Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic strains”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The Challenges of Modeling Defect Behavior and Plasticity across Spatial and Temporal Scales: A Case Study of Metal Bilayer Impact

Atomistic molecular dynamics (MD) and a microstructural dislocation density-based crystalline plasticity (DCP) framework were used together across time scales varying from picoseconds to nanoseconds and length scales spanning from angstroms to micrometers to model a buried copper–nickel interface subjected to high strain rates. The nucleation and evolution of defects, such as dislocations and stacking faults, as well as large inelastic strain accumulations and wave-induced stress reflections were physically represented in both approaches. Both methods showed similar qualitative behavior, such as defects originating along the impactor edges, a dominance of Shockley partial dislocations, and non-continuous dislocation distributions across the buried interface. The favorable comparison between methods justifies assumptions used in both, to model phenomena, such as the nucleation and interactions of single defects and partials with reflected tensile waves, based on MD predictions, which are consistent with the evolution of perfect and partial dislocation densities as predicted by DCP. This substantiates how the nanoscale as modeled by MD is representative of microstructural behavior as modeled by DCP.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effects of Zn and Ca on the deformation texture evolution of Mg–Zn–Ca alloys at elevated temperatures

This work utilized crystal plasticity simulations and experimental thermo-mechanical processing to examine how Zn and Ca content affects texture evolution in Mg–Zn–Ca alloys during simulated hot rolling. Four different compositions were studied: unalloyed Mg and three Mg alloys of ZX0p50 (Mg- 0.5 wt% Zn- 0.1 wt% Ca), ZX30 (Mg-3 wt% Zn- 0.1 wt% Ca), and ZX31 (Mg-3 wt% Zn- 0.3 wt% Ca). Multi-pass Gleeble experiments simulated hot rolling using plane strain conditions. Unalloyed Mg developed a strong basal texture, while the addition of Zn and Ca significantly weakened the texture in ZX30 and ZX31; this reduction was not seen in ZX0p50. Notably, ZX31 exhibited a split basal texture aligned with the rolling direction. Crystal plasticity simulations revealed that the weaker basal texture in ZX30 and ZX31 resulted from reduced activation of basal and twinning modes compared to unalloyed Mg and Zx0p50. Increased Zn and Ca content raised the ratios of basal to pyramidal critical resolved sheer stress (CRSS) and twin to pyramidal CRSS, enhancing pyramidal slip activity and weakening the basal texture. Extension twinning played a critical role in texture development during the first deformation pass. In unalloyed Mg and ZX0p50, twinning led to a strong basal texture, while ZX30 and ZX31 had weak basal textures that increased only slightly with further deformation. The split basal poles simulated in ZX31 were consistent with the experimental findings, highlighting the interplay between alloy composition and texture evolution.

Crystal plasticity finite element↗
DOE OSTI2021

A Review: Microstructural and Phase Evolution in Alloys during Extended Plastic Deformation

Materials in service and during processing are often subjected to plastic deformation. For multi-phase metallic alloys, simple geometric models and atomistic simulations suggest that two distinctive regimes in these materials’ evolution during deformation exist. At low strains, evolutions are often dominated by the kinetic roughening of interfaces, which results from the superdiffusive transport of matter in sheared crystals. Furthermore, at high strains and temperatures where thermal diffusion is sluggish, on the other hand, shearing- induced forced atomic mixing dominates these evolutions, resulting in significantly enhanced solubility. Distinguishing these two regimes is shown to provide a convenient framework for rationalizing and analyzing recent experiments and simulations on wear of layered structures in the low strain-regime and nonequilibrium phase co-existence and self-organization in highly immiscible or reactive alloy systems in the high-strain regime.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Solid-State Joining of Magnesium Sheet to High-Strength Steel

