Results for “Accelerator Applications” — Page 54

NASA NTRS1995

Energy measurement of electron beams by Compton scattering

A method has been proposed to utilize the well-known Compton scattering process as a tool to measure the centroid energy of a high energy electron beam at the 0.01% level. It is suggested to use the Compton scattering of an infrared laser off the electron beam, and then to measure the energy of the scattered gamma-rays very precisely using solid-state detectors. The technique proposed is applicable for electron beams with energies from 200 MeV to 16 GeV using presently available lasers. This technique was judged to be the most viable of all those proposed for beam energy measurements at the nearby Continuous Electron Beam Accelerator Facility (CEBAF). Plans for a prototype test of the technique are underway, where the main issues are the possible photon backgrounds associated with an electron accelerator and the electron and laser beam stabilities and diagnostics. The bulk of my ASEE summer research has been spent utilizing the expertise of the staff at the Aerospace Electronics Systems Division at LaRC to assist in the design of the test. Investigations were made regarding window and mirror transmission and radiation damage issues, remote movement of elements in ultra-high vacuum conditions, etc. The prototype test of the proposed laser backscattering method is planned for this December.

Keppel, Cynthia↗

NASA NTRS2006

A Quick Method for Estimating Vehicle Characteristics Appropriate for Continuous Thrust Round Trip Missions Within the Solar System

A simple method of estimating vehicle parameters appropriate for interplanetary travel can provide a useful tool for evaluating the suitability of particular propulsion systems to various space missions. Although detailed mission analyses for interplanetary travel can be quite complex, it is possible to derive hirly simple correlations which will provide reasonable trip time estimates to the planets. In the present work, it is assumed that a constant thrust propulsion system propels a spacecraft on a round trip mission having equidistant outbound and inbound legs in which the spacecraft accelerates during the first portion of each leg of the journey and decelerates during the last portion of each leg of the journey. Comparisons are made with numerical calculations from low thrust trajectory codes to estimate the range of applicability of the simplified correlations.

Emrich, Bill↗

NASA NTRS2009

T-Rex: A Japanese Space Tether Experiment

Electrodynamic tether (EDT) thrusters work by virtue of the force a magnetic field exerts on a wire carrying an electrical current. The force, which acts on any charged particle moving through a magnetic field (including the electrons moving in a current-carrying wire), were concisely expressed by Lorentz in 1895 in an equation that now bears his name. The force acts in a direction perpendicular to both the direction of current flow and the magnetic field vector. Electric motors make use of this force: a wire loop in a magnetic field is made to rotate by the torque the Lorentz Force exerts on it due to an alternating current in the loop times so as to keep the torque acting in the same sense. The motion of the loop is transmitted to a shaft, thus providing work. Although the working principle of EDT thrusters is not new, its application to space transportation may be significant. In essence, an EDT thruster is just a clever way of getting an electrical current to flow in a long orbiting wire (the tether) so that the Earth s magnetic field will accelerate the wire and, consequently the payload attached to the wire. The direction of current flow in the tether, either toward or away from the Earth along the local vertical, determines whether the magnetic force will raise or lower the orbit. The bias voltage of a vertically deployed metal tether, which results just from its orbital motion (assumed eastward) through Earth s magnetic field, is positive with respect to the ambient plasma at the top and negative at the bottom. This polarization is due to the action of the Lorentz force on the electrons in the tether. Thus, the natural current flow is the result of negative electrons being attracted to the upper end and then returned to the plasma at the lower end. The magnetic force in this case has a component opposite to the direction of motion, and thus leads to a lowering of the orbit and eventually to re-entry. In this generator mode of operation the Lorentz Force serves both to drive the current and then to act on the current to decelerate the system. One of the most important features of tether thrusters is that they use renewable energy sources to drive the electrical current flow in either the orbit-raising or orbit-lowering modes. Sources inherent to Earth orbit are used. To raise the orbit, sunlight can be converted to the electrical energy required to drive the tether current. To lower the orbit, the orbital energy itself (supplied by the Earth-to-orbit launcher when it raises the system into orbit) is the energy source of the tether current via the action of the Lorentz Force. Electrodynamic tethers can be directly applied to a wide spectrum of uses in space. As a propulsion system, they include satellite de-orbit, transfer of a satellite from one orbit to another, altitude maintenance for large spacecraft such as the International Space Station, and since it works wherever there is a magnetic field and an ionosphere planetary exploration missions. An electrodynamic tether upper stage could be used as an Orbit Transfer Vehicle (OTV) to move payloads within low earth orbit. The OTV would rendezvous with the payload and launch vehicle, grapple the payload and maneuver it to a new orbital altitude or inclination without the use of boost propellant. The tug could then lower its orbit to rendezvous with the next payload and repeat the process. Conceivably, such a system could perform several orbital maneuvering assignments without resupply, making it relatively inexpensive to operate.

