Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electron diffraction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Physical properties of epitaxial ZrN/MgO(001) layers grown by reactive magnetron sputtering

Single-crystal ZrN films, 830 nm thick, are grown on MgO(001) at 450 °C by magnetically unbalanced reactive magnetron sputtering. The combination of high-resolution x-ray diffraction reciprocal lattice maps, high-resolution cross-sectional transmission electron microscopy, and selected-area electron diffraction shows that ZrN grows epitaxially on MgO(001) with a cube-on-cube orientational relationship, (001){sub ZrN}‖(001){sub MgO} and [100]{sub ZrN}‖[100]{sub MgO}. The layers are essentially fully relaxed with a lattice parameter of 0.4575 nm, in good agreement with reported results for bulk ZrN crystals. X-ray reflectivity results reveal that the films are completely dense with smooth surfaces (roughness = 1.3 nm, consistent with atomic-force microscopy analyses). Based on temperature-dependent electronic transport measurements, epitaxial ZrN/MgO(001) layers have a room-temperature resistivity ρ{sub 300K} of 12.0 μΩ-cm, a temperature coefficient of resistivity between 100 and 300 K of 5.6 × 10{sup −8}Ω-cm K{sup −1}, a residual resistivity ρ{sub o} below 30 K of 0.78 μΩ-cm (corresponding to a residual resistivity ratio ρ{sub 300Κ}/ρ{sub 15K} = 15), and the layers exhibit a superconducting transition temperature of 10.4 K. The relatively high residual resistivity ratio, combined with long in-plane and out-of-plane x-ray coherence lengths, ξ{sub ‖} = 18 nm and ξ{sub ⊥} = 161 nm, indicates high crystalline quality with low mosaicity. The reflectance of ZrN(001), as determined by variable-angle spectroscopic ellipsometry, decreases slowly from 95% at 1 eV to 90% at 2 eV with a reflectance edge at 3.04 eV. Interband transitions dominate the dielectric response above 2 eV. The ZrN(001) nanoindentation hardness and modulus are 22.7 ± 1.7 and 450 ± 25 GPa.

36 MATERIALS SCIENCE↗

Growth modes in metal-organic molecular beam epitaxy of TiO{sub 2} on r-plane sapphire

Phase pure, epitaxial (101) rutile TiO{sub 2} films were grown on (012) sapphire substrates at temperatures between 485 and 725 deg. C using metal-organic molecular beam epitaxy with titanium tetraisopropoxide as the Ti source. Growth modes and rates were investigated as a function of substrate temperature using reflection high-energy electron diffraction, x-ray reflectivity, atomic force microscopy, and transmission electron microscopy. Growth rates were as high as 125 nm/h. The influence of additional oxygen supplied from a rf plasma source was investigated. Without oxygen plasma, the growth rate exhibited reaction and flux-limited regimes and layer-by-layer growth was observed in the initial stages of film growth. With oxygen plasma the growth rate became independent of temperature; films grew initially in step-flow mode and were insulating. The mechanisms for the different growth modes as a function of film thickness, temperature, and presence of oxygen are discussed.

36 MATERIALS SCIENCE↗

Synthesis, structural and optical properties of BaMoO{sub 4}:Eu{sup 3+} shuttle like phosphors

Graphical abstract: - Highlights: • BaMoO{sub 4}:Eu{sup 3+} phosphors were synthesized by a facile synthesis route. • PL and CL spectra showed dominant emissions due to ({sup 5}D{sub 0} → {sup 7}F{sub 2}) hypersensitive transitions. • The excitation wavelengths in the UV-B region make BaMoO{sub 4}:Eu{sup 3+} phosphors as a good candidate in the red region for the development of UV-based white LEDs. • PL and CL spectra showed similar CIE values close to the commercially available Y{sub 2}O{sub 3}:Eu{sup 3+} phosphors. - Abstract: Eu{sup 3+} ions doped BaMoO{sub 4} phosphor samples were synthesized by a facile synthesis process. The tetragonal phase of the host lattice was substantiated by the X-ray diffraction patterns. The morphological studies were carried out by taking the scanning electron microscope and transmission electron microscope images and confirmed the formation of shuttle like particles with perpendicular protrusions in the middle of the particle. The single crystalline nature of the phosphors was confirmed by the selected area electron diffraction pattern. The photoluminescence (PL) properties of the Eu{sup 3+} ions doped samples revealed good emission with a high asymmetry ratio when excited with ultraviolet B wavelengths (between 280 and 315 nm). The cathodoluminescence (CL) spectra showed similar results to the PL spectra. The calculated CIE values based on the PL and CL spectra were almost similar and confirmed the rich red emission.

