Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Dynamic Procedures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Hybrid methods for rotordynamic analysis

Effective procedures are presented for the response analysis of the Space Shuttle Main Engine turbopumps under transient loading conditions. Of particular concern is the determination of the nonlinear response of the systems to rotor imbalance in presence of bearing clearances. The proposed procedures take advantage of the nonlinearities involved being localized at only a few rotor/housing coupling joints. The methods include those based on integral formulations for the incremental solutions involving the transition matrices of the rotor and housing. Alternatively, a convolutional representation of the housing displacements at the coupling points is proposed which would allow performing the transient analysis on a reduced model of the housing. The integral approach is applied to small dynamical models to demonstrate the efficiency of the approach. For purposes of assessing the numerical integration results for the nonlinear rotor/housing systems, a numerical harmonic balance procedure is developed to enable determining all possible harmonic, subharmonic, and nonperiodic solutions of the systems. A brief account of the Fourier approach is presented as applied to a two degree of freedon rotor-support system.

Noah, Sherif T.↗

Minimum mass sizing of a large low-aspect ratio airframe for flutter-free performance

A procedure for sizing an airframe for flutter-free performance is demonstrated on a large, flexible supersonic transport aircraft. The procedure is based on using a two-level reduced basis or modal technique for reducing the computational cost of performing the repetitive flutter analyses. The supersonic transport aircraft exhibits complex dynamic behavior, has a well-known flutter problem and requires a large finite-element model to predict the vibratory and flutter response. Flutter-free designs are produced with small mass increases relative to the wing structural weight and aircraft payload. In view of the ability of the resizing procedure to handle this supersonic transport configuration, it seems likely that the method could be used for many other aircraft.

Greene, W. H.↗

Treating convection in sequential solvers

The treatment of the convection terms in the sequential solver, a standard procedure found in virtually all pressure based algorithms, to compute the flow problems with sharp gradients and source terms is investigated. Both scalar model problems and one-dimensional gas dynamics equations have been used to study the various issues involved. Different approaches including the use of nonlinear filtering techniques and adoption of TVD type schemes have been investigated. Special treatments of the source terms such as pressure gradients and heat release have also been devised, yielding insight and improved accuracy of the numerical procedure adopted.

Shyy, Wei↗

MAVRIC Flutter Model Transonic Limit Cycle Oscillation Test

The Models for Aeroelastic Validation Research Involving Computation semi-span wind-tunnel model (MAVRIC-I), a business jet wing-fuselage flutter model, was tested in NASA Langley's Transonic Dynamics Tunnel with the goal of obtaining experimental data suitable for Computational Aeroelasticity code validation at transonic separation onset conditions. This research model is notable for its inexpensive construction and instrumentation installation procedures. Unsteady pressures and wing responses were obtained for three wingtip configurations clean, tipstore, and winglet. Traditional flutter boundaries were measured over the range of M = 0.6 to 0.9 and maps of Limit Cycle Oscillation (LCO) behavior were made in the range of M = 0.85 to 0.95. Effects of dynamic pressure and angle-of-attack were measured. Testing in both R134a heavy gas and air provided unique data on Reynolds number, transition effects, and the effect of speed of sound on LCO behavior. The data set provides excellent code validation test cases for the important class of flow conditions involving shock-induced transonic flow separation onset at low wing angles, including Limit Cycle Oscillation behavior.

Edwards, John W.↗

Data-driven modeling and control of dynamical systems using Koopman and Perron-Frobenius operators