Johnson, Les↗

NASA NTRS2010

Radiation Beamline Testbeds for the Simulation of Planetary and Spacecraft Environments for Human and Robotic Mission Risk Assessment

The Center for Radiation Engineering and Science for Space Exploration (CRESSE) at Prairie View A&M University, Prairie View, Texas, USA, is establishing an integrated, multi-disciplinary research program on the scientific and engineering challenges faced by NASA and the international space community caused by space radiation. CRESSE focuses on space radiation research directly applicable to astronaut health and safety during future long term, deep space missions, including Martian, lunar, and other planetary body missions beyond low earth orbit. The research approach will consist of experimental and theoretical radiation modeling studies utilizing particle accelerator facilities including: 1. NASA Space Radiation Laboratory (NSRL) at Brookhaven National Laboratory; 2. Proton Synchrotron at Loma Linda University Medical Center; and 3. Los Alamos Neutron Science Center (LANSCE) at Los Alamos National Laboratory. Specifically, CRESSE investigators are designing, developing, and building experimental test beds that simulate the lunar and Martian radiation environments for experiments focused on risk assessment for astronauts and instrumentation. The testbeds have been designated the Bioastronautics Experimental Research Testbeds for Environmental Radiation Nostrum Investigations and Education (BERT and ERNIE). The designs of BERT and ERNIE will allow for a high degree of flexibility and adaptability to modify experimental configurations to simulate planetary surface environments, planetary habitats, and spacecraft interiors. In the nominal configuration, BERT and ERIE will consist of a set of experimental zones that will simulate the planetary atmosphere (Solid CO2 in the case of the Martian surface.), the planetary surface, and sub-surface regions. These experimental zones can be used for dosimetry, shielding, biological, and electronic effects radiation studies in support of space exploration missions. BERT and ERNIE are designed to be compatible with the experimental areas associated with the above facilities. CRESSE has broad expertise in space radiation in the areas of space radiation environment modeling, Monte-Carlo radiation transport modeling, space radiation instrumentation and dosimetry, radiation effects on electronics, and multi-functional composite shielding materials. The BERT and ERNIE testbeds will be utilized in individual and collaborative research incorporating this expertise. The research goal is to maximize the technical readiness level (TRL) of radiation instrumentation for human and robotic missions, optimizing the return value of CRESSE for NASA exploration and international co-operative missions. Outcomes and knowledge from research utilizing BERT and ERNIE will be applied to a variety of scientific and engineering disciplines vital for safe and reliable execution of future space exploration missions, which can be negatively impacted by the space radiation environment. The testbeds will be central to a variety of university educational activities and educational goals of NASA. Specifically, BERT and ERNIE will enhance educational opportunities in science, technology, engineering and mathematics (STEM) disciplines for engineering and science students at PVAMU, a historically black college/university. Preliminary data on prototype testbed configurations, including simulated lunar regolith (JSC-1A stimulant based on Apollo 11 samples), regolith/polyethylene composites, and dry ice, will be presented to demonstrate the usefulness of BERT and ERNIE in radiation beam line experiments.

