Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Fans”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Compressor and fan wake characteristics

Approaches for developing an analytical model capable of determining the effects of rotor flow and blade parameters and turbulence properties (i.e. energy, velocity correlations, and length scale) on the rotor wake characteristics and its diffusion properties are discussed. The three-dimensional model will employ experimental measurements, instantaneous velocities, and turbulence properties at various stations downstream from a rotor. A triaxial probe and a rotating conventional probe, which is mounted on a traverse gear operated by two step motors, are to be used for these measurements. The final rotor wake model will be capable of predicting the discrete and broadband noise generated in a fan rotor and of evaluating the aerodynamic losses, efficiency and optimum spacing between a rotor and stator in turbomachinery.

Lakshminarayana, B.↗
NASA NTRS1975

An experimental study of the effect of treated length on fan inlet noise suppressors

An experimental study of the effect of length of acoustic treatment was performed on a full scale fan using two different inlets. Analysis of the data revealed that measured suppression varied linearly with the length of the ringed linear segments as anticipated. Further analysis indicated that the wall only portion of the treatment was substantially more effective than anticipated suggesting that, if only moderate suppression is needed, wall only treatment may suffice. Contrary to expectation the two inlets behaved similarly. Introduction of a hard exhaust splitter into the configuration resulted in a noise increase at certain frequencies.

Dittmar, J. H.↗
NASA NTRS1975

Effects of long-chord acoustically treated stator vanes on fan noise. 1: Effect of long chord (taped stator)

A set of long-chord stator vanes was designed to replace the vanes in an existing fan stage. The long vanes consisted of a turning section and axial extension pieces, both of which incorporated acoustic damping material. The acoustic damping material was made inactive for these tests by covering with metal tape, and the stator vanes were tested in three length configurations. Compared to the values for the original stage, broadband noise was reduced in the middle to high frequencies with the long stator vanes, but a broadband noise increase was observed at the low frequencies. No change was observed in the blade passage tone, but some aft end reduction in the overtones was observed.

Dittmar, J. H.↗
NASA NTRS1975

Redesigned rotor for a highly loaded, 1800 ft/sec tip speed compressor fan stage 1: Aerodynamic and mechanical design

A highly loaded, high tip-speed fan rotor was designed with multiple-circular-arc airfoil sections as a replacement for a marginally successful rotor which had precompression airfoil sections. The substitution of airfoil sections was the only aerodynamic change. Structural design of the redesigned rotor blade was guided by successful experience with the original blade. Calculated stress levels and stability parameters for the redesigned rotor are within limits demonstrated in tests of the original rotor.

Halle, J. E.↗
NASA NTRS1975

Reduction of Noise from a Fan Stage for a Turbofan Engine by Use of Long-Chord Acoustically-Treated Stator Vanes

A set of acoustically-treated long-chord vanes was designed to replace the vanes in an existing fan stage to investigate the noise reduction possibilities of both increased stator chord length and a method of incorporating acoustic damping material. The vanes were tested with both active and inactive acoustic surfaces. Results of the inactive tests show significant broadband noise effects with noise reductions in the middle to high frequencies and an increase at low frequencies. No reduction in blade passage tone was observed, but decreases in the overtones were observed. Results of the tests with the active acoustic treatment show large noise reductions over a wide frequency range.

Dittmar, J. H.↗
NASA NTRS1976

Effects of four inlet and outlet tip-annulus-area blockage configurations on the performance of an axial-flow fan rotor

An axial-flow fan rotor was tested with four configurations of tip-annulus-area blockage to speeds as high as 0.8 of design speed. The rotor performance with the four blockage configurations is compared with the unblocked rotor performance and with blockage configurations previously investigated. The blockage configurations enable the rotor to operate in a stable condition, to much lower flows than the unblocked rotor, with no evidence of rotating stall. The blockage configurations were effective in reducing rotor torque and weight flow but were accompanied by reductions in pressure ratio and efficiency.

Osborn, W. M.↗
NASA NTRS1976

Performance of a low-pressure fan stage with reverse flow

The reverse flow aerodynamic performance of a 51-centimeter-diameter fan stage is presented. The stage was tested with the variable pitch rotor blades set through feather at -75 deg, -80 deg, and -85 deg from design setting angle. Of the three tested the stage with the rotor blades set at -75 deg exhibited the highest pressure ratio and highest flow. For all three configurations, there was little or no flow in the inner third of the exit passage due to the rotor blade being almost perpendicular to the axial direction in the hub region.

Moore, R. D.↗
NASA NTRS1976

Performance of low-pressure-ratio low-tip-speed fan stage with blade tip solidity of 0.65

The overall and blade-element performance of a low pressure ratio, low tip speed fan stage is presented over the stable operating range at rotative speeds from 90 to 120 percent of design speed. Stage peak efficiency of 0.927 was obtained at a weight flow of 32.4 kg/sec (190.31 kg/sec/sq m of annulus area) and a pressure ratio of 1.134. The stall margin at design speed and peak efficiency was 15.3 percent.

Kovich, G.↗
NASA NTRS1976

Additional design studies of the NASA/Navy lift/cruise fan

Additional preliminary design studies were performed for a turbotip lift/cruise fan propulsion system for a Navy multimission aircraft. The LCF459/J97 propulsion system was previously designed for this application. These studies extended the analysis in areas of (1) scroll commonality, (2) increased engine-out contingency ratings, (3) mounting systems, (4) manufacturing cost reductions, and (5) vulnerability.

