SEARCH · Engineering Papers

Results for “power system simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

All sources NASA NTRS DOE OSTI

NASA NTRS2020

An Evaluation of UAS Pilot Workload and Acceptability Ratings with Four Simulated Radar Declaration Ranges

Currently, minimum operational performance standards (MOPS) are being developed for a broader range of unmanned aircraft system (UAS) platforms, including smaller UAS that will feature onboard sensors that are low in size, weight, and power, otherwise known as low SWaP. The low SWaP sensors used to detect non-cooperative traffic will have limited declaration ranges compared to those designed for medium-to-large UAS. A human-in-the-loop (HITL) study was conducted examining four possible radar declaration ranges (i.e., 1.5 NM, 2 NM, 2.5 NM, and 3 NM) for a potential low SWaP sensor with a detect and avoid (DAA) system encountering various non-cooperative encounters in Oakland Center airspace. Participants had lower workload, particularly workload associated with temporal demand and effort, in scenarios that featured larger declaration ranges. Furthermore, participants reported better ability to remain DAA well clear within the larger declaration range conditions, specifically with the 2.5 NM and 3 NM conditions.

UAS↗

NASA NTRSDate not supplied

Exploring Quantum State Preparation Using Tensor Networks and Sparse Wavefunction Simulations

The variational quantum eigenvalue solver is a powerful hybrid quantum-classical approach that has been suggested as a candidate method to run on near-term quantum hardware for computing ground state electronic energies of molecular systems. However, even for small molecules, the number of variational parameters and qubits required to minimize the electronic energy is beyond the reach of current quantum computers except for small basis sets. We explore a new paradigm for state preparation where we test how much of the optimization can be approximately prepared with classical computers to reduce the number of optimization steps performed using a quantum device. By adapting a recent algorithm for the factorized form of the UCC ansatz, we can study molecular electronic structure problems with up to 64 qubits. In addition, we also test a related approach of using tensor networks to optimize quantum circuits in order to benchmark various lattice models. We present results using these approaches and discuss strategies for incorporating these ideas into variational algorithms involving near-term quantum computers. Our results help demonstrate the strength of the UCC ansatz and address pressing questions about optimal initial parameterizations and circuit construction.

quantum computing↗

NASA NTRS1994

Overview of space power electronic's technology under the CSTI High Capacity Power Program

The Civilian Space Technology Initiative (CSTI) is a NASA Program targeted at the development of specific technologies in the areas of transportation, operations and science. Each of these three areas consists of major elements and one of the operation's elements is the High Capacity Power element. The goal of this element is to develop the technology base needed to meet the long duration, high capacity power requirements for future NASA initiatives. The High Capacity Power element is broken down into several subelements that includes energy conversion in the areas of the free piston Stirling power converter and thermoelectrics, thermal management, power management, system diagnostics, and environmental compatibility and system's lifetime. A recent overview of the CSTI High capacity Power element and a description of each of the program's subelements is given by Winter (1989). The goals of the Power Management subelement are twofold. The first is to develop, test, and demonstrate high temperature, radiation-resistant power and control components and circuits that will be needed in the Power Conditioning, Control and Transmission (PCCT) subsystem of a space nuclear power system. The results obtained under this goal will also be applicable to the instrumentation and control subsystem of a space nuclear reactor. These components and circuits must perform reliably for lifetimes of 7-10 years. The second goal is to develop analytical models for use in computer simulations of candidate PCCT subsystems. Circuits which will be required for a specific PCCT subsystem will be designed and built to demonstrate their performance and, also, to validate the analytical models and simulations. The tasks under the Power Management subelement will now be described in terms of objectives, approach and present status of work.

