Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “mixture experiment models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Flashback Studies of High-Hydrogen Flames using High-Speed OH Planar Laser-Induced Fluorescence

Flame flashback is a crucial challenge during the application of high-hydrogen fuels for the development of next-generation lean premixed combustors. The fundamentals of stable flame configuration, flashback phenomena, and spatiotemporal information of flame dynamics in a premixed, swirl-stabilized burner are investigated experimentally at atmospheric pressure conditions using high-repetition-rate nanosecond (ns)-duration hydroxyl radical planar laser-induced fluorescence (OH-PLIF) measurements. The inlet conditions are varied systematically with respect to equivalence ratio (ϕ), hydrogen percentage in a hydrogen-methane mixture (50%–90%) and pre-mixer velocities and the experiments are performed on the burner modified to provide optical access to the premixing section. Signal interferences such as saturation effects, background chemiluminescence, and laser non-uniformity issues were minimized or corrected during data acquisition and subsequent data processing steps. A stable flame characterization was performed at 20 kHz-repetition-rate for varied pre-mixer velocities, hydrogen content and ϕ in the reactant mixture and lift-off length (L) investigation showed dependence on each of these parameters. Flame dynamics such as flame flashback events, local ignition, local extinction, flame curvature as well as the main reaction zone of the combustion mechanism are well characterized. Flashback ϕ showed an expected linearly increasing trend with increasing pre-mixer velocity and decreasing hydrogen content and the conclusions drawn aligned well with detailed L investigation. Such spatially and temporally resolved kHz-rate OH-PLIF is a promising technique to observe rapidly occurring flashback dynamics and can further validate turbulence-chemistry interaction models of swirling flames.

Parajuli, Pradeep↗

Marangoni Effects on Near-Bubble Microscale Transport During Boiling of Binary Fluid Mixtures

In earlier investigations, Marangoni effects were observed to be the dominant mechanism of boiling transport in 2-propanol/water mixtures under reduced gravity conditions. In this investigation we have examined the mechanisms of binary mixture boiling by exploring the transport near a single bubble generated in a binary mixture between a heated surface and cold surface. The temperature field created in the liquid around the bubble produces vaporization over the portion of its interface near the heated surface and condensation over portions of its interface near the cold surface. Experiments were conducted using different mixtures of water and 2-propanol under 1g conditions and under reduced gravity conditions aboard the KC135 aircraft. Since 2-propanol is more volatile than water, there is a lower concentration of 2-propanol near the hot surface and a higher concentration of 2-propanol near the cold plate relative to the bulk quantity. This difference in interface concentration gives rise to strong Marangoni effects that move liquid toward the hot plate in the near bubble region for 2-propanol and water mixtures. In the experiments in this study, the pressure of the test system was maintained at about 5 kPa to achieve the full spectrum of boiling behavior (nucleate boiling, critical heat flux and film boiling) at low temperature and heat flux levels. Heat transfer data and visual documentation of the bubble shape were extracted from the experimental results. In the 1-g experiments at moderate to high heat flux levels, the bubble was observed to grow into a mushroom shape with a larger top portion near the cold plate due to the buoyancy effect. The shape of the bubble was somewhat affected by the cold plate subcooling and the superheat of the heated surface. At low superheat levels for the heated surface, several active nucleation sites were observed, and the vapor stems from them merged to form a larger bubble. The generation rate of vapor is moderate in this regime and the bubble shape is cylindrical in appearance. In some instances, the bubble interface appeared to oscillate. At higher applied heat flux levels, the top of the bubble became larger, apparently to provide more condensing interface area adjacent to the cold plate. Increasing the applied heat flux ultimately led to dry-out of the heated surface, with conditions just prior to dryout corresponding to the maximum heat flux (CHF). A more stable bubble was observed when the system attained the minimum heat flux (for film boiling). In this regime, most of the surface under the bottom of the bubble was dry with nucleate boiling sometimes occuring around the contact perimeter of the bubble at heated surface. Different variations (e.g. gap between two plates, molar concentration of the liquid mixture) of the experiments were examined to determine parametric effects on the boiling process and to determine the best conditions for the KC135 reduced gravity tests. Variation of the gap was found to have a minor impact on the CHF. However, reducing the gap between the hot and cold surface was observed to significantly reduce the minimum heat flux for fixed molar concentration of 2-propanol. In the reduced gravity experiments aboard the KC135 aircraft, the bubble formed in the 6.4 mm gap was generally cylindrical or barrel shaped and it increased its extent laterally as the surface superheat increased. In reduced gravity experiments, dryout of the heated surface under the bubble was observed to occur at a lower superheated temperature than for 1g conditions. Observed features of the boiling process and heat transfer data under reduced gravity will be discussed in detail. The results of the reduced gravity experiments will also be compared to those obtained in comparable 1g experiments. In tandem with the experiments we are also developing a computational model of the transport in the liquid surrounding the bubble during the boiling process. The computational model uses a level set method to model motion of the interface. It will incorporate a macroscale treatment of the transport in the liquid gap between the surfaces and a microscale treatment of transport in the regions between the bubble interface and the solid surfaces. The features of the model will be described in detail. Future research directions suggested by the results to date will also be discussed.