Increasing the use of lightweight materials and implementing enabling manufacturing technologies are the two primary paths toward automotive weight reduction. In many situations, the ability to substitute light weight material requires a need to attach and join light weight material to existing steel substructures requiring dissimilar joining technologies. Dissimilar joining methods currently available in cost range for high volume automotive manufacturing face multiple challenges. The problem is exacerbated in the case of Magnesium alloy to steel joints because of their highly dissimilar nature and lack of mutual miscibility. Additionally, Magnesium’s poor room temperature ductility complicates the use of point fastening technologies. Two emerging solid-state joining technologies Friction Stir assisted Scribe welding (FaST) and Ultrasonic Welding (USW) that employ large amount of plastic deformation at the interface were used to investigate, develop, and understand dissimilar joints between Magnesium Alloy to DP590 Steel. Various process responses including interface temperatures, process forces, strain fields were captured during the development of the welding process. Variety of welded samples were tested and characterized to understand the relationship between welding conditions and joints microstructure and mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Static geometric and material nonlinear analysis.

This paper presents a survey of four aspects of nonlinear analysis - basic formulation, plasticity relations, computational procedures, and methods of solution. This survey is for the most part limited to static geometric and material nonlinear analysis under the assumption of small strains. The two formulations covered are the total Lagrangian and the incremental moving coordinate formulations. A comparison of the two formulations is presented and an attempt is made to clarify the underlying basis of each formulation. The survey of computational procedures reveals that most researchers are now using some form of numerical integration to evaluate nonlinear contributions.

Stricklin, J. A.↗
NASA NTRS1984

Influence of soft inclusions on the strength of wrought materials

The three dimensional soft particles (such as sulfides, silicates and voids) present in most materials are modelled by circular voids in sheet metal. Relationships are sought between the shape and orientation of a hole after rolling and testing in tension. Then, the effect of hole shape and size on mechanical properties is considered experimentally. The presence of voids has a negligible influence on the ultimate tensile stress of ductile materials based on the unperforated area because plastic flow neutralizes the stress intensification present in the elastic region. However, the shape and orientation of the defects are found to play an important role relative to strain at fracture. In certain engineering applications the strain at fracture is more important than the stress at fracture and in this sense the presence of voids are considered to influence the strength of a ductile material.

Pai, D. M.↗
NASA NTRS1984

Tensile Fracture of Ductile Materials

For brittle materials, circular voids play an important role relative to fracture, intensifing both tensile and compressive stresses. A maximum intensified tensile stress failure criterion applies quite well to brittle materials. An attempt was made to explore the possibility of extending the approach to the tensile fracture of ductile materials. The three dimensional voids that exist in reality are modelled by circular holes in sheet metal. Mathematical relationships are sought between the shape and size of the hole, after the material is plastically deformed, and the amount of deformation induced. Then, the effect of hole shape, size and orientation on the mechanical properties is considered experimentally. The presence of the voids does not affect the ultimate tensile strength of the ductile materials because plastic flow wipes out the stress intensification caused by them. However, the shape and orientation of the defect is found to play an important role in affecting the strain at fracture.

Pai, D. M.↗
NASA NTRS1995

JOVE Pilot Research Study in Astronomy and Microgravity Sciences

The purpose of this project was to develop hardware and software facilities for evaluating the biomechanical interactions between human hands and space suit gloves. We have constructed a prototype of the glove to demonstrate its sensing technologies. There are two types of sensors in the glove. The positions of the fingers are measured using bend sensors based on the CyberGlove design. This sensor consists of two strain gages mounted to a 0.003 inch thick mylar sheet. The sensor is encapsulated using 0.001 inch kapton film to give it sufficient rigidity. A long gage is used to average the strain generated in the sensor due to bending. This average strain produces an output signal proportional to the angle of the bend. The force sensor, FSR, is manufactured by Interlink. It consists of conductive ink sandwiched between two plastic sheets. An electrode is printed on one of the plastic sheets using silver ink. When the electrode makes contact, current flows through the conductive ink. The resistance of the ink pad is sensitive to pressure. We have also developed circuits for exciting and measuring the sensors. The current version requires a single sided twelve volt power supply which is one inch long and 0.4 inches in diameter.