Schwarze, Gene E.↗

NASA NTRS2023

Modeling Turboshaft Engines for the Revolutionary Vertical Lift Technology Project, Expanded

Turboshaft engine performance and weight models were developed to support conceptual propulsion and vehicle mission design and performance under the Revolutionary Vertical Lift Technology (RVLT) Project in 2019 by Snyder in Reference 7. These models were developed using open data sources, assuming present and future technology levels, and range from 650 to 5,000 output shaft horsepower (485 to 3,730 kW). This paper expands on the previous research, extending the power ranges from 200 to 15000 output shaft horsepower (150 to 11,200 kW) and documenting the methodology, assumptions, and engine performance realizes important benefits for NASA and the aviation community. NASA concept-vehicle study efforts using these baseline propulsion models can be more readily shared among the government, industry, and university community to support present and future work. Assessing the benefits of advanced technologies and new configurations can be facilitated using these models, which helps guide technology investment. As the various conceptual vehicle and mission analysis simulations are developed, these models can be used directly for broader systems analysis studies, including optimization within the propulsion model itself. To expand on the previous effort, the turboshaft engine is briefly discussed, highlighting the specific components, and expected performance characteristics over the updated power range and technology levels considered. Additional engine configurations will also be discussed as they vary based on power output and assumed technology level. Engine performance, such as airflow, power output and weight are updated, noting important trends for system studies. Finally, the effect of advanced propulsion technologies on public reference models including RVLT concept vehicles are reported along with the tools and software methods used to complete the analysis.

VTOL↗

NASA NTRS1972

Drive turbine systems for 20-inch turbofan simulators. 1: Duct turbine design

A study was made to evolve the turbine drive systems for 20-inch turbofan engine simulators. The fan designs used in the simulators included single-stage and two-stage configurations that covered a wide range of rotative speed and power requirement. The objective assumed for the study was to evolve one core turbine design that could drive all of the single-stage fans and, when operated in combination with one duct turbine design, drive all of the two-stage fans. The duct turbine power output is then needed to determine the make-up power required of the core turbine over the range of two-stage fan operating conditions. The duct turbine design analysis is reported and includes the selection of the duct turbine velocity diagram, a description of the blade design, and a determination of its off-design performance. Adjustable stators were found to be quite advantageous to the duct turbine off-design operation. The use of adjustable stators enabled the duct turbine to accommodate fan mass flow at all operating points and caused the duct turbine power output to increase as the total power requirement increased. This in turn resulted in a core turbine make-up power requirement that was not significantly greater than that required for driving the single-stage fans.

Whitney, W. J.↗

NASA NTRS1973

Results of solar electric thrust vector control system design, development and tests

Efforts to develop and test a thrust vector control system TVCS for a solar-energy-powered ion engine array are described. The results of solar electric propulsion system technology (SEPST) III real-time tests of present versions of TVCS hardware in combination with computer-simulated attitude dynamics of a solar electric multi-mission spacecraft (SEMMS) Phase A-type spacecraft configuration are summarized. Work on an improved solar electric TVCS, based on the use of a state estimator, is described. SEPST III tests of TVCS hardware have generally proved successful and dynamic response of the system is close to predictions. It appears that, if TVCS electronic hardware can be effectively replaced by control computer software, a significant advantage in control capability and flexibility can be gained in future developmental testing, with practical implications for flight systems as well. Finally, it is concluded from computer simulations that TVCS stabilization using rate estimation promises a substantial performance improvement over the present design.

Fleischer, G. E.↗

NASA NTRS1973

Electrical properties of dry rocks

The mechanism by which atmospheric moisture affects the conductivity and dielectric constant of rock specimens was studied in time and frequency domains. It is suggested that adsorbed water molecules alter the surface conductivity in a manner similar to that observed in semiconductors and insulators. Powdered basalts show a low-frequency dispersion produced by the atmospheric moisture remaining in the pore system of the sample in a high vacuum; this effect is attributed to isolated adsorption centers. Simulated lunar permafrost at 100 K and a vacuum of 10 to the -8th power torr together with data on lunar samples contaminated with atmospheric moisture and the dielectric properties of ice at various temperatures indicate that, if permafrost exists in the moon it should present a relaxation peak at approximately 300 Hz; for temperatures up to 263 K it may go up to 20 KHz. It is concluded that in order to have electrical steady state conditions in rock samples it is necessary to have volume charge accumulations at interfaces within the sample and at the electrode sample interface. A method for measuring heterogeneous dielectrics with non-negligible ohmic and dielectric conductivities is proposed and experimentally verified.

