Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electron Transistor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Displacement Damage in Bipolar Linear Integrated Circuits

Although many different processes can be used to manufacture linear integrated circuits, the process that is used for most circuits is optimized for high voltage -- a total power supply voltage of about 40 V -- and low cost. This process, which has changed little during the last twenty years, uses lateral and substrate p-n-p transistors. These p-n-p transistors have very wide base regions, increasing their sensitivity to displacement damage from electrons and protons. Although displacement damage effects can be easily treated for individual transistors, the net effect on linear circuits can be far more complex because circuit operation often depends on the interaction of several internal transistors. Note also that some circuits are made with more advanced processes with much narrower base widths. Devices fabricated with these newer processes are not expected to be significantly affected by displacement damage for proton fluences below 1 x 10(exp 12) p/sq cm. This paper discusses displacement damage in linear integrated circuits with more complex failure modes than those exhibited by simpler devices, such as the LM111 comparator, where the dominant response mode is gain degradation of the input transistor. Some circuits fail catastrophically at much lower equivalent total dose levels compared to tests with gamma rays. The device works satisfactorily up to nearly 1 Mrad(Si) when it is irradiated with gamma rays, but fails catastrophically between 50 and 70 krad(Si) when it is irradiated with protons.

Rax, B. G.↗

Protonic/electronic hybrid oxide transistor gated by chitosan and its full-swing low voltage inverter applications

Modulation of charge carrier density in condensed materials based on ionic/electronic interaction has attracted much attention. Here, protonic/electronic hybrid indium-zinc-oxide (IZO) transistors gated by chitosan based electrolyte were obtained. The chitosan-based electrolyte illustrates a high proton conductivity and an extremely strong proton gating behavior. The transistor illustrates good electrical performances at a low operating voltage of ∼1.0 V such as on/off ratio of ∼3 × 10{sup 7}, subthreshold swing of ∼65 mV/dec, threshold voltage of ∼0.3 V, and mobility of ∼7 cm{sup 2}/V s. Good positive gate bias stress stabilities are obtained. Furthermore, a low voltage driven resistor-loaded inverter was built by using an IZO transistor in series with a load resistor, exhibiting a linear relationship between the voltage gain and the supplied voltage. The inverter is also used for decreasing noises of input signals. The protonic/electronic hybrid IZO transistors have potential applications in biochemical sensors and portable electronics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Materials and Electrical Characterization of Physical Vapor Deposited LaxLu1-xO3 Thin Films on 300 mm Silicon

La{sub x}Lu{sub 1-x}O{sub 3} thin films were deposited on 300 mm silicon wafers by physical vapor deposition and fabricated into field-effect transistors using a gate-first process flow. The films were characterized using transmission electron microscopy, Rutherford backscattering spectrometry, and synchrotron x-ray diffraction. The results show the films remain amorphous even at temperatures of 1000 C. The dielectric properties of La{sub x}Lu{sub 1-x}O{sub 3} (0.125 {<=} x {<=} 0.875) thin films were evaluated as a function of film composition. The amorphous La{sub x}Lu{sub 1-x}O{sub 3} thin films have a dielectric constant (K) of 23 across the composition range. The inversion thickness (T{sub inv}) of the La{sub x}Lu{sub 1-x}O{sub 3} thin films was scaled to <1.0 nm.

36 MATERIALS SCIENCE↗

A Water-Based Silver-Nanowire Screen-Print Ink for the Fabrication of Stretchable Conductors and Wearable Thin-Film Transistors

Silver nanowire is a very promising material for fabricating compliant conductors which are essential for stretchable/wearable electronic devices. Screen printing is a cost-effective and scalable technology to fabricate large-area thin film coatings with modest pattern resolution. The biggest challenge to prepare a screen printable silver nanowire ink stems from the low viscosity of silver nanowire dispersions and that the addition of a thickening agent could dramatically increase the inter-nanowire contact resistance in the resulting coating. Herein, we report the synthesis of a water-based silver nanowire ink, which was formulated with low solid contents, high viscosity at 0.1 s -1 shear rate, and appropriate rheological behavior suitable for screen printing. Silver nanowire coating patterns were screen printed with uniform sharp edges, ~50 μm resolution, and electrical conductivity as high as 4.67 × 10 4 S cm -1 . The screen printed silver nanowires were then used to fabricate a composite conductor that retained a conductivity greater than 10,000 S cm -1 under 70% tensile strain. Fully printed and stretchable/wearable thin-film transistor arrays were also fabricated by employing the screen printed composite conductor as the source, drain, and gate, drop cast semiconducting carbon nanotubes as the channel, and a dielectric elastomer. The 10 × 6 thin-film transistor arrays had a fabrication yield of 91.7%, average mobility of 33.8 ± 3.7 cm 2 V -1 s -1 , ON/OFF ratio ~1000, and remained stable during 1,000 cycles of wearing on and peeling off a glass tube with 5 mm diameter.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Palladium nanoparticle decorated silicon nanowire field-effect transistor with side-gates for hydrogen gas detection

