Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DISCHARGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Discharge characteristics of an atmospheric-pressure argon plasma column generated with a single-electrode configuration

An atmospheric-pressure argon discharge plasma column is generated by making use of a single-electrode configuration with the power supply operating at a frequency of 45 kHz. It is observed that corona, glowlike plume, and filamentary discharges evolve individually with increasing applied voltage. It is in the filamentary state with average electron density of order 10{sup 12} cm{sup -3} that plasma column grows up in the tube with increasing applied voltage. Its discharge characteristics are determined by measuring electrical parameters (voltage, conduction current, and average absorbed power) and optical emission spectroscopy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Boron ion source based on planar magnetron discharge in self-sputtering mode

An ion source based on a planar magnetron sputtering device with thermally isolated target has been designed and demonstrated. For a boron sputtering target, high target temperature is required because boron has low electrical conductivity at room temperature, increasing with temperature. The target is well-insulated thermally and can be heated by an initial low-current, high-voltage discharge mode. A discharge power of 16 W was adequate to attain the required surface temperature (400 C), followed by transition of the discharge to a high-current, low-voltage mode for which the magnetron enters a self-sputtering operational mode. Beam analysis was performed with a time-of-flight system; the maximum boron ion fraction in the beam is greater than 99%, and the mean boron ion fraction, time-integrated over the whole pulse length, is about 95%. We have plans to make the ion source steady state and test with a bending magnet. This kind of boron ion source could be competitive to conventional boron ion sources that utilize compounds such as BF3, and could be useful for semiconductor industry application.

43 PARTICLE ACCELERATORS↗

Highly efficient pulsed power supply system with a two-stage LC generator and a step-up transformer for fast capillary discharge soft x-ray laser at shorter wavelength

Highly efficient and compact pulsed power supply system for a capillary discharge soft x-ray laser (SXRL) has been developed. The system consists of a 2.2 {mu}F two-stage LC inversion generator, a 2:54 step-up transformer, a 3 nF water capacitor, and a discharge section with a few tens of centimeter length capillary. Adoption of the pulsed transformer in combination with the LC inversion generator enables us to use only one gap switch in the circuit for charging the water capacitor up to about 0.5 MV. Furthermore, step-up ratio of a water capacitor voltage to a LC inversion generator initial charging voltage is about 40 with energy transfer efficiency of about 50%. It also leads to good reproducibility of a capillary discharge which is necessary for lasing a SXRL stably. For the study of the possibility of lasing a SXRL at shorter wavelength in a small laboratory scale, high-density and high-temperature plasma column suitable for the laser can be generated relatively easily with this system.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Plasma production by means of discharge in a spherical cavity

The work is devoted to the study of plasma, appearing as a result of cumulation of shock wave with form close to spherical. The shock wave was obtained by triggering of fast discharge (dI/dt about 10{sup 12} A/s) on inner surface of cavity, made from insulator. Spherical cavity with radius 4.5 mm was filled with Ar at 80 Pa. Inductive storage with semiconductive opening switch was used as a current driver. Spherical plasma with diameter about 1 mm, emitting in vacuum ultraviolet (vuv), was detected by means of pinhole measurements with time gated microchannel plate camera, starting about 50 ns from the beginning of the discharge. vuv spectra have shown the presence spectral lines of ArV-ArVIII ions, which gives the estimation of electron temperature as 30 eV. The plasma ball reveals no instabilities, keeps its characteristics and emits vuv radiation during 300 ns. After 600 ns from the beginning of the discharge plasma emits a flux of electrons with energies about 1 keV with temporal structure about 100 ns.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Compression and strong rarefaction in high power impulse magnetron sputtering discharges

Gas compression and strong rarefaction have been observed for high power impulse magnetron sputtering (HIPIMS) discharges using a copper target in argon. Time-resolved ion saturation currents of 35 probes were simultaneously recorded for HIPIMS discharges operating far above the self-sputtering runaway threshold. The argon background pressure was a parameter for the evaluation of the spatial and temporal development of the plasma density distribution. The data can be interpreted by a massive onset of the sputtering flux (sputter wind) that causes a transient densification of the gas, followed by rarefaction and the replacement of gas plasma by the metal plasma of sustained self-sputtering. The plasma density pulse follows closely the power pulse at low pressure. At high pressure, the relatively remote probes recorded a density peak only after the discharge pulse, indicative for slow, diffusive ion transport.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Micro Electro Discharge Machining of Electrically Nonconductive Ceramics

