Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “potential yield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Application of future remote sensing systems to irrigation

Area estimates of irrigated crops and knowledge of crop type are required for modeling water consumption to assist farmers, rangers, and agricultural consultants in scheduling irrigation for distributed management of crop yields. Information on canopy physiology and soil moisture status on a spatial basis is potentially available from remote sensors, so the questions to be addressed relate to: (1) timing (data frequency, instantaneous and integrated measurement); and scheduling (widely distributed spatial demands); (2) spatial resolution; (3) radiometric and geometric accuracy and geoencoding; and (4) information/data distribution. This latter should be overnight, with no central storage, onsite capture, and low cost.

Miller, L. D.↗
NASA NTRS1983

An ab initio study of core-valence correlation

Especially in the cases of the first two columns of the periodic table, the inclusion of core-valence correlation in ab initio CI calculations yields a contraction of the atomic valence shell and improves both calculated atomic ionization potentials and atomic energy separations. For the alkali dimers Na2, K2, and Rb2, the presently calculated bond lengths are in excellent agreement with experiments when core-valence is included. In addition, the valence dissociation energies are accurate.

Partridge, H.↗
NASA NTRS1987

Electrical potential measurements in the lower atmosphere

Lower-atmospheric potential measurements obtained in 1983 through 1985 using the Hy-wire technique are summarized in this paper. Observed values of the potential were in the range of 50-100 kV in Fairbanks, AK, compared with 100-200 kV at Wallops Island, VA. When one-hour averages are formed from the entire data set the result is a unitary variation very reminiscent of both the Carnegie curve and more recent stratospheric electric field data. A comparison with an aircraft potential measurement in the same vicinity during April 1983 demonstrates that the two techniques yield roughly similar results, except that the Hy-wire measurements were 20-30 percent lower in absolute value.

Woosley, J. D.↗
NASA NTRS1990

Multipole radiation in charged-particle scattering

This paper formulates the general problem of photon emission in particle scattering using a classical and quantum mechanical approach. The connection between the classical short collision time (SCT) and Born results is examined for various special classifications of problems. In the dipole case the two formulations yield results that can be expressed in the same form and for arbitrary scattering potential. For quadrupole emission the SCT and Born results are the same only for a short-range potential, however. The quadrupole problem is more sensitive to details in the process because the calculation requires an expansion of the total amplitude for the process to lowest order in the photon wave number or momentum. The special case of photon emission associated with spin-flip transitions during scattering is considered for spin-1/2 particles. Like classical magnetic dipole radiation, there is no infrared divergence feature for this type of emission.

Gould, Robert J.↗
NASA NTRS1994

On the effects of filtering on convective-core statistics

Analysis of convective events north of Australia during the equatorial Monsoon Experiment (EMEX) reinforces accumulating evidence that convective cores over the tropical ocean are weak, with small diameters and vertical velocities. Superposition of smaller-scale turbulence on the convective core signal could yield artificially small cores, and thus produce sampling bias by aircraft. To investigate this potential source of bias, a side-by-side analysis of filtered and unfiltered vertical velocity data was performed while investigating the EMEX convective cores. Data were collected by the NOAA P3 and NCAR Electra using filtered (Graham filter) and non-filtered cores. The effects of filtering vertical velocity data to identify updraft and downdraft cores were noticeable but smaller than expected. Updraft cores had a vertical velocity greater than 1 m/sec for at least 500 m, and downdraft cores were defined analogously so that the filter eliminated events with less than a 500 m apparent diameter. Median and 10 percent core diameters were increased by 20-25 percent at most, with larger increases at higher levels (fewer small events). The maximum vertical velocity was changed only by changing the individual events in the distribution, but changes were detectable. At the lower levels, where many small, weak cores are introduced by filtering, average vertical velocity for the updraft cores was lowered by up to around 10 percent. Mass flux was changed the least, since diameter and mean vertical velocity respond to filtering in opposite ways. The filtering procedure increased total mass flux slightly due to inclusion of more upward moving air into the sample.