Wilkins, Richard↗

NASA NTRS2011

Rapid Calculation of Spacecraft Trajectories Using Efficient Taylor Series Integration

A variable-order, variable-step Taylor series integration algorithm was implemented in NASA Glenn's SNAP (Spacecraft N-body Analysis Program) code. SNAP is a high-fidelity trajectory propagation program that can propagate the trajectory of a spacecraft about virtually any body in the solar system. The Taylor series algorithm's very high order accuracy and excellent stability properties lead to large reductions in computer time relative to the code's existing 8th order Runge-Kutta scheme. Head-to-head comparison on near-Earth, lunar, Mars, and Europa missions showed that Taylor series integration is 15.8 times faster than Runge- Kutta on average, and is more accurate. These speedups were obtained for calculations involving central body, other body, thrust, and drag forces. Similar speedups have been obtained for calculations that include J2 spherical harmonic for central body gravitation. The algorithm includes a step size selection method that directly calculates the step size and never requires a repeat step. High-order Taylor series integration algorithms have been shown to provide major reductions in computer time over conventional integration methods in numerous scientific applications. The objective here was to directly implement Taylor series integration in an existing trajectory analysis code and demonstrate that large reductions in computer time (order of magnitude) could be achieved while simultaneously maintaining high accuracy. This software greatly accelerates the calculation of spacecraft trajectories. At each time level, the spacecraft position, velocity, and mass are expanded in a high-order Taylor series whose coefficients are obtained through efficient differentiation arithmetic. This makes it possible to take very large time steps at minimal cost, resulting in large savings in computer time. The Taylor series algorithm is implemented primarily through three subroutines: (1) a driver routine that automatically introduces auxiliary variables and sets up initial conditions and integrates; (2) a routine that calculates system reduced derivatives using recurrence relations for quotients and products; and (3) a routine that determines the step size and sums the series. The order of accuracy used in a trajectory calculation is arbitrary and can be set by the user. The algorithm directly calculates the motion of other planetary bodies and does not require ephemeris files (except to start the calculation). The code also runs with Taylor series and Runge-Kutta used interchangeably for different phases of a mission.

Scott, James R.↗

NASA NTRSDate not supplied

Application Table: A Bridge Connecting the Designing “With-the-Material” and “the-Material”

Over the last few decades, advances in high-performance computing, new material characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. In 2016 NASA sponsored a 2040 Vision study (which appeared in 2018) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. The study envisions a cyber-physical-social ecosystem comprised of experimentally verified and validated (V & V) computational models, tools, and techniques, along with the associated digital tapestry, that impacts the entire supply chain to enable cost-effective, rapid, and revolutionary design of “fit-for-purpose” materials, components, and systems. Consequently, the development of a robust information management system that incorporates (across the full life cycle) both experimental (real data) and virtual data resulting from the application of various simulation tools (at single or multiple length scales), therefore enabling the virtual design and optimization of materials throughout their processing – internal structure – property – performance envelope, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality, and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. This is particularly true when attempting to merge ICME practices with recent additive manufacturing technology which will enable production of the resulting 2040 Vision material and structural designs. At NASA Glenn Research Center we are exploring the future of material science through the use of novel characterization methodologies, high performance computing, and recently an emphasis on integrated computational materials engineering (ICME). Herein, recent efforts to incorporate an Application Table within NASA Glenn Research Center’s ICME Granta MI database is presented. The goal is to provide a place where material and structural application information/requirements can be linked so as to marry the “design the-material” and the “design-with-material” paradigms and thereby enable application-driven design and optimization of materials and structures by providing a central location that links material processing at various length scales to the application’s performance requirements. This paper discusses the specifics of this Application Table as well as best practices and key principles for the development of a robust materials information management system to enable the 2040 Vision integrated materials and structures ecosystem. Furthermore, it presents the intended role of the Application Table in the future of ICME design of “fit-for-purpose” materials, showing the need for a well-established framework that can successfully bridge the gap between the design “the material” and design “with-the-material” paradigms.