Morrison, H.↗

NASA NTRS1977

A nickel-cadmium battery reconditioning circuit

The circuit presented is simple and small enough to be included in a typical battery charge/power control assembly, yet provides the advantage of a complete ground-type battery reconditioning discharge. Test results on the circuit when used to recondition two 24 cell, 20 A-h nickel-cadmium batteries are given. These results show that a battery reconditioned with this circuit returns to greater than 90 percent of its original capacity (greater than nameplate capacity) and follows a typical new battery degradation curve even after over 20,000 simulated orbital cycles for a 4 year period. Applications of the circuit are considered along with recommendations relative to its use. Its application in low voltage (22 to 36 Vdc) power systems and in high voltage (100 to 150 Vdc) power systems is discussed. The implications are that the high voltage systems have a greater need for battery reconditioning than their low voltage counterparts, and that using these circuit techniques, the expected life of a battery in low Earth orbit can be up to 5 years.

Lanier, R.↗

NASA NTRS1977

The helical screw expander evaluation project

A positive-displacement helical-screw expander of the Lysholm type has been adapted for geothermal service and successfully demonstrated in a 50 kW prototype power system. Evaluation of the expander by tests of a new model in a 1 MW power system under wellhead conditions in selected liquid-dominated geothermal fields is proposed. The objectives are to determine the performance characteristics of the expander and power system over a broad range of operating conditions and also to examine the concept of wellhead power plants. Throttling and fractionation of the fluids from the test wells is planned to simulate a wide range of wellhead pressures and steam fractions. Variation in the expander exhaust pressure is also planned. The investigation will include expander efficiency, corrosion, erosion, scale formation and control, and endurance testing. Interaction studies with the wells and an electric grid are also proposed.

Mckay, R. A.↗

NASA NTRS1979

Alternative Beam Efficiency Calculations for a Large-aperture Multiple-frequency Microwave Radiometer (LAMMR)

The fundamental definition of beam efficiency, given in terms of a far field radiation pattern, was used to develop alternative definitions which improve accuracy, reduce the amount of calculation required, and isolate the separate factors composing beam efficiency. Well-known definitions of aperture efficiency were introduced successively to simplify the denominator of the fundamental definition. The superposition of complex vector spillover and backscattered fields was examined, and beam efficiency analysis in terms of power patterns was carried out. An extension from single to dual reflector geometries was included. It is noted that the alternative definitions are advantageous in the mathematical simulation of a radiometer system, and are not intended for the measurements discipline where fields have merged and therefore lost their identity.

Schmidt, R. F.↗

NASA NTRS1981

Description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory test model

A description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory model is presented. The AMCD is a momentum exchange device which is under development as an advanced control effector for spacecraft attitude control systems. The digital computer simulation of this device incorporates the following models: six degree of freedom rigid body dynamics; rim warp; controller dynamics; nonlinear distributed element axial bearings; as well as power driver and power supply current limits. An annotated FORTRAN IV source code listing of the computer program is included.

Woolley, C. T.↗

NASA NTRS1987

High temperature metal matrix composites for future aerospace systems

Research was conducted on metal matrix composites and intermetallic matrix composites to understand their behavior under anticipated future operating conditions envisioned for aerospace power and propulsion systems of the 21st century. Extremes in environmental conditions, high temperature, long operating lives, and cyclic conditions dictate that the test evaluations not only include laboratory testing, but simulated flight conditions. The various processing techniques employed to fabricate composites are discussed along with the basic research underway to understand the behavior of high temperature composites, and the relationship of this research to future aerospace systems.