A silicon nanowire field-effect transistor (SiNW FET) with local side-gates and Pd surface decoration is demonstrated for hydrogen (H{sub 2}) detection. The SiNW FETs are fabricated by top-down method and functionalized with palladium nanoparticles (PdNPs) through electron beam evaporation for H{sub 2} detection. The drain current of the PdNP-decorated device reversibly responds to H{sub 2} at different concentrations. The local side-gates allow individual addressing of each sensor and enhance the sensitivity by adjusting the working region to the subthreshold regime. A control experiment using a non-functionalized device verifies that the hydrogen-sensitivity is originated from the PdNPs functionalized on the SiNW surface.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Transparent ferromagnetic and semiconducting behavior in Fe-Dy-Tb based amorphous oxide films

We report a class of amorphous thin film material comprising of transition (Fe) and Lanthanide metals (Dy and Tb) that show unique combination of functional properties. Films were deposited with different atomic weight ratio (R) of Fe to Lanthanide (Dy+Tb) using electron beam co-evaporation at room temperature. The films were found to be amorphous, with grazing incidence x-ray diffraction and x-ray photoelectron spectroscopy studies indicating that the films were largely oxidized with a majority of the metal being in higher oxidation states. Films with R=0.6 were semiconducting with visible light transmission due to a direct optical band-gap (2.49eV), had low resistivity and sheet resistance (7.15×10-4Ω-cm and ~200Ω/sq respectively), and showed room temperature ferromagnetism. A metal to semiconductor transition with composition (for R<11.9) also correlated well with the absence of any metallic Fe0 oxidation state in the R=0.6 case as well as a significantly higher fraction of oxidized Dy. The combination of amorphous microstructure and room temperature electronic and magnetic properties could lead to the use of the material in multiple applications, including as a transparent conductor, active material in thin film transistors for display devices, and in spin-dependent electronics.

36 MATERIALS SCIENCE↗

Elimination of the bias-stress effect in ligand-free quantum dot field-effect transistors

Field-effect transistors (FETs) made from colloidal quantum dot (QD) solids commonly suffer from current–voltage hysteresis caused by the bias-stress effect (BSE), which complicates fundamental studies of charge transport in QD solids and the use of QD FETs in electronics. Here, we show that the BSE can be eliminated in n-channel PbSe QD FETs by first removing the QD ligands with a dose of H 2 S gas and then infilling the QD films with alumina by atomic layer deposition (ALD). The H 2 S-treated, alumina-infilled FETs have stable, hysteresis-free device characteristics (total short-term stability), indefinite air stability (total long-term stability), and a high electron mobility of up to 14 cm 2 V −1 s −1 , making them attractive for QD circuitry and optoelectronic devices. The BSE-free devices are utilized to conclusively establish the dependence of the electron mobility on temperature and QD diameter. We demonstrate that the BSE in these devices is caused by both electron trapping at the QD surface and proton drift within the film. The H 2 S/alumina chemistry produces ligand-free PbSe/PbS/Al 2 O 3 interfaces that lack the traps that cause the electronic part of the BSE, while full alumina infilling stops the proton motion responsible for the ionic part of the BSE. In conclusion, our matrix engineering approach should aid efforts to eliminate the BSE, boost carrier mobilities, and improve charge transport in other types of nanocrystal solids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Deterministic assembly of releasable single crystal silicon-metal oxide field-effect devices formed from bulk wafers

Deterministic assembly of ultrathin metal oxide-semiconductor field-effect transistors released from the surfaces of bulk wafers with (111) orientation provides a route to high quality electronics on nearly any type of substrate. Device parameters and bias stability characteristics from transistors on sheets of plastic confirm the effectiveness of the approach and the critical roles of thermally grown layers of silicon dioxide for the gate dielectrics and passivation layers. Here, systematic studies of the anisotropic etching processes used to release the devices illustrate capabilities into the sub-micron thickness regime, with beneficial effects on the bending stiffness and degree of bendability.