V. Carey↗

Kinetics of the reaction of hydrated lime with SO{sub 2} at low temperatures: effects of the presence of CO{sub 2}, O{sub 2}, and NOx

The effects of the presence Of CO{sub 2}, O{sub 2}, and NOx in the flue gas on the kinetics of the sulfation of hydrated lime at low temperatures were studied using a differential fixed-bed reactor. When O{sub 2} and NOx were not present together the reaction kinetics was about the same as that under gas mixtures containing SO{sub 2}, H{sub 2}O, and N2 only. When both O{sub 2} and NOx were present, sulfation of hydrated lime was greatly enhanced, forming a large amount of calcium sulfate in addition to calcium sulfite. Sulfation of hydrated lime was well described by the surface coverage model, despite the gas-phase conditions being different. Relative humidity is the major factor affecting the reaction, and its effect was more marked when both O{sub 2} and NOx were present. The kinetic model equations obtained in this work can be used to describe the sulfation of hydrated lime in the low-temperature dry and semidry flue gas desulfurization processes with or without an upstream NOx removal unit.

01 COAL, LIGNITE, AND PEAT↗

Understanding the ignition mechanism of high-pressure spray flames

A conceptual model for turbulent ignition in high-pressure spray flames is presented. The model is motivated by first-principles simulations and optical diagnostics applied to the Sandia n-dodecane experiment. The Lagrangian flamelet equations are combined with full LLNL kinetics (2755 species; 11,173 reactions) to resolve all time and length scales and chemical pathways of the ignition process at engine-relevant pressures and turbulence intensities unattainable using classic DNS. The first-principles value of the flamelet equations is established by a novel chemical explosive mode-diffusion time scale analysis of the fully-coupled chemical and turbulent time scales. Contrary to conventional wisdom, this analysis reveals that the high Damköhler number limit, a key requirement for the validity of the flamelet derivation from the reactive Navier–Stokes equations, applies during the entire ignition process. Corroborating Rayleigh-scattering and formaldehyde PLIF with simultaneous schlieren imaging of mixing and combustion are presented. Our combined analysis establishes a characteristic temporal evolution of the ignition process. First, a localized first-stage ignition event consistently occurs in highest temperature mixture regions. This initiates, owed to the intense scalar dissipation, a turbulent cool flame wave propagating from this ignition spot through the entire flow field. This wave significantly decreases the ignition delay of lower temperature mixture regions in comparison to their homogeneous reference. This explains the experimentally observed formaldehyde formation across the entire spray head prior to high-temperature ignition which consistently occurs first in a broad range of rich mixture regions. There, the combination of first-stage ignition delay, shortened by the cool flame wave, and the subsequent delay until second-stage ignition becomes minimal. A turbulent flame subsequently propagates rapidly through the entire mixture over time scales consistent with experimental observations. As a result, we demonstrate that the neglect of turbulence-chemistry-interactions fundamentally fails to capture the key features of this ignition process.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Using Computationally-Determined Properties for Machine Learning Prediction of Self-Diffusion Coefficients in Pure Liquids

