Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BASE PRESSURE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54

Research study of pressure instrumentation

To obtain a more vibration resistant pressure sensor for use on the Space Shuttle Main Engine, a proximity probe based, diaphragm type pressure sensor breadboard was developed. A fiber optic proximity probe was selected as the sensor. In combination with existing electronics, a thermal stability evaluation of the entire probe system was made. Based upon the results, a breadboard design of the pressure sensor and electronics was made and fabricated. A brief series of functional experiments was made with the breadboard to calibrate, thermally compensate, and linearize its response. In these experiments, the performance obtained in the temperature range of -320 F (liquid N2) to +200 F was comparable to that of the strain gage based sensor presently in use on the engine. In tests at NASA-Marshall Space Flight Center (MSFC), after some time at or near liquid nitrogen temperatures, the sensor output varied over the entire output range. These large spurious signals were attributed to condensation of air in the sensing gap. In the next phase of development of this sensor, an evaluation of fabrication techniques toward greater thermal and mechanical stability of the fiber probe assembly must be made. In addition to this, a positive optics to metal seal must be developed to withstand the pressure that would result from a diaphragm failure.

Hoogenboom, L.↗

The Behavior of IAPWS-95 from 250 to 300 K and Pressures up to 400 MPa: Evaluation Based on Recently Derived Property Data

Over the past several years, considerable scientific and technical interest has been focused on accurate thermodynamic properties of fluid water covering part of the subcooled (metastable) region and the stable liquid from the melting line up to about 300 K and pressures up to several hundred MPa. Between 2000 and 2010, experimental density data were published whose accuracy was not completely clear. The scientific standard equation of state for fluid water, the IAPWS-95 formulation, was developed on the basis of experimental data for thermodynamic properties that were available by 1995. In this work, it is examined how IAPWS-95 behaves with respect to the experimental data published after 1995. This investigation is carried out for temperatures from 250 to 300 K and pressures up to 400 MPa. The starting point is the assessment of the current data situation. This was mainly performed on the basis of data for the density, expansivity, compressibility, and isobaric heat capacity, which were derived in 2015 from very accurate speed-of-sound data. Apart from experimental data and these derived data, property values calculated from the recently published equation of state for this region of Holten et al. (2014) were also used. As a result, the unclear data situation could be clarified, and uncertainty values could be estimated for the investigated properties. In the region described above, detailed comparisons show that IAPWS-95 is able to represent the latest experimental data for the density, expansivity, compressibility, speed of sound, and isobaric heat capacity to within the uncertainties given in the release on IAPWS-95. Since the release does not contain uncertainty estimates for expansivities and compressibilities, the statement relates to the error propagation of the given uncertainty in density. Due to the lack of experimental data for the isobaric heat capacity for pressures above 100 MPa, no uncertainty estimates are given in the release for this pressure range. Results of the investigation of IAPWS-95 concerning its behavior with regard to the isobaric heat capacity in the high-pressure low-temperature region are also presented. Comparisons with very accurate speed-of-sound data published in 2012 showed that the uncertainty estimates of IAPWS-95 in speed of sound could be decreased for temperatures from 283 to 473 K and pressures up to 400 MPa.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Hydrostatic pressure effect on the Co-based honeycomb magnet BaCo 2 (AsO 4 ) 2

Here the honeycomb antiferromagnet BaCo 2 (AsO 4 ) 2 , in which small in-plane magnetic fields (H1 ≈ 0.26T and H2 ≈ 0.52T at T = 1.8 K < T N ≈ 5.4K) induce two magnetic phase transitions, has attracted attention as a possible candidate material for the realization of Kitaev physics based on the 3d element Co 2+ . Here, we report on the change in the transition temperature T N and the critical fields H1 and H2 of BaCo 2 (AsO 4 ) 2 with hydrostatic pressure up to ~20 kbar, as determined from magnetization and specific heat measurements. Within this pressure range, a marginal increase in the magnetic ordering temperature is observed. At the same time, the critical fields are changed significantly (up to ~25 –35%). Specifically, we find that H1 is increased with hydrostatic pressure, i.e., the antiferromagnetic state is stabilized, whereas H2, which was previously associated with a transition into a proposed Kitaev spin-liquid state, decreases with increasing pressure. We discuss to what extent these results are compatible with suggested models with sizable third-nearest-neighbor exchange. Overall, the results put constraints on the magnetic models that are used to describe the low-temperature magnetic properties of BaCo 2 (AsO 4 ) 2 .