Strauss, Alvin M.↗
NASA NTRS1947

The Elasto-Plastic Stability of Plates

This article explains results developed from the following research: 'The Stability of Plates and Shells beyond the Elastic Limit.' A significant improvement is found in the derivation of the relations between the stress factors and the strains resulting from the instability of plates and shells. In a strict analysis, the problem reduces to the solution of two simultaneous nonlinear partial differential equations of the fourth order in the deflection and stress function, and in the approximate analysis to a single linear equation of the Bryan type. Solutions are given for the special cases of a rectangular plate buckling into a cylindrical form, and of an arbitrarily shaped plate under uniform compression. These solutions indicate that the accuracy obtained by the approximate method is satisfactory.

Ilyushin, A. A.↗
DOE OSTI2024

Interim Development of new Class B Code Case with Variable Design Lifetime and enhanced design rules to guard against cyclic structural failure mode

This report summarizes updates on the ongoing development of the new American Society of Mechanical Engineers Section III, Division 5, Class B rules to address the potential failure modes of Class B components. An initial design-by-analysis approach and supporting design rules are presented. The elastic-perfectly plastic (EPP) analysis approach has been adopted for primary stress limit and ratcheting check to prevent the component failure against the structural failure mode against primary load and strain accumulation due to cyclic loads. The creep-fatigue damage assessment uses explicitly defined elastic follow-up calculated from the stress concentration region of given component. Damage fraction calculation uses a novel coupled approach to capture the influence of the elastic follow-up and provide adequate conservatism for Class B components. The proposed Class B rules does not use the stress classification approach and uses the combined loads to assess component.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Shear-based deformation processing of age-hardened aluminum alloy for single-step sheet production

Shear-based deformation processing by hybrid cutting-extrusion and free machining are used to make continuous strip, of thickness up to one millimeter, from low-workability AA6013-T6 in a single deformation step. The intense shear can impose effective strains as large as 2 in the strip without pre-heating of the workpiece. The creation of strip in a single step is facilitated by three factors inherent to the cutting deformation zone: highly confined shear deformation, in situ plastic deformation-induced heating and high hydrostatic pressure. The hybrid cutting-extrusion, which employs a second die located across from the primary cutting tool to constrain the chip geometry, is found to produce strip with smooth surfaces (S a < 0.4 μm) that is similar to cold-rolled strip. The strips show an elongated grain microstructure that is inclined to the strip surfaces – a shear texture – that is quite different from rolled sheet. Furthermore, this shear texture (inclination) angle is determined by the deformation path. Through control of the deformation parameters such as strain and temperature, a range of microstructures and strengths could be achieved in the strip. When the cutting-based deformation was done at room temperature, without workpiece pre-heating, the starting T6 material was further strengthened by as much as 30% in a single step. In elevated-temperature cutting-extrusion, dynamic recrystallization was observed, resulting in a refined grain size in the strip. Implications for deformation processing of age-hardenable Al alloys into sheet form, and microstructure control therein, are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Androgynous { 10 1 ¯ 2 } twin in zinc

Under ambient conditions, Zn is a hexagonal metal with a large c / a ratio of 1.856. Plastic deformation is predominantly accommodated by basal 〈 a 〉 slip and compression twins on the { 10 1 ¯ 2 } planes. Increasing hydrostatic pressure drastically reduces the c / a ratio of Zn and, when a critical threshold of c / a = 3 at about 10 GPa is crossed, the { 10 1 ¯ 2 } twins are predicted to change from compressive to tensile in nature. What happens at the transition point, when c / a = 3 , remains unknown. Here, we strain-cycle a textured polycrystalline sample of pure Zn at uniform hydrostatic pressures ranging between 2 and 17 GPa, over which the c / a ratio crosses the c / a = 3 compressive-tensile transition for { 10 1 ¯ 2 } twins. During deformation, the state of the sample is monitored through x-ray diffraction to extract texture and internal strain evolution. By comparing the experimental results with the predictions of an elastoviscoplastic polycrystal simulation, we confirm the androgynous nature of { 10 1 ¯ 2 } twin response at low and high pressures. When c / a = 3 , polycrystalline Zn does not display any evidence of twinning and its plastic behavior is controlled by mostly basal and pyramidal 〈 c + a 〉 slip activity, with a very small contribution of prismatic 〈 a 〉 slip. Evidence for the activity of other { 10 1 ¯ n } twinning modes, which have been suggested for Zn under high pressure, are not observed. Published by the American Physical Society 2024