36 MATERIALS SCIENCE↗

Improving chemical vapor deposition graphene conductivity using molybdenum trioxide: An in-situ field effect transistor study

By using in situ field effect transistor characterization integrated with molecular beam epitaxy technique, we demonstrate the strong surface transfer p-type doping effect of single layer chemical vapor deposition (CVD) graphene, through the surface functionalization of molybdenum trioxide (MoO{sub 3}) layer. After doping, both the hole and electron mobility of CVD graphene are nearly retained, resulting in significant enhancement of graphene conductivity. With coating of 10 nm MoO{sub 3}, the conductivity of CVD graphene can be increased by about 7 times, showing promising application for graphene based electronics and transparent, conducting, and flexible electrodes.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Amorphous oxide alloys as interfacial layers with broadly tunable electronic structures for organic photovoltaic cells

In diverse classes of organic optoelectronic devices, controlling charge injection, extraction, and blocking across organic semiconductor– inorganic electrode interfaces is crucial for enhancing quantum efficiency and output voltage. To this end, the strategy of inserting engineered interfacial layers (IFLs) between electrical contacts and organic semiconductors has significantly advanced organic light-emitting diode and organic thin film transistor performance. For organic photovoltaic (OPV) devices, an electronically flexible IFL design strategy to incrementally tune energy level matching between the inorganic electrode system and the organic photoactive components without varying the surface chemistry would permit OPV cells to adapt to ever-changing generations of photoactive materials. Here we report the implementation of chemically/environmentally robust, low-temperature solution-processed amorphous transparent semiconducting oxide alloys, In-Ga-O and Ga-Zn-Sn-O, as IFLs for inverted OPVs. Lastly, continuous variation of the IFL compositions tunes the conduction band minima over a broad range, affording optimized OPV power conversion efficiencies for multiple classes of organic active layer materials and establishing clear correlations between IFL/photoactive layer energetics and device performance.

25 ENERGY STORAGE↗

Template-assisted selective epitaxy of III–V nanoscale devices for co-planar heterogeneous integration with Si

III–V nanoscale devices were monolithically integrated on silicon-on-insulator (SOI) substrates by template-assisted selective epitaxy (TASE) using metal organic chemical vapor deposition. Single crystal III–V (InAs, InGaAs, GaAs) nanostructures, such as nanowires, nanostructures containing constrictions, and cross junctions, as well as 3D stacked nanowires were directly obtained by epitaxial filling of lithographically defined oxide templates. The benefit of TASE is exemplified by the straightforward fabrication of nanoscale Hall structures as well as multiple gate field effect transistors (MuG-FETs) grown co-planar to the SOI layer. Hall measurements on InAs nanowire cross junctions revealed an electron mobility of 5400 cm{sup 2}/V s, while the alongside fabricated InAs MuG-FETs with ten 55 nm wide, 23 nm thick, and 390 nm long channels exhibit an on current of 660 μA/μm and a peak transconductance of 1.0 mS/μm at V{sub DS} = 0.5 V. These results demonstrate TASE as a promising fabrication approach for heterogeneous material integration on Si.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Zinc Oxide Thin Films Fabricated with Direct Current Magnetron Sputtering Deposition Technique

Zinc oxide (ZnO) is a very promising material for emerging large area electronic applications including thin-film sensors, transistors and solar cells. We fabricated ZnO thin films by employing direct current (DC) magnetron sputtering deposition technique. ZnO films with different thicknesses ranging from 100 nm to 1020 nm were deposited on silicon (Si) substrate. The deposition pressure was varied from 12 mTorr to 25 mTorr. The influences of the film thickness and the deposition pressure on structural properties of the ZnO films were investigated using Mahr surface profilometer and atomic force microscopy (AFM). The experimental results reveal that the film thickness and the deposition pressure play significant role in the structural formation of the deposited ZnO thin films. ZnO films deposited on Si substrates are promising for variety of thin-film sensor applications.

36 MATERIALS SCIENCE↗

Maximized Hole Trapping in a Polystyrene Transistor Dielectric from a Highly Branched Iminobis(aminoarene) Side Chain

We synthesized highly branched and electron donating side chain subunits and attached them to polystyrene (PS) used as a dielectric layer in a pentacene field effect transistor. The influence of these groups on dielectric function, charge retention and threshold voltage shifts (ΔV th ) depending on their positions in dielectric multilayers was determined. We compared the observations made on an N-perphenylated iminobisaniline side chain with those from the same side chains modified with ZnO nanoparticles and with an adduct formed from tetracyanoethylene (TCNE). We also synthesized an analogue in which six methoxy groups are present instead of two amine nitrogens. At 6 mol % side chain, hopping transport was sufficient to cause shorting of the gate, while at 2 mol %, charge trapping was observable as transistor threshold voltage shifts (ΔV th ). Here, we created three types of devices: with the substituted PS layer as single layer dielectric, on top of a crosslinked PS layer but in contact with the pentacene (bilayers), and sandwiched between two PS layers in trilayers. Particularly large bias stress effects and ΔV th , larger than the hexamethoxy and previously studied dimethoxy analogs, were observed in the second case and the effects increased with the increasing electron donating properties of the modified side chains. The highest ΔV th was consistent with a majority of the side chains stabilizing trapped charge. Trilayer devices showed decreased charge storage capability compared to previous work in which we used less donating side chains but in higher concentrations. The ZnO and TCNE modifications resulted in slightly more and less negative ΔV th , respectively, when the side chain polystyrene was not in contact with the pentacene and isolated from the gate electrode. The results indicate a likely maximum combination of molecular charge stabilizing activity and side chain concentration that still allows gate dielectric function.