36 MATERIALS SCIENCE↗

Role of Dysprosium Doping on Structural, Optical, Magnetic and Electrical Properties of ZnO Nanorods

Well-defined Dy-doped ZnO rods were synthesized by hydrothermal route. Various studies were carried out on the synthesized rods like x-ray diffraction to confirm their hexagonal wurtzite structure; TEM, HRTEM and selected area electron diffraction to establish their rodlike structure; energy-dispersive x-ray spectroscopy analysis confirming appropriate substitution of dopant; UV-Vis spectra, which showed decrease in band gap with dopant concentration and photoluminescence study furnishing information regarding the presence of various types of defects. Further, magnetic studies were done using VSM to confirm roomtemperature ferromagnetic behaviour of both for undoped and doped ZnO rods and, the electrical studies were performed using four probe method, which confirmed that the ‘variation in resistivity with dopant concentration’ was related to crystallinity of the samples. UV-Vis spectra showed effect of dopant concentration on band gap and photoluminescence study confirms induced ferromagnetic behaviour due to Dy doping.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Reordering between tetrahedral and octahedral sites in ultrathin magnetite films grown on MgO(001)

Magnetite ultrathin films were grown using different deposition rates and substrate temperatures. The structure of these films was studied using (grazing incidence) x-ray diffraction, while their surface structure was characterized by low energy electron diffraction. In addition to that, we performed x-ray photoelectron spectroscopy and magneto optic Kerr effect measurements to probe the stoichiometry of the films as well as their magnetic properties. The diffraction peaks of the inverse spinel structure, which originate exclusively from Fe ions on tetrahedral sites are strongly affected by the preparation conditions, while the octahedral sites remain almost unchanged. With both decreasing deposition rate as well as decreasing substrate temperature, the integrated intensity of the diffraction peaks originating exclusively from Fe on tetrahedral sites is decreasing. We propose that the ions usually occupying tetrahedral sites in magnetite are relocated to octahedral vacancies. Ferrimagnetic behaviour is only observed for well ordered magnetite films.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Ordered structures based on self-organized Au and CdSe nanoparticles

Methods for obtaining cadmium selenide and gold nanoparticles have been developed. The sizes of the nanoparticles are determined and the morphology, structure, and chemical composition of these nanoparticles and their ensembles are studied by a complex of structural methods: electron diffraction, X-ray diffraction, energy-dispersive X-ray analysis, high-resolution transmission electron microscopy, and small-angle X-ray scattering. Gold nanoparticles are mainly spherical and have an average size of 10 nm. They are single-phase and have an fcc crystal structure. Samples of synthesized CdSe nanoparticles contain monodisperse spherical particles 12 nm in size with a wurtzite structure. The deposition of nanoparticles on a carbon substrate is accompanied by their self-organization into a closely packed two-dimensional structure with a pronounced texture in which all nanoparticles are oriented in the [001] direction perpendicularly to the carbon substrate plane.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Capturing Structural Dynamics in Crystalline Silicon Using Chirped Electrons from a Laser Wakefield Accelerator

Recent progress in laser wakefield acceleration has led to the emergence of a new generation of electron and X-ray sources that may have enormous benefits for ultrafast science. These novel sources promise to become indispensable tools for the investigation of structural dynamics on the femtosecond time scale, with spatial resolution on the atomic scale. Here in this paper, we demonstrate the use of laser-wakefield-accelerated electron bunches for time-resolved electron diffraction measurements of the structural dynamics of single-crystal silicon nano-membranes pumped by an ultrafast laser pulse. In our proof-of-concept study, we resolve the silicon lattice dynamics on a picosecond time scale by deflecting the momentum-time correlated electrons in the diffraction peaks with a static magnetic field to obtain the time-dependent diffraction efficiency. Further improvements may lead to femtosecond temporal resolution, with negligible pump-probe jitter being possible with future laser-wakefield-accelerator ultrafast-electron-diffraction schemes.