Stephens, Joseph R.↗

NASA NTRS1988

High temperature metal matrix composites for future aerospace systems

Stephens, Joseph R.↗

NASA NTRS1991

HyperCLIPS

Integration of CLIPS computer program into HyperCard computer program combines intuitive, interactive user interface of MacIntosh computer with powerful symbolic computation of expert-system interpreter. HyperCard provides excellent programming environment for quickly developing front end of application program with buttons, dialogs, and pictures, while CLIPS interpreter provides powerful inference engine for analysis and solution of complicated problems. Advantages of both packages available for wide range of uses: rapid prototyping of knowledge-based expert-systems software, interactive simulations of physical systems, and intelligent control of hypertext processes. Written in C language and Pascal.

Hill, Randall W., Jr.↗

NASA NTRS1990

One- and two-dimensional Stirling machine simulation using experimentally generated flow turbulence models

Investigations of one- and two-dimensional (1- or 2-D) simulations of Stirling machines centered around experimental data generated by the U. of Minnesota Mechanical Engineering Test Rig (METR) are covered. This rig was used to investigate oscillating flows about a zero mean with emphasis on laminar/turbulent flow transitions in tubes. The Space Power Demonstrator Engine (SPDE) and in particular, its heater, were the subjects of the simulations. The heater was treated as a 1- or 2-D entity in an otherwise 1-D system. The 2-D flow effects impacted the transient flow predictions in the heater itself but did not have a major impact on overall system performance. Information propagation effects may be a significant issue in the simulation (if not the performance) of high-frequency, high-pressure Stirling machines. This was investigated further by comparing a simulation against an experimentally validated analytic solution for the fluid dynamics of a transmission line. The applicability of the pressure-linking algorithm for compressible flows may be limited by characteristic number (defined as flow path information traverses per cycle); this warrants further study. Lastly the METR was simulated in 1- and 2-D. A two-parameter k-w foldback function turbulence model was developed and tested against a limited set of METR experimental data.

Goldberg, Louis F.↗

NASA NTRS1992

A Zero-Gyro safemode controller for HST

The purpose of this paper is to document the Zero-Gyro Sunpoint mode for Hubble Space Telescope, a safemode designed to ensure a power positive state without the use of rate gyros. This paper presents an overview of the Zero-Gyro Sunpoint algorithm, followed by details of the algorithm, control system design, and simulation results. A new, related safemode test, the System Momentum Test, is also discussed.

Markley, F. L.↗

NASA NTRS1993

A parallel adaptive mesh refinement algorithm

Over recent years, Adaptive Mesh Refinement (AMR) algorithms which dynamically match the local resolution of the computational grid to the numerical solution being sought have emerged as powerful tools for solving problems that contain disparate length and time scales. In particular, several workers have demonstrated the effectiveness of employing an adaptive, block-structured hierarchical grid system for simulations of complex shock wave phenomena. Unfortunately, from the parallel algorithm developer's viewpoint, this class of scheme is quite involved; these schemes cannot be distilled down to a small kernel upon which various parallelizing strategies may be tested. However, because of their block-structured nature such schemes are inherently parallel, so all is not lost. In this paper we describe the method by which Quirk's AMR algorithm has been parallelized. This method is built upon just a few simple message passing routines and so it may be implemented across a broad class of MIMD machines. Moreover, the method of parallelization is such that the original serial code is left virtually intact, and so we are left with just a single product to support. The importance of this fact should not be underestimated given the size and complexity of the original algorithm.

Quirk, James J.↗

NASA NTRS1995

Simulation model of the integrated flight/propulsion control system, displays, and propulsion system for ASTOVL lift-fan aircraft

A simulation model has been developed for use in piloted evaluations of takeoff, transition, hover, and landing characteristics of an advanced, short takeoff, vertical landing lift fan fighter aircraft. The flight/propulsion control system includes modes for several response types which are coupled to the aircraft's aerodynamic and propulsion system effectors through a control selector tailored to the lift fan propulsion system. Head-up display modes for approach and hover, tailored to their corresponding control modes are provided in the simulation. Propulsion system components modeled include a remote lift and a lift/cruise engine. Their static performance and dynamic response are represented by the model. A separate report describes the subsonic, power-off aerodynamics and jet induced aerodynamics in hover and forward flight, including ground effects.

Chung, W. Y. William↗