Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 973 records · Page 54
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Automated synthesis of transonic transports.

The development of a vehicle synthesis program, called TRANSYN, designed to perform automated preliminary design of long-haul transport aircraft is briefly described. The TRANSYN-TST program was used in a study of commercial transonic transports designed for introduction in the early 1980s. The optimum engine cycles of all the study aircraft are within the current state-of-the-art, but fan noise suppression will be required to meet the noise requirements of FAR Part 36. It was found that full use of advanced composite materials in the wing and fuselage structure is neutrally cost effective when compared with aluminum for aircraft designed to cruise in the low transonic regime (Mach 0.90 to 1.0), but that such materials are very cost effective for aircraft designed to cruise in the high transonic regime (Mach 1.0 to 1.15). Finally, increasing speed results in reduced trip times with at most very slight increases in cost in the low transonic regime, but cruise speeds in the high transonic regime result in a significant economic penalty for the conventional configurations considered in this study.

Ardema, M. D.↗
NASA NTRS1973

Large boron--epoxy filament-wound pressure vessels

Advanced composite material used to fabricate pressure vessel is prepeg (partially cured) consisting of continuous, parallel boron filaments in epoxy resin matrix arranged to form tape. To fabricate chamber, tape is wound on form which must be removable after composite has been cured. Configuration of boron--epoxy composite pressure vessel was determined by computer program.

Jensen, W. M.↗
NASA NTRS1972

Development and fabrication of a graphite polyimide box beam

The state-of-the-art of graphite/polyimide structures was evaluated and key design and fabrication issues to be considered in future hardware programs are defined. The fabrication and testing at 500 F of a graphite/polyimide center wing box beam using OV-10A aircraft criteria was accomplished. The baseline design of this box was developed in a series of studies of other advanced composite materials: glass/epoxy, boron/epoxy, and boron/polyimide. The use of this basic design permits ready comparison of the performance of graphite/polyimide with these materials. Modifications to the baseline composite design were made only in those areas effected by the change of materials. Processing studies of graphite fiber polyimide resins systems resulted in the selection of a Modmor II/Gemon L material.

Nadler, M. A.↗
NASA NTRS1973

Inorganic separator technology program

Testing and failure analyses of silver zinc cells with largely inorganic separators were performed. The results showed that the wet stand and cycle life objective of the silver-zinc cell development program were essentially accomplished and led to recommendations for cell composition, design, and operation that should yield further improvement in wet and cycle life. A series of advanced inorganic materials was successfully developed and formulated into rigid and semiflexible separator samples. Suitable screening tests for evaluation of largely inorganic separators were selected and modified for application to the separator materials. The results showed that many of these formulations are potentially superior to previously used materials and permitted selection of three promising materials for further evaluation in silver-zinc cells.

Smatko, J. S.↗
NASA NTRS1973

Development of advanced composite rocket motor chambers using boron and graphite fibers.

Four 71-cm-diameter rocket motor chambers were designed and fabricated with advanced composite materials. The first three chambers were filament wound from boron/epoxy tape, and the fourth from graphite/epoxy tape. The first boron/epoxy chamber was 74 cm in length and was successfully hydroburst tested. The other three chambers were 57.6 cm in length for a smaller propellant load. The first shortened boron/epoxy chamber failed in proof test as a result of fabrication deficiencies. The last boron/epoxy and the graphite/epoxy chambers were successfully proof tested.

Jensen, W. M.↗
NASA NTRS1974

A nickel base alloy, NASA WAZ-16, with potential for gas turbine stator vane application

A nickel-base superalloy based on the nickel-aluminum-tungsten system designated WAZ-16 was developed for high strength in the 1095 C (2000 F) to 1205 C (2200 F) range. Its tensile strength at the latter temperature is approximately 186 MN/m2 (27,000 psi). The combination of properties of the alloy suggest that it has potential as a stator vane material in advanced gas turbine engines.