This dissertation studies the data-driven modeling and control problem of nonlinear systems by exploiting the linear operator theoretic framework involving Koopman and Perro-Frobenius operator. A systematic linear-operator based controller design procedure has been established, which can be used to solve a variety of nonlinear control problems, including feedback stabilization using control Lyapunov functions, optimal quadratic regulation using Koopman eigenfunctions and convex optimization formulation of optimal control problem using P-F and Koopman operator approximation. As the core of data-driven modeling, we first propose a new algorithm for the finite-dimensional approximation of the linear transfer Koopman and Perron-Frobenius operator from time-series data. We argue that the existing approach for the finite-dimensional approximation of these transfer operators such as Dynamic Mode Decomposition (DMD) and Extended Dynamic Mode Decomposition (EDMD) do not capture two important properties of these operators, namely positivity and Markov property. The algorithm we propose preserves these two properties. We call the proposed algorithm as naturally structured DMD (NSDMD) since it retains the inherent properties of these operators. Naturally structured DMD algorithm leads to a better approximation of the steady-state dynamics of the system regarding computing Koopman and Perron- Frobenius operator eigenfunctions and eigenvalues. However, preserving positivity property is critical for capturing the real transient dynamics of the system. This positivity property of the transfer operators and it's finite-dimensional approximation play an important role for controller and estimator design of nonlinear systems. To solve the feedback stabilization problem for nonlinear control systems, we tried to take advantage of the Koopman operator framework. The Koopman operator approach provides a linear representation for a nonlinear dynamical system and a bilinear representation for a nonlinear control system. The problem of feedback stabilization of a nonlinear control system is then transformed to the stabilization of a bilinear control system. We propose a control Lyapunov function (CLF)-based approach for the design of stabilizing feedback controllers for the bilinear system. The search for finding a CLF for the bilinear control system is formulated as a convex optimization problem. This leads to a schematic procedure for designing CLF-based stabilizing feedback controllers for the bilinear system and hence the original nonlinear system. Another advantage of the proposed controller design approach outlined in this dissertation is that it does not require explicit knowledge of system dynamics. In particular, the bilinear representation of a nonlinear control system in the Koopman eigenfunction space can be obtained from time-series data. Next, we study the optimal quadratic regulation problem for nonlinear systems. The linear operator theoretic framework involving the Koopman operator is used to lift the dynamics of nonlinear control system to an infinite-dimensional bilinear system. The optimal quadratic regulation problem for nonlinear system is formulated in terms of the finite-dimensional approximation of the bilinear system. A convex optimization-based approach is proposed for solving the quadratic regulator problem for bilinear system. We applied a variety of examples and compared the simulation results between our framework and conventional LQR control using linearized model. For more general optimal control problems, we provide a density-function based convex formulation for the optimal control problem of the nonlinear system. The convex formulation relies on the duality result in the stability theory of a dynamical system involving density function and Perron-Frobenius operator. The optimal control problem is formulated as an infinite-dimensional convex optimization program. The finite-dimensional approximation of the optimization problem relies on the recent advances made in the data-driven computation of the Koopman operator, which is dual to the Perron-Frobenius operator. Simulation results are presented to demonstrate the application of the developed framework.

Huang, Bowen↗

A novel two-layer-integrated microfluidic device for high-throughput yeast proteomic dynamics analysis at the single-cell level

Abstract Current microfluidic methods for studying multicell strains (e.g., m-types) with multienvironments (e.g., n-types) require large numbers of inlets/outlets (m*n), a complicated procedure or expensive machinery. Here, we developed a novel two-layer-integrated method to combine different PDMS microchannel layers with different functions into one chip by a PDMS through-hole array, which improved the design of a PDMS-based microfluidic system. Using this method, we succeeded in converting 2 × m × n inlets/outlets into m + n inlets/outlets and reduced the time cost of loading processing (from m × n to m) of the device for studying multicell strains (e.g., m-types) in varied multitemporal environments (i.e., n-types). Using this device, the dynamic behavior of the cell-stress-response proteins was studied when the glucose concentration decreased from 2% to a series of lower concentrations. Our device could also be widely used in high-throughput studies of various stress responses, and the new concept of a multilayer-integrated fabrication method could greatly improve the design of PDMS-based microfluidic systems.

Chen, Kaiyue↗

Polymer Macrocycles: A novel topology to control dynamics of rubbery materials (Final Report)

One of the current challenges in polymer physics and engineering is to understand the behavior of circular macromolecules. Though such molecules have been made by dilute solution ring closure methods in the past, such procedures have been limited to relatively small, unentangled rings as well as to small sample quantities. Initial studies were also hampered by issues surrounding purity of the rings, though this problem has been somewhat overcome by the use of liquid chromatography at critical conditions (LCCC) methods that separate rings and linear chains. Furthermore, in spite of the continued progress a full understanding of ring dynamics remains elusive. The present work has addressed multiple aspects of the behavior of ring molecules by using a novel synthetic route: reversible radical recombination redox polymerization (R3P) to produce poly(3,6-dioxa-1,8-octanedithiol) (PolyDODT) molecules. The synthesis conditions were chosen to produce linear (LDODT), cyclic (RDODT) and linear-cyclic mixtures (LRDODT) in order to investigate dilute solution and rheological responses of the materials. Importantly, the R3P synthesis makes larger quantities and higher molecular weights than do the dilute solution ring closure methods and also has the potential to be scaled to industrial quantities, thus becoming commercializable. We emphasize two important outcomes of the work. The first is that the rheological investigation shows that very large molecular weight the PolyDODT rings permitted the investigation of ring dynamics from glassy towards terminal flow for molecular sizes corresponding to approximately 300 entanglements of the linear counterpart. At the same time, these very large sized rings could be diluted in a solvent in order to reduce the molecular entanglement density to less than unity. The results demonstrate that ring viscosity follows a Rouse-like linear dependence on molecular weight or entanglement number to approximately 15 entanglements. This range of "Rouse-like" response is greater than what was achieved in all prior works where synthesis conditions have limited the molecular sizes achievable. After the entanglement number $Z_w$ increases beyond approximately 15, we find that the viscosity-molecular weight scaling undergoes a rapid change from the Rouse-like $η\sim{Z}^1_w$ to a very strong power-law scaling that is approximately $η\sim{Z}^{5.8}_w$. This aspect of the work strongly suggests that prior investigations on highly pure rings have invariably been performed on unentangled systems simply because ring molecules have very high entanglement thresholds. The results are further supported by plateau modulus measurements that show that in the "Rouse-like" viscosity regime, for the RDODT samples there is a corresponding lack of a rubbery entanglement plateau and once entanglement coupling is seen, the rubbery plateau also appears in the dynamic modulus data. Furthermore, upon appropriate scaling, we show that the unentangled polyDODT rings (i.e., the diluted high molecular weight rings) show virtually identical dynamics (upon appropriate scaling to account for the chain dilutions) to the dynamics of similarly unentangled LCCC fractionated polystyrene rings.

