Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strength”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Dynamic tensile strength of lunar rock types

The dynamic tensile strength of four rocks are determined. A flat plate impact experiment is employed to generate approximately one-microsecond-duration tensile stress pulses in rock samples by superposing rarefaction waves to induce fracture. It is noted that the effect of chemical weathering and other factors has not been explicitly studied. The given tensile strengths are based on a series of experiments on each rock where determination of incipient spallation is made by terminal microscopic examination. The data are generally consistent with previous determinations, at least one of which was for a significantly chemically altered but physically coherent rock.

Cohn, S. N.↗
NASA NTRS1981

Observationally determined silicon II oscillator strengths

Si II oscillator strengths for eight resonance lines from the ground state have been determined using a curve-of-growth analysis of interstellar data from the Copernicus and International Ultraviolet Explorer satellites. The oscillator strengths for 1526 A and 1808 A increase by factors of 3.0 and 1.5, respectively, from previously tabulated values; those for 989 A and 1020 A decrease by factors of 0.55 and 0.60, respectively. These new values result in better silicon abundances for interstellar clouds and resolve a long-standing puzzle in the interpretation of quasar absorption line data.

Shull, J. M.↗
NASA NTRS1980

Properties of PMR polyimide composites made with improved high strength graphite fibers

Recent graphite fiber developments have resulted in high strength, intermediate modulus graphite fibers having improved thermo-oxidative resistance. These improved fibers, obtained from various commercial suppliers, were used to fabricate PMR-15 and PMR-11 polyimide composites. Studies were performed to investigate the effects of the improved high strength graphite fibers on composite properties after exposure in air at 600 F. The use of the more oxidatively resistant fibers did not result in improved performance at 600 F. Two of the improved fibers were found to have an adverse effect on the long-term performance of PMR composites. The influence of various factors such as fiber physical properties, surface morphology and chemical composition are also discussed.

Vannucci, R. D.↗
NASA NTRS1981

Anomalous C-12H4:C-13H4 strengths in 3 ny sub 3

The C-12:C-13 ratios in the atmospheres of the outer planets are important parameters with which to test models for isotope formation and fractionation during the early history of the solar system, yielding insight into processes occurring in the primitive solar nebula. The 3 ny sub 3 spectra of methane were obtained using the Kitt Peak Solar Fourier Transform Spectrometer and a 6 m White cell. The experimental results are summarized in a table. The strength ratios for the R-branch of 3 ny sub 3 exhibit strong anomalies, with C-13H4 lines consistently weaker than their C-12H4 counterparts. The C-12:C-13 abundance ratios for the atmospheres of Jupiter and Saturn have been redetermined using the 3 ny sub 3 line-strength ratios measured.

Brault, J. W.↗
NASA NTRS1980

Thermomechanical processing of Haynes alloy No. 188 sheet to improve creep strength

A study has been carried out with the objective of improving the low-strain creep strength of thin gauge (0.38 mm) sheet of Haynes alloy No. 188, a candidate material for the heat shields of advanced reentry and hypersonic vehicles. It is found that significant improvements in the low-strain creep strength are obtained in sheets with a strong recrystallized texture produced by a thermomechanical treatment. The optimum results are achieved after 80% final coldwork followed by a 10-min anneal at 1505 K.

Klarstrom, D. L.↗
NASA NTRS1982

Factors influencing the thermally-induced strength degradation of B/Al composites

Literature data related to the thermally-induced strength degradation of B/Al composites were examined in the light of fracture theories based on reaction-controlled fiber weakening. Under the assumption of a parabolic time-dependent growth for the interfacial reaction product, a Griffith-type fracture model was found to yield simple equations whose predictions were in good agreement with data for boron fiber average strength and for B/Al axial fracture strain. The only variables in these equations were the time and temperature of the thermal exposure and an empirical factor related to fiber surface smoothness prior to composite consolidation. Such variables as fiber diameter and aluminum alloy composition were found to have little influence. The basic and practical implications of the fracture model equations are discussed.

Dicarlo, J. A.↗
NASA NTRS1981

Strength integrity of the Space Shuttle Orbiter tiles

The development of the thermal protection system (TPS) for shielding the Shuttle from high temperature aerodynamic heating during atmospheric entry is described. The TPS was required to limit structural heating to 350 F, be used for 100 flights, withstand temperature ranges from -250 to 2800 F, attach to an aluminum structure, and provide the aerodynamic moldline. More than 30,000 tiles of individual size, shape, and strength were bonded adhesively to a Nomex felt mat which coated critical areas of the craft. Densification processes for strengthening the tiles in highly loaded areas are outlined and stress sources for each mission phase are analyzed. Aerodynamic, acoustic, combined loads, and verification tests for stress levels up to 125% of nominal were performed for each tile. The one complete and 15 partial tiles lost during the initial flight were all lower strength, undensified tiles.

Moser, T. L.↗
NASA NTRS1981

Impact cratering - The effect of crustal strength and planetary gravity

The effect of varying planetary crustal strength and surface gravity on the depth of impact craters is investigated, by coupling the results of compressible flow, finite difference calculations carried out to stress levels below the compressional dynamic yield point, in keeping with the incompressible fluid flow model of Maxwell (1973). The fundamental assumption in this description is that the amplitude of the particle velocity field decreases with time as kinetic energy is converted into heat and gravitational potential energy. By using a Mohr-Coulomb yield criterion, the effect of varying strength on transient crater depth and on crater formation time in the gravity field of the moon is investigated for the case of 5 km/sec impactors having radii in the 10 to 10 to the 7th cm range.