Source record↗
NASA NTRS1976

Overall and blade element performance of a 1.20 pressure ratio fan stage with rotor blades reset -7 deg

A 51-cm-diam model of a fan stage for short haul aircraft was tested in a single stage compressor research facility. The rotor blades were set 7 deg toward the axial direction (opened) from the design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed and a weight flow of 30.9 kg/sec, the stage pressure ratio and efficiency were 1.205 and 0.85, respectively. The design speed rotor peak efficiency of 0.90 occurred at a flow rate of 32.5 kg/sec.

Lewis, G. W., Jr.↗
NASA NTRS1976

Overall and blade element performance of a 1.20-pressure-ratio fan stage with rotor blades reset -5 deg

A 51-cm-diam model of a fan stage for a short haul aircraft was tested in a single stage-compressor research facility. The rotor blades were set 5 deg toward the axial direction (opened) from design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed of 213.3 m/sec and a weight flow of 31.5 kg/sec, the stage pressure ratio and efficiency were 1.195 and 0.88, respectively. The design speed rotor peak efficiency of 0.91 occurred at the same flow rate.

Lewis, G. W., Jr.↗
NASA NTRS1975

Design definition study of a life/cruise fan technology V/STOL aircraft. Volume 2, addendum 2: Program risk assessment

The results are presented of a risk assessment study conducted on two technology aircraft. The aircraft system components were reviewed and assessed for risk based on: (1) complexity relative to state-of-the-art, (2) manufacturing and qualification testing, (3) availability and delays, and (4) cost/schedule impact. These assessments were based on five risk nomenclatures: low, minor, moderate, high, and extreme. Each aircraft system was assigned an overall risk rating depending upon its contribution to the capability of the aircraft to achieve the performance goals. The slightly lower Sabreliner performance margin is due to the restricted flight envelope, the fixed landing gear, and internal fuel capacity. The Sabreliner with retractable gear and allowed to fly at its best speed and altitude would reflect performance margins similar to the New Airframe. These significant margins, inherent with the MCAIR three gas generator/three fan propulsion system, are major modifiers to risk assessment of both aircraft. The estimated risk and the associated key system and performance areas are tabulated.

Source record↗
NASA NTRS1976

Performance of a 1.57 pressure-ratio transonic fan stage with a screen-induced 90 deg circumferential inlet flow distortion

A transonic fan stage having a design pressure ratio of 1.57 was tested with a 90 degree circumferential distortion imposed on the inlet flow. The rotor diameter was approximately 50.8 cm, and the design pressure ratio was 1.60 at a tip speed of 425 m/sec. Overall performance at 70 and 100 percent of design speed showed a loss of stall pressure ratio and flow range at design speed and no significant loss in stall pressure ratio at 70 percent of design speed. Detailed flow measurements are presented to show the rotor-upstream flow interactions and the attenuation and amplification properties through the stage.

Sanger, N. L.↗
NASA NTRS1976

Experimental and theoretical studies of subsonic fan noise

The noise generated by inlet turbulence impinging on a subsonic axial flow fan was studied as a function of tip speed, flow coefficient, and intensity and scale of turbulence was carried out. Both turbulence and far field acoustic measurements were made. The new elements introduced in the theoretical analysis were accounting for blade loading dependent noise mechanisms and consideration of anisotropic turbulence impinging on the rotor because of inlet flow contraction effects. Experimentally an unexplained increase of noise at about 1/2 and 1 1/2 times blade passsing frequency was observed at low flow coefficients even though there was no evidence of compressor surge. In the final version the theory does a fair job of predicting variations of noise with blade loading and tip speed. Alteration of inlet turbulence length scales produced some but not very pronounced changes in the far field PWL spectra. Some degree of eddy contraction and resulting anisotropy were essential to explain the concentration of energy around blade passing frequencies.

Mani, R.↗
NASA NTRS1976

Noise reduction from the redesign of a fan stage to minimize stator lift fluctuations

An existing fan stage, redesigned to reduce stator lift fluctuations, was acoustically tested for reduced noise generation. The lift fluctuations on the stator were reduced by increasing the stator chord, adjusting incidence angles, and by adjusting the rotor velocity diagrams. The experiments showed significantly reduced broadband noise levels in the middle to high frequencies. Blade passage tone power was not reduced, but decreases in the harmonics were observed. Aerodynamic improvements in both performance and efficiency were obtained.

Dittmar, J. H.↗
NASA NTRS1976

Filament-wound spar shell graphite/epoxy fan blades

The methodology for fabrication of wet filament wound spar shell fan blades is presented. All principal structural elements were filament wound, assembled, formed, bonded and co-cured in a female mold. A pair of blades were fabricated as one integral unit and parted into two after curing.

Yao, S.↗
NASA NTRS1976

Vibration characteristics of composite fan blades and comparison with measured data

The vibration characteristics of a composite fan blade for high-tip-speed applications were determined theoretically and the results compared with measured data. The theoretical results were obtained using a computerized capability consisting of NASTRAN coupled with composite mechanics by way of pre- and postprocessors. The predicted vibration frequencies and mode shapes were in reasonable agreement with the measured data. Theoretical results showed that different laminate configurations from the same composite system had only small effects on the blade frequency. However, the use of adhesively bonded titanium/beryllium laminar composites may improve considerably the blade vibration characteristics.

Chamis, C. C.↗