The ability to predict transport properties of liquids quickly and accurately will greatly improve our understanding of fluid properties both in bulk and complex mixtures, as well as in confined environments. Such information could then be used in the design of materials and processes for applications ranging from energy production and storage to manufacturing processes. As a first step, we consider the use of machine learning (ML) methods to predict the diffusion properties of pure liquids. Recent results have shown that Artificial Neural Networks (ANNs) can effectively predict the diffusion of pure compounds based on the use of experimental properties as the model inputs. In the current study, a similar ANN approach is applied to modeling diffusion of pure liquids using fluid properties obtained exclusively from molecular simulations. A diverse set of 102 pure liquids is considered, ranging from small polar molecules (e.g., water) to large nonpolar molecules (e.g., octane). Self-diffusion coefficients were obtained from classical molecular dynamics (MD) simulations. Since nearly all the molecules are organic compounds, a general set of force field parameters for organic molecules was used. The MD methods are validated by comparing physical and thermodynamic properties with experiment. Computational input features for the ANN include physical properties obtained from the MD simulations as well as molecular properties from quantum calculations of individual molecules. Furthermore, fluid properties describing the local liquid structure were obtained from center of mass radial distribution functions (COM-RDFs). Feature sensitivity analysis revealed that isothermal compressibility, heat of vaporization, and the thermal expansion coefficient were the most impactful properties used as input for the ANN model to predict the MD simulated self-diffusion coefficients. The MD-based ANN successfully predicts the MD self-diffusion coefficients with only a subset (2 to 3) of the available computationally determined input features required. A separate ANN model was developed using literature experimental self-diffusion coefficients as model targets. Although this second ML model was not as successful due to a limited number of data points, a good correlation is still observed between experimental and ML predicted self-diffusion coefficients.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Simulation of macromolecule self-assembly in solution: A multiscale approach

One of the most common processes to produce polymer nanoparticles is to induce self-assembly by using the solvent-displacement method, in which the polymer is dissolved in a “good” solvent and the solution is then mixed with an “anti-solvent”. The polymer ability to self-assemble in solution is therefore determined by its structural and transport properties in solutions of the pure solvents and at the intermediate compositions. In this work, we focus on poly-ε-caprolactone (PCL) which is a biocompatible polymer that finds widespread application in the pharmaceutical and biomedical fields, performing simulation at three different scales using three different computational tools: full atomistic molecular dynamics (MD), population balance modeling (PBM) and computational fluid dynamics (CFD). Simulations consider PCL chains of different molecular weight in solution of pure acetone (good solvent), of pure water (anti-solvent) and their mixtures, and mixing at different rates and initial concentrations in a confined impinging jets mixer (CIJM). Our MD simulations reveal that the nano-structuring of one of the solvents in the mixture leads to an unexpected identical polymer structure irrespectively of the concentration of the two solvents. In particular, although in pure solvents the behavior of the polymer is, as expected, very different, at intermediate compositions, the PCL chain shows properties very similar to those found in pure acetone as a result of the clustering of the acetone molecules in the vicinity of the polymer chain. We derive an analytical expression to predict the polymer structural properties in solution at different solvent compositions and use it to formulate an aggregation kernel to describe the self-assembly in the CIJM via PBM and CFD. Simulations are eventually validated against experiments.

36 MATERIALS SCIENCE↗

Spherical flame characteristics of heptane/iso-butanol mixture droplets

Experimental data and detailed numerical modelling are presented on the burning characteristics of a model gasoline/biofuel mixture consisting of n-heptane and iso-butanol. A droplet burning in an environment that minimises the influence of buoyant and forced convective flows in the standard atmosphere is used to promote one-dimensional gas transport to facilitate numerical modelling of the droplet burning process. The numerical model includes a detailed combustion kinetic mechanism, unsteady gas and liquid transport, multicomponent diffusion inside the droplet, variable properties, and non-luminous radiative heat transfer from the flame. The numerical simulation was validated by experimental measurements in the standard atmosphere which showed good agreement with the evolutions of droplet and flame diameters. The iso-butanol concentration had a strong effect on formation of particulates. Above ~20% (volume) iso-butanol, flame luminosity was significantly diminished anddecreased with increasing iso-butanol concentration, while CO2 emissions as a representative greenhouse gas were not strongly influenced by the iso-butanol loading. The soot shell was located near a 1350 K isotherm for concentrations up to 20% (volume) iso-butanol, suggesting this value as a possible soot inception temperature for the mixture droplet. The combustion rate decreased with increasing iso-butanol concentration which was attributed to iso-butanol's higher liquid density. No evidence of a low temperature burning regime, or of extinction, was found (in experiments and simulations) for the small droplet sizes investigated.