Materials↗

NASA NTRS2006

Status of Solar Sail Propulsion: Moving Toward an Interstellar Probe

NASA's In-Space Propulsion Technology Program has developed the first-generation of solar sail propulsion systems sufficient to accomplish inner solar system science and exploration missions. These first-generation solar sails, when operational, will range in size from 40 meters to well over 100 meters in diameter and have an areal density of less than 13 grams-per-square meter. A rigorous, multiyear technology development effort culminated last year in the testing of two different 20-meter solar sail systems under thermal vacuum conditions. This effort provided a number of significant insights into the optimal design and expected performance of solar sails as well as an understanding of the methods and costs of building and using them. In a separate effort, solar sail orbital analysis tools for mission design were developed and tested. Laboratory simulations of the effects of long-term space radiation exposure were also conducted on two candidate solar sail materials. Detailed radiation and charging environments were defined for mission trajectories outside the protection of the earth's magnetosphere, in the solar wind environment. These were used in other analytical tools to prove the adequacy of sail design features for accommodating the harsh space environment. Preceding, and in conjunction with these technology efforts, NASA sponsored several mission application studies for solar sails, including one that would use an evolved sail capability to support humanity's first mission into nearby interstellar space. The proposed mission is called the Interstellar Probe. The Interstellar Probe might be accomplished in several ways. A 200-meter sail, with an areal density approaching 1 gram-per-square meter, could accelerate a robotic probe to the very edge of the solar system in just under 20 years from launch. A sail using the technology just demonstrated could make the same mission, but take significantly longer. Conventional chemical propulsion systems would require even longer flight times. Spinner sails of the type being explored by the Japanese may also be a good option, but the level of maturity in that technology is not clear. While the technology to support a 200-meter, ultralightweight sail mission is not yet in hand, the recent NASA investments in solar sail technology are an essential first step toward making it a reality. This paper will describe the status of solar sail propulsion within NASA, near-term solar sail mission applications, and the plan to advance the technology to the point where the Interstellar Probe mission can be flown.

Johnson, Les↗

NASA NTRS1961

A Study of Longitudinal Control Problems at Low and Negative Damping and Stability with Emphasis on Effects of Motion Cues

As part of a general investigation to determine the effects of simulator motions on pilot opinion and task performance over a wide range of vehicle longitudinal dynamics, a cooperative NASA-AMAL program was conducted on the centrifuge at Johnsville, Pennsylvania. The test parameters and measurements for this program duplicated those of earlier studies made at Ames Research Center with a variable-stability airplane and with a pitch-roll chair flight simulator. Particular emphasis was placed on the minimum basic damping and stability the pilots would accept and on the minimum dynamics they considered controllable in the event of stability-augmentation system failure. Results of the centrifuge-simulator program indicated that small positive damping was required by the pilots over most of the frequency range covered for configurations rated acceptable for emergency conditions only (e.g., failure of a pitch damper). It was shown that the pilot's tolerance for unstable dynamics was dependent primarily on the value of damping. For configurations rated acceptable for emergency operation only, the allowable instability and damping corresponded to a divergence time to double amplitude of about 1 second. Comparisons were made of centrifuge, pitch-chair and fixed-cockpit simulator tests with flight tests. Pilot ratings indicated that the effects of incomplete or spurious motion cues provided by these three modes of simulation were important only for high-frequency, lightly damped dynamics or unstable, moderately damped dynamics. The pitch- chair simulation, which provided accurate angular-acceleration cues to the pilot, compared most favorably with flight. For the centrifuge simulation, which furnished accurate normal accelerations but spurious pitching and longitudinal accelerations, there was a deterioration of pilots' opinion relative to flight results. Results of simulator studies with an analog pilot replacing the human pilot illustrated the adaptive capability of human pilots in coping with the wide range of vehicle dynamics and the control problems covered in this study. It was shown that pilot-response characteristics, deduced by the analog-pilot method, could be related to pilot opinion. Possible application of these results for predicting flight-control problems was illustrated by means of an example control-problem analysis. The results of a brief evaluation of a pencil-type side-arm controller in the centrifuge showed a considerable improvement in the pilots' ability to cope with high-frequency, low-damping dynamics, compared to results obtained with the center stick. This improvement with the pencil controller was attributed primarily to a marked reduction in the adverse effects of large and exaggerated pitching and longitudinal accelerations on pilot control precision.

Sadoff, Melvin↗

NASA NTRS1988

Formation of curved seafloor fabric by changes in rift propagation velocity and spreading rate - Application to the 95.5 deg W Galapagos propagator

Possible rigid plate models and shear models for the formation of curved seafloor lineaments by rift propagation are investigated and are applied to the Galapagos propagation rift system at 95 deg W. It is shown that the geometry noted at the Galapagos can result from either rift propagation acceleration or a spreading rate decrease during the last few hundred thousand years. It is postulated that the reverse curvature could result from either deceleration of rift propagation or an increase in spreading rate. The data interpreted as requiring a shear zone are found to be equally consistent with two distinct models based on rigid plate tectonics.

