Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “support effects”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Theoretical H + O 3 rate coefficients from ring polymer molecular dynamics on an accurate global potential energy surface: assessing experimental uncertainties

Thermal rate coefficients and kinetic isotope effects have been calculated for an important atmospheric reaction H/D + O 3 → OH/OD + O2 based on an accurate permutation invariant polynomial-neural network potential energy surface, using ring polymer molecular dynamics (RPMD), quasi-classical trajectory (QCT) and variational transition-state theory (VTST) with multidimensional tunneling. The RPMD approach yielded results that are generally in better agreement with experimental rate coefficients than the VTST and QCT ones, especially at low temperatures, attributable to its capacity to capture quantum effects such as tunneling and zero-point energy. Additionally, the theoretical results support one group of existing experiments over the other. In addition, rate coefficients for the D + O 3 → OD + O 2 reaction are also reported using the same methods, which will allow a stringent assessment of future experimental measurements, thus helping to reduce the uncertainty in the recommended rate coefficients of this reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Shoulder fillet effects in strength distributions of microelectromechanical system components

The failure forces and fracture strengths of polysilicon microelectromechanical system (MEMS) components in the form of stepped tensile bars with shoulder fillets were measured using a sequential failure chain methodology. Approximately 150 specimens for each of four fillet geometries with different stress concentration factors were tested. The resulting failure force and strength distributions of the four geometries were related by a common sidewall flaw population existing within different effective stressed lengths. The failure forces, strengths, and flaw population were well described by a weakest-link based analytical framework. Finite element analysis was used to verify body-force based expressions for the stress concentration factors and to provide insight into the variation of specimen effective length with fillet geometry. Monte Carlo simulations of flaw size and location, based on the strength measurements, were also used to provide insight into fillet shape and size effects. The successful description of the shoulder fillet specimen strengths provides further empirical support for application of the strength and flaw framework in MEMS fabrication and design optimization.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Design of passive and structural conductors for tokamaks using thin-wall eddy current modeling

Abstract A new three-dimensional electromagnetic modeling tool ( ThinCurr ) has been developed using the existing PSI-Tet finite-element code in support of conducting structure design work for both the SPARC and DIII-D tokamaks. Within this framework a 3D conducting structure model was created for both the SPARC and DIII-D tokamaks in the thin-wall limit. This model includes accurate details of the vacuum vessel and other conducting structural elements with realistic material resistivities. This model was leveraged to support the design of a passive runaway electron mitigation coil (REMC), studying the effect of various design parameters, including coil resistivity, current quench duration, and plasma vertical position, on the effectiveness of the coil. The REMC is a non-axisymmetric coil designed to passively drive large non-axisymmetric fields during the plasma disruption thereby destroying flux surfaces and deconfining RE seed populations. These studies indicate that current designs should apply substantial 3D fields at the plasma surface during future plasma current disruptions as well as highlight the importance of having the REMC conductors away from the machine midplane in order to ensure they are robust to off-normal disruption scenarios.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Global stellarator coil optimization with quadratic constraints and objectives

Most present stellarator designs are produced by costly two-stage optimization: the first for an optimized equilibrium, and the second for a coil design reproducing its magnetic configuration. Few proxies for coil complexity and forces exist at the equilibrium stage. Rapid initial state finding for both stages is a topic of active research. Most present convex coil optimization codes use the least square winding surface method by Merkel (NESCOIL), with recent improvements in conditioning, regularization, sparsity, and physics objectives. While elegant, the method is limited to modeling the norms of linear functions in coil current. We present QUADCOIL, a global coil optimization method that targets combinations of linear and quadratic functions of the current. It can directly constrain and/or minimize a wide range of physics objectives unavailable in NESCOIL and REGCOIL, including the Lorentz force, magnetic energy, curvature, field-current alignment, and the maximum density of a dipole array. QUADCOIL requires no initial guess and runs nearly $10$ 2 x faster than filament optimization. Integrating it in the equilibrium optimization stage can potentially exclude equilibria with difficult-to-design coils, without significantly increasing the computation time per iteration. QUADCOIL finds the exact, global minimum in a large parameter space when possible, and otherwise finds a well-performing approximate global minimum. It supports most regularization techniques developed for NESCOIL and REGCOIL. We demonstrate QUADCOIL’s effectiveness in coil topology control, minimizing non-convex penalties, and predicting filament coil complexity with three numerical examples.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Magnetoelastic coupling anisotropy in the Kitaev material α-RuCl 3

Here we show that the Kitaev material α-RuCl 3 is among the most prominent candidates to host a quantum spin-liquid state endowed with fractionalized excitations. Recent experimental and theoretical investigations have separately revealed the importance of both the magnetoelastic coupling and the magnetic anisotropy in dependence of the applied magnetic-field direction. In this combined theoretical and experimental research, we investigate the anisotropic magnetic and magnetoelastic properties for magnetic fields applied along the main crystallographic axes as well as for fields canted out of the honeycomb plane. We found that the magnetostriction anisotropy is unusually large compared to the anisotropy of the magnetization, which is related to the strong magnetoelastic $\tilde{Γ}'$-type coupling in our ab-initio derived model. We observed large, nonsymmetric magnetic anisotropy for magnetic fields canted out of the honeycomb ab plane in opposite directions, namely, toward the +c* or -c* axes, respectively. The observed directional anisotropy is explained by considering the relative orientation of the magnetic field with respect to the coaligned RuCl 6 octahedra. Magnetostriction measurements in canted fields support this nonsymmetric magnetic anisotropy; however, these experiments are affected by magnetic torque effects. Comparison of theoretical predictions with experimental findings allow us to recognize the significant contribution of torque effects in experimental setups where α-RuCl 3 is placed in canted magnetic fields.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

DMFT Reveals the Non-Hermitian Topology and Fermi Arcs in Heavy-Fermion Systems

When a strongly correlated system supports well-defined quasiparticles, it allows for an elegant one-body effective description within the non-Hermitian topological theory. While the microscopic many-body Hamiltonian of a closed system remains Hermitian, the one-body quasiparticle Hamiltonian is non-Hermitian due to the finite quasiparticle lifetime. We use such a non-Hermitian description in the heavy-fermion two-dimensional systems with the momentum-dependent hybridization to reveal a fascinating phenomenon which can be directly probed by the spectroscopic measurements, the bulk “Fermi arcs.” Starting from a simple two-band model, we first combine the phenomenological approach with the perturbation theory to show the existence of the Fermi arcs and reveal their connection to the topological exceptional points, special points in the Brillouin zone where the Hamiltonian is nondiagonalizable. The appearance of such points necessarily requires that the electrons belonging to different orbitals have different lifetimes. This requirement is naturally satisfied in the heavy-fermion systems, where the itinerant c electrons experience much weaker interaction than the localized f electrons. We then utilize the dynamical mean field theory to numerically calculate the spectral function and confirm our findings. We show here that the concept of the exceptional points in the non-Hermitian quasiparticle Hamiltonians is a powerful tool for predicting new phenomena in strongly correlated electron systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Boundary Modes from Periodic Magnetic and Pseudomagnetic Fields in Graphene

Single-layer graphene subject to periodic lateral strains is an artificial crystal that can support boundary spectra with an intrinsic polarity. This is analyzed by comparing the effects of periodic magnetic fields and strain-induced pseudomagnetic fields that, respectively, break and preserve time-reversal symmetry. In the former case, a Chern classification of the superlattice minibands with zero total magnetic flux enforces single counterpropagating modes traversing each bulk gap on opposite boundaries of a nanoribbon. For the pseudomagnetic field, pairs of counterpropagating modes migrate to the same boundary where they provide well-developed valley-helical transport channels on a single zigzag edge. Here, we discuss possible schemes for implementing this situation and their experimental signatures.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Saturation of magnetized plasma turbulence by propagating zonal flows

Strongly driven ion-scale turbulence in tokamak plasmas is shown to be regulated by a new propagating zonal flow mode, the toroidal secondary mode, which is nonlinearly supported by the turbulence. The mode grows and propagates due to the combined effects of zonal flow shearing and advection by the magnetic drift. Above a threshold in the turbulence level, small-scale toroidal secondary modes become unstable and shear apart turbulent eddies, forcing the turbulence level to remain near the threshold. This threshold condition is used to derive scaling laws for the turbulent heat flux, fluctuation spectra, and zonal flow amplitude, which are validated in nonlinear gyrokinetic simulations and explain previous experimental observations.

Nies, Richard [Princeton Univ., NJ (United States)↗
DOE OSTI2022

Quantitative Metrics for Grid Resilience Evaluation and Optimization

Power system resilience has become a critical topic in recent years because of the increasing trend of extreme events and the growing integration of intermittent renewable energy sources. To enhance grid resilience against high-impact, low-frequency events, two questions should be answered: how to quantify the resilience of a given grid and how to incorporate the quantification into power system planning, operation, and restoration. Here this paper develops a new set of quantitative metrics with clear physical interpretation to comprehensively evaluate power system resilience. Using microgrids as an example, an event-based corrective scheduling (ECS) model and an online model predictive control (OMPC) model are developed to integrate the proposed quantitative resilience metrics into power system optimization models for resilience enhancement. The ECS model employs extreme event data to investigate the optimal restoration solution and to help microgrid operators prepare to respond to similar events. The OMPC model provides online decision-making support for operators to handle ongoing outages in the most resilient fashion. The effectiveness and superiority of the proposed quantitative resilience metrics and the resilience enhancement models are demonstrated through simulations and comparative studies on an IEEE test feeder and a real distribution feeder in Southern California.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2020

Modeling of Atom Interferometer Accelerometer

This report presents the theoretical effort to model and simulate the atom-interferometer accelerometer operating in a highly mobile environment. Multitudes of non-idealities may occur in such a rapidly-changing environment with a large acceleration whose amplitude and direction both change quickly. We studied the undesired effect of high mobility in the atom-interferometer accelerator in a detailed model and a simulator. The undesired effects include the atom cloud's movement during Raman pulses, the Doppler effect due to the relative movement between the atom-cloud and the supporting platform, the finite atom cloud temperature, and the lateral movement of the atom cloud. We present the relevant feed-forward mitigation strategies for each identified non-ideality to neutralize the impact and obtain accurate acceleration measurements.

43 PARTICLE ACCELERATORS↗
DOE OSTI2020

Hawai‘i National Marine Renewable Energy Center (HINMREC)

The Hawaii National Marine Renewable Energy Center (HINMREC) was established to facilitate the commercialization of wave energy converter (WEC) devices, and to accelerate development and testing of Ocean Thermal Energy Conversion (OTEC) technologies. Housed at the Hawaii Natural Energy Institute (HNEI) of the University of Hawaii (UH), this program started with execution of the contract between the US Department of Energy (DOE) and UH in March 2009, and activities ran through the end of the project in September 2019. The DOE tasked HINMREC with facilitating and accelerating the build-out of the Navy’s Wave Energy Test Site (WETS), the nation’s first grid-connected open water wave energy conversion test facility, located off Marine Corps Base Hawaii (MCBH) in Kaneohe, on the island of Oahu. WETS was expanded from an existing test berth at 30m water depth to include test berths at 60m and 80m water depths. In recognition of the high costs associated with at-sea testing and evaluation of WEC devices, it was deemed imperative that HINMREC seek ways to reduce costs to developers by providing key research support to these early-stage technologies. WETS and HINMREC’s support allowed development of wave energy technology by providing a testing infrastructure that allows technology developers to test, demonstrate and evaluate their WEC devices, and generate data in order to advance WEC designs toward commercial readiness. HINMREC’s roles have included support in the establishment of the full site, including of wave resource characterization and site survey, followed by the essential roles of independent WEC device power performance assessment and environmental monitoring in support of deployed pre-commercial WECs. This DOE-funded work transitioned effectively to continue Navy-funded tasks for OTEC development, and activities at WETS, now under Naval Facilities Engineering Command (NAVFAC) funding. A secondary objective in the establishment of HINMREC was to assist the private sector in moving OTEC systems beyond proof-of-concept to pre-commercialization, primarily focused on system and component engineering, and local and global investigations into the potential environmental impacts of OTEC systems. HINMREC was tasked with maintaining high-resolution models of ocean thermal resources and the potential sustainable power output of OTEC systems. Ongoing tests begun previously under Navy funding at the OTEC Heat Exchangers (HXs) Test Facility at the Natural Energy Laboratory of Hawaii Authority (NELHA), in Kona on Hawaii Island, have been continued to identify cost-effective aluminum alloys for use in OTEC systems operating in the corrosive marine environment.

16 TIDAL AND WAVE POWER↗
DOE OSTI2021

Digital Twin Model for Advanced Manufacture of a Rotating Detonation Engine Injector

A digital twin material model (DTMM) of an additive manufacturing (AM) process was created to advance the state of the art in rotating detonation engine (RDE) injector design. Current RDE injectors are designed with large pressure drops, enabling a stable and repeatable combustion process. However, this comes at the cost of system efficiency. For the technology to transition to commercial fossil-based power generation, it is important to develop injectors with reduced flow losses. Low-loss injectors are difficult to design and manufacture with conventional manufacturing techniques. AM enables new design options, but the AM manufacturing process must be thoroughly understood to result in a robust design. A DTMM provides the necessary insight by defining the cause-effect relationships between process parameters, microstructure features, and properties. Therefore, a DTMM to support the design and manufacturing process was developed and applied to the design of a new additively manufactured low-loss injector. The injector combustion behavior was characterized through hot-fire tests, and mechanical performance was compared to the DTMM predictions. The two project goals were the successful development of the DTMM and the demonstration of an improved RDE injector design. The RDE injector design and DTMM developments occurred on parallel but dependent paths. The injector was designed to reduce pressure drop by increasing the cross-sectional flow area ratio between the injector air passages and the combustor annulus. This resulted in less structural material, raising the concern that thin members would be susceptible to high-cycle fatigue (HCF) under the periodic loading inherent to an RDE. It was most important for the DTMM to predict behavior in these features; therefore, the injector design concept guided the material thicknesses used in fatigue tests. The DTMM development started by manufacturing a series of coupons over the range of possible AM process variations. A design-of-experiment approach was used to select which process variable combinations gave the most efficient coverage relevant to the injector design space. The microstructure in each of these coupons was characterized, and then computational methods were used to create a numerical model of the correlation between process variables and microstructure. Next, a set of HCF samples were tested to calibrate existing models that map microstructure to HCF performance. Together, these two links formed the DTMM that calculates HCF behavior from AM process variables. Two injector prototypes were additively manufactured. The first injector design strategy aggressively pursued low-loss performance by substantially increasing the oxidizer flow area. The combination of manufacturing lead times and the fatigue testing schedule meant that the DTMM was not available when building this first prototype. Therefore, its process parameters were chosen based on a manual review of the available coupon data. This prototype was built successfully and evaluated in 58 combustion tests. Sustained detonation was achieved with remarkably reduced pressure loss, and some tests even displayed pressure loss characteristics similar to conventional gas turbine combustors. This achieved the project goal of improving RDE injector design. The second injector was manufactured according to the optimized parameters predicted by the DTMM. The flow area modifications of this injector were less aggressive than the first injector since demonstrating low pressure loss was not an objective of the second hot-fire test series. Rather, the test objective was to cause high cycle fatigue failure in the part due to periodic loading from the rotating detonation wave. The observed number of cycles to failure was to be compared to the number predicted by the DTMM and thereby assess the utility of the DTMM in component design. However, the required level of vibration was not obtained during combustion. Therefore, high cycle fatigue was not experienced in the hot-fire tests of the second injector. Fatigue data was obtained by further testing the second injector in a conventional HCF test apparatus. The injector demonstrated HCF strength above the DTMM prediction. In fact, it did not fail and testing was only discontinued due to reaching the end of the period of performance. This points to some success in the project’s primary goal of successfully developing and applying the DTMM to a component design. Implementing the DTMM recommendations for optimal processing parameters led to a part with acceptable properties. The DTMM was also shown to be an efficient correlator of data and to provide insight into the relationship between process settings, microstructure, and property performance. However, the failure of the DTMM prediction to match the experimental result of the injector fatigue test also points to the need to include significantly more data in the model development. In this project, coupons made with identical processing parameters exhibited drastically different properties from each other and from the injector part, which clearly influences the accuracy of a model that predicts performance based on parameters. Uncertainties in the build process must be quantified to develop more robust models. A denser and broader matrix of coupon process and geometry variations, several repeated builds of every point, more in-situ build process measurements, and direct observation of tensile and HCF sample microstructure (as opposed to separate microstructure specimens) are recommendations to improve future AM modeling efforts.

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2022

Low-Cost Preform and Molding Processes

The entry cost for prototyping a composite component for manufacture using automated, high rate processes is prohibitively expensive in many cases, especially for small business, where tooling costs may be several $100k. Discussions with industry also indicate that many small companies, tier 1 and 2 suppliers, have an interest to mold composite parts but do not want to deal with the capital cost, material handling issues, and labor associated with dry fiber preforming operations. While the molders may locate near the end user for logistics reasons, it may be more cost effective for the performer to remain regional and invest in capital equipment to support preform automation, thus keeping costs to a minimum. This project was designed to explore and demonstrate several options to meet these industry needs. Dry fiber preforming approaches were evaluated which allow for low pressure resin infusion, single sided tooling options such a vacuum assisted resin transfer molding (VARTM) or low pressure resin transfer molding (RTM-light). Unlike sheet molding compound, SMC compression molding where typical molding pressures of 1000 psi are required to push material into the desired location; positioning of a dry fiber preform into the desired location on the tool allows for low molding pressures of 10-50 psi. Lower molding pressures allow for use of low cost, additive fabrication of polymeric tooling. Polymeric tooling is suitable for rapid part prototyping and limited production. Dry fiber preforming approaches evaluated included use of commercial chopped strand mat, robotic chopper gun deposition, and continuous fiber preform augmentation using tailored fiber placement (TFP). Use of chopped strand mat does not require a robotic deposition method, however a cutting table is generally required and there is typically 20-30% scrap generation. While various fiber areal weights are available, the preform is not readily optimized for minimal fiber use or weight savings. In contrast, a robotic chopper gun approach allows for localized deposition where fiber is required to meet structural requirements. The robotic method is highly automated and minimizes fiber scrap, however the capital cost of the equipment and engineering labor for programming can result in higher preform cost compared to chopped strand mat in certain cases depending on preform complexity. Dry fiber preforming using the robotic chopper gun method allows for creation of three dimensional forms. This approach may be ideal for molding in-house, or if the preforms stack together densely to allow for efficient shipping. Applications evaluated for this program considered trade-off between fabrication of a fully 3D preform versus production of a flat preform which is designed to readily drape into the final desired shape. Such a preform design greatly simplifies robotic programming and requires no specialized tooling. The flat preforms are easily stacked and shipped to the final molding location. Flat preforms are much easier to augment with TFP continuous fiber to provide local reinforcement. The demonstration and evaluation of these preforming and tooling methods were completed on three component applications. The first application was a battery box cover for an electric vehicle which was highly three dimensional. The second demonstrator article was comprised of complex contours and was used to demonstrate the use of TFP and RTM-light molding process. The third demonstration article was the roof of an operator’s cab for large construction equipment. The roof is relatively flat however it is comprised of complex changes in thickness which clearly demonstrate the advantage of robotic chopper gun approach as compared to using numerous preform layers of chopped strand mat. The cost trades for the various preforming methods are summarized to help guide the reader as to preforming method considerations. Finally, these demonstrations all used glass fiber roving. A fourth, exploratory task was added to evaluate the ability to make preforms using Zoltek’s carbon fiber split tow roving. We were able to adapt the chopper gun to make flat preforms for laminate testing, but further development effort would be required to make suitable preforms.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Controlling Molecular Structure and Spin with Multiconfigurational Quantum Chemistry (Final Technical Report)

For many first-row transition metal complexes, structure-property relationships can be obtained from high-level molecular geometry optimizations and subsequent electronic structure studies. The project funded under this award utilized newly implemented fully internally contracted (FIC) nuclear gradients for extended multi-state (XMS) complete active space second-order multireference perturbation theory (CASPT2) to explore geometry changes in first-row transition metal coordination complexes. At the start of the project, only one full geometry optimization using FIC-CASPT2 analytical gradients had been reported (J. Chem. Theory Comput., 2016, 12 (8), 3781), and many open-questions regarding the performance and achievable accuracy in applying such computations to larger complexes persisted. Key deliverables in the report include the implementation of the numerical Hessian and subsequent vibrational analysis in the BAGEL program package. This includes both full Hessian vibrational analysis (FHVA) and a partial Hessian vibrational analysis (PHVA). The latter of which allows us to reduce the significant cost of computing the vibrational frequencies in a large molecule by focusing on the modes of highest interest. The gradient code also proved useful in the development of an approach to improve the Hubbard-U correction by removing bias in predicting spin-splitting in Fe(II) complexes via plane-wave density functional theory (DFT). Finally, we showed for three families of complexes (spin-crossover (SCO) complexes, metallocorroles complexes, and those with metal-metal bonds) that CASPT2 can result in good molecular geometries and established best practices in undertaking this work. We are now using this approach in collaborative projects with experimental groups, which would not have been possible at the start of this project. A common theme also arose through this work that static and dynamic correlation must be recovered in a balanced way to yield quantitative results. By systematically varying how both effects were included, we were able to make key chemical insights. This work supported the training of two postdoctoral scholars, one graduate student, and one undergraduate student in applying high-level wavefunction based methods to challenging systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Evaluation of the Turbine Integrated Mortality Reduction (TIMR SM ) Technology as a Smart Curtailment Approach (Final Summary Report)

Wind energy is a crucial technology for achieving net-zero emissions by 2050. However, the growth and deployment of wind energy in North America have led to the deaths of many bat species due to operating wind turbines. Hundreds of thousands of bats are estimated to die at wind turbines annually in North America. Operational minimization, which includes feathering turbine blades and curtailment, has been documented to reduce bat fatality effectively. Curtailment refers to altering turbine operation based on wind speed, time of year, temperature, sensors, and activity models. However, when turbines are curtailed, they do not generate power, resulting in energy loss and revenue for wind energy facilities. The Electric Power Research Institute (EPRI) funded the development of Turbine Integrated Mortality Reduction (TIM SM ) Technology, which curtails turbine operation when bats are detected. The initial TIMR system research showed promising results, with an 85% reduction in overall bat fatalities and a 91% reduction for the little brown bat. However, these results were based on a single site during one fall season, and it was unclear if similar results could be replicated at other wind energy facilities. This research aimed to validate the TIMR system results from the prior field study at a second site in the U.S., estimate the power production and reduction in bat mortality at turbines with installed TIMR systems relative to blanket curtailment and fully operational turbines, test the TIMR system in two calendar years and during the summer and fall periods, and evaluate the operational and commercial characteristics of the TIMR system for potential wind industry adoption. The study was conducted at a 500.9-MW wind energy facility in southeast Adair County, Iowa. Three experimental treatments were involved in this randomized block design study: TIMR, Curtailment at 5.0 m/s, and Normal Operation. In 2021, three treatments were used at 18 turbines, expanding to four treatments across 36 turbines in 2022. The TIMR system worked as designed throughout the entire study; however, because of unexpected wind turbine operational challenges in 2021, there was not sufficient sample size to evaluate the treatment differences. In 2022, there were significant differences in fatality levels between treatment types and normal operating turbines. Curtailment at 5.0 m/s reduced fatalities by 30.8% compared to normal operations, and TIMR decreased fatalities by 48.6% compared to normal operations. Two different methods were used to evaluate the differences in energy loss for each treatment. The TIMR system resulted in 1.3% to 1.6 % annual energy loss in 2021 and 1.0% to 1.2 % in 2022. The Curtailment at 5.0 m/s resulted in 0.6% to 0.8 % annual energy loss in 2021 and 0.5% to 0.6 % in 2022. The project achieved all the stated objectives and demonstrated that TIMR is an effective technology that balances bat fatality reduction with energy generation. The results will support the deployment of TIMR and other acoustic sensor-based technologies. The research provides valuable insights into the impact of different treatments on fatality rates and energy outputs, contributing to the ongoing efforts to mitigate the environmental impact of wind energy.

17 WIND ENERGY↗
DOE OSTI2025

Metadata Standards for the NSE: Core Fields

This standard presents a core set of metadata fields required for each managed digital object within the Nuclear Security Enterprise (NSE). Metadata standardization is a critical enabler for two primary objectives: 1) effectively sharing data, documents, and other digital objects between NSE sites; and 2) supporting digital engineering through the digital thread at the object level. Standardization is necessary for both schemas and vocabularies, meaning that both field standards and value standards must be specified. This document serves as a foundational field standard, recommending a core set of fields that should be uniformly required for all managed digital objects within the NSE.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2024

Magnesium Oxide Reduces Anxiety-like Behavior in Mice by Inhibiting Sulfate-Reducing Bacteria

The gut microbiota–brain axis allows for bidirectional communication between the microbes in our gastrointestinal (GI) tract and the central nervous system. Psychological stress has been known to disrupt the gut microbiome (dysbiosis) leading to anxiety-like behavior. Pathogens administered into the gut have been reported to cause anxiety. Whether commensal bacteria affect the gut–brain axis is not well understood. In this study, we examined the impact of a commensal sulfate-reducing bacteria (SRB) and its metabolite, hydrogen sulfide (H2S), on anxiety-like behavior. We found that mice gavaged with SRB had increased anxiety-like behavior as measured by the open field test. We also tested the effects of magnesium oxide (MgO) on SRB growth both in vitro and in vivo using a water avoidance stress (WAS) model. We found that MgO inhibited SRB growth and H2S production in a dose-dependent fashion. Mice that underwent psychological stress using the WAS model were observed to have an overgrowth (bloom) of SRB (Deferribacterota) and increased anxiety-like behavior. However, WAS-induced overgrowth of SRB and anxiety-like behavioral effects were attenuated in animals fed a MgO-enriched diet. These findings supported a potential MgO-reversible relationship between WAS-induced SRB blooms and anxiety-like behavior.

60 APPLIED LIFE SCIENCES↗