Dalili, Alireza↗

Experimental Verification of Solidification Stress Theory

A research program is being conducted to develop a crack-free ceramic waste form (CWF) to be used for long term encasement of fission products and actinides resulting from processing spent nuclear fuel. Cracking usually occurs in the cooldown phase of the glass or ceramic formations. A crack-free formation should have more resistance to leaching than one with many cracks. In the research leading up to producing a CWF, a model was developed that proposes a permanent stress develops when the melt solidifies and that this stress can cause failure as the CWF nears room temperature. This paper reports on how the formation, CWF2, confirms the existence of this stress. The solidification stress is in addition to and of opposite sign of the thermal stress. Its derivation is reported on in Ref. 1. Cracking of the CWF would occur at low temperatures if solidification stress exists but at high temperatures if it doesn’t. If solidification stress occurs, then the cooldown rate during solidification should be reduced. If not, it should be reduced when the thermal stresses are highest. Recording cracking sounds confirm the existence of this solidification stress since cracking occurred during the low temperature phase of the cooldown. As a side purpose of this paper, a cooldown rate is proposed that should eliminate cracking in the next experiment, CWF3. CWF2 is a prototype vertical ceramic waste cylinder formed over a period of 10 days by heating a mixture of 75% zeolite, 25% glass frit in an argon atmosphere furnace through melting to 925 C and then cooling through solidification to room temperature. It is approximately 1 m high, 0.5 m in diameter, weighs about 400 kg, and is formed in a stainless steel can 0.5 cm thick. This cylinder developed many cracks on cooldown. At least 15 loud cracks were recorded over a period of 4 days at the end of cooldown when the temperatures were below 400 C. The CWF2 surface and centerline temperatures at mid height were measured which allowed the stress to be calculated. The timing of the cracks was compared to the time the calculated total stress exceeded the tensile stress limit and verified that the cause of the cracking was solidification stress and not thermal stress. Since the CWF is encased in a can in a furnace, the cracks cannot be easily observed but can be detected with sound measurements. Similarly, the stress cannot be measured but only estimated with analysis. Destructive examination of the CWF after cooldown was used to determine the pattern of the cracking which appeared to be initiated mainly in the inner region which is evidence the cracking is due to solidification stress.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Comustion of HAN-Based Monopropellant Droplets in Reduced Gravity

Hydroxylammonium nitrate (HAN) is a major constituent in a class of liquid monopropellants that have many attractive characteristics and which display phenomena that differ significantly from other liquid monopropellants. They are composed primarily of HAN, H2O and a fuel species, often triethanolammonium nitrate (TEAN). HAN-based propellants have attracted attention as liquid gun propellants, and are attractive for NASA spacecraft propulsion applications. A representative propellant is XM46. This mixture is 60.8% HAN, 19.2% TEAN and 20% H2O by weight. Other HAN-based propellant mixtures are also of interest. For example, methanol and glycine have been investigated as potential fuel species for HAN-based monopropellants for thruster applications. In the present research, experimental and theoretical studies are performed on combustion of HAN-based monopropellant droplets. The fuel species considered are TEAN, methanol and glycine. Droplets initially in the mm size range are studied at pressures up to 30 atm. These pressures are applicable to spacecraft thruster applications. The droplets are placed in environments with various amounts of Ar, N2, O2, NO2 and N2O. Reduced gravity is employed to enable observations of burning rates and flame structures to be made without the complicating effects of buoyant and forced convection. Normal gravity experiments are also performed in this research program. The experiment goals are to provide accurate fundamental data on deflagration rates, gasphase temperature profiles, transient gas-phase flame behaviors, the onset of bubbling in droplets at lower pressures, and the low-pressure deflagration limit. Theoretical studies are performed to provide rational models of deflagration mechanisms of HAN-based liquid propellants. Besides advancing fundamental knowledge, this research should aid in applications (e.g., spacecraft thrusters and liquid propellant guns) of this unique class of monopropellants.