Acton, Gary↗

NASA NTRS1998

Simulation Accelerator

Under a NASA SBIR (Small Business Innovative Research) contract, (NAS5-30905), EAI Simulation Associates, Inc., developed a new digital simulation computer, Starlight(tm). With an architecture based on the analog model of computation, Starlight(tm) outperforms all other computers on a wide range of continuous system simulation. This system is used in a variety of applications, including aerospace, automotive, electric power and chemical reactors.

Source record↗

NASA NTRSDate not supplied

Accelerating the Deployment of Space-Based Quantum Sensors

The Space Science and Technology Partnership Forum (S&T Forum), comprised of an interagency team from the National Aeronautics and Space Administration, the National Reconnaissance Office, and the United States Space Force, presents findings and recommendations from a study on the state of quantum sensors for space applications, enabling component technologies, facilities, and developers across government, industry, and academia. The following five areas of quantum sensing technology (listed in alphabetical order) were identified as being of near-term interest to all three S&T Forum agencies: atomic clocks, atom interferometers, quantum magnetometers, Rydberg sensors, and single photon detectors. This paper focuses on two recommendations: 1) increased collaboration between the S&T Forum, industry, and academia on the development of enabling components for the five quantum sensing technology areas, and 2) challenges and future opportunities to take quantum sensors from the laboratory to space. Through this study, the S&T Forum found a diverse and broad community of quantum sensing developers in the United States that are leading efforts in research, testing, manufacturing, and qualification of quantum sensors and their enabling component technologies. There are common needs across quantum sensing technology areas. To address the common needs, the S&T Forum agencies are encouraged to utilize existing models and mechanisms to enable co-development of enabling component technologies and to explore new avenues for engagement with the quantum sensing community.

Grace C Ray↗

NASA NTRSDate not supplied

Accelerating the Deployment of Space-Based Quantum Sensors

The Space Science and Technology Partnership Forum (S&T Forum), comprised of an interagency team from the National Aeronautics and Space Administration, the National Reconnaissance Office, and the United States Space Force, presents findings and recommendations from a study on the state of quantum sensors for space applications, enabling component technologies, facilities, and developers across government, industry, and academia. The following five areas of quantum sensing technology (listed in alphabetical order) were identified as being of near-term interest to all three S&T Forum agencies: atomic clocks, atom interferometers, quantum magnetometers, Rydberg sensors, and single photon detectors. This paper focuses on two recommendations: 1) increased collaboration between the S&T Forum, industry, and academia on the development of enabling components for the five quantum sensing technology areas, and 2) challenges and future opportunities to take quantum sensors from the laboratory to space. Through this study, the S&T Forum found a diverse and broad community of quantum sensing developers in the United States that are leading efforts in research, testing, manufacturing, and qualification of quantum sensors and their enabling component technologies. There are common needs across quantum sensing technology areas. To address the common needs, the S&T Forum agencies are encouraged to utilize existing models and mechanisms to enable co-development of enabling component technologies and to explore new avenues for engagement with the quantum sensing community.

Grace C Ray↗

NASA NTRS2022

Application Table: A Bridge Connecting the Designing “With-The-Material” and “The-Material” Paradigms

