defect formation, allowing the screening for more complex material behavior as needed for the respective applications.

fuels↗