Lemone, Margaret A.↗
NASA NTRS1999

A Heuristic Approach to Examining Volatile Equilibrium at Titan's Surface

R. D. Lorenz, J. I. Lunine, and C. P. McKay have shown in a manuscript accepted for publication that, for a given ethane abundance and surface temperature, the nitrogen and methane abundances in Titan's atmosphere can be calculated, yielding a surface pressure that can be compared with the observed value. This is potentially a very valuable tool for examining the evolution of Titan's climatology. Its validity does depend on two important assumptions, however: 1) that the atmosphere of Titan is in global radiative equilibrium, and 2) that volatiles present are in vapor equilibrium with the surface. The former assumption has been shown to be likely, but the latter has not. Water vapor in the Earth's atmosphere, in fact, is generally not very close to equilibrium in a global sense. In the present work a heuristic approach is used to examine the likelihood that methane vapor is in equilibrium with Titan's surface. Plausible climate scenerios are examined that are consistent with methane vapor abundances derived from Voyager IRIS data. Simple precipitation and surface diffusion models are incorporated into the analysis. It is tentatively inferred that methane may be in surface equilibrium near the poles, but that equilibrium at low latitudes is more difficult to establish.

Samuelson, Robert E.↗
NASA NTRS2006

Plasma Characteristics Measured in the Plume of a NEXT Multi-Thruster Array

Plasma properties in the plume produced by a 3+1 NEXT thruster array operating at full power were mapped using a series of planar Langmuir probes. The Langmuir probes were swept across the diameters of each thruster as well as the centerline of the array at multiple downstream axial locations to produce a plasma map of the plume produced by the array. Such maps yielded the spatial distribution of the plasma density, the electron temperature and the plasma potential in the near field of the array. This spatial information provides insight into local plasma particle flow. Flow direction is particularly important from both an array lifetime and spacecraft-plume plasma interaction standpoint. The variation in the plume plasma parameters tended to vary in a manner consistent with both plume shape and overlap of adjacent plumes.

Foster, John E.↗
NASA NTRS2019

Crop Readiness Level (CRL): A Scale to Track Progression of Crop Testing for Space

The development of engineering technologies and hardware for aerospace applications is often tracked on a 1-9 scale of readiness or TRL, with a "1" representing very basic or fundamental principles, and a "9" being flight tested, functional hardware. Preparing to grow crops for supplemental food and eventual life support contributions on space missions faces similar challenges. Nearly 20 years ago, the concept of a "crop readiness level" was suggested at a bioregenerative life support conference held at Kennedy Space Center, but there was little follow up to this. We propose to revive this concept to track the preparation and testing of different crop species for eventual use in the unique environment of space. For the sake of uniformity, we recommend a 1-9 scale, with a "1" being just the identification of a potential crop, followed by some basic horticultural testing, cultivars trials, then testing growth and yield under various controlled environments, progression to more space-like environments and hardware, understanding the nutritional, organoleptic, and food safety aspects of the crop, initial testing in space, and a final stage of growing the crop for food in space ("9"). We attempted to make the scaling logical and progressive, but our main goal is to initiate a dialogue in the space, plant research community to develop a scale for assessing crop readiness.

Romeyn, M. W.↗
DOE OSTI2021

Evaluating Safeguards Statistical Assumptions via Stochastic Simulation

Herein, the authors built and tested a stochastic simulation to estimate achieved detection probabilities (DPs) on a stratum basis, over a tailorable range of diverted amounts from 0 to 2 SQ, using typical IAEA inspection data: i.e., SQ in stratum, number of items, number of gross/partial/bias defect measurements conducted, and realistic relative standard deviation (RSD) values for typical IAEA verification measurements. For bulk strata, the model calculates achieved DP at 0.01 SQ diversion increments; for item strata, the model calculates DP using the smallest realistic diversion increment (e.g., a plate, pin, or coupon). After successfully benchmarking against IAEA deterministic models, the simulation was used to test the sensitivity of DP to certain standard assumptions and selected input parameters. First, the equal defect assumption was tested; the results suggest significant complexity in the effectiveness of partial defect measurements. Next, the authors explored the sensitivity of DP to the assumed RSD of attribute tests. Then, the authors compared non-normal models for instrument performance (e.g., logistic, step, or arbitrary functions) to the typical results from a normal distribution (characterized by RSD). This last comparison was supplemented with experimentally derived performance data for an HM-5. The HM-5 was used to make enrichment measurements on both LEU and HEU MTR fuel elements as plates were removed, and the results fit with logistic and step curves and applied in the simulation. These stochastic DP results were compared to DP estimates from a deterministic model assuming a normal curve and typical RSD, yielding insights that could improve effectiveness in the field. These early results illustrate the potential of stochastic models to better understand achieved DP and to improve safeguards effectiveness.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗
DOE OSTI2024