Over the last few decades, advances in high-performance computing, new material characterization methods, and, more recently, an emphasis on integrated computational materials engineering (ICME) have been a catalyst for multiscale modeling and simulation-based design of materials and structures in the aerospace industry. In 2016 NASA sponsored a 2040 Vision study (which appeared in 2018) to define the potential 25-year future state required for integrated multiscale modeling of materials and systems (e.g., load-bearing structures) to accelerate the pace and reduce the expense of innovation in future aerospace and aeronautical systems. The study envisions a cyber-physical-social ecosystem comprised of experimentally verified and validated (V & V) computational models, tools, and techniques, along with the associated digital tapestry, that impacts the entire supply chain to enable cost-effective, rapid, and revolutionary design of “fit-for-purpose” materials, components, and systems. Consequently, the development of a robust information management system that incorporates (across the full life cycle) both experimental (real data) and virtual data resulting from the application of various simulation tools (at single or multiple length scales), therefore enabling the virtual design and optimization of materials throughout their processing – internal structure – property – performance envelope, has become critical. This need is also fueled by the demands for higher efficiency in material testing; consistency, quality, and traceability of data; product design; engineering analysis; as well as control of access to proprietary or sensitive information. This is particularly true when attempting to merge ICME practices with recent additive manufacturing technology which will enable production of the resulting 2040 Vision material and structural designs. At NASA Glenn Research Center we are exploring the future of material science through the use of novel characterization methodologies, high performance computing, and recently an emphasis on integrated computational materials engineering (ICME). Herein, recent efforts to incorporate an Application Table within NASA Glenn Research Center’s ICME Granta MI database is presented. The goal is to provide a place where material and structural application information/requirements can be linked so as to marry the “design the-material” and the “design-with-material” paradigms and thereby enable application-driven design and optimization of materials and structures by providing a central location that links material processing at various length scales to the application’s performance requirements. This paper discusses the specifics of this Application Table as well as best practices and key principles for the development of a robust materials information management system to enable the 2040 Vision integrated materials and structures ecosystem. Furthermore, it presents the intended role of the Application Table in the future of ICME design of “fit-for-purpose” materials, showing the need for a well-established framework that can successfully bridge the gap between the design “the material” and design “with-the-material” paradigms.

Materials↗

NASA NTRS2001

Micromachined TWTs for THz Radiation Sources

The Terahertz (THz) region of the electromagnetic spectrum (about 300 - 3000 GHz in frequency or about 0.1 - 1 mm free space wavelength) has enormous potential for high-data-rate communications, spectroscopy, astronomy, space research, medicine, biology, surveillance, remote sensing, industrial process control, etc. It has been characterized as the most scientifically rich, yet under-utilized, region of the electromagnetic spectrum. The most critical roadblock to full exploitation of the THz band is lack of coherent radiation sources that are powerful (0.001 - 1.0 W continuous wave), efficient (> 1%), frequency agile (instantaneously tunable over 1% bandwidths or more), reliable, and comparatively inexpensive. To develop vacuum electron device (VED) radiation sources satisfying these requirements, fabrication and packaging approaches must be heavily considered to minimize costs, in addition to the basic interaction physics and circuit design. To minimize size of the prime power supply, beam voltage must be minimized, preferably 10 kV. Solid state sources satisfy the low voltage requirement, but are many orders of magnitude below power, efficiency, and bandwidth requirements. On the other hand, typical fast-wave VED sources in this regime (e.g., gyrotrons, FELs) tend to be large, expensive, high voltage and very high power devices unsuitable for most of the applications cited above. VEDs based on grating or inter-digital (ID) circuits have been researched and developed. However, achieving forward-wave amplifier operation with instantaneous fractional bandwidths > 1% is problematic for these devices with low-energy (< 15 kV) electron beams. Moreover, the interaction impedance is quite low unless the beam-circuit spacing is kept particularly narrow, often leading to significant beam interception. One solution to satisfy the THz source requirements mentioned above is to develop micromachined VEDs, or "micro-VEDs". Among other benefits, micro-machining technologies provide superior high frequency wall conductivity as a result of superior surface smoothness compared with conventional mechanical or electric discharge machining approaches. Micro-VED technologies are already being applied to the development of millimeter-wave klystrons at Stanford Linear Accelerator Center and submillimeter-wave klystrons at the University of Leeds. We are investigating the use of micro-machining technologies to develop THz regime TWTs, with emphasis on folded-waveguide TWTs. The folded-waveguide TWT (FW-TWT) has several features that make it attractive for THz-regime micro-VED applications. It is a relatively simple circuit to design and fabricate, it is amenable to precision pattern replication by micro-machining, and it is has been demonstrated capable of forward-wave amplification with appreciable bandwidth. We are conducting experimental and computational studies of micro-VED FW-TWTs to examine their feasibility for applications at frequencies from 200 - 1000 GHz.

Booske, John H.↗

NASA NTRS2011

Failure Modes in Capacitors When Tested Under a Time-Varying Stress

Steady step surge testing (SSST) is widely applied to screen out potential power-on failures in solid tantalum capacitors. The test simulates the power supply's on and off characteristics. Power-on failure has been the prevalent failure mechanism for solid tantalum capacitors for decoupling applications. On the other hand, the SSST can also be reviewed as an electrically destructive test under a time-varying stress. It consists of rapidly charging the capacitor with incremental voltage increases, through a low resistance in series, until the capacitor under test is electrically shorted. Highly accelerated life testing (HALT) is usually a time-efficient method for determining the failure mechanism in capacitors; however, a destructive test under a time-varying stress like SSST is even more effective. It normally takes days to complete a HALT test, but it only takes minutes for a time-varying stress test to produce failures. The advantage of incorporating specific time-varying stress into a statistical model is significant in providing an alternative life test method for quickly revealing the failure modes in capacitors. In this paper, a time-varying stress has been incorporated into the Weibull model to characterize the failure modes. The SSST circuit and transient conditions to correctly test the capacitors is discussed. Finally, the SSST was applied for testing polymer aluminum capacitors (PA capacitors), Ta capacitors, and multi-layer ceramic capacitors with both precious metal electrode (PME) and base-metal-electrodes (BME). It appears that testing results are directly associated to the dielectric layer breakdown in PA and Ta capacitors and are independent on the capacitor values, the way the capacitors being built, and the manufactures. The testing results also reveal that ceramic capacitors exhibit breakdown voltages more than 20 times the rated voltage, and the breakdown voltages are inverse proportional to the dielectric layer thickness. The possibility of ceramic capacitors in front-end decoupling applications to block the surge noise from a power supply is also discussed.

Liu, David (Donhang)↗

NASA NTRS1984

Discrimination of coherent features in turbulent boundary layers by the entropy method

Entropy in information theory is defined as the expected or mean value of the measure of the amount of self-information contained in the ith point of a distribution series x sub i, based on its probability of occurrence p(x sub i). If p(x sub i) is the probability of the ith state of the system in probability space, then the entropy, E(X) = - sigma p(x sub i) logp (x sub i), is a measure of the disorder in the system. Based on this concept, a method was devised which sought to minimize the entropy in a time series in order to construct the signature of the most coherent motions. The constrained minimization was performed using a Lagrange multiplier approach which resulted in the solution of a simultaneous set of non-linear coupled equations to obtain the coherent time series. The application of the method to space-time data taken by a rake of sensors in the near-wall region of a turbulent boundary layer was presented. The results yielded coherent velocity motions made up of locally decelerated or accelerated fluid having a streamwise scale of approximately 100 nu/u(tau), which is in qualitative agreement with the results from other less objective discrimination methods.

Corke, T. C.↗

NASA NTRS1985

Visceral predictors of cardiovascular deconditioning in late middle-aged men

A number of visceral and behavioral factors connected with cardiovascular deconditioning were investigated, in order to identify a method for predicting the degree of orthostatic intolerance to spaceflight in several late-middle-aged men (55-65 years). Preliminary measurements were made of: mean arterial blood pressure plasma cortisol levels; and norepinephrine levels. Measurements of core temperature; plasma epinephrine level and subjective arousal from sleep were also obtained. Pairwise correlations were found for each of the variables and the time-to-blackout due centrifugal acceleration of up to +3 Gz. It is shown that the men with relatively low resting blood pressure were at greater risk of developing the clinical signs of cardiovascular deconditioning than were the men with higher basal blood pressure. Some applications of the experimental results to the development of selection criteria for Shuttle crews are discussed.

Goldwater, D. J.↗

NASA NTRS1992

Relativistic magnetosonic shock waves in synchrotron sources - Shock structure and nonthermal acceleration of positrons

The theoretical properties of relativistic, transverse, magnetosonic collisionless shock waves in electron-positron-heavy ion plasmas of relevance to astrophysical sources of synchrotron radiation are investigated. Both 1D electromagnetic particle-in-cell simulations and quasi-linear theory are used to examine the spatial and kinetic structure of these nonlinear flows. A new process of shock acceleration of nonthermal positrons, in which the gyrating reflected heavy ions dissipate their energy in the form of collectively emitted, left-handed magnetosonic waves which are resonantly absorbed by the positrons immediately behind the ion reflection region, is described. Applications of the results to the termination shocks of pulsar winds and to the termination shocks of jets emanating from the AGN are outlined.

Hoshino, Masahiro↗