36 MATERIALS SCIENCE↗

Twist-Angle-Dependent Ultrafast Charge Transfer in MoS 2 -Graphene van der Waals Heterostructures

Vertically stacked transition metal dichalcogenide-graphene heterostructures provide a platform for novel optoelectronic applications with high photoresponse speeds. Photoinduced nonequilibrium carrier and lattice dynamics in such heterostructures underlie these applications but have not been understood. In particular, the dependence of these photoresponses on the twist angle, a key tuning parameter, remains elusive. Here, using ultrafast electron diffraction, we report the simultaneous visualization of charge transfer and electron–phonon coupling in MoS 2 -graphene heterostructures with different stacking configurations. We find that the charge transfer timescale from MoS 2 to graphene varies strongly with twist angle, becoming faster for smaller twist angles, and show that the relaxation timescale is significantly shorter in a heterostructure as compared to a monolayer. These findings illustrate that twist angle constitutes an additional tuning knob for interlayer charge transfer in heterobilayers and deepen our understanding of fundamental photophysical processes in heterostructures, of importance for future applications in optoelectronics and light harvesting.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Epitaxial Fe-Ge thin films on Ge(111): Morphology, structure, and magnetic properties versus stoichiometry

We have studied the growth and magnetic properties of thin Fe-Ge films synthesized (codeposited at room temperature and postannealed at 250 deg. C) on Ge(111) wafers versus stoichiometry. Morphology and crystal structure have been investigated in situ by means of scanning tunneling microscopy, low-energy electron diffraction, and x-ray photoelectron diffraction and ex situ with x-ray diffraction. The magnetic properties were characterized ex situ by conventional polar and longitudinal magneto-optical Kerr effect and transverse biased initial inverse susceptibility and torque measurements. It is found that the growth is epitaxial for Ge content up to approx48 at. % (approxFe{sub 1.1}Ge composition). In particular, the film is homogeneous and flat and adopts a crystalline structure of hexagonal symmetry derived from the B8{sub 2} (Ni{sub 2}In) structure over a wide stoichiometry range extending from Fe{sub 2}Ge to Fe{sub 1.1}Ge. The epitaxial orientation between the Ge substrate and the germanide layer is (0001)Fe-Ge||(111)Ge with [1120]Fe-Ge||110]Ge. We found however that the surface periodicity and the out-of-plane lattice parameter c evolve within this stoichiometry range and two distinct stoichiometry regimes appear on both sides of a critical stoichiometry (approxFe{sub 1.5}Ge). Indeed, from Fe{sub 2}Ge to Fe{sub 1.5}Ge the surface periodicity is p(2x2) and c continuously decreases with Fe content, whereas from Fe{sub 1.5}Ge to Fe{sub 1.1}Ge the surface periodicity is (sq root(3)xsq root(3))R30 deg. and c remains constant. These features have been interpreted as a clear fingerprint of a minor transformation of the crystalline structure but without any change in symmetry. This structural order transformation is discussed in relation to previous results reported in the case of macroscopic single-crystal Fe-Ge ingots. On both sides of the wide [Fe{sub 2}Ge,Fe{sub 1.1}Ge] composition range the layer is no more homogeneous. More precisely, for higher Fe content the film contains both the above mentioned Ni{sub 2}In-derived phase and a Fe-richer phase (probably bcc Fe) whereas for higher Ge content the layer is amorphous. Magnetic characterization showed in particular that the homogeneous Ni{sub 2}In-derived epilayers are ferromagnetic with a Curie temperature that varies drastically with the stoichiometry, rising up to a high T{sub C} value of approx450 K for the Fe-rich Fe{sub 1.9}Ge composition. Finally, whatever the stoichiometry, the magnetic easy axis of the homogeneous phase lies in the film plane and a small uniaxial anisotropy is superimposed on a sixfold order one that results from the hexagonal symmetry of the crystallographic structure.

36 MATERIALS SCIENCE↗

Metal thin film growth on multimetallic surfaces: From quaternary metallic glass to binary crystal