2-dimensional systems↗

High-pressure effects on nonfluorinated BiS 2 -based superconductors La 1 – x M x OBiS 2 ( M = Ti and Th)

Layered LnOBiS 2 (where Ln represents a lanthanide element) compounds with Ln = La, Ce, Pr, Nd, and Yb can be rendered conducting and superconducting via two routes, substitution of F for O or the tetravalent ions Ti, Zr, Hf, and Th for trivalent Ln ions. Electrical resistivity measurements on nonfluorinated La 0.80 Ti 0.20 OBiS 2 and La 0.85 Th 0.15 OBiS 2 superconductors were performed between ~1.5 and 300 K and under pressure up to 2.4 GPa. For both compounds, the superconducting transition temperature T c , which is ~2.9K at ambient pressure, gradually increases with pressure to 3.2–3.7 K at ~1GPa, above which it is suppressed and the superconducting transitions become very broad. Measurements of the normal-state electrical resistivity of the two compounds reveal discontinuous changes in the resistivity as a function of pressure at ~0.6GPa. Surprisingly, above 1.3 GPa, semiconductinglike behavior reappears in La 0.80 Ti 0.20 OBiS 2 . This paper reveals a new high-pressure phase of La 1-x M x OBiS 2 containing the tetravalent ions M=Ti, Th which does not favor superconductivity. In contrast, application of pressure to fluorinated LaO 0.5 F 0.5 BiS 2 produces an abrupt tetragonal-monoclinic transition to a metallic phase with an enhanced T c . Here, these results demonstrate that the response of the normal and superconducting properties of LaOBiS 2 -based compounds depends strongly on the atomic site where the electron donor ions are substituted.

36 MATERIALS SCIENCE↗

Generation of shock trains in free liquid jets with a nanosecond green laser

Shock wave trains in liquid jets were previously generated only by ablation with femtosecond x-ray lasers. Here we show that shock trains in water microjets can be also generated using nanosecond green laser pulses with 1- to 10-mJ energy. Furthermore, the ablation of 15-, 20-, 30-, and 70-μm water microjets opened a gap in the jets and launched an initial shock wave. Fully developed shock trains were observed in the 30- and 70-μm jets up to 250-ns delays, and these trains were also transmitted inside the nozzles. A few tens of nanoseconds after the pulse, the shock dynamics and its pressure became similar to the ones generated by x-ray lasers, with a more rapid pressure decay in thinner jets. At time delays exceeding 100 ns in the 30-μm jets, the leading shock pressure stabilized to an approximately constant pressure of 40 MPa. The energy density deposited in the jets was estimated at 30 MJ/cm 3 by comparing the jet gaps in the green and x-ray laser experiments, and matched previous estimates for optical ablation in water. Here, the pressure decay in the 30-μm jets was modeled based on the pressure decay observed in x-ray laser experiments.

74 ATOMIC AND MOLECULAR PHYSICS↗

Version pressure feedback mechanisms for speculative versioning caches

Mechanisms are provided for controlling version pressure on a speculative versioning cache. Raw version pressure data is collected based on one or more threads accessing cache lines of the speculative versioning cache. One or more statistical measures of version pressure are generated based on the collected raw version pressure data. A determination is made as to whether one or more modifications to an operation of a data processing system are to be performed based on the one or more statistical measures of version pressure, the one or more modifications affecting version pressure exerted on the speculative versioning cache. An operation of the data processing system is modified based on the one or more determined modifications, in response to a determination that one or more modifications to the operation of the data processing system are to be performed, to affect the version pressure exerted on the speculative versioning cache.

97 MATHEMATICS AND COMPUTING↗

Calculations of separated 3-D flows with a pressure-staggered Navier-Stokes equations solver

A Navier-Stokes equations solver based on a pressure correction method with a pressure-staggered mesh and calculations of separated three-dimensional flows are presented. It is shown that the velocity pressure decoupling, which occurs when various pressure correction algorithms are used for pressure-staggered meshes, is caused by the ill-conditioned discrete pressure correction equation. The use of a partial differential equation for the incremental pressure eliminates the velocity pressure decoupling mechanism by itself and yields accurate numerical results. Example flows considered are a three-dimensional lid driven cavity flow and a laminar flow through a 90 degree bend square duct. For the lid driven cavity flow, the present numerical results compare more favorably with the measured data than those obtained using a formally third order accurate quadratic upwind interpolation scheme. For the curved duct flow, the present numerical method yields a grid independent solution with a very small number of grid points. The calculated velocity profiles are in good agreement with the measured data.