36 MATERIALS SCIENCE↗

MAVRIC Flutter Model Transonic Limit Cycle Oscillation Test

The Models for Aeroelastic Validation Research Involving Computation semi-span wind-tunnel model (MAVRIC-I), a business jet wing-fuselage flutter model, was tested in NASA Langley's Transonic Dynamics Tunnel with the goal of obtaining experimental data suitable for Computational Aeroelasticity code validation at transonic separation onset conditions. This research model is notable for its inexpensive construction and instrumentation installation procedures. Unsteady pressures and wing responses were obtained for three wingtip configurations of clean, tipstore, and winglet. Traditional flutter boundaries were measured over the range of M = 0.6 to 0.9 and maps of Limit Cycle Oscillation (LCO) behavior were made in the range of M = 0.85 to 0.95. Effects of dynamic pressure and angle-of-attack were measured. Testing in both R134a heavy gas and air provided unique data on Reynolds number, transition effects, and the effect of speed of sound on LCO behavior. The data set provides excellent code validation test cases for the important class of flow conditions involving shock-induced transonic flow separation onset at low wing angles, including LCO behavior.

Edwards, John W.↗

Development of procedures for calculating stiffness and damping properties of elastomers. Part 3: The effects of temperature, dissipation level and geometry

Effects of temperature, dissipation level and geometry on the dynamic behavior of elastomer elements were investigated. Force displacement relationships in elastomer elements and the effects of frequency, geometry and temperature upon these relationships are reviewed. Based on this review, methods of reducing stiffness and damping data for shear and compression test elements to material properties (storage and loss moduli) and empirical geometric factors are developed and tested using previously generated experimental data. A prediction method which accounts for large amplitudes of deformation is developed on the assumption that their effect is to increase temperature through the elastomers, thereby modifying the local material properties. Various simple methods of predicting the radial stiffness of ring cartridge elements are developed and compared. Material properties were determined from the shear specimen tests as a function of frequency and temperature. Using these material properties, numerical predictions of stiffness and damping for cartridge and compression specimens were made and compared with corresponding measurements at different temperatures, with encouraging results.

Smalley, A. J.↗

On the dynamics of chain systems

A computer-oriented method for obtaining dynamical equations of motion for chain systems is presented. A chain system is defined as an arbitrarily assembled set of rigid bodies such that adjoining bodies have at least one common point and such that closed loops are not formed. The equations of motion are developed through the use of Lagrange's form of d'Alembert's principle. The method and procedure is illustrated with an elementary study of a tripod space manipulator. The method is designed for application with systems such as human body models, chains and cables, and dynamic finite-segment models.