Shaw, B. D.↗

Lunar soil evolution processes and Apollo 16 core 60013/60014

Soils of the 62-cm deep Apollo 16 double drive tube 60013/14 are mature at the top and submature at the bottom. Modal analyses of 5529 grains from the 90-150 micrometers and the 500-1000 micrometers fractions from 12 levels of the core show that, in general, agglutinate abundance increases somewhat monotonically to the top and mimics the Is/FeO profile. There is a general decrease in the modal abundance of monomineralic fragments towards the top, suggesting that agglutinates were formed in part at the expense of monomineralic grains, especially feldspars, which are by far the most abundant mineral in these soils. In detail, the top 27 cm of the core differs from the bottom 21 cm, and the middle 14 cm is intermediate in its properties. In the upper segment, variations in the abundances of feldspars correspond with those of feldspathic fragmental breccias and cataclastic anorthosites; in the bottom segment, a similar but weak correspondence between feldspars and crystalline matrix breccias is observed. Mixing of the comminuted products of these three rock types likely produced the bulk of the core material. Many single feldspars in all size fractions are remarkably fresh, show no damage from shock, and are similar in appearance to the large feldspars in anorthosites and feldspathic fragmental breccias, which we consider to be the primary sources of single feldspars in this core. Major (Na, Al, Si, K, Ca) and minor (Fe, Ba) element analyses of 198 single feldspar grains indicate the presence of only one population of feldspars, which is consistent with our interpretation of feldspar provenance. Classification of 890 monomineralic feldspar, olivine, pyroxene, and glass spherules on the basis of the presence or absence of thin brownish coating--related to reworking at the surface--shows that coated grains are much more abundant in the top segment than in the bottom segment. A comparison with the mixing and maturation model (McKay et al., 1977) of soils in the core 60009/10, some 60 m away from 60013/14, shows that mixtures of an immature, nearly pure plagioclase soil (dominant in 60009/10) and another immature, crystalline breccia-rich soil (dominant in 60013/14) may have matured through in situ reworking to produce the soils under investigation. We conclude that the soils in this core are products of mixing along soil evolution Path 2 of McKay et al. (1974). Superimposed on that soil column is the reworking of the upper part, which has evolved more recently along Path 1. This core thus represents a consanguineous column of the lunar regolith with an upper reworked segment.

short duration↗

Lattice dynamics, sound velocities, and atomic environments of szomolnokite at high pressure

Complex mixtures of sulfates, silicates, and ice have been observed in a variety of planetary environments on Earth, Mars and the icy satellites of the solar system. Characterizing the properties of the corresponding compositional endmembers is important for understanding the interiors of a range of planetary bodies in which these phases are observed. To measure the electronic and vibrational properties of the pure ferrous iron endmember of the kieserite group, szomolnokite, (FeSO 4 ∙H 2 O), we have performed synchrotron 57 Fe nuclear resonant inelastic and forward scattering experiments in the diamond-anvil cell up to 14.5 GPa. This pressure range covers depths within Earth’s interior relevant to sulfur cycling in subduction zones and the range of pressures expected within icy satellite interiors. We find evidence of crystal lattice softening, changes in elastic properties, and changes in the electric field gradients of iron atoms associated with two structural transitions occurring within the experimental pressure range. Here we apply these findings to icy satellite interiors, including discussion of elastic properties, modeling of ice-sulfate aggregates, and implications for tidal observations.

58 GEOSCIENCES↗

Nuclear Safety [Vol. 36, No. 1, January-June 1995]