Kim, S.-W.↗

Calculations of separated 3-D flows with a pressure-staggered Navier-Stokes equations solver

A Navier-Stokes equations solver based on a pressure correction method with a pressure-staggered mesh and calculations of separated three-dimensional flows are presented. It is shown that the velocity pressure decoupling, which occurs when various pressure correction algorithms are used for pressure-staggered meshes, is caused by the ill-conditioned discrete pressure correction equation. The use of a partial differential equation for the incremental pressure eliminates the velocity pressure decoupling mechanism by itself and yields accurate numerical results. Example flows considered are a three-dimensional lid driven cavity flow and a laminar flow through a 90 degree bend square duct. For the lid driven cavity flow, the present numerical results compare more favorably with the measured data than those obtained using a formally third order accurate quadratic upwind interpolation scheme. For the curved duct flow, the present numerical method yields a grid independent solution with a very small number of grid points. The calculated velocity profiles are in good agreement with the measured data.

Kim, S.-W.↗

Airborne and ground based lidar measurements of the atmospheric pressure profile

The first high accuracy remote measurements of the atmospheric pressure profile have been made. The measurements were made with a differential absorption lidar system that utilizes tunable alexandrite lasers. The absorption in the trough between two lines in the oxygen A-band near 760 nm was used for probing the atmosphere. Measurements of the two-dimensional structure of the pressure field were made in the troposphere from an aircraft looking down. Also, measurements of the one-dimensional structure were made from the ground looking up. Typical pressure accuracies for the aircraft measurements were 1.5-2 mbar with a 30-m vertical resolution and a 100-shot average (20 s), which corresponds to a 2-km horizontal resolution. Typical accuracies for the upward viewing ground based measurements were 2.0 mbar for a 30-m resolution and a 100-shot average.

Korb, C. Laurence↗

Atmospheric Pressure Chemical Vapor Deposition of High Silica SiO 2 -TiO 2 Antireflective Thin Films for Glass Based Solar Panels

The atmospheric pressure chemical vapor deposition (APCVD) of SiO 2 -TiO 2 thin films employing [[(tBuO) 3 Si] 2 O-Ti(OiPr) 2 ], which can be prepared from commercially available materials, results in antireflective thin films on float glass under industrially relevant manufacturing conditions. It was found that while the deposition temperature had an effect on the SiO 2 :TiO 2 ratio, the thickness was dependent on the time of deposition. This study shows that it is possible to use APCVD employing a single source precursor containing titanium and silicon to produce thin films on float glass with high SiO 2 :TiO 2 ratios.

36 MATERIALS SCIENCE↗

On the Power Factor of Bismuth-Telluride-Based Alloys near Topological Phase Transitions at High Pressures

The Seebeck coefficient S and electrical conductivity σ of bismuth-telluride-based alloys with substituents in the Bi and Te sublattices are studied at pressures up to 12 GPa at room temperature. It is shown that the electrical conductivity increases with pressure and, despite a decrease in the Seebeck coefficient, the power factor S{sup 2}σ increases in p-Bi{sub 0.5}Sb{sub 1.5}Te{sub 3} and n-Bi{sub 2}Te{sub 1.65}Se{sub 0.65}S{sub 0.7} alloys. A maximum increase in the power factor is observed for n-Bi{sub 2}Te{sub 1.65}Se{sub 0.65}S{sub 0.7} in the pressure range of 3–4 GPa corresponding to the electronic topological phase transition. The studied alloys are used in modeling the thermoelectric module with adjustable mechanical stress applied to thermoelements.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Atmospheric pressure plasma jet with high-voltage power supply based on piezoelectric transformer

The dielectric barrier discharge plasma jet, an example of the nonthermal atmospheric pressure plasma jet (APPJ), generates low-temperature plasmas that are suitable for the atomization of volatile species and can also be served as an ionization source for ambient mass and ion mobility spectrometry. A new design of APPJ for mass spectrometry has been built in our group. In these plasma sources magnetic transformers (MTs) and inductors are typically used in power supplies but they present several drawbacks that are even more evident when dealing with high-voltage normally used in APPJs. To overcome these disadvantages, high frequency generators with the absence of MT are proposed in the literature. However, in the case of miniaturized APPJs these conventional power converters, built of ferromagnetic cores and inductors or by means of LC resonant tank circuits, are not so useful as piezoelectric transformer (PT) based power converters due to bulky components and small efficiency. We made and examined a novel atmospheric pressure plasma jet with PT supplier served as ionization source for ambient mass spectrometry, and especially mobile spectrometry where miniaturization, integration of components, and clean plasma are required. The objective of this paper is to describe the concept, design, and implementation of this miniaturized piezoelectric transformer-based atmospheric pressure plasma jet.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Base Heating Sensitivity Study for a 4-Cluster Rocket Motor Configuration in Supersonic Freestream