36 MATERIALS SCIENCE↗

Modulation of over 10{sup 14} cm{sup −2} electrons in SrTiO{sub 3}/GdTiO{sub 3} heterostructures

We demonstrate charge modulation of over 10{sup 14} cm{sup −2} electrons in a two-dimensional electron gas formed in SrTiO{sub 3}/GdTiO{sub 3} inverted heterostructure field-effect transistors. Increased charge modulation was achieved by reducing the effect of interfacial region capacitances through thick SrTiO{sub 3} cap layers. Transport and device characteristics of the heterostructure field-effect transistors were found to match a long channel field effect transistor model. SrTiO{sub 3} impurity doped metal–semiconductor field effect transistors were also demonstrated with excellent pinch-off and current density exceeding prior reports. The work reported here provides a path towards oxide-based electronics with extreme charge modulation exceeding 10{sup 14} cm{sup −2}.

36 MATERIALS SCIENCE↗

Insights into negative differential resistance in MoS 2 Esaki diodes: A first-principles perspective

MoS 2 is a two-dimensional material with a band gap depending on the number of layers and tunable by an external electric field. The experimentally observed intralayer band-to-band tunneling and interlayer band-to-band tunneling in this material present an opportunity for new electronic applications in tunnel field-effect transistors. However, such a widely accepted concept has yet to be been supported by theoretical investigations based on first principles. In this paper, using density functional theory, in conjunction with nonequilibrium Green's function techniques and our electric field gating method, enabled by a large-scale computational approach, we study the relation between band alignment and transmission in planar and side-stack MoS 2 p–i–n junction configurations. Here, we demonstrate the presence of negative differential resistance for both in-plane and interlayer current, a staple characteristic of tunnel diode junctions, and analyze the physical origin of such an effect. Electrostatic potentials, the van der Waals barrier, and a complex band analysis are also examined for a thorough understanding of Esaki diodes.

74 ATOMIC AND MOLECULAR PHYSICS↗

First principles study of metal contacts to monolayer black phosphorous

Atomically thin layered black phosphorous (BP) has recently appeared as an alternative to the transitional metal dichalcogenides for future channel material in a metal-oxide-semiconductor transistor due to its lower carrier effective mass. Investigation of the electronic property of source/drain contact involving metal and two-dimensional material is essential as it impacts the transistor performance. In this paper, we perform a systematic and rigorous study to evaluate the Ohmic nature of the side-contact formed by the monolayer BP (mBP) and metals (gold, titanium, and palladium), which are commonly used in experiments. Employing the Density Functional Theory, we analyse the potential barrier, charge transfer and atomic orbital overlap at the metal-mBP interface in an optimized structure to understand how efficiently carriers could be injected from metal contact to the mBP channel. Our analysis shows that gold forms a Schottky contact with a higher tunnel barrier at the interface in comparison to the titanium and palladium. mBP contact with palladium is found to be purely Ohmic, where as titanium contact demonstrates an intermediate behaviour.

36 MATERIALS SCIENCE↗

Metastable Copper-Phthalocyanine Single-Crystal Nanowires and Their Use in Fabricating High-Performance Field-Effect Transistors

This paper describes a simple, vapor-phase route to the synthesis of metastable α-phase copper-phthalocyanine (CuPc) single-crystal nanowires through control of the growth temperature. The influence of the growth temperature on the crystal structures, morphology, and size of the CuPc nanostructures was explored by XRD, optical absorption and Transmission Electron Microscopy (TEM). α-CuPc nanowires were successfully incorporated as active semiconductors in field-effect transistors (FETs). Single nanowire devices exhibited the carrier mobilities and current on/off ratios as high as 0.4 cm2/Vs and > 104, respectively, rendering them useful for organic photovoltaic cells, organic light-emitting diodes, field-effect transistors, memories and gas sensors

14 SOLAR ENERGY↗