Nuclear Safety is a journal that covers significant issues in the field of nuclear safety. Its primary scope is safety in the design, construction, operation, and decommissioning of nuclear power reactors worldwide and the research and analysis activities that promote this goal, but it also encompasses the safety aspects of the entire nuclear fuel cycle, including fuel fabrication, spent-fuel processing and handling, and nuclear waste disposal, the handling of fissionable materials and radioisotopes, and the environmental effects of all these activities. Table of Contents for this issue follows. THE CHORNOBYL ACCIDENT: 1 The Chornobyl Accident Revisited, Part II: The State of the Nuclear Fuel Located Within the Chornobyl Sarcophagus, A A. Borovoi and A. R. Sich; GENERAL SAFETY CONSIDERATIONS: 33 Nuclear Power Safety in Central and Eastern Europe, R. Wilson; 46 Safety of Nuclear Power Reactors in the Former Eastern European Countries, S. Chakraborty; 53 Technical Note: On the Definition of Common-Cause Failures, H. Paula; ACCIDENT ANALYSIS: 58 Modeling and Analysis of Core-Debris Recriticality During Hypothetical Severe Accidents in the Advanced Neutron Source Reactor, S.-H. Kim, V. Georgevich, D. B. Simpson, C. O. Slater, and R. P. Taleyarkhan; 68 Ignitability of Hydrogen/Oxygen/Diluent Mixtures in the Presence of Hot Surfaces, R. K. Kumar and G. W. Koroll; 94 Coupled RELAP5 and CONTAIN Accident Analysis Using PVM, K. A. Smith, A. J. Baratta, and G. E. Robinson; CONTROL AND INSTRUMENTATION: 109 Application of Fuzzy Logic in Nuclear Reactor Control Part I: An Assessment of State-of-the-Art, A. S. Heger, N. K. Alang-Rashid, and M. Jamshidi; DESIGN FEATURES: 122 Twenty-Third DOE/NRC Nuclear Air-Cleaning and Treatment Conference, R. R. Bellamy, J. J. Hayes, and M. W. First; ENVIRONMENTAL EFFECTS: 135 Atmospheric Dispersion and the Radiological Consequences of Normal Airborne Effluents from a Nuclear Power Plant, D. Fang, C. Z. Sun, and L. Yang; 142 Calculation of Distribution Coefficients for Radionuclides in Soils and Sediments, I. Puigdomenech and U. Bergstrom: OPERATING EXPERIENCES: 155 Reactor Shutdown Experience, Compiled by J. W. Cletcher; U.S. NUCLEAR REGULATORY COMMISSION INFORMATION AND ANALYSES: 158 Operating Experience Feedback Report—Reliability of Safety-Related Steam Turbine-Driven Standby Pumps Used in U.S. Commercial Nuclear Power Plants, J. R. Boardman; 166 Turbine Building Hazards, H. L Ornstein; RECENT DEVELOPMENTS: 169 Reports, Standards, and Safety Guides, D. S. Queener; 175 Proposed Rule Changes as of Dec. 31,1994; ANNOUNCEMENTS: 32 Harvard School of Public Health In-Place Filter Testing Workshop; 134 International Conference on Advances in the Operational Safety of Nuclear Power Plants; 193 30th Tennessee Industries Week; 193 DOE Technical Standards Program 1995 Workshop; 194 Multiphase Flow Experiments and Instrumentation; 180 The Authors; 185 Indexes to Nuclear Safety, Volumes 34 and 35.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

An efficient algorithm for incompressible N-phase flows

We present an efficient algorithm within the phase field framework for simulating the motion of a mixture of N (N⩾2) immiscible incompressible fluids, with possibly very different physical properties such as densities, viscosities, and pairwise surface tensions. The algorithm employs a physical formulation for the N-phase system that honors the conservations of mass and momentum and the second law of thermodynamics. We present a method for uniquely determining the mixing energy density coefficients involved in the N-phase model based on the pairwise surface tensions among the N fluids. Our numerical algorithm has several attractive properties that make it computationally very efficient: (i) it has completely de-coupled the computations for different flow variables, and has also completely de-coupled the computations for the (N−1) phase field functions; (ii) the algorithm only requires the solution of linear algebraic systems after discretization, and no nonlinear algebraic solve is needed; (iii) for each flow variable the linear algebraic system involves only constant and time-independent coefficient matrices, which can be pre-computed during pre-processing, despite the variable density and variable viscosity of the N-phase mixture; (iv) within a time step the semi-discretized system involves only individual de-coupled Helmholtz-type (including Poisson) equations, despite the strongly-coupled phase–field system of fourth spatial order at the continuum level; (v) the algorithm is suitable for large density contrasts and large viscosity contrasts among the N fluids. Extensive numerical experiments have been presented for several problems involving multiple fluid phases, large density contrasts and large viscosity contrasts. In particular, we compare our simulations with the de Gennes theory, and demonstrate that our method produces physically accurate results for multiple fluid phases. We also demonstrate the significant and sometimes dramatic effects of the gravity, density ratios, pairwise surface tensions, and drop sizes on the N-phase configurations and dynamics. The numerical results show that the method developed herein is capable of dealing with N-phase systems with large density ratios, large viscosity ratios, and pairwise surface tensions, and that it can be a powerful tool for studying the interactions among multiple types of fluid interfaces.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Molecular Hydrogen Yields from the Alpha Self-Radiolysis of Nitric Acid Solutions Containing Plutonium or Americium