Waters, W. J.↗
NASA NTRS1972

Residual thermal stress control in composite reinforced metal structures

Advanced composite materials, composed of boron or graphite fibers and a supporting matrix, make significant structural efficiency improvements available to aircraft and aerospace designers. Residual stress induced during bonding of composite reinforcement to metal structural elements can be reduced or eliminated through suitable modification to the manufacturing processes. The most successful method employed during this program used a steel tool capable of mechanically loading the metal component in compression prior to the adhesive bonding cycle. Compression loading combined with heating to 350 F during the bond cycle can result in creep deformation in aluminum components. The magnitude of the deformation increases with increasing stress level during exposure to 350 F.

Kelly, J. B.↗
NASA NTRS1972

The bi-composite transition joint

The application of advanced composite materials to high performance structure frequently results in the desire to fabricate a structure from more than one composite system in order to tailor the composite material capabilities to the design requirements. The bi-composite transition provides a means of joining two different composite structural systems without the weight and complexity of mechanical attachments. The monolayer plies or combinations of plies of one composite system are interleaved with and bonded to the plies of the adjacent composite system, thereby providing a direct load transfer between the two composite structures.

Dullea, K. C., Jr.↗
NASA NTRS1974

Application of advanced composites to helicopter airframe structures

The present work outlines a study whose objective was to assess the possible use of advanced composite materials to helicopter fuselage structure. The study used the CH-53D as a baseline design for comparison of composite with current conventional construction. Boron/epoxy and graphite/epoxy appeared to be the prime candidate materials for the major portion of the primary structure, while Kevlar-49/epoxy was the prime candidate material for secondary structure. A single-laminate shear-carrying skin combined with stringers and frames in an all-molded construction was considered the most promising concept for the airframe shell construction; foam-stabilized graphite/epoxy stringer was considered the prime concept for stringer construction. Shell construction and assembly concepts are discussed, and comparison of weight and material between current CH-53D airframe and the composite airframe shows that the latter may represent an 18% weight saving. Based on a fleet requirement of 600 vehicles, the operating cost for a fleet of helicopters constructed with the composite material airframe flying 500 hours a year per aircraft over a ten-year service life was calculated, indicating a $337,000 saving per helicopter.

Rich, M. J.↗
NASA NTRS1975

Composite lattice structure

A lattice type structural panel concept which exploits the unidirectional character of filamentary advanced composite materials was described. This lattice has potential for applications where stiff lightweight structures are needed such as large area panels for space satellites. Formulae are presented to calculate the panel weight and plate bending stiffness. This analysis indicates that structures with significantly lighter weight than conventional minimum gauge sandwich construction can be fabricated. A suggested fabrication procedure is also presented along with photographs of some typical panels.

Rhodes, M. D.↗
NASA NTRS1975

Preliminary thermal-structural design and analysis of an airframe-integrated hydrogen-cooled scramjet

This paper presents the salient features of a preliminary thermal-structural design and analysis study of a hydrogen-fueled, regeneratively cooled, airframe-integrated scramjet. This three-dimensional fixed geometry scramjet concept which was developed at NASA Langley Research Center is designed to operate over a flight Mach number range from 4 to 10. The thermal-structural study was focused on a scramjet application to one concept for a hypersonic research vehicle and was based on technology developed under the NASA Hypersonic Research Engine Project. State-of-the-art analytical methods consisting of lumped system and finite difference steady-state thermal analyses and a finite element structural analysis were used. The results of the study indicated that this scramjet concept is viable from both a structural mass and cooling requirement standpoint. However, advances in material and fabrication technology for hydrogen-cooled structures appear necessary for acceptable engine life for commercial application.

Wieting, A. R.↗
NASA NTRS1975

Development of an advanced spacecraft water and waste materials processing system

An Integrated Waste Management-Water System (WM-WS) which uses radioisotopes for thermal energy is described and results of its trial in a 4-man, 180 day simulated space mission are presented. It collects urine, feces, trash, and wash water in zero gravity, processes the wastes to a common evaporator, distills and catalytically purifies the water, and separates and incinerates the solid residues using little oxygen and no chemical additives or expendable filters. Technical details on all subsystems are given along with performance specifications. Data on recovered water and heat loss obtained in test trials are presented. The closed loop incinerator and other projects underway to increase system efficiency and capacity are discussed.