The work presented in this thesis mainly focuses on the nucleation and growth of metal thin films on multimetallic surfaces. First, we have investigated the Ag film growth on a bulk metallic glass surface. Next, we have examined the coarsening and decay of bilayer Ag islands on NiAl(110) surface. Third, we have investigated the Ag film growth on NiAl(110) surface using low-energy electron diffraction (LEED). At last, we have reported our investigation on the epitaxial growth of Ni on NiAl(110) surface. Some general conclusions can be drawn as follows. First, Ag, a bulk-crystalline material, initially forms a disordered wetting layer up to 4-5 monolayers on Zr-Ni-Cu-Al metallic glass. Above this coverage, crystalline 3D clusters grow, in parallel with the flatter regions. The cluster density increases with decreasing temperature, indicating that the conditions of island nucleation are far-from-equilibrium. Within a simple model where clusters nucleate whenever two mobile Ag adatoms meet, the temperature-dependence of cluster density yields a (reasonable) upper limit for the value of the Ag diffusion barrier on top of the Ag wetting layer of 0.32 eV. Overall, this prototypical study suggests that it is possible to grow films of a bulk-crystalline metal that adopt the amorphous character of a glassy metal substrate, if film thickness is sufficiently low. Next, the first study of coarsening and decay of bilayer islands has been presented. The system was Ag on NiAl(110) in the temperature range from 185 K to 250 K. The coarsening behavior, has some similarities to that seen in the Ag(110) homoepitaxial system studied by Morgenstern and co-workers. At 185 K and 205 K, coarsening of Ag islands follows a Smoluchowski ripening pathway. At 205 K and 250 K, the terrace diffusion limited Ostwald ripening dominants. The experimental observed temperature for the transition from SR to OR is 205 K. The SR exhibits anisotropic island diffusion and the OR exhibits 1D decay of island length while keeping the corresponding island width constant. Third, LEED indicates that, up to about 6 BL (12 ML), the Ag film adopts the (110) structure on lattice matched NiAl(110) surface, supporting the previous assignment based upon island heights measured in STM. Starting at 4.5 to 6 BL, (111) diffraction pattern is detected. This is also in agreement with previous STM study. Careful examinations of the LEED patterns reveal the slight difference in lattice constants between bulk Ag and bulk NiAl. At last, we performed STM studies of Ni deposition on NiAl(110) in the temperature range from 200 K to 400 K. Ni forms 'dense' Ni(100)-like islands on NiAl(110) with a zig-zag shaped stripe feature which is probably due to strain relief. DFT analysis provides insights into the island growth shapes, which are rationalized by the thermodynamics and kinetics of the film growth process. For thick Ni films (coverage exceeding 6 ML), a Ni(111)-like structure developed. Traditional MF theory is applied to analyze island density at 200 K. Deviation from homogeneous nucleation behavior for island size distribution and island density reveals the presence of heterogeneous nucleation mediated by the Ni antisite point defects on NiAl(110) surface.

36 MATERIALS SCIENCE↗

Metastable fcc-Fe film epitaxially grown on Cu(100) single-crystal underlayer

Fe film of 40 nm thickness is prepared on fcc-Cu(100) single-crystal underlayer at room temperature by ultra-high vacuum molecular beam epitaxy. The film growth and the detailed structure are investigated by reflection high-energy electron diffraction, cross-sectional high-resolution transmission electron microscopy (HR-TEM), and x-ray diffraction (XRD). An Fe single-crystal with metastable fcc structure nucleates on the underlayer. The HR-TEM shows that fcc lattice is formed from the Fe/Cu interface up to the film surface. A large number of misfit dislocations are introduced around the Fe/Cu interface due to an accommodation of lattice mismatch. Dislocations exist up to the film near surface. The lattice constant is estimated by XRD to be a = 0.3607 nm. The film shows a ferromagnetic property, which reflects the property of fcc-Fe crystal with high-spin ferromagnetic state.

36 MATERIALS SCIENCE↗

Enhancement of several Kikuchi lines in the vicinity of spot reflections

Kikuchi electron diffraction patterns of silicon have been obtained which demonstrate the simultaneous enhancement of several excess Kikuchi lines near different point reflections. This enhancement is explained within the elementary mechanism of the formation of Kikuchi patterns while taking into account the Kikuchi electron double diffraction.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Structure of the toxic core of α-synuclein from invisible crystals

We report that the protein α-synuclein is the main component of Lewy bodies, the neuron-associated aggregates seen in Parkinson disease and other neurodegenerative pathologies. An 11-residue segment, which we term NACore, appears to be responsible for amyloid formation and cytotoxicity of human α-synuclein. Here we describe crystals of NACore that have dimensions smaller than the wavelength of visible light and thus are invisible by optical microscopy. As the crystals are thousands of times too small for structure determination by synchrotron X-ray diffraction, we use micro-electron diffraction to determine the structure at atomic resolution. The 1.4 Å resolution structure demonstrates that this method can determine previously unknown protein structures and here yields, to our knowledge, the highest resolution achieved by any cryo-electron microscopy method to date. The structure exhibits protofibrils built of pairs of face-to-face β-sheets. X-ray fibre diffraction patterns show the similarity of NACore to toxic fibrils of full-length α-synuclein. Finally, the NACore structure, together with that of a second segment, inspires a model for most of the ordered portion of the toxic, full-length α-synuclein fibril, presenting opportunities for the design of inhibitors of α-synuclein fibrils.

