Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Finite Elements”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

A least-squares finite element method for 3D incompressible Navier-Stokes equations

The least-squares finite element method (LSFEM) based on the velocity-pressure-vorticity formulation is applied to three-dimensional steady incompressible Navier-Stokes problems. This method can accommodate equal-order interpolations, and results in symmetric, positive definite algebraic system. An additional compatibility equation, i.e., the divergence of vorticity vector should be zero, is included to make the first-order system elliptic. The Newton's method is employed to linearize the partial differential equations, the LSFEM is used to obtain discretized equations, and the system of algebraic equations is solved using the Jacobi preconditioned conjugate gradient method which avoids formation of either element or global matrices (matrix-free) to achieve high efficiency. The flow in a half of 3D cubic cavity is calculated at Re = 100, 400, and 1,000 with 50 x 52 x 25 trilinear elements. The Taylor-Gortler-like vortices are observed at Re = 1,000.

Jiang, Bo-Nan↗
NASA NTRS1994

Issues concerning the updating of finite-element models from experimental data

Some issues concerning the updating of dynamic finite-element models by incorporation of experimental data are examined here. It is demonstrated how the number of unknowns can be greatly reduced if the physical nature of the model is maintained. The issue of uniqueness is also examined and it is shown that a number of previous workers have been mistaken in their attempts to define both sufficient and necessary measurement requirements for the updating problem to be solved uniquely. The relative merits of modal and frequency response function (frf) data are discussed and it is shown that for measurements at fewer degrees of freedom than are present in the model, frf data will be unlikely to converge easily to a solution. It is then examined how such problems may become more tractable by using new experimental techniques which would allow measurements at all degrees of freedom present in the mathematical model.

Dunn, Shane A.↗
NASA NTRS1978

CELFE: Coupled Eulerian-Lagrangian Finite Element program for high velocity impact. Part 1: Theory and formulation

A 3-D finite element program capable of simulating the dynamic behavior in the vicinity of the impact point, together with predicting the dynamic response in the remaining part of the structural component subjected to high velocity impact is discussed. The finite algorithm is formulated in a general moving coordinate system. In the vicinity of the impact point contained by a moving failure front, the relative velocity of the coordinate system will approach the material particle velocity. The dynamic behavior inside the region is described by Eulerian formulation based on a hydroelasto-viscoplastic model. The failure front which can be regarded as the boundary of the impact zone is described by a transition layer. The layer changes the representation from the Eulerian mode to the Lagrangian mode outside the failure front by varying the relative velocity of the coordinate system to zero. The dynamic response in the remaining part of the structure described by the Lagrangian formulation is treated using advanced structural analysis. An interfacing algorithm for coupling CELFE with NASTRAN is constructed to provide computational capabilities for large structures.

Lee, C. H.↗
NASA NTRS2010

Modification of a Macromechanical Finite-Element Based Model for Impact Analysis of Triaxially-Braided Composites

A macro level finite element-based model has been developed to simulate the mechanical and impact response of triaxially-braided polymer matrix composites. In the analytical model, the triaxial braid architecture is simulated by using four parallel shell elements, each of which is modeled as a laminated composite. For the current analytical approach, each shell element is considered to be a smeared homogeneous material. The commercial transient dynamic finite element code LS-DYNA is used to conduct the simulations, and a continuum damage mechanics model internal to LS-DYNA is used as the material constitutive model. The constitutive model requires stiffness and strength properties of an equivalent unidirectional composite. Simplified micromechanics methods are used to determine the equivalent stiffness properties, and results from coupon level tests on the braided composite are utilized to back out the required strength properties. Simulations of quasi-static coupon tests of several representative braided composites are conducted to demonstrate the correlation of the model. Impact simulations of a represented braided composites are conducted to demonstrate the capability of the model to predict the penetration velocity and damage patterns obtained experimentally.

Goldberg, Robert K.↗
NASA NTRS2023

Finite Element Simulation of Three Full-Scale Crash Tests for Cessna 172 Aircraft

The NASA Emergency Locator Transmitter Survivability and Reliability project was initiated in 2013 to assess the crash performance standards for the next generation of emergency locator transmitter (ELT) systems. Three Cessna 172 aircraft were acquired to perform crash testing at the NASA Langley Research Center Landing and Impact Research Facility. Full-scale crash tests were conducted in the summer of 2015, and each test article was subjected to severe, but survivable, impact conditions including a flare-to-stall during emergency landing and two controlled-flight-into-terrain scenarios. Finite element analyses were performed to numerically simulate the aircraft response to the crash tests. The first test simulated impacting a concrete surface represented analytically by a rigid plane. Tests 2 and 3 simulated impacting a dirt surface represented analytically by an Eulerian grid of brick elements using a Mohr–Coulomb material model. The objective of this paper is to summarize the test and analysis results for the three full-scale crash tests. Simulation models of the airframe that correlate well with the tests are needed for future studies of alternate ELT mounting configurations.