EDM is a known process for machining of hard and brittle materials. Due to its noncontact and nearly forceless behaviour, it has been introduced into micro manufacturing and through constant development it is now an important means for producing high-precision micro geometries. One restriction of EDM is its limitation to electrically conducting materials.Today many applications, especially in the biomedical field, make use of the benefits of ceramic materials, such as high strength, very low wear and biocompatibility. Common ceramic materials such as Zirconium dioxide are, due to their hardness in the sintered state, difficult to machine with conventional cutting techniques. A demand for the introduction of EDM to these materials could so far not be satisfied because of their nonconductive nature.At the Chemnitz University of Technology and the Fraunhofer IWU, investigations in the applicability of micro-EDM for the machining of nonconductive ceramics are being conducted. Tests are undertaken using micro-EDM drilling with Tungsten carbide tool electrodes and ZrO{sub 2} ceramic workpieces. A starting layer, in literature often referred to as 'assisting electrode' is used to set up a closed electric circuit to start the EDM process. Combining carbon hydride based dielectric and a specially designed low-frequency vibration setup to excite the workpiece, the process environment can be held within parameters to allow for a constant EDM process even after the starting layer is machined. In the experiments a cylindrical 120 {mu}m diameter Tungsten carbide tool electrode and Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} worpieces are used. The current and voltage signals of the discharges within the different stages of the process (machining of the starting layer, machining of the base material, transition stage) are recorded and their characteristics compared to discharges in metallic material. Additionally, the electrode feed is monitored. The influences of the process parameters are analysed with regard to the discharge type, electrode wear and process speed.Using the found parameters, micro geometries can be successfully machined into nonconductive Y{sub 2}O{sub 3}- and MgO- stabilized ZrO{sub 2} ceramic by means of micro-EDM.

36 MATERIALS SCIENCE↗

Study of Heating and Fusion Power Production in ITER Discharges

ITER simulations, in which the temperatures, toroidal angular frequency and currents are evolved, are carried out using the PTRANSP code starting with initial profiles and boundary conditions obtained from TSC code studies. The dependence of heat deposition and current drive on ICRF frequency, number of poloidal modes, beam orientation, number of Monte Carlo particles and ECRH launch angles is studied in order to examine various possibilities and contingencies for ITER steady state and hybrid discharges. For the hybrid discharges, the fusion power production and fusion Q, computed using the Multi-Mode MMM v7.1 anomalous transport model, are compared with those predicted using the GLF23 model. The simulations of the hybrid scenario indicate that the fusion power production at 1000 sec will be approximately 500 MW corresponding to a fusion Q = 10.0. The discharge scenarios simulated aid in understanding the conditions for optimizing fusion power production and in examining measures of plasma performance.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Spatiotemporal temperature and density characterization of high-power atmospheric flashover discharges over inert poly(methyl methacrylate) and energetic pentaerythritol tetranitrate dielectric surfaces

A flashover arc source that delivered up to 200 mJ on the 100s-of-ns time-scale to the arc and a user-selected dielectric surface was characterized for studying high-explosive kinetics under plasma conditions. The flashover was driven over thin pentaerythritol tetranitrate (PETN) and poly(methyl methacrylate) (PMMA) dielectric films and the resultant plasma was characterized in detail. Time- and space-resolved temperatures and electron densities of the plasma were obtained using atomic emission spectroscopy. The hydrodynamics of the plasma was captured through fast, visible imaging. Fourier transform infrared spectroscopy (FTIR) was used to characterize the films pre- and post-shot for any chemical alterations. Time-resolved infrared spectroscopy (TRIR) provided PETN depletion data during the plasma discharge. For both types of films, temperatures of 1.6-1.7 eV and electron densities of {approx}7-8 x 10{sup 17}/cm{sup 3}{approx}570 ns after the start of the discharge were observed with temperatures of 0.6-0.7 eV persisting out to 15 {mu}s. At 1.2 {mu}s, spatial characterization showed flat temperature and density profiles of 1.1-1.3 eV and 2-2.8 x 10{sup 17}/cm{sup 3} for PETN and PMMA films, respectively. Images of the plasma showed an expanding hot kernel starting from radii of {approx}0.2 mm at {approx}50 ns and reaching {approx}1.1 mm at {approx}600 ns. The thin films ablated or reacted several hundred nm of material in response to the discharge. First TRIR data showing the in situ reaction or depletion of PETN in response to the flashover arc were successfully obtained, and a 2-{mu}s, 1/e decay constant was measured. Preliminary 1 D simulations compared reasonably well with the experimentally determined plasma radii and temperatures. These results complete the first steps to resolving arc-driven PETN reaction pathways and their associated kinetic rates using in situ spectroscopy techniques.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Characteristics of argon plasma waveguide produced by alumina capillary discharge for short wavelength laser application