DECOVALEX-2023: Task A Final Report

Task A, also known as HGFrac, examines the fracturing processes that may occur in the Callovo-Oxfordian claystone (COx) in the context of the high-level (HLW) and intermediate-level long-lived (ILW-LL) radioactive waste repository in France. Understanding these processes and improving numerical models to reproduce them will aid in the design, optimization, and safety of the repository. Heat and gas fracturing are studied in two independent subtasks following a stepwise approach: laboratory tests/benchmark exercises, in-situ experiment, and finally, an application case. The in-situ heater experiment aimed to thermally induce a hydraulic fracture; temperature and pore pressure were monitored to detect any evidence of fracturing. The in-situ gas injection experiment aimed to study the effect of the stress orientation and gas injection kinetics on the gas fracturing process. The occurrence of fracturing was monitored by gas pressure measured in the injection interval. In both experiments, the excavation-induced fracture network around the heater/injection boreholes played an important role in the reduction of the compressive stress state, leading to both a tensile and shear failure response of the COx. During the first two years of the project, the research teams working on each task developed and/or proposed numerical approaches for reproducing the occurrence of fracturing in the in-situ experiments. The failure criteria were defined by reproducing the measurements from laboratory extension tests for the heat fracturing subtask. In the gas fracturing subtask, their approaches were used for simulating several benchmark exercises, and an inter-comparison between models was carried out. In both tasks, the developed approaches were compared with a simplified approach considering poro-elasticity for the mechanical behaviour of the COx. Most of the developed approaches are based on a continuous medium that takes into account variations in hydraulic properties due to mechanical degradation, such as plastic deformation or damage. Other approaches implicitly modelled weak planes or embedded discontinuities to reproduce fracture propagation. The potential for fracture initiation was also studied through of a discrete approach. In the second half of the project, the research teams mainly focused on interpretative modelling of two in-situ experiments and a blind prediction exercise to test their respective approaches. The models developed by the research teams were also applied at the repository scale to evaluate fracture initiation in a case study under vi unfavourable conditions, particularly in terms of spacing between High-Level Waste cells. The results showed that the poro-elasticity approach could be an efficient tool for understanding the main processes occurring in the COx. One example is the explicit representation of the excavation-induced fracture network around the boreholes, which yielded acceptable results compared to the measurement data. However, advanced approaches were needed to evaluate the potential increase of the excavation-induced fracture network extend and better understand fracture initiation. The stress analyses carried out by the teams revealed that hydraulic boundary conditions had a strong impact on fracture initiation in the heater experiment. Furthermore, in most cases, the results required higher pore pressure increments to reach fracturing than those measured in the experiment. This implies that the measurements may have been biased by the packer’s capacity to fully isolate the piezometric chambers, leading to lower pressures. On the contrary, there was no agreement on the fracturing mode, as some reported either shear or tensile fracturing, while others reported a combination of the two modes. In the case of gas fracturing, the research teams were limited to the comparison of a single point, which complicated their task. Nonetheless, the numerical results were able to reproduce the measurements and capture processes such as longitudinal gas flow through the excavation-induced fracture network, as suggested by some evidence in the observation piezometric chambers. The numerical models also agreed with the measurements in the sense of higher probability of developing along the injection borehole than radially towards the sound rock. The approaches developed by the research teams showed that they are capable of analysing and reproducing fracture initiation in the COx. However, areas of future work should focus on the fracture propagation and fracture aperture, which were out of the scope of this task. To this end, additional data must be gathered for the parameter characterisation and validation of the numerical models. Nonetheless, various approaches showed promising results as they were able to reproduce fracture development under certain conditions.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Effect of Dilute Acetic Acid Hydrolysis on Xylooligosaccharide Production and the Inhibitory Effect of Cellulolytic Enzyme Lignin from Poplar

Acetic acid (AC) hydrolysis has been reported to prepare xylooligosaccharides (XOS) from poplar. However, the influence of AC hydrolysis on the lignin structure changes is not clear, which is important for the following enzymatic hydrolysis of poplar. Herein, AC was used to produce XOS, and cellulase adsorption on cellulolytic enzyme lignin (CEL) from AC-hydrolyzed poplar and its inhibitory effect on two commercial cellulase preparations were investigated. AC hydrolysis gave a XOS yield of 39.8% from poplar. After AC hydrolysis at 170 °C, the hydrophobicity and ζ-potential of CEL decreased to 2.3 L/g and 14.8 mV, respectively. The adsorption strength of CTec2 on CEL samples did not increase by AC hydrolysis, and the inhibitory effect of CEL on Celluclast 1.5L and β-glucosidase was observed, but not on CTec2. CEL samples improved the lytic polysaccharide monooxygenase (LPMO) activity of the enzymatic hydrolysis by CTec2. After CEL samples were added in enzymatic hydrolysis, the free filter paper activity of Celluclast 1.5L and β-G retained in the enzymatic hydrolysate decreased from 60.5 to 29.3–42.9%. The addition of CEL samples in enzymatic hydrolysis could not decrease the free filter paper activity of CTec2 retained in the enzymatic hydrolysate. In the enzymatic hydrolysis with CEL samples, higher glucose yields were obtained by CTec2 than those by Celluclast 1.5L and β-glucosidase. This work will help to understand the structure and inhibitory effects of AC-CELs and guide the development of AC hydrolysis for the production of XOS and monosaccharides from poplar.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Statistically bias-corrected and downscaled climate models underestimate the adverse effects of extreme heat on U.S. maize yields