Finite Element Analysis↗
NASA NTRS2023

Finite Element Simulation of Three Full-Scale Crash Tests for Cessna 172 Aircraft

The NASA Emergency Locator Transmitter Survivability and Reliability project was initiated in 2013 to assess the crash performance standards for the next generation of emergency locator transmitter (ELT) systems. Three Cessna 172 aircraft were acquired to perform crash testing at the NASA Langley Research Center Landing and Impact Research Facility. Full-scale crash tests were conducted in the summer of 2015 and each test article was subjected to severe, but survivable, impact conditions including a flare-to-stall during emergency landing, and two controlled-flight-into-terrain scenarios. Finite element analyses were performed to numerically simulate the aircraft response to the crash tests. The first test simulated impacting a concrete surface represented analytically by a rigid plane. Tests 2 and 3 simulated impacting a dirt surface represented analytically by an Eulerian grid of bric k elements using a Mohr-Coulomb material model. The objective of this paper is to summarize the test and analysis results for the three full-scale crash tests. Simulation models of the airframe which correlate well with the tests are needed for future studies of alternate ELT mounting configurations.

Finite Element Analysis↗
NASA NTRS2009

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems, Phase II: Material Model Development and Simulation of Experiments - Part 3

A team consisting of Arizona State University, Honeywell Engines, Systems & Services, the National Aeronautics and Space Administration Glenn Research Center, and SRI International collaborated to develop computational models and verification testing for designing and evaluating turbine engine fan blade fabric containment structures. This research was conducted under the Federal Aviation Administration Airworthiness Assurance Center of Excellence and was sponsored by the Aircraft Catastrophic Failure Prevention Program. The research was directed toward improving the modeling of a turbine engine fabric containment structure for an engine blade-out containment demonstration test required for certification of aircraft engines. The research conducted in Phase II began a new level of capability to design and develop fan blade containment systems for turbine engines. Significant progress was made in three areas: (1) further development of the ballistic fabric model to increase confidence and robustness in the material models for the Kevlar(TradeName) and Zylon(TradeName) material models developed in Phase I, (2) the capability was improved for finite element modeling of multiple layers of fabric using multiple layers of shell elements, and (3) large-scale simulations were performed. This report concentrates on the material model development and simulations of the impact tests.

Zylon↗
NASA NTRS1971

Finite elements for determination of crack tip elastic stress intensity factors.

A new type of finite element is introduced which embodies the inverse square root singularity of the stress distribution arising near a crack in an elastic medium. Using this element near the crack tip in two typical cracked configurations, stress intensity factors within 5% of accepted values were obtained, with meshes having as few as 250 degrees of freedom.

Tracey, D. M.↗
NASA NTRS1977

Transmission in nonuniform ducts - A comparative evaluation of finite element and weighted residuals computational schemes

The Method of Weighted Residuals (MWR) and the Finite Element Method (FEM) are considered as computational schemes in the problem of acoustic transmission in nonuniform ducts. MWR is presented in an improved form which includes the interaction of acoustic modes (irrotational) and hydrodynamic modes (rotational). FEM is based on a weighted residuals formulation using eight noded isoparametric elements. Both are applicable to two-dimensional and axially symmetric problems. Calculations are made for several sample problems to demonstrate accuracy and relative efficiency. One test case has implications in the phenomenon of subsonic acoustic choking and it is found that a large transmission loss is not an automatic consequence of propagation against a high subsonic mean flow.

Eversman, W.↗
NASA NTRS1978

On the accuracy and convergence of implicit numerical integration of finite element generated ordinary differential equations

A study of accuracy and convergence of linear functional finite element solution to linear parabolic and hyperbolic partial differential equations is presented. A variable-implicit integration procedure is employed for the resultant system of ordinary differential equations. Accuracy and convergence is compared for the consistent and two lumped assembly procedures for the identified initial-value matrix structure. Truncation error estimation is accomplished using Richardson extrapolation.

Baker, A. J.↗
NASA NTRS1982

Approximating a finite element model of a hybrid deployable truss by a discrete mass model

The NASTRAN finite element model of the MSFC/hybrid deployable truss is approximated by a model consisting of four bodies serially connected by a spring hinge suspension. The truss is decomposed into four serially connected modules determining the total mass and rotational inertias for a rigid body with its mass center on the axis of the truss for each module. A five-body cantilever truss model is developed along with an undamped form of this model. Spring coefficient values are generated to match eigenvalues of the latter model with those of the NASTRAN model. Damping coefficients are then determined that provide n percent of critical damping for the model.

Chichester, F. D.↗
NASA NTRS1986

Finite element modelling of non-linear magnetic circuits using Cosmic NASTRAN

The general purpose Finite Element Program COSMIC NASTRAN currently has the ability to model magnetic circuits with constant permeablilities. An approach was developed which, through small modifications to the program, allows modelling of non-linear magnetic devices including soft magnetic materials, permanent magnets and coils. Use of the NASTRAN code resulted in output which can be used for subsequent mechanical analysis using a variation of the same computer model. Test problems were found to produce theoretically verifiable results.

Sheerer, T. J.↗
NASA NTRS1985

Structural parameter identification of distributed systems using finite element approximation

A system identification technique is developed for classes of distributed systems using finite element approximations. Vibrating systems represented by partial differential equations have physical parameters associated with mass, stiffness, and damping distributions which need to be known in order to properly control and design mathematical models of the system. In order to identify these parameters a weighted least-squares algorithm and modified Newton-Raphson method is used for the identification process. The theory and technique is demonstrated by estimating the system parameters of a vibrating cantilever beam made up of several different structural properties.

Lee, K. Y.↗