SEARCH · Engineering Papers

Results for “tailoring”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Time-dependent quasi-one-dimensional simulations of high enthalpy pulse facilities

A numerical methodology is presented for simulating the time-dependent reacting flow inside the entire length of high enthalpy pulse facilities. The methodology is based on a finite-volume TVD scheme for the quasi-1D Euler equations coupled with finite-rate chemistry. A moving mesh and tracking of gas interfaces are used to overcome certain numerical difficulties associated with these types of flows. Simulation results of a helium driven shock tube show that computations can be used to predict the off-tailored behavior of shock tubes and tunnels. Particular attention is given to computations of the flow through the NASA Ames 16-inch combustion driven shock tunnel which show the influence of nonuniformities in the driver section on the reservoir conditions; and the effect of finite secondary diaphragm opening times on the chemical composition of the test flow in the HYPULSE expansion tube.

Wilson, Gregory J.↗

NASA NTRS1993

Aerothermodynamic performance and thermal protection design for blunt re-entry bodies at L/D = 0.3

Aerodynamic heating and thermal protection design analyses were performed for three blunt re-entry bodies at an L/D = 0.3 returning from low earth orbit. These configurations consisted of a scaled up Apollo command module, a Viking re-entry vehicle, and an Aeroassist Flight Experiment (AFE) aerobrake, each with a maximum diameter of 4.42 m. The aerothermodynamic analysis determined the equilibrium stagnation point heating rate and heat load for nominal and 3-sigma re-entry trajectories and the distribution of heating along the pitch and yaw planes for each of the vehicles at the time of highest heat flux. Using the predicted heating rates and heating distributions, a Thermal Protection System (TPS) design with flight certified materials was tailored for each of the configurations. Results indicated that the heating to the corner of the Viking aeroshell would exceed current limits of reusable tile material. Also, the maximum heating for the AFE would be 15 percent greater than the maximum heating for the Apollo flying the same trajectory. TPS designs showed no significant advantage in TPS weight between the different vehicles; however, heat-shield areal density comparisons showed the Apollo configuration to be the most efficient in terms of TPS weight.

Caram, Jose M.↗

NASA NTRS1992

Imaging solar flares in hard X-rays using Fourier telescopes

The sun emits hard X-rays (above 10 keV) during solar flares. Imaging hard X-ray sources on the sun with spatial resolutions on the order of 1-5 arcsec and integration times of 1 sec will provide greater insight into the energy release processes during a solar flare. In these events, tremendous amounts of energy stored in the solar magnetic field are rapidly released leading to emission across the electromagnetic spectrum. Two Fourier telescope designs, a spatial modulation collimator and a rotating modulation collimator, were developed to image the full sun in hard X-rays (10-100 keV) in an end-to-end simulation. Emission profiles were derived for two hard X-ray solar flare models taken from the current solar theoretical literature and used as brightness distributions for the telescope simulations. Both our telescope models, tailored to image solar sources, were found to perform equally well, thus offering the designer significant flexibility in developing systems for space-based platforms. Given sufficient sensitive areas, Fourier telescopes are promising concepts for imaging solar hard X-rays.

Campbell, Jonathan W.↗

NASA NTRS1993

NDE of the universe - New ways to look at old facts

The paper investigates the relation between cosmology and NDE, emphasizing the need for new approaches and models imposed by new space-age materials. These are frontier materials with tailored microstructures and specially designed properties, such as the ceramic and intermetallic matrix composites for very high temperature power and propulsion systems. These materials require new NDE approaches, which are discussed in this paper.

Vary, Alex↗

NASA NTRS1993

Improvements in hover display dynamics for a combat helicopter

This paper describes a piloted simulation conducted on the NASA Ames Vertical Motion Simulator. The objective of the experiment was to investigate the handling qualities benefits attainable using new display law design methods for hover displays. The new display laws provide improved methods to specify the behavior of the display symbol that predicts the vehicle's ground velocity in the horizontal plane; it is the primary symbol that the pilot uses to control aircraft horizontal position. The display law design was applied to the Apache helmet-mounted display format, using the Apache vehicle dynamics to tailor the dynamics of the velocity predictor symbol. The representations of the Apache vehicle used in the display design process and in the simulation were derived from flight data. During the simulation, the new symbol dynamics were seen to improve the pilots' ability to maneuver about hover in poor visual cuing environments. The improvements were manifested in pilot handling qualities ratings and in measured task performance. The paper details the display design techniques, the experiment design and conduct, and the results.

Eshow, Michelle M.↗

NASA NTRS1991

Advanced Si IR detectors using molecular beam epitaxy

SiGe/Si heterojunction internal photoemission (HIP) long wavelength infrared (LWIR) detectors have been fabricated by MBE. The SiGe/Si HIP detector offers a tailorable spectral response in the long wavelength infrared regime by varying the SiGe/Si heterojunction barrier. Degenerately doped p(+) SiGe layers were grown using elemental boron, as the dopant source allows a low growth temperature. Good crystalline quality was achieved for boron-doped SiGe due to the reduced growth temperature. The dark current density of the boron-doped HIP detectors was found to be thermionic emission limited. HIP detectors with a 0.066 eV were fabricated and characterized using activation energy analysis, corresponding to a 18 micron cutoff wavelength. Photoresponse of the detectors at wavelengths ranging from 2 to 12 microns has been characterized with corresponding quantum efficiencies of 5 - 0.1 percent.

Lin, T. L.↗

NASA NTRS1992

Composite materials for structures on planetary surfaces

The physical and mechanical properties of advanced composite materials as related to their use in structures on planetary surfaces are reviewed. Polymer matrix composites are recommended as the best materials in the first exploration stages. Achievement of mechanical properties, physical properties, improved processability, and ease of assembly required on planetary surfaces depends on the tailorability of composites.

Radford, Donald W.↗

NASA NTRS1993

Advanced particulate fibrous composite for thermal control of re-entry vehicles

Combining the selectively reflective properties of particulate reflective coatings with the low density and high temperature capability of ceramic fibrous materials results in a novel composite material with useful optical properties. Numerical predictions of the radiative properties of zirconia and silica composites for a range of mixture fractions and wavelengths show the improvements attainable by dispersing spheres throughout a fiber matrix. The radiation conductance is controlled by the percentage of spheres in the composite. Results show that specific wavelength domains are controlled by either the spheres or the fibers, so the optical properties can be tailored for reentry applications.

White, Susan↗

NASA NTRS1985

Stiffener attachment concepts for graphite-epoxy panels designed for postbuckling strength

Stiffener attachment concepts for suppressing or delaying the onset of the skin-stiffener separation failure mode in graphite-epoxy compression panels designed for postbuckling strength were experimentally studied. The effectiveness of these concepts was evaluated using panels with 16-ply skins and a single centrally-located I-shaped stiffener with both static and cyclic compressive loadings. Analytical results suggest that tailoring the relative thicknesses of the panel skin, stiffener attachment flange, and the stiffener web rotational stiffness can minimize the adverse effects of high interface shear and normal stresses. Interface stress levels may be reduced by tapering the thickness of the stiffener attachment flange and properly selecting the stacking sequences of the skin and stiffener attachment flange laminates.

Dickson, John N.↗

NASA NTRS1991

Vision based techniques for rotorcraft low altitude flight

An overview of research in obstacle detection at NASA Ames Research Center is presented. The research applies techniques from computer vision to automation of rotorcraft navigation. The development of a methodology for detecting the range to obstacles based on the maximum utilization of passive sensors is emphasized. The development of a flight and image data base for verification of vision-based algorithms, and a passive ranging methodology tailored to the needs of helicopter flight are discussed. Preliminary results indicate that it is possible to obtain adequate range estimates except at regions close to the FOE. Closer to the FOE, the error in range increases since the magnitude of the disparity gets smaller, resulting in a low SNR.

Sridhar, Banavar↗

NASA NTRS1993

Hybrid propulsion based on fluid-controlled solid gas generators

The use of fuel-rich solid (gas generator-type) propellants for hybrid propulsion affords some design and utilization efficiency advantages. Both forward and aft liquid injection control concepts are evaluated from the operational standpoints of ballistics, throttling, stability and extinguishment. Steady-state and non-steady ballistics analyses are employed for this evaluation. Stability of solid motor operation is enhanced by fluid injection with adequate injector pressure drop. Efficient throttling and reliable extinguishment are attained through a combination of solid propellant combustion tailoring, grain design, control valves and sensors. Initial results from a laboratory-scale slab combustor, combining a gas generator propellant with gaseous oxygen injection, are also presented.

Cohen, Norman S.↗

NASA NTRS1990

A laboratory means to produce tough aluminum sheet from powder

The rapid solidification of aluminum alloys as powder and the subsequent fabrication processes can be used to develop and tailor alloys to satisfy specific aerospace design requirements, including high strength and toughness. Laboratory procedures to produce aluminum powder-metallurgy (PM) materials are efficient but require evidence that the laboratory methods used can produce a product with superior properties. This paper describes laboratory equipment and procedures which can be used to produce tough aluminum PM sheet. The processing of a 2124 + 0.9 percent Zr aluminum alloy powder is used as an example. The fully hardened sheet product is evaluated in terms of properties and microstructure. The key features of the vacuum hot press pressing operation used to consolidate the powder are described. The 2124 + 0.9 percent Zr - T8 temper aluminum sheet produced was both strong (460-490 MPa yield strength) and tough (Kahn Tear unit-propagation- energy values over three times those typical for ingot metallurgy 2024-T81). Both the longitudinal and longitudinal-transverse directions of the sheet were tested. The microstructure was well refined with subgrains of one or two micrometers. Fine dispersoids of Al3Zr in the precipitate free regions adjacent to boundaries are believed to contribute to the improved toughness.

Singleton, O. R.↗

NASA NTRS1993

Fabrication and properties of functionally graded NiAl/Al2O3 composites

A modified sedimentation process was used in the production of a functionally gradient material (FGM), NiAl/Al2O3. A simple finite element model was used to guide our design and fabrication efforts by estimating residual stress states as a function of composite structure. This approach could lead to tailored designs that enhance or avoid specific residual stress states. Thermal cycling tests were factored into the model to predict time dependent or steady-state internal temperature and stress profiles. Four-point bend tests were conducted to establish the mechanical load-displacement behavior of a single interlayer FGM at room temperature, 800 and 1000 K. Room temperature bend strength of the FGM was 3-4 times that of the base NiAl. At elevated temperatures, composite fracture occurred in a gradual, noncatastrophic mode involving NiAl retardation of a succession of cracks originating in the alumina face.

Miller, D. P.↗

NASA NTRS1993

The EUVE Guest Observer Program

Following the completion of the EUVE all-sky survey, the balance of the mission is being conducted as a Guest Observer Program, under which the astronomical community may propose to make pointed spectroscopic observations in the EUV. The spectrometer covers the wavelength range 70-760 A in three overlapping bands at a resolution of 100-400. Guest observers receive time-tagged photon event lists together with instrument and spacecraft housekeeping data. Data are delivered with software tools that run in the Image Reduction and Analysis Facility and are tailored for handling EUVE satellite data.

Miller, Anne B.↗

NASA NTRS1983

Neutron transmutation doped Ge bolometers

Some conclusions reached are as follow. Neutron Transmutation Doping (NTD) of high quality Ge single crystals provides perfect control of doping concentration and uniformity. The resistivity can be tailored to any given bolometer operating temperature down to 0.1 K and probably lower. The excellent uniformity is advantaged for detector array development.

Haller, E. E.↗

NASA NTRS1987

Efficient optimization of integrated aerodynamic-structural design

The introduction of composite materials is having a profound effect on the design process. Because these materials permit the designer to tailor material properties to improve structural, aerodynamic and acoustic performance, they require a more integrated multidisciplinary design process. Because of the complexity of the design process numerical optimization methods are required. The present paper is focused on a major difficulty associated with the multidisciplinary design optimization process - its enormous computational cost. We consider two approaches for reducing this computational burden: (1) development of efficient methods for cross-sensitivity calculation using perturbation methods; and (2) the use of approximate numerical optimization procedures. Our efforts are concentrated upon combined aerodynamic-structural optimization. Results are presented for the integrated design of a sailplane wing. The impact of our computational procedures on the computational costs of integrated costs of integrated designs are discussed.

Haftka, R. T.↗

NASA NTRS1991

Advanced propulsion concepts

The topics presented are covered in viewgraph form. The programmatic objective is to establish the feasibility of propulsion technologies for vastly expanded space activity. The technical objective is a revolutionary performance sought, such as: (1) about 1 kg/kW specific mass; (2) specific impulse tailored to mission requirements; (3) ability to use in-situ resources; (4) round-trips to Mars in months; (5) round-trips to outer planets in 1 to 2 years; and (6) the capability for robotic mission beyond the solar system.

Sercel, Joel C.↗

NASA NTRS1988

Aircraft integrated design and analysis: A classroom experience

AAE 451 is the capstone course required of all senior undergraduates in the School of Aeronautics and Astronautics at Purdue University. During the past year the first steps of a long evolutionary process were taken to change the content and expectations of this course. These changes are the result of the availability of advanced computational capabilities and sophisticated electronic media availability at Purdue. This presentation will describe both the long range objectives and this year's experience using the High Speed Commercial Transport (HSCT) design, the AIAA Long Duration Aircraft design and a Remotely Piloted Vehicle (RPV) design proposal as project objectives. The central goal of these efforts was to provide a user-friendly, computer-software-based, environment to supplement traditional design course methodology. The Purdue University Computer Center (PUCC), the Engineering Computer Network (ECN), and stand-alone PC's were used for this development. This year's accomplishments centered primarily on aerodynamics software obtained from the NASA Langley Research Center and its integration into the classroom. Word processor capability for oral and written work and computer graphics were also blended into the course. A total of 10 HSCT designs were generated, ranging from twin-fuselage and forward-swept wing aircraft, to the more traditional delta and double-delta wing aircraft. Four Long Duration Aircraft designs were submitted, together with one RPV design tailored for photographic surveillance. Supporting these activities were three video satellite lectures beamed from NASA/Langley to Purdue. These lectures covered diverse areas such as an overview of HSCT design, supersonic-aircraft stability and control, and optimization of aircraft performance. Plans for next year's effort will be reviewed, including dedicated computer workstation utilization, remote satellite lectures, and university/industrial cooperative efforts.

Source record↗