In support of launch vehicle base heating and pressure prediction efforts using the Loci-CHEM Navier-Stokes computational fluid dynamics solver, 35 numerical simulations of the NASA TND-1093 wind tunnel test have been modeled and analyzed. This test article is composed of four JP-4/LOX 500 lbf rocket motors exhausting into a Mach 2 - 3.5 wind tunnel at various ambient pressure conditions. These water-cooled motors are attached to a base plate of a standard missile forebody. We explore the base heating profiles for fully coupled finite-rate chemistry simulations, one-way coupled RAMP (Reacting And Multiphase Program using Method of Characteristics)-BLIMPJ (Boundary Layer Integral Matrix Program - Jet Version) derived solutions and variable and constant specific heat ratio frozen flow simulations. Variations in turbulence models, temperature boundary conditions and thermodynamic properties of the plume have been investigated at two ambient pressure conditions: 255 lb/sq ft (simulated low altitude) and 35 lb/sq ft (simulated high altitude). It is observed that the convective base heat flux and base temperature are most sensitive to the nozzle inner wall thermal boundary layer profile which is dependent on the wall temperature, boundary layer s specific energy and chemical reactions. Recovery shock dynamics and afterburning significantly influences convective base heating. Turbulence models and external nozzle wall thermal boundary layer profiles show less sensitivity to base heating characteristics. Base heating rates are validated for the highest fidelity solutions which show an agreement within +/-10% with respect to test data.

Mehta, Manish↗

Oxidation of alloys for energy applications in supercritical CO 2 and H 2 O

To facilitate development of supercritical CO 2 (sCO 2 ) power plants, a comparison of the oxidation behavior of austenitic stainless steels and Ni-base alloys in sH 2 O and sCO 2 were made. Experiments were conducted at 730 °C/207 bar (sCO 2 ) and 726 °C/208 bar (sH 2 O). Ni-base alloys in sCO 2 did not exhibit much change with pressure. Ni-base alloys in sH 2 O had an increase in corrosion rate and the log of the parabolic rate constant was proportional to pressure. Lastly, fine-grain austenitic stainless steels in sCO 2 and sH 2 O were both less protective with pressure as the dense protective chromia scale was replaced with faster growing Fe-oxide rich scales.

36 MATERIALS SCIENCE↗

Outer atmospheres of cool stars. VI - Models for Epsilon Eridani based on IUE spectra of C II, Mg II, Si II, and Si III

Observations of the ultraviolet line spectrum of the active chromosphere star, Epsilon Eridani, obtained with the IUE satellite have been analyzed. The coupled statistical equilibrium and radiative transfer equations for the prominent transitions of C II, Mg II, Si II, and Si III. A satisfactory fit to all of the line strengths can be achieved with a model similar to that recently proposed to explain bright points on the quiet sun. A surface pressure at the base of the transition region of 0.5 dynes/sq cm is derived, which is a factor of 3 higher than the quiet sun value, but a factor of 3 smaller than predicted by scaling laws, assuming a conductively heated stellar transition region. It is found that the surface fluxes of the C II 1334, 1335 and Si III 1892 emission lines are good diagnostics of pressure at the base of the transition region, but line ratio techniques using the 1892 line for estimating electron densities may be valid.

Simon, T.↗

A fluid model for the edge pressure pedestal height and width in tokamaks based on the transport constraint of particle, energy, and momentum balance

A fluid model for the tokamak edge pressure profile required by the conservation of particles, momentum and energy in the presence of specified heating and fueling sources and electromagnetic and geometric parameters has been developed. Kinetics effects of ion orbit loss are incorporated into the model. The use of this model as a “transport” constraint together with a “Peeling-Ballooning (P-B)” instability constraint to achieve a prediction of edge pressure pedestal heights and widths in future tokamaks is discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a high temperature capacitive pressure transducer

High temperature pressure transducers capable of continuous operation while exposed to 650 C were developed and evaluated over a full-scale differential pressure range of + or - 69 kPa. The design of the pressure transducers was based on the use of a diaphragm to respond to pressure, variable capacitive elements arranged to operate as a differential capacitor to measure diaphragm response and on the use of fused silica for the diaphragm and its supporting assembly. The uncertainty associated with measuring + or - 69 kPa pressures between 20C and 650C was less than + or - 6%.

Egger, R. L.↗