The yield of molecular hydrogen, as a function of nitric acid concentration, from the a-radiolysis of aerated nitric acid and sulfuric acid mixtures containing plutonium or americium has been investigated. Comparison of experimental measurements with predictions of a Monte Carlo radiation track chemistry model shows that, in addition to scavenging of the hydrated electron, its precursor, and the hydrogen atom, the quenching of excited state water is important in controlling the yield of hydrogen. In addition, increases in solution acidity cause a significant change in the track reactions that can be explained as resulting from scavenging of e aq - by H aq + to form H • . While plutonium has been shown to be an effective scavenger of precursors of molecular hydrogen below 0.1 mol dm-3 nitrate, previously reported effects of plutonium on G(H 2 ) a between 1 and 10 mol dm -3 nitric acid were not reproduced. Modelling results suggest that plutonium is unlikely to effectively compete with nitrate ions in scavenging the precursors of molecular hydrogen at higher nitric acid concentrations and this was confirmed by comparing hydrogen yields from plutonium solutions with those from americium. Finally, comparison between the radionuclide, ion accelerator experiments and model predictions leads to the conclusion that the high dose rate of accelerator studies does not significantly affect the measured hydrogen yield. These reactions provide insight into the important processes for liquors common in the reprocessing of spent nuclear fuel and the storage of highly radioactive liquid waste prior to vitrification.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Deuterium Extraction from Helium with a Vanadium Vacuum Permeator: Commissioning of the Tritium Extraction eXperiment (TEX)

Here, the Tritium Extraction eXperiment (TEX) is a forced-convection lead-lithium (PbLi) loop in the Safety and Tritium Applied Research (STAR) facility at Idaho National Laboratory (INL) with the purpose of providing validation data for the vacuum permeator tritium extraction concept. A vanadium tube of 1000 mm length, 12.7 mm outside diameter, and 0.50 mm wall thickness is installed in the test section of TEX. The installed vanadium tube is characterized to quantify impurity concentrations, surface chemistry, and microstructure to elucidate permeation phenomena observed in experimentation. Herein, the permeation properties of the vanadium tube are characterized by measuring deuterium permeation at 300 °C, 325 °C, and 350 °C at 100 kPa, 125 kPa, and 150 kPa total pressures with 5000 ppm deuterium in helium gas mixture in a once-through flow configuration. The hydrogen isotope permeation through the vanadium tube in the test section is measured with quadrupole mass spectrometers and the hydrogen isotope concentration in the feed and retentate gas stream is measured with gas chromatography. The transient permeation results are modeled with MELCOR-TMAP, a thermal-hydraulic tritium transport code, and compared well with literature data.

70 - PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Community Radiative Transfer Model: Implementing A New Cloud Scattering Database and Developing the Forward Radar Module

The Mie theory is used by many fast RT models to estimate the optical properties of single particles. The Mie theory assumes spherical shapes for ice or snow particles with mixture of air and ice. However, hydrometeors scattering radiation at microwave frequencies have different shapes, sizes, and orientations. Therefore, using Mie theory to determine their optical properties leads to large uncertainties in all-sky radiative transfer calculations. The discrete dipole approximation (DDA) which approximates the optical properties of large objects in terms of discrete dipoles has shown promises in calculating the scattering properties of particles with different shapes in the microwave frequencies. The goal of the research was to enhance the CRTM scattering calculations for frozen hydrometeors in the microwave frequencies using the DDA technique. Given that such optical properties cannot be practically calculated on the fly, pre-computed look-up tables need to be implemented into the fast RT models to calculate the scattering properties of these particles using the DDA technique and the inputs provided by the users. Therefore, we implemented such pre-computed DDA databases into CRTM. In addition to using stand-alone CRTM calculations using collocated ATMS and reanalysis profiles, the data assimilation experiments conducted using the NOAA FV3GFS forecast system will be used to evaluate the scattering improvements. Additionally, we used the backscattering information from the DDA database to implement a radar simulator into CRTM. The radar operators takes advantage of CRTM different modules to calculate clouds absorption and scattering properties. In addition to the forward model both adjoint and tangent linear of the radar simulator are implemented and evaluated as well. The radar simulator is currently being tested within the JEDI/GEOS data assimilation framework to facilitate the assimilation of radar measurements such as CloudSat CPR and GPM DPR into the NASA GEOS model.