Abstract Efforts to understand and quantify how a changing climate can impact agriculture often rely on bias-corrected and downscaled climate information, making it important to quantify potential biases of this approach. Here, we use a multi-model ensemble of statistically bias-corrected and downscaled climate models, as well as the corresponding parent models from the Coupled Model Intercomparison Project Phase 5 (CMIP5), to drive a statistical panel model of U.S. maize yields that incorporates season-wide measures of temperature and precipitation. We analyze uncertainty in annual yield hindcasts, finding that the CMIP5 models considerably overestimate historical yield variability while the bias-corrected and downscaled versions underestimate the largest weather-induced yield declines. We also find large differences in projected yields and other decision-relevant metrics throughout this century, leaving stakeholders with modeling choices that require navigating trade-offs in resolution, historical accuracy, and projection confidence.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRSDate not supplied

Assessment of the Impact of an Advanced Power System on a Turboelectric Single-Aisle Concept Aircraft

Electrified aircraft propulsion concepts show potential in using propulsion airframe inte-gration in order to increase efficiency in flight and therefore decrease fuel burn and emissions.Electrification offers component efficiency values greater than 90 percent, but the loss is in the form of low grade waste heat. A major challenge of electrified aircraft propulsion is managing that heat while minimizing any penalties associated with a thermal management system. This paper explores the effect of two innovations in the management of waste heat at the aircraft system level for a turboelectric single aisle concept. The first innovation is achieving a 3 times reduction in heat by developing high-efficiency components rather than managing the high levels of heat. The second takes advantage of the outer mold line of the aircraft to reject heat directly to the environment passively instead of adding active cooling loops that negatively impact the weight, power, and drag of the aircraft. In order to fully grasp the impact of the advanced power system, we develop methods of modeling the power and thermal management systems to be integrated in the full aircraft conceptual model. We then model the aircraft with a state of the art DC transmission system and active cooling loops as a baseline for our study. Our second model includes the advanced power system with active cooling, which results in a fuel burn reduction of 2.5 percent. Finally, in our third model we assess the benefit of an outer mold line cooling scheme with the advanced power system. The outer mold line cooling scheme with an advanced power system yields an additional 0.8 percent reduction in fuel burn,for an overall fuel burn reduction potential of 3.3 percent in addition to aerodynamic benefits of electrified aircraft propulsion.

Electric Aircraft↗
DOE OSTI2021

Inverse design of equilibrium cluster fluids applied to a physically informed model

Inverse design strategies have proven highly useful for the discovery of interaction potentials that prompt self-assembly of a variety of interesting structures. However, often the optimized particle interactions do not have a direct relationship to experimental systems. In this work, we show that Relative Entropy minimization is able to discover physically meaningful parameter sets for a model interaction built from depletion attraction and electrostatic repulsion that yield self-assembly of size-specific clusters. Here, we then explore the sensitivity of the optimized interaction potentials with respect to deviations in the underlying physical quantities, showing that clustering behavior is largely preserved even as the optimized parameters are perturbed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Anharmonic phonon damping enhances the T c of BCS-type superconductors

In this study, a theory of superconductivity is presented where the effect of anharmonicity, as entailed in the acoustic, or optical, phonon damping, is explicitly considered in the pairing mechanism. The gap equation is solved including diffusive Akhiezer damping for longitudinal acoustic phonons or Klemens damping for optical phonons, with a damping coefficient which, in either case, can be directly related to the Grüneisen parameter and hence to the anharmonic coefficients in the interatomic potential. The results show that the increase of anharmonicity has a strikingly nonmonotonic effect on the critical temperature T c . The optimal damping coefficient yielding maximum T c is set by the velocity of the bosonic mediator. This theory may open up unprecedented opportunities for material design where T c may be tuned via the anharmonicity of the interatomic potential, and presents implications for the superconductivity in the recently discovered hydrides, where anharmonicity is very strong and for which the anharmonic damping is especially relevant.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Biochemical properties of glycerol kinase from the hypersaline-adapted archaeon Haloferax volcanii