Lewy bodies↗

Hydrothermal synthesis and luminescent properties of LuBO{sub 3}:Tb{sup 3+} microflowers

Hexagonal vaterite-type LuBO{sub 3}:Tb{sup 3+} microflower-like phosphors have been successfully prepared by an efficient surfactant- and template-free hydrothermal process directly without further sintering treatment. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), thermogravimetric analysis (TGA), scanning electron microscopy (SEM), energy-dispersive X-ray (EDX) spectrometry, transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron diffraction (SAED), photoluminescence (PL) and cathodoluminescence (CL) spectra as well as kinetic decays were used to characterize the samples. The as-obtained phosphor samples present flowerlike agglomerates composed of nanoflakes with thickness of 40 nm and high crystallinity in spite of the moderate reaction temperature of 200 deg. C. The reaction mechanism has been considered as a dissolution/precipitation mechanism; the self-assembly evolution process has been proposed on homocentric layer-by-layer growth style. Under ultraviolet excitation into the 4f{sup 8}{yields}4f{sup 7}5d transition of Tb{sup 3+} at 248 nm (or 288 nm) and low-voltage electron beam excitation, LuBO{sub 3}:Tb{sup 3+} samples show the characteristic green emission of Tb{sup 3+} corresponding to {sup 5}D{sub 4}{yields}{sup 7}F{sub 6,5,4,3} transitions with the {sup 5}D{sub 4}{yields}{sup 7}F{sub 5} transition (542 nm) being the most prominent group, which have potential applications in fluorescent lamps and field emission displays. - Graphical abstract: Hexagonal vaterite-type LuBO{sub 3}:Tb{sup 3+} microflower-like phosphors have been successfully prepared by a simple and mild hydrothermal process directly. The reaction mechanism has been considered as the dissolution/precipitation mechanism; the self-assembly evolution process has been proposed on homocentric layer-by-layer growth style. The luminescent properties of the as-obtained LuBO{sub 3}:Tb{sup 3+} samples have been investigated in detail, which shows it is a good green-emitting phosphor in fluorescent lamps and field emission displays potentially.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Structure and microstructure of the high pressure synthesised misfit layer compound [Sr{sub 2}O{sub 2}][CrO{sub 2}]{sub 1.85}

The strontium chromium oxide [Sr{sub 2}O{sub 2}][CrO{sub 2}]{sub 1.85} misfit layer compound has been synthesised at high-pressure and high-temperature conditions. Electron diffraction patterns and high-resolution transmission electron microscopy images along [001] show the misfit character of the different layers composing the structure with a supercell along the incommensurate parameter b{approx}7b{sub 1}{approx}13b{sub 2}. The modulated crystal structure has been refined within the superspace formalism against single-crystal X-ray diffraction data, employing the (3+1)-dimensional superspace group C'nmb(0{sigma}{sub 2}0)0 0 s. The compound has a composite structure with lattice parameters a{sub 1}=5.182(1) A, b{sub 1}=5.411(1) A, c{sub 1}=18.194(3) A for the first, SrO, subsystem and the same a and c, but with b{sub 2}=2.925(1) A for the second, CrO{sub 2}, subsystem. The layer stacking is similar to that of orthorhombic PbS(TiS{sub 2}){sub 1.18}, but with a much stronger intersubsytem bonding in the case of the oxide. The intersubsystem lattice mismatch is mainly handled by displacement modulations of the Sr atoms, correlated with modulations of the valence, the coordination and the anisotropic displacement parameters. - Graphical abstract: A strontium chromium oxide, [Sr{sub 2}O{sub 2}][CrO{sub 2}]{sub 1.85}, with an orthorhombic misfit layer structure has been synthesised under high pressure. Mainly modulations on the Sr position, ADPs and coordination save the subsystems lattice mismatch.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of δ-Bi2O3/Bi2MoO6 composites with enhanced photocatalytic activity by hydrothermal method