Isaac Moradi↗

FCC-hh: The Hadron Collider

Particle physics has arrived at an important moment of its history. The discovery of the Higgs boson, with a mass of 125 GeV, completes the matrix of particles and interactions that has constituted the “Standard Model” for several decades. This model is a consistent and predictive theory, which has so far proven successful at describing all phenomena accessible to collider experiments. However, several experimental facts do require the extension of the Standard Model and explanations are needed for observations such as the abundance of matter over antimatter, the striking evidence for dark matter and the non-zero neutrino masses. Theoretical issues such as the hierarchy problem, and, more in general, the dynamical origin of the Higgs mechanism, do likewise point to the existence of physics beyond the Standard Model. This report contains the description of a novel research infrastructure based on a highest-energy hadron collider with a centre-of-mass collision energy of 100 TeV and an integrated luminosity of at least a factor of 5 larger than the HL-LHC. It will extend the current energy frontier by almost an order of magnitude. The mass reach for direct discovery will reach several tens of TeV, and allow, for example, to produce new particles whose existence could be indirectly exposed by precision measurements during the earlier preceding e+e– collider phase. This collider will also precisely measure the Higgs self-coupling and thoroughly explore the dynamics of electroweak symmetry breaking at the TeV scale, to elucidate the nature of the electroweak phase transition. WIMPs as thermal dark matter candidates will be discovered, or ruled out. As a single project, this particle collider infrastructure will serve the world-wide physics community for about 25 years and, in combination with a lepton collider (see FCC conceptual design report volume 2), will provide a research tool until the end of the 21st century. Collision energies beyond 100 TeV can be considered when using high-temperature superconductors. The European Strategy for Particle Physics (ESPP) update 2013 stated “To stay at the forefront of particle physics, Europe needs to be in a position to propose an ambitious post-LHC accelerator project at CERN by the time of the next Strategy update”. The FCC study has implemented the ESPP recommendation by developing a long-term vision for an “accelerator project in a global context”. This document describes the detailed design and preparation of a construction project for a post-LHC circular energy frontier collider “in collaboration with national institutes, laboratories and universities worldwide”, and enhanced by a strong participation of industrial partners. Now, a coordinated preparation effort can be based on a core of an ever-growing consortium of already more than 135 institutes worldwide. The technology for constructing a high-energy circular hadron collider can be brought to the technology readiness level required for constructing within the coming ten years through a focused R&D programme. The FCC-hh concept comprises in the baseline scenario a power-saving, low-temperature superconducting magnet system based on an evolution of the Nb3Sn technology pioneered at the HL-LHC, an energy-efficient cryogenic refrigeration infrastructure based on a neon-helium (Nelium) light gas mixture, a high-reliability and low loss cryogen distribution infrastructure based on Invar, high-power distributed beam transfer using superconducting elements and local magnet energy recovery and re-use technologies that are already gradually introduced at other CERN accelerators. On a longer timescale, high-temperature superconductors can be developed together with industrial partners to achieve an even more energy efficient particle collider or to reach even higher collision energies.The re-use of the LHC and its injector chain, which also serve for a concurrently running physics programme, is an essential lever to come to an overall sustainable research infrastructure at the energy frontier. Strategic R&D for FCC-hh aims at minimising construction cost and energy consumption, while maximising the socio-economic impact. It will mitigate technology-related risks and ensure that industry can benefit from an acceptable utility. Concerning the implementation, a preparatory phase of about eight years is both necessary and adequate to establish the project governance and organisation structures, to build the international machine and experiment consortia, to develop a territorial implantation plan in agreement with the host-states’ requirements, to optimise the disposal of land and underground volumes, and to prepare the civil engineering project. Such a large-scale, international fundamental research infrastructure, tightly involving industrial partners and providing training at all education levels, will be a strong motor of economic and societal development in all participating nations. The FCC study has implemented a set of actions towards a coherent vision for the world-wide high-energy and particle physics community, providing a collaborative framework for topically complementary and geographically well-balanced contributions. This conceptual design report lays the foundation for a subsequent infrastructure preparatory and technical design phase.

43 PARTICLE ACCELERATORS↗

Effect of subsurface soil moisture variability and atmospheric conditions on methane gas migration in shallow subsurface

We report a major concern resulting from the increased use and production of natural gas has been how to mitigate fugitive greenhouse gas emissions (predominantly methane) from natural gas infrastructure (e.g., leaky shallow pipelines). Subsurface migration and atmospheric loading of methane from pipeline leakage is controlled by source configurations and subsurface soil conditions (e.g., soil heterogeneity and soil moisture) and are further affected by atmospheric conditions (e.g., wind and temperature). However, the transport and attenuation of methane under varying subsurface and atmospheric conditions are poorly understood, making it difficult to estimate leakage fluxes from