Huston, R. L.↗

PSA 2025 DPRA for Cyber Optimization

Cyberattacks can have many different attack paths, durations, and goals. There are also many different mitigation options involving hardware, software, and/or humans. Evaluating defense options should include quantitative evaluation of overall effectiveness to make cost and risk-informed decisions. Typical cyberattack modeling methods only provide a qualitative evaluation and have difficulty with time dependent scenarios. The main areas of cybersecurity are confidentiality, integrity, and availability. For companies with cyber-physical systems such as advanced nuclear reactors, cyber-related integrity is a requirement set by the U.S. Nuclear Regulatory Commission. But companies are also concerned about availability or reliability as a business case. As cyber threats are evolving to a business-for-hire structure, more attacks focus on disrupting business success and reliability, causing financial and economic stability risk. Companies want reliability analysis while optimizing cost, which requires more than safety modeling methods. Dynamic-state-based and Markov-based modeling provides a method for better cyber scenario modeling with timing and conditional features not found in other numerical evaluation methods. EMRALD (Event Modeling Risk Assessment using Lined Diagrams) is a dynamic risk analysis modeling and simulation tool and has features that reduce modeling issues such as state-base explosion found in Markov-based tools. It has been used to model different time-dependent events including plant behavior and operator procedures. As a general modeling tool, EMRALD can also be used to model cyberattack scenarios with varying mitigation options and quantify effectiveness, producing numerical data for risk-informed decisions. This paper uses EMRALD to demonstrate that dynamic risk analysis can be used for cyber threat modeling to provide insights for design decision-making and optimize defense strategies.

97 - MATHEMATICS AND COMPUTING↗

A note on higher-order and nonlinear limiting approaches for continuously bounds-preserving discontinuous Galerkin methods

In Dzanic (2024), a limiting approach for high-order discontinuous Galerkin schemes was introduced which allowed for imposing constraints on the solution continuously (i.e., everywhere within the element). While exact for linear constraint functionals, this approach only imposed a sufficient (but not the minimum necessary) amount of limiting for nonlinear constraint functionals. This short note shows how this limiting approach can be extended to allow exactness for general nonlinear quasiconcave constraint functionals through a nonlinear limiting procedure, reducing unnecessary numerical dissipation. Finally, some examples are shown for nonlinear pressure and entropy constraints in the compressible gas dynamics equations, where both analytic and iterative approaches are used.

97 MATHEMATICS AND COMPUTING↗

A model-based technique for predicting pilot opinion ratings for large commercial transports

A model-based technique for predicting pilot opinion ratings is described. Features of this procedure, which is based on the optimal-control model for pilot/vehicle systems, include (1) capability to treat 'unconventional' aircraft dynamics, (2) a relatively free-form pilot model, (3) a simple scalar metric for attentional workload, and (4) a straightforward manner of proceeding from descriptions of the flight task environment and requirements to a prediction of pilot opinion rating. The method is able to provide a good match to a set of pilot opinion ratings obtained in a manned simulation study of large commercial aircraft in landing approach.

Levison, W. H.↗

A model-based technique for predicting pilot opinion ratings for large commercial transports

A model-based technique for predicting pilot opinion ratings is described. Features of this procedure, which is based on the optimal-control model for pilot/vehicle systems, include (1) capability to treat "unconventional" aircraft dynamics, (2) a relatively free-form pilot model, (3) a simple scalar metric for attentional workload, and (4) a straightforward manner of proceeding from descriptions of the flight task environment and requirements to a prediction of pilot opinion rating. The method was able to provide a good match to a set of pilot opinion ratings obtained in a manned simulation study of large commercial aircraft in landing approach.

Levison, W. H.↗

On excitation of Earth's free wobble and reference frames

The excitation of the Earth's polar motion in connection with problems that are associated with the diversity of reference frames involved in observations and theoretical computations is studied. Following the dynamics of the Earth's polar motion, the kinematics that relates observations from different reference frames is developed. The conventional procedures of studying the seismic excitation of polar motion are re-examined, subject to the question: relative to what reference frame? It is concluded that an inconsistency in reference frames has prevailed in the literature. While this inconsistency is indeed far from trivial, the resultant discrepancy, however, is small for all practical purposes.

Chao, B. F.↗

Adaptive identification and control of structural dynamics systems using recursive lattice filters

A new approach for adaptive identification and control of structural dynamic systems by using least squares lattice filters thar are widely used in the signal processing area is presented. Testing procedures for interfacing the lattice filter identification methods and modal control method for stable closed loop adaptive control are presented. The methods are illustrated for a free-free beam and for a complex flexible grid, with the basic control objective being vibration suppression. The approach is validated by using both simulations and experimental facilities available at the Langley Research Center.

Sundararajan, N.↗

On the excitation of the earth's free wobble and reference frames

The excitation of the earth's polar motion in connection with problems that are associated with the diversity of reference frames involved in observations and theoretical computations is studied. Following the dynamics of the earth's polar motion, the kinematics that relates observations from different reference frames is developed. The conventional procedures of studying the seismic excitation of polar motion are re-examined, subject to the question: relative to what reference frame? It is concluded that an inconsistency in reference frames has prevailed in the literature. While this inconsistency is indeed far from trivial, the resultant discrepancy, however, is small for all practical purposes.

Chao, B. F.↗