Murray, R. W.↗
NASA NTRS1974

Advanced composite structures

A monograph is presented which establishes structural design criteria and recommends practices to ensure the design of sound composite structures, including composite-reinforced metal structures. (It does not discuss design criteria for fiber-glass composites and such advanced composite materials as beryllium wire or sapphire whiskers in a matrix material.) Although the criteria were developed for aircraft applications, they are general enough to be applicable to space vehicles and missiles as well. The monograph covers four broad areas: (1) materials, (2) design, (3) fracture control, and (4) design verification. The materials portion deals with such subjects as material system design, material design levels, and material characterization. The design portion includes panel, shell, and joint design, applied loads, internal loads, design factors, reliability, and maintainability. Fracture control includes such items as stress concentrations, service-life philosophy, and the management plan for control of fracture-related aspects of structural design using composite materials. Design verification discusses ways to prove flightworthiness.

Source record↗
NASA NTRS1975

Optimization of an oxide dispersion strengthened Ni-Cr-Al alloy for gas turbine engine vanes

The investigation was carried out to determine the optimum alloy within the Ni-16Cr-Al-Y2O3 system for use as a vane material in advanced aircraft gas turbine engines. Six alloys containing nominally 4%, 5% and 6% Al with Y2O3 levels of 0.8% and 1.2% were prepared by mechanical attrition. Six small-scale, rectangular extrusions were produced from each powder lot for property evaluation. The approximate temperatures for incipient melting were found to be 1658 K (2525 F), 1644 K (2500 F) and 1630 K (2475 F) for the 4%, 5% and 6% aluminum levels, respectively. With the exception of longitudinal crystallographic texture, the eight extrusions selected for extensive evaluation either exceeded or were close to mechanical property goals. Major differences between the alloys became apparent during dynamic oxidation testing, and in particular during the 1366 K (2000 F)/500 hour Mach 1 tests carried out by NASA-Lewis. An aluminum level of 4.75% was subsequently judged to be optimum based on considerations of dynamic oxidation resistance, susceptibility to thermal fatigue cracking and melting point.

Klarstrom, D. L.↗
NASA NTRS1976

Technical and Economic Assessment of Span-Loaded Cargo Aircraft Concepts

The benefits are assessed of span distributed loading concepts as applied to future commercial air cargo operations. A two phased program is used to perform this assessment. The first phase consists of selected parametric studies to define significant configuration, performance, and economic trends. The second phase consists of more detailed engineering design, analysis, and economic evaluations to define the technical and economic feasibility of a selected spanloader design. A conventional all-cargo aircraft of comparable technology and size is used as a comparator system. The technical feasibility is demonstrated of the spanloader concept with no new major technology efforts required to implement the system. However, certain high pay-off technologies such as winglets, airfoil design, and advanced structural materials and manufacturing techniques need refinement and definition prior to application. In addition, further structural design analysis could establish the techniques and criteria necessary to fully capitalize upon the high degree of structural commonality and simplicity inherent in the spanloader concept.

Source record↗
NASA NTRS1976

Concepts for improving turbine disk integrity

Advanced disk structural concepts are used to improve the cyclic lives and reliability of turbine disks. Analytical studies were conducted to evaluate bore-entry disks as potential replacements for the existing first-stage turbine disks in the CF6-50 and JT8D-17 engines. Results of low-cycle fatigue, burst, fracture mechanics, and fragment energy analyses are summarized for the advanced disk designs and the existing disk designs with both conventional and advanced disk materials. Other disk concepts such as composite, laminated, link, multibore, multidisk, and spline disks were also evaluated for the CF6-50 engine.

Kaufman, A.↗
NASA NTRS1977

Nickel base alloy

A nickel base superalloy for use at temperatures of 2000 F (1095 C) to 2200 F (1205 C) was developed for use as stator vane material in advanced gas turbine engines. The alloy has a nominal composition in weight percent of 16 tungsten, 7 aluminum, 1 molybdenum, 2 columbium, 0.3 zirconium, 0.2 carbon and the balance nickel.

Freche, J. C.↗