We have reported the argon (Ar) plasma waveguide produced in an alumina (Al{sub 2}O{sub 3}) capillary discharge and used to guide ultrashort laser pulses at intensities of the order of 10{sup 16} W/cm{sup 2}. The electron density in the plasma waveguide was measured to be 1x10{sup 18} cm{sup -3}, in agreement with one-dimensional magnetrohydrodynamic (MHD) simulations. The MHD code was also used to evaluate the degree of ionization of argon (Ar) in the preformed plasma waveguide. The maximum ion charge state of Ar{sup 3+} in capillary discharge was measured and obtained in the MHD simulations. The spectrum of the propagated laser pulse in the Ar plasma waveguide was not modified and was well reproduced by a particle-in-cell simulations under initial ion charge state of Ar{sup 3+} in the preformed plasma waveguide. The optimum timing for the laser pulse injection was around 150 ns after initiation of a discharge with a peak current of 200 A.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Treatment surfaces with atomic oxygen excited in dielectric barrier discharge plasma of O{sub 2} admixed to N{sub 2}

This paper describes the increase in surface energy of substrates by their treatment with gas composition generated in plasmas of DBD (Dielectric Barrier Discharge) in O2 admixed with N2. Operating gas dissociation and excitation was occurred in plasmas developed in two types of reactors of capacitively-coupled dielectric barrier configurations: coaxial cylindrical, and flat rectangular. The coaxial cylindrical type comprised an inner cylindrical electrode encapsulated in a ceramic sheath installed coaxially inside a cylindrical ceramic (quartz) tube passing through an annular outer electrode. Components of the flat rectangular type were a flat ceramic tube of a narrow rectangular cross section supplied with two flat electrodes mounted against one another outside of the long parallel walls of this tube. The operating gas, mixture of N{sub 2} and O{sub 2}, was flowing in a completely insulated discharge gap formed between insulated electrodes of the devices with an average velocity of gas inlet of about 7 to 9 m/s. Dielectric barrier discharge plasma was excited in the operating gaps with a bipolar pulse voltage of about 6 kV for 2 ms at 50 kHz repetition rate applied to the electrodes of the coaxial device, and of about 14 kV for 7 ms at 30 kHz repetition rate for the flat linear device. A lifetime of excited to the 2s{sup 2}2p{sup 4}({sup 1}S{sub 0}) state in DBD plasma and streaming to the surfaces with a gas flow atomic oxygen, responsible presumably for treating surfaces, exceeded 10 ms in certain cases, that simplified its separation from DBD plasma and delivery to substrates. As it was found in particular, surfaces of glass and some of polymers revealed significant enhancement in wettability after treatment.

36 MATERIALS SCIENCE↗

Nonmonotonic radial distribution of excited atoms in a positive column of pulsed direct currect discharges in helium

Nonmonotonic radial distributions of excited helium atoms have been experimentally observed in a positive column of pulsed helium discharges using planar laser induced fluorescence. Computational analysis of the discharge dynamics with a fluid plasma model confirms the experimental observations over a range of pressures and currents. The observed effect is attributed to the peculiarities of electron population-depopulation of the excited states during the 'dynamic discharge' conditions with strong modulations of the electric field maintaining the plasma.

74 ATOMIC AND MOLECULAR PHYSICS↗

Laser-heater assisted plasma channel formation in capillary discharge waveguides

A method of creating plasma channels with controllable depth and transverse profile for the guiding of short, high power laser pulses for efficient electron acceleration is proposed. The plasma channel produced by the hydrogen-filled capillary discharge waveguide is modified by a ns-scale laser pulse, which heats the electrons near the capillary axis. This interaction creates a deeper plasma channel within the capillary discharge that evolves on a ns-time scale, allowing laser beams with smaller spot sizes than would otherwise be possible in the unmodified capillary discharge.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

High-k shallow traps observed by charge pumping with varying discharging times

In this paper, we investigate the influence of falling time and base level time on high-k bulk shallow traps measured by charge pumping technique in n-channel metal-oxide-semiconductor field-effect transistors with HfO{sub 2}/metal gate stacks. N{sub T}-V{sub high} {sub level} characteristic curves with different duty ratios indicate that the electron detrapping time dominates the value of N{sub T} for extra contribution of I{sub cp} traps. N{sub T} is the number of traps, and I{sub cp} is charge pumping current. By fitting discharge formula at different temperatures, the results show that extra contribution of I{sub cp} traps at high voltage are in fact high-k bulk shallow traps. This is also verified through a comparison of different interlayer thicknesses and different Ti{sub x}N{sub 1−x} metal gate concentrations. Next, N{sub T}-V{sub high} {sub level} characteristic curves with different falling times (t{sub falling} {sub time}) and base level times (t{sub base} {sub level}) show that extra contribution of I{sub cp} traps decrease with an increase in t{sub falling} {sub time}. By fitting discharge formula for different t{sub falling} {sub time}, the results show that electrons trapped in high-k bulk shallow traps first discharge to the channel and then to source and drain during t{sub falling} {sub time}. This current cannot be measured by the charge pumping technique. Subsequent measurements of N{sub T} by charge pumping technique at t{sub base} {sub level} reveal a remainder of electrons trapped in high-k bulk shallow traps.

