Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fuel Cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

A durable polyvinyl butyral-CsH 2 PO 4 composite electrolyte for solid acid fuel cells

We report a composite electrolyte membrane composed of polyvinyl butyral (PVB) and CsH 2 PO 4 has been prepared via a facile and cost-effective method for solid acid fuel cells. The effect of PVB content on conductivity, mechanical integrity, and fuel cell performance is investigated. A minimum amount of 3 wt% PVB in the CsH 2 PO 4 -based composite electrolyte not only offers the required mechanical integrity but also allows high conductivity (~28 mS cm -1 at 260 °C). Single cells based on the composite electrolytes demonstrate a peak power density of 108 mW cm -2 at 260 °C. Almost no degradation in electrochemical performance could be observed during the stability test for 10 h and three thermal-cycling test in H 2 /O 2 fuel cell, indicating the promising application of the composite electrolyte in solid acid fuel cells.

25 ENERGY STORAGE↗

Fuel Cell Buses in U.S. Transit Fleets: Current Status 2020

This report summarizes the progress of fuel cell electric bus (FCEB) development in the United States and discusses the achievements and challenges of introducing fuel cell propulsion in transit. The report provides a summary of results from evaluations performed by the U.S. Department of Energy's (DOE's) National Renewable Energy Laboratory (NREL). The 2020 summary results primarily focus on the most recent data on these FCEBs, from January 2020 through July 2020. The primary results presented in the report are from 25 FCEBs deployed at three agencies: Alameda-Contra Costa Transit District (AC Transit) in Oakland, California (10 FCEBs); Orange County Transportation Authority (OCTA) in Santa Ana, California (10 FCEBs); SunLine Transit Agency in Thousand Palms, California (5 FCEBs).

08 HYDROGEN↗

A fuel cell energy storage system for Space Station extravehicular activity

The development of a fuel cell energy storage system for the Space Station Extravehicular Mobility Unit (EMU) is discussed. The ion-exchange membrane fuel cell uses hydrogen stored as a metal hydride. Several features of the hydrogen-oxygen fuel cell are examined, including its construction, hydrogen storage, hydride recharge, water heat, water removal, and operational parameters.

Rosso, Matthew J., Jr.↗

A Novel Non-Platinum Group Electrocatalyst for PEM Fuel Cell Application

Precious-metal catalysts (predominantly Pt or Pt-based alloys supported on carbon) have traditionally been used to catalyze the electrode reactions in polymer electrolyte membrane (PEM) fuel cells. However as PEM fuel systems begin to approach commercial reality, there is an impending need to replace Pt with a lower cost alternative. The present study investigates the performance of a carbon-supported tantalum oxide material as a potential oxygen reduction reaction (ORR) catalyst for use on the cathode side of the PEM fuel cell membrane electrode assembly. Although bulk tantalum oxide tends to exhibit poor electrochemical performance due to limited electrical conductivity, it displays a high oxygen reduction potential; one that is comparable to Pt. Analysis of the Pourbaix electrochemical equilibrium database also indicates that tantalum oxide (Ta2O5) is chemically stable under the pH and applied potential conditions to which the cathode catalyst is typically exposed during stack operation. Nanoscale tantalum oxide catalysts were fabricated using two approaches, by reactive oxidation sputtering and by direct chemical synthesis, each carried out on a carbon support material. Nanoscale tantalum oxide particles measuring approximately 6nm in size that were sputtered onto carbon paper exhibited a mass-specific current density as high as one-third that of Pt when measured at 0.6V vs. NHE. However because of the two-dimensional nature of this particle-on-paper structure, which limits the overall length of the triple phase boundary junctions where the oxide, carbon paper, and aqueous electrolyte meet, the corresponding area-specific current density was quite low. The second synthesis approach yielded a more extended, three-dimensional structure via chemical deposition of nanoscale tantalum oxide particles on carbon powder. These catalysts exhibited a high ORR onset potential, comparable to that of Pt, and displayed a significant improvement in the area-specific current density. Overall, the highest mass-specific current density of the carbon-powder supported catalyst was ~ 9% of that of Pt.