Merkel, Sébastien (ORCID:000000032767581X)↗
NASA NTRS2014

Slow Strain Rate Tensile Testing to Assess the Ability of Superalloys to Resist Environment-Assisted Intergranular Cracking

Intergranular fatigue crack initiation and growth due to environmental degradation, especially at notched features, can often limit the fatigue life of disk superalloys at high temperatures. For clear comparisons, the effects of alloy composition on cracking in air needs to be understood and compared separately from variables associated with notches and cracks such as effective stress concentration, plastic flow, stress relaxation, and stress redistribution. The objective of this study was to attempt using simple tensile tests of specimens with uniform gage sections to compare the effects of varied alloy composition on environment-assisted cracking of several powder metal and cast and wrought superalloys including ME3, LSHR, Udimet 720, ATI 718Plus alloy, Haynes 282, and Inconel 740. Slow and fast strain-rate tensile tests were found to be a useful tool to compare propensities for intergranular surface crack initiation and growth. The effects of composition and heat treatment on tensile fracture strain and associated failure modes were compared. Environment interactions were determined to often limit ductility, by promoting intergranular surface cracking. The response of various superalloys and heat treatments to slow strain rate tensile testing varied substantially, showing that composition and microstructure can significantly influence environmental resistance to cracking.

Heat resistant alloys↗
NASA NTRS1998

WARP3D-Release 10.8: Dynamic Nonlinear Analysis of Solids using a Preconditioned Conjugate Gradient Software Architecture

This report describes theoretical background material and commands necessary to use the WARP3D finite element code. WARP3D is under continuing development as a research code for the solution of very large-scale, 3-D solid models subjected to static and dynamic loads. Specific features in the code oriented toward the investigation of ductile fracture in metals include a robust finite strain formulation, a general J-integral computation facility (with inertia, face loading), an element extinction facility to model crack growth, nonlinear material models including viscoplastic effects, and the Gurson-Tver-gaard dilatant plasticity model for void growth. The nonlinear, dynamic equilibrium equations are solved using an incremental-iterative, implicit formulation with full Newton iterations to eliminate residual nodal forces. The history integration of the nonlinear equations of motion is accomplished with Newmarks Beta method. A central feature of WARP3D involves the use of a linear-preconditioned conjugate gradient (LPCG) solver implemented in an element-by-element format to replace a conventional direct linear equation solver. This software architecture dramatically reduces both the memory requirements and CPU time for very large, nonlinear solid models since formation of the assembled (dynamic) stiffness matrix is avoided. Analyses thus exhibit the numerical stability for large time (load) steps provided by the implicit formulation coupled with the low memory requirements characteristic of an explicit code. In addition to the much lower memory requirements of the LPCG solver, the CPU time required for solution of the linear equations during each Newton iteration is generally one-half or less of the CPU time required for a traditional direct solver. All other computational aspects of the code (element stiffnesses, element strains, stress updating, element internal forces) are implemented in the element-by- element, blocked architecture. This greatly improves vectorization of the code on uni-processor hardware and enables straightforward parallel-vector processing of element blocks on multi-processor hardware.

Koppenhoefer, Kyle C.↗
DOE OSTI2023

Atomic faulting induced exceptional cryogenic strain hardening in gradient cell–structured alloy

Coarse-grained materials are widely accepted to display the highest strain hardening and the best tensile ductility. We experimentally report an attractive strain hardening rate throughout the deformation stage at 77 kelvin in a stable single-phase alloy with gradient dislocation cells that even surpasses its coarse-grained counterparts. Contrary to conventional understanding, the exceptional strain hardening arises from a distinctive dynamic structural refinement mechanism facilitated by the emission and motion of massive multiorientational tiny stacking faults (planar defects), which are fundamentally distinct from the traditional linear dislocation–mediated deformation. In conclusion, the dominance of atomic-scale planar deformation faulting in plastic deformation introduces a different approach for strengthening and hardening metallic materials, offering promising properties and potential applications.