Highlights: • The δ-Bi{sub 2}O{sub 3}/Bi{sub 2}MoO{sub 6} composites were first synthesized by hydrothermal method. • The product was δ-Bi{sub 2}O{sub 3} rather than α-Bi{sub 2}O{sub 3} with the preset of Bi{sub 2}MoO{sub 6}. • The composites show enhanced photocatalytic activity compared to Bi{sub 2}MoO{sub 6}, α- and δ-Bi{sub 2}O{sub 3}. • The excellent photocatalytic performance was attributed to δ- Bi{sub 2}O{sub 3}/Bi{sub 2}MoO{sub 6} heterojunctions. - Abstract: The δ-Bi{sub 2}O{sub 3}/Bi{sub 2}MoO{sub 6} composites were synthesized by hydrothermal method and the microstructure and photocatalytic property were characterized. The X-ray diffraction (XRD) analysis revealed that δ-Bi{sub 2}O{sub 3} was obtained with the existence of Bi{sub 2}MoO{sub 6}, while the product was α-Bi{sub 2}O{sub 3} without Bi{sub 2}MoO{sub 6} under the same experimental condition. The SEM images and the selected area electron diffraction (SAED) patterns have further verified that δ-Bi{sub 2}O{sub 3} was deposited on Bi{sub 2}MoO{sub 6}. The X-ray photoelectron spectroscopy (XPS) spectrum confirmed that the composites were composed of δ-Bi{sub 2}O{sub 3} and Bi{sub 2}MoO{sub 6}, while a fraction of Mo changed from Mo{sup 6+} to Mo{sup 5+}. The coexistence of Mo{sup 5+}/Mo{sup 6+} can be a critical factor in the formation of stable δ-Bi{sub 2}O{sub 3} on Bi{sub 2}MoO{sub 6}. Particularly, the δ-Bi{sub 2}O{sub 3}/Bi{sub 2}MoO{sub 6} photocatalysts possess favorable photocatalytic performance under simulated sunlight illumination since the recombination of photogenerated electrons and holes was inhibited due to the p-n junction at the interface of δ-Bi{sub 2}O{sub 3} and Bi{sub 2}MoO{sub 6}, and the mechanism was discussed in detail.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl: A rare example of Ti(IV) in a square pyramidal oxygen coordination

A new oxychloride Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl has been synthesized using the solid state method. Its crystal and magnetic structure was investigated in the 1.5–550 K temperature range using electron diffraction, high angle annular dark field scanning transmission electron microscopy, atomic resolution energy dispersive X-ray spectroscopy, neutron and X-ray powder diffraction. At room temperature Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl crystallizes in the P4/mmm space group with the unit cell parameters a=3.91803(3) Å and c=19.3345(2) Å. Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl is a new n=4 member of the oxychloride perovskite-based homologous series A{sub n+1}B{sub n}O{sub 3n−1}Cl. The structure is built of truncated Pb{sub 3}Fe{sub 3}TiO{sub 11} quadruple perovskite blocks separated by CsCl-type Pb{sub 2}Cl slabs. The perovskite blocks consist of two layers of (Fe,Ti)O{sub 6} octahedra sandwiched between two layers of (Fe,Ti)O{sub 5} square pyramids. The Ti{sup 4+} cations are preferentially located in the octahedral layers, however, the presence of a noticeable amount of Ti{sup 4+} in a five-fold coordination environment has been undoubtedly proven using neutron powder diffraction and atomic resolution compositional mapping. Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl is antiferromagnetically ordered below 450(10) K. The ordered Fe magnetic moments at 1.5 K are 4.06(4) μ{sub B} and 3.86(5) μ{sub B} on the octahedral and square-pyramidal sites, respectively. - Highlights: • Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl has been synthesized using the solid state method. • The structure has been refined using neutron powder diffraction data at 1.5–550 K. • It is a new n=4 member of the perovskite-related homologous series A{sub n+1}B{sub n}O{sub 3n−1}Cl. • Ti{sup 4+} cations have both octahedral and square-pyramidal coordination environment. • Pb{sub 5}Fe{sub 3}TiO{sub 11}Cl is antiferromagnetically ordered below T{sub N}≈450 K.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Investigations of cations distributions and morphology of cobalt ferrite magnetic nanoparticles

Cobalt ferrite nanoparticles were synthesized by co-precipitation method and structural properties was investigated by X-ray diffraction (XRD) at room temperature. X-ray diffraction data was used to determine lattice parameter, X-ray density, distributions of cations among tetrahedral and octahedral sites, site radii, ionic radii and bond length of inverse spinel cobalt ferrite. XRD analysis revealed crystallinity and high intense peak correspond to cubic inverse spinel structure with average crystalline size measured by X-ray line profile fitting was found to be 13nm for most intense peak (311). The surface morphology and microstructural feature was investigated by TEM analysis which revealed that particle size varying from 12-22 nm with selected electron diffraction pattern (SAED).

77 NANOSCIENCE AND NANOTECHNOLOGY↗