36 MATERIALS SCIENCE↗

Ignition and extinction phenomena in helium micro hollow cathode discharges

Micro hollow cathode discharges (MHCD) were produced using 250 μm thick dielectric layer of alumina sandwiched between two nickel electrodes of 8 μm thickness. A through cavity at the center of the chip was formed by laser drilling technique. MHCD with a diameter of few hundreds of micrometers allowed us to generate direct current discharges in helium at up to atmospheric pressure. A slowly varying ramped voltage generator was used to study the ignition and the extinction periods of the microdischarges. The analysis was performed by using electrical characterisation of the V-I behaviour and the measurement of He*({sup 3}S{sub 1}) metastable atoms density by tunable diode laser spectroscopy. At the ignition of the microdischarges, 2 μs long current peak as high as 24 mA was observed, sometimes followed by low amplitude damped oscillations. At helium pressure above 400 Torr, an oscillatory behaviour of the discharge current was observed just before the extinction of the microdischarges. The same type of instability in the extinction period at high pressure also appeared on the density of He*({sup 3}S{sub 1}) metastable atoms, but delayed by a few μs relative to the current oscillations. Metastable atoms thus cannot be at the origin of the generation of the observed instabilities.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The evidence of cathodic micro-discharges during plasma electrolytic oxidation process

Plasma electrolytic oxidation (PEO) processing of EV31 magnesium alloy has been carried out in fluoride containing electrolyte under bipolar pulse current regime. Unusual PEO cathodic micro-discharges have been observed and investigated. It is shown that the cathodic micro-discharges exhibit a collective intermittent behavior, which is discussed in terms of charge accumulations at the layer/electrolyte and layer/metal interfaces. Optical emission spectroscopy is used to determine the electron density (typ. 10{sup 15} cm{sup −3}) and the electron temperature (typ. 7500 K) while the role of F{sup −} anions on the appearance of cathodic micro-discharges is pointed out.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The channel radius and energy of cloud-to-ground lightning discharge plasma with multiple return strokes

Using the spectra of a cloud-to-ground (CG) lightning flash with multiple return strokes and combining with the synchronous radiated electrical field information, the linear charge density, the channel radius, the energy per unit length, the thermal energy, and the energy of dissociation and ionization in discharge channel are calculated with the aid of an electrodynamic model of lightning. The conclusion that the initial radius of discharge channel is determined by the duration of the discharge current is confirmed. Moreover, the correlativity of several parameters has been analyzed first. The results indicate that the total intensity of spectra is positive correlated to the channel initial radius. The ionization and thermal energies have a linear relationship, and the dissociation energy is correlated positively to the ionization and thermal energies, the energy per unit length is in direct proportion to the square of initial radius in different strokes of one CG lightning.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Characteristics of radio-frequency atmospheric pressure dielectric-barrier discharge with dielectric electrodes

An experimental investigation to characterize the properties and highlight the benefits of atmospheric pressure radio-frequency dielectric-barrier discharge (rf DBD) with dielectric electrodes fabricated by anodizing aluminium substrate is presented. The current-voltage characteristics and millisecond images are used to distinguish the α and γ modes. This atmospheric rf DBD is observed to retain the discharge volume without constriction in γ mode. Optical emission spectroscopy demonstrates that the large discharge current leads to more abundant reactive species in this plasma source.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Lowering of the firing voltage and reducing of the discharge delay time in alternating current plasma display panels by a discontinuous spin-coated LaB{sub 6} film on the MgO protective layer

A spin coated LaB{sub 6} discontinuous film is covered on MgO protective layer to improve the discharge performance of alternating current plasma display panels. Under the premise of high transmittance of more than 90%, a very small amount of polycrystal LaB{sub 6} powders added in an organic solvent are chosen as the coating solution. The discharge characteristics results show that with 250 torr 5% Xe-Ne pressure, the firing voltage and discharge delay time of the test panel with LaB{sub 6}/MgO double protective layer are decreased by 13.4% and 36.5%, respectively, compared with that of conventional MgO protective layer, likely owing to the low work function of LaB{sub 6.} Furthermore, the aging time of the proposed structure is comparable to that of pure MgO protective layer. Therefore, it will not increase the production costs and is highly suitable to be applied for alternating current plasma display panels with low electrical power consumption.

36 MATERIALS SCIENCE↗