Gradient dislocation structure↗
DOE OSTI2021

Characterization of Embedded Sensors in Stainless Steel Test Articles and Design/Planning for MAGNET Testing

The nuclear industry is pursuing microreactors that can be factory assembled and deployed to remote regions for reliable power generation. One class of microreactors uses a monolithic metal core block coupled to heat pipes for heat rejection, which results in significant thermal stresses in the monolithic structures. This work describes the initial characterization and test plan for evaluating stainless steel test articles fabricated with embedded sensors for measuring heat pipe performance limits, as well as spatially distributed temperatures and strains during electrically heated thermal testing. The electrically heated testing will be performed in the non-nuclear Microreactor Agile Non-Nuclear Testbed and Single Primary Heat Extraction and Removal Emulator facilities located at Idaho National Laboratory. The goals of these tests are to (1) accurately monitor temperature and strain distributions that result from differential thermal expansion in the test articles and (2) quantify heat rejection limits of heat pipes as a function of operating temperature and working fluid during steady-state and transient operations. More generally, the ability to monitor component and system health during microreactor operation is attractive for providing a high sensor density to inform a limited number of microreactor operators to ultimately reduce operation and maintenance costs and move toward semi-autonomous operation. This report discusses the characterization of embedded thermocouples and fiber optic sensors in relevant test articles, including cylindrical pipes and hexagonal monolithic test articles for heat pipe-based reactors. The sensors were embedded by placing them in machined channels and then building up additional material by using ultrasonic additive manufacturing (UAM). UAM is a solid-state welding process that uses downward pressure and a lateral scrubbing motion to bond thin metal foils to a base material layer by layer. The ultrasonic welding process relies on the plastic deformation of the metal—as opposed to typical melting and solidification—to break oxide scales and bond the metal layers. The characterization of these embedded sensors included evaluating fiber optic signal attenuation, observing residual strain in the fibers, investigating microstructural and mechanical aspects, and demonstrating the sensors under various thermal loads and acoustic vibrations. Post-embedding characterization showed a fine grain structure (<1 μm) near the interfaces of the bonded foils as a result of severe deformation from the welding process. A large increase in hardness was observed at the foil interfaces and the fiber/matrix interface compared with the bulk matrix. Even when compared with the SS304 interfaces, the higher hardness observed around the embedded fiber suggests a higher degree of deformation due to the soft metal coating around the silica fiber core. The distributed fiber-optic temperature sensors and embedded thermocouples reliably measured temperature distributions during steady-state and transient thermal testing. The embedded fiber-optic sensors reliably measured strain during both transient and steady-state testing and properly identified resonant frequencies during acoustic testing.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Multi-stage load partitioning in additively manufactured Al6061+TiC nanocomposite characterized by in-situ neutron diffraction

Metal matrix composites (MMCs), combining metal matrix and ceramic particles, exhibit high mechanical strength and stiffness compared to conventional metallic materials. During fusion-based additive manufacturing (AM), MMCs undergo a rapid heating and cooling thermal history, which affects the interfacial bonding, thermal misfit stress and mechanical load transfer behavior between the metal matrix and particles, thus impacting the bulk mechanical performance. Here, we investigate the deformation dynamics and phase-specific load transfer in fusion-based AMed Al6061 +TiC MMCs through in-situ neutron diffraction. By calculating the phase-specific lattice strains, a multi-stage load transfer and deformation behavior during uniaxial compression is revealed: (1) elastic deformation in Stage I for both phases; (2) sudden stress rebalance between two phases in Stage II, evidenced by a sudden decrease in Al lattice strain and increase in TiC; (3) active load carrying by both phases in Stage III, with both phases experiencing an increase in lattice strains. Further, the deformation mechanism of each stage is deducted by correlating the evolutions of the interphase stresses and peaks’ broadening and intensity of the Al matrix. The local plastic deformation of the Al matrix near the phase interface is triggered and leads to stress rebalancing in Stage II. The global plastic deformation subsequently propagates throughout the Al matrix in Stage III, and the composite is further hardened through both dislocation multiplication and load transfer. The findings offer valuable insights into deformation and load-sharing behavior in AMed MMCs.

36 MATERIALS SCIENCE↗