30 DIRECT ENERGY CONVERSION↗

Advances in solid polymer electrolyte fuel cell technology with low-platinum-loading electrodes

The Gemini Space program demonstrated the first major application of fuel cell systems. Solid polymer electrolyte fuel cells were used as auxiliary power sources in the spacecraft. There has been considerable progress in this technology since then, particularly with the substitution of Nafion for the polystyrene sulfonate membrane as the electrolyte. Until recently the performance was good only with high platinum loading (4 mg/sq cm) electrodes. Methods are presented to advance the technology by (1) use of low platinum loading (0.35 mg/sq cm) electrodes; (2) optimization of anode/membrane/cathode interfaces by hot pressing; (3) pressurization of reactant gases, which is most important when air is used as cathodic reactant; and (4) adequate humidification of reactant gases to overcome the water management problem. The high performance of the fuel cell with the low loading of platinum appears to be due to the extension of the three dimensional reaction zone by introduction of a proton conductor, Nafion. This was confirmed by cyclic voltammetry.

Srinivasan, Supramaniam↗

Boosting Fuel Cell Performance with Accessible Carbon Mesopores

We present that heavy use of scarce Pt in the electrodes poses a barrier to the application of proton exchange membrane fuel cells (PEMFCs) for transportation. Although some automakers can now commercialize fuel cell electric vehicles (FCEVs) with as little as 30 g of Pt, this is still substantially more than what incumbent internal combustion engine vehicles use (2-8 g of precious metals). A long-term target of <5 g of Pt-group metals per vehicle is probably needed to be sustainable. Since W. R. Grove’s invention of the fuel cell in 1839, most breakthroughs in fuel cell performance have been associated with an increase in the so-called three-phase interface—the interface where the reactant gas meets electrons in the solid phase and protons in the electrolyte phase. Pt is made into nanoparticles and supported on carbon black to increase the mass-specific Pt surface area and to secure large pores for reactant oxygen gas to access Pt. Solid electrolyte such as the perfluorosulfonic acid (PFSA) ionomer is blended with the catalyst to carry protons to the Pt surface. Lastly, despite a long history of maximizing the three-phase interfacial area, one must realize that an optimized three-phase interface does not equal a maximum Pt/ionomer interface area.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Rheological Investigation on the Microstructure of Fuel Cell Catalyst Inks

We present a rheological investigation of fuel cell catalyst inks. The effects of ink parameters, which include carbon black-support structure, Pt presence on carbon support (Pt-carbon), and ionomer (Nafion) concentration, on the ink microstructure of catalyst inks were studied using rheometry in combination with ultrasmall-angle X-ray scattering (USAXS) and dynamic light scattering (DLS). Dispersions of a high-surface-area carbon (HSC), or Ketjen black type, demonstrated a higher viscosity than Vulcan XC-72 carbon due to both a higher internal porosity and a more agglomerated structure that increased the effective particle volume fraction of the inks. The presence of Pt catalyst on both the carbon supports reduced the viscosity through electrostatic stabilization. For carbon-only dispersions (without Pt), the addition of ionomer up to a critical concentration decreased the viscosity due to electrosteric stabilization of carbon agglomerates. However, with Pt-carbon dispersions, the addition of ionomer showed contrasting behavior between Vulcan and HSC supports. In the Pt-Vulcan dispersions, the effect of ionomer addition on the rheology was qualitatively similar to Vulcan dispersions without Pt. The Pt-HSC dispersions showed an increased viscosity with ionomer addition and a strong shear-thinning nature, indicating that Nafion likely flocculated the Pt-HSC aggregates. These results were verified using DLS and USAXS. Further, the observations of the effect of ionomer:carbon ratio and a comparison between carbons of different surface areas provided insights on the microstructure of the catalyst ink corresponding to the optimized I/C ratio for fuel cell performance reported in the literature.

36 MATERIALS SCIENCE↗

Mass transfer in fuel cells

Results of experiments on electron microscopy of fuel cell components, thermal decomposition of Teflon by thermogravimetry, surface area and pore size distribution measurements, water transport in fuel cells, and surface tension of KOH solutions are described.

Walker, R. D., Jr.↗

In-line, High-Throughput Quality Monitoring for Fuel Cell and Electrolyzer Components Based on Transmission and Reflection Imaging

During the manufacturing of fuel cell and electrolyzer membranes and membrane electrode assemblies (MEAs), real-time, in-line, high-throughput optical-based quality monitoring methods are essential for detecting defects and monitoring thickness variations, thus improving the performance and increasing the durability of fuel cell and electrolyzer in the hydrogen industry. For the MEAs with very opaque coatings, optical transmission-based imaging has been developed and applied in the Roll-to-Roll system using a flashlight and a high-sensitivity CCD camera. We observed high signal-to-noise ratio images while the Roll-to-Roll system ran at 5 ft/min. The entire sample image could quickly be recovered from the discrete frames using customized Python codes for automatic frame cropping and stitching. We detected significant non-uniformities in our experimental MEAs specimen. For fuel cell and low-temperature electrolysis (LTE) transparent membranes, we used optical reflectance hyperspectral imaging with interference fringe-based thickness mapping. We set up a hyperspectral camera to measure various rolls of commercial membranes. The measurement results are analyzed to find the thickness distribution of each roll and to check for defects. Transmission and reflection imaging-based quality monitoring techniques demonstrated in this project can be widely used in the mass production environment to improve the production yield and performance of hydrogen devices.

DIRECT ENERGY CONVERSION,ENGINEERING↗

Trimethoxymethane: A Fuel For Direct-Oxidation Fuel Cells

Trimethoxymethane (TMM) identified as high-energy fuel for direct-oxidation fuel cells. Synthesized from natural gas (methane) and handled easily because non-toxic, low-vapor-pressure liquid. Data obtained from both half-cell and full-cell tests indicate that TMM oxidized at very high rates. Considered excellent candidate for use in direct-oxidation fuel cells in vehicles and portable power supplies

Olah, George A.↗

National Fuel Cell Bus Program: Accelerated Testing Evaluation Report and Appendices, Alameda-Contra Costa Transit District (AC Transit)

This is an evaluation of hydrogen fuel cell transit buses operating at AC Transit in revenue service since March 20, 2006 compared to similar diesel buses operating from the same depot. This evaluation report includes results from November 2007 through October 2008. Evaluation results include implementation experience, fueling station operation, fuel cell bus operations at Golden Gate Transit, and evaluation results at AC Transit (bus usage, availability, fuel economy, maintenance costs, and roadcalls).

02 PETROLEUM↗

Application of Molecular Catalysts for the Oxygen Reduction Reaction in Alkaline Fuel Cells

Here, the development of precious group metal-free (PGM-free) catalysts for the oxygen reduction reaction is considered as the main thrust for the cost reduction of fuel cell technologies and their mass production. Within the PGM-free category, molecular catalysts offer an advantage over other heat-treated PGM-free catalysts owing to their well-defined structure, which enables further design of more active, selective, and durable catalysts. Even though non-heat-treated molecular catalysts with exceptional performance have been reported in the past, they were rarely tested in a fuel cell. Herein, we report on a molecular catalyst under alkaline conditions: fluorinated iron phthalocyanine (FeFPc) supported on cheap and commercially available high-surface area carbon-BP2000 (FeFPc@BP2000). It exhibits the highest activity ever reported for molecular catalysts under alkaline conditions in half-cells and fuel cells.

25 ENERGY STORAGE↗

Durable Fuel Cell MEA through Immobilization of Catalyst Particle and Membrane Chemical Stabilizer

For hydrogen-based fuel cell electric vehicle to be cost competitive with the incumbent diesel-powered internal combustion engine heavy-duty vehicle, the total cost of ownership of the truck must be decreased via both capital cost and the operating cost (H 2 fuel expense) reduction. This puts the emphasis on the decrease of fuel cell stack cost via use of low platinum catalyst material usage to decrease capital cost, high H 2 fuel efficiency and high stack durability to decrease the operating cost. US DOE has set a target of ≤ 0.25 mgPt/cm 2 total loading in the membrane electrode assembly, high fuel efficiency of > 68% and a HD-combined target of ≥ 2.5 kW/gPGM after running an accelerated stress test (AST) equivalent to 30,000 hours of heavy-duty fuel cell operation.

08 HYDROGEN↗

Performance of Anode-Supported Solid Oxide Fuel Cell with Thin Bi-Layer Electrolyte by Pulsed Laser Deposition

Anode-supported yttria stabilized zirconia (YSZ)/samaria doped ceria (SDC) bi-layer electrolytes with uniform thickness and high density were fabricated by pulsed laser deposition at 1000 degrees C. Fuel cells with such bi-layer electrolytes were fabricated and tested, yielding open circuit voltages from 0.94 to 1.0 V at 600-700 degrees C. Power densities from 0.4 to 1.0 W cm{sup -2} at 0.7 V were achieved in air at temperatures of 600-700 degrees C. Cell performance was improved in flowing oxygen, with an estimated peak power density of over 2 W cm{sup -2} at 650 degrees C, assuming the same overall resistance over the entire range of current density. The high cell performance was attributed to the very low ohmic resistance of the fuel cell, owing to the small thickness of the electrolyte. Stable performance was also demonstrated in that the voltage of the fuel cell showed very little change at a constant current density of 1 A cm{sup -2} during more than 400 hours of operation at 650 degrees C in flowing oxygen. SEM analysis of the fuel cell after testing showed that the bi-layer electrolyte had retained its chemical and mechanical integrity.

30 DIRECT ENERGY CONVERSION↗

Unraveling the core of fuel cell performance: engineering the ionomer/catalyst interface

The biggest obstacle to the widespread implementation of polymer electrolyte membrane fuel cells (PEMFCs) is their cost, primarily due to the use of platinum catalysts. The high intrinsic catalyst activity exhibited on a rotating disk electrode (RDE) is rarely realized in a membrane electrode assembly (MEA), which is a long-standing challenge for PEMFCs and a cause of low catalyst utilization. To translate the high RDE performance of a catalyst into a MEA, the design of an ideal ionomer/catalyst interface is proposed: a thin, conformal ionomer film covers the maximum surface of a Pt nanoparticle and thus simultaneously maximizes catalyst utilization, (i.e., high mass activity and electrochemically active surface area) and O 2 diffusion rate (i.e., high current density performance) without compromising proton conduction. Building such an interface is a long-standing challenge due to the lack of interaction between the ionomer and catalyst particles, resulting in large ionomer agglomerates and inhomogeneous ionomer coverage over the catalyst nanoparticle, with consequent poor fuel cell performance. In this work, this ionomer/catalyst interface has been engineered, utilizing the electrostatic attraction between positively charged catalyst and negatively charged ionomer particles in a catalyst ink and preserved in a solid catalyst layer. As a result, this interface leads to previously unachieved proton exchange membrane fuel cell performance in terms of both catalyst utilization (75% vs. 45%) and peak/rated power density (i.e., 1.430/0.930 W cm -2 , H 2 /air, cathode Pt loading: 0.1 mgPt cm -2 ) for pure Pt catalysts, even better than those of Pt alloy catalysts. This work demonstrates the formation of an interface in the liquid phase (using ultra-small-angle X-ray scattering in combination with cryo-TEM, isothermal–titration–calorimetry) and the preservation of the interface in the solid catalyst layer (using TEM) and estimates the effective coverage and thickness of the ionomer film (using limiting current density, RDE and fuel cell performance).

25 ENERGY STORAGE↗

Monolithic Solid Oxide Fuel Cell development

The Monolithic Solid Oxide Fuel Cell (MSOFC) is an oxide-ceramic structure in which appropriate electronic and ionic conductors are fabricated in a honeycomb shape similar to a block of corrugated paperboard. These electronic and ionic conductors are arranged to provide short conduction paths to minimize resistive losses. The power density achievable with the MSOFC is expected to be about 8 kW/kg or 4 kW/L, at fuel efficienceis over 50 percent, because of small cell size and low resistive losses in the materials. The MSOFC operates in the range of 700 to 1000 C, at which temperatures rapid reform of hydrocarbon fuels is expected within the nickel-YSZ fuel channels. Tape casting and hot roll calendering are used to fabricate the MSOFC structure. The performance of the MSOFC has improved significantly during the course of development. The limitation of this system, based on materials resistance alone without interfacial resistances, is 0.093 ohm-sq cm area-specific resistance (ASR). The current typical performance of MSOFC single cells is characterized by ASRs of about 0.4 to 0.5 ohm-sq cm. With further development the ASR is expected to be reduced below 0.2 ohm-sq cm, which will result in power levels greater than 1.4 W/sq cm. The feasibility of the MSOFC concept was proven, and the performance was dramatically improved. The differences in thermal expansion coefficients and firing shrinkages among the fuel cell materials were minimized. As a result of good matching of these properties, the MSOFC structure was successfully fabricated with few defects, and the system shows excellent promise for development into a practical power source.

Myles, K. M.↗

Analyzing the Potential for Stationary Fuel Cells to Augment Hydrogen Availability in the Transition to Hydrogen Vehicles

The lack of refueling stations is one of the biggest barriers to the transition to hydrogen-powered transportation. Stationary fuel cells, when deployed and operated to co-generate heat, hydrogen and power, could serve as distributed sources of hydrogen for motor vehicles. This study uses a hydrogen transition market simulation model to analyze the potential for stationary fuel cells to augment hydrogen availability during the early stage of a hydrogen transition. The analysis contributes to understanding potential synergies between stationary and mobile hydrogen fuel cell applications.

08 HYDROGEN↗