ABSTRACT Extremophilic microorganisms are promising candidates for industrial and analytical biocatalysis.Haloferax volcanii, a halophilic archaeon that prefers glycerol over glucose, channels this substrate into central metabolism through glycerol kinase (GK). Here, we report the biochemical properties ofH. volcaniiGK and its potential for biotechnological applications. An N-terminal His-tagged GK was functionalin vivoand yielded 3 mg/L culture—4.5 times more enzyme than a C-terminal StrepII-tagged version. Size exclusion chromatography revealed a glycerol-induced oligomeric shift from homodimer to a dimer-dominant state with detectable tetramer. The purified enzyme showed robust activity across broad pH and salinity ranges, with optimal activity at 100 mM NaCl and 50°C–60°C. It retained catalytic activity in 5%–10% dimethyl sulfoxide (DMSO) and crude glycerol containing methanol. His-GK was freeze-thaw stable and thermotolerant in 2 M NaCl buffers. In the absence of ligands, the enzyme’s melting temperature (T m ) was 80°C. Glycerol increased the T m to 85°C, and combinations with MgCl₂ (84°C) or ATP (88°C) provided further stabilization. The highest T m (89°C) occurred with all three ligands, suggesting a cumulative stabilizing effect. Kinetic analyses revealed positive cooperativity for glycerol, ATP, and Mg² + ; Mn² + and Co² + also supported the activity.H. volcaniiGK is the first known GK to exhibit positive cooperativity with glycerol and ATP. Its high stability and substrate flexibility support its use in biodiesel waste valorization,in vitrobiocatalysis, and biosensor development—applications demanding robust, specific, and stable enzymes. IMPORTANCE This study reveals thatH. volcaniiGK exhibits positive cooperativity for glycerol, ATP, and Mg² + , a kinetic feature not previously reported for glycerol kinases. This behavior enables steep, switch-like responses to small substrate changes, offering unique advantages for biosensor design. Importantly,H. volcaniiGK also maintains high activity under extreme salinity, temperature, broad pH, and solvent conditions that typically limit enzyme use in industrial and environmental applications. These traits make this GK an ideal candidate for enzyme-based biosensors, which often suffer from poor tolerance to pH, solvent, and thermal stress. Its robustness supports its use in cross-linked enzyme crystals, an immobilization method that enhances enzyme stability and reusability under harsh conditions. Moreover, GKs are already employed in Mg² + detection kits; however,H. volcaniiGK’s ability to tolerate and respond to diverse divalent cations (e.g., Co² + , Mn² + ) broadens their potential for pollutant detection and environmental monitoring. These features collectively positionH. volcaniiGK as a valuable biocatalyst for biosensing,in vitrodiagnostics, and biotechnological applications requiring both precision and durability.

Biotechnology & Applied Microbiology↗
NASA NTRS1973

Venus - Radar determination of gravity potential.

We describe a method for the determination of the gravity potential of Venus from multiple-frequency radar measurements. The method is based on the strong frequency dependence of the absorption of radio waves in Venus' atmosphere. Comparison of the differing radar reflection intensities at several frequencies yields the height of the surface relative to a reference pressure contour; combination with measurements of round-trip echo delays allows the pressure, and hence the gravity potential contour, to be mapped relative to the mean planet radius. Since calibration data from other frequencies are unavailable, the absorption-sensitive Haystack Observatory data have been analyzed under the assumption of uniform surface reflectivity to yield a gravity equipotential contour for the equatorial region and a tentative upper bound of .0006 on the fractional difference of Venus' principal equatorial moments of inertia.

Shapiro, I. I.↗
NASA NTRS1983

Phosphine photochemistry in Saturn's atmosphere

The phosphine photochemistry on Saturn is studied with a 1D photochemical model. The PH3 concentration is rapidly depleted with height (scale height 3.5 km) in the upper troposphere. Formation of P, a probable precursor of P4, (a potential red chromophore in the atmosphere), is highly improbable unless the rate constant for the recombination reaction PH + H2 + M yields PH3 + M is less than 10 to the -41st cm exp 6/molecule-squared sec. Coupling of PH3 and hydrocarbon photochemistry, specifically the C2H2 catalyzed photodissociation of CH, is important. Column production rates of the organophosphorus compounds CH3PH2 and HCP of 3 x 10 to the 8th/sq cm sec are predicted, with potentially observable column densities of greater than 1 x 10 to the 17th/sq cm.

Kaye, J. A.↗