Okeefe, J. D.↗
NASA NTRS1981

The failure strengths of perfect diamond crystals

Finite elasticity analysis is extended to the 110 direction, where off axis strain symmetry is not present, and the third order elastic data are obtained for diamond. The compressive yield strengths of perfect diamond crystals loaded in the 100, 110, and 111 directions are predicted to be 2.2, 5.6, and 2.8 Mbars, respectively, while the corresponding tensile fracture strengths are 1.0, 0.5, and 0.5 Mbars. From these results and from Hertz theory it is predicted that ring fracture of spherically tipped diamonds pressed against a flat will occur at pressures of 1.8-1.9 Mbars, substantially below the yield pressure (above 3 Mbars). Modification of the tip shape leads to a predicted increase in the pressure at which fracture occurs.

Whitlock, J.↗
NASA NTRS1982

Theoretical oscillator strengths for 21 spin-forbidden lines of C, N, O, Al, and Si

Detailed calculations are reported of the oscillator strengths of 21 spin-forbidden lines of C II, C III, N I, N II, N III, O I, O II, Al II, and Si III, including 10 lines arising from seven ground levels. All 21 lines lie in the region from 1160 to 2670 A, and the oscillator strengths probably are accurate typically to + or - 50%. These weak lines are particularly important in determining accurate elemental abundances in the interstellar gas.

Cowan, R. D.↗
NASA NTRS1982

Effect of space flight on bone strength

To test the possibility that spaceflight has a deleterious effect on bone mechanical properties, femur breaking strength by torsional loading in rats that had been flown for 19 days aboard Cosmos 936 was determined. The results showed that femurs from flight rats were less stiff than the flight controls, and failed under torsion at a lower torque and energy of absorption. The defect was corrected following space flight and could be prevented during space flight by centrifuging the rats at 1 x g. Altered bone geometry due to inhibition of bone formation at the periosteal surface provides the most likely explanation for the decrease in bone strength during spaceflight.

Spengler, D. M.↗
NASA NTRS1982

Strength and Mechanics of Bonded Scarf Joints for Repair of Composite Materials

Experimental and analytical investigations of scarf joints indicate that slight bluntness of adherend tips induces adhesive stress concentrations which significantly reduce joint strength, and the stress distribution through the adhesive thickness is non-uniform and has significant stress concentrations at the ends of the joint. The laminate stacking sequence can have important effects on the adhesive stress distribution. A significant improvement in joint strength is possible by increasing overlap at the expense of raising the repair slightly above the original surface. Although a surface grinder was used to make most experimental specimens, a hand held rotary bur can make a surprisingly good scarf. Scarf joints wit doublers on one side, such as might be used for repair, bend under tensile loads and may actually be weaker than joints without doublers.

Pipes, R. B.↗
NASA NTRS1982

Theoretical Model of the Effect of Crack Tip Blunting on the Ultimate Tensile Strength of Welds in 2219-T87 Aluminum

A theoretical model representing blunting of a crack tip radius through diffusion of vacancies is presented. The model serves as the basis for a computer program which calculates changes, due to successive weld heat passes, in the ultimate tensile strength of 2219-T81 aluminum. In order for the model to yield changes of the same order in the ultimate tensile strength as that observed experimentally, a crack tip radius of the order of .001 microns is required. Such sharp cracks could arise in the fusion zone of a weld from shrinkage cavities or decohered phase boundaries between dendrites and the eutectic phase, or, possibly, from plastic deformation due to thermal stresses encountered during the welding process. Microstructural observations up to X2000 (resolution of about .1 micron) did not, in the fusion zone, show structural details which changed significantly under the influence of a heat pass, with the exception of possible small changes in the configuration of the interdendritic eutectic and in porosity build-up in the remelt zone.

Beil, R. J.↗
NASA NTRS1982

Structural application of high strength, high temperature ceramics

The operation of rocket engine turbine pumps is limited by the temperature restrictions of metallic components used in the systems. Mechanical strength and stability of these metallic components decrease drastically at elevated temperatures. Ceramic materials that retain high strength at high temperatures appear to be a feasible alternate material for use in the hot end of the turbopumps. This project identified and defined the processing parameters that affected the properties of Si3N4, one of candidate ceramic materials. Apparatus was assembled and put into operation to hot press Si3N4 powders into bulk material for in house evaluation. A work statement was completed to seek outside contract services to design, manufacture, and evaluate Si3N4 components in the service environments that exists in SSME turbopumps.

Hall, W. B.↗
NASA NTRS1983

NDE detectability of fatigue type cracks in high strength alloys

Specimens suitable for investigating the reliability of production nondestructive evaluation (NDE) to detect tightly closed fatigue cracks in high strength alloys representative of those materials used in spacecraft engine/booster construction were produced. Inconel 718 was selected as representative of nickel base alloys and Haynes 188 was selected as representative of cobalt base alloys used in this application. Cleaning procedures were developed to insure the reusability of the test specimens and a flaw detection reliability assessment of the fluorescent penetrant inspection method was performed using the test specimens produced to characterize their use for future reliability assessments and to provide additional NDE flaw detection reliability data for high strength alloys. The statistical analysis of the fluorescent penetrant inspection data was performed to determine the detection reliabilities for each inspection at a 90% probability/95% confidence level.

Christner, B. K.↗
NASA NTRS1982

Hybrid optimization of truss structures with strength and buckling constraints

An efficient scheme utilizing standard nonlinear programming methodology is presented for the optimal design of elastic, redundant structures with strength and buckling constraints. Numerical examples are given which demonstrate how this method, involving a constraint redefinition, can successfully overcome certain problems typical to such structures. The scheme is applied to the design of a cantilever truss with strength and buckling constraints, in which optimal nonuniform cross section columns are used for all elements critical in buckling. It is found that permitting node movement and adding redundancies can lower the weight of the structure for the prescribed design constraints. In addition, the node excursions in this configuration are shown to be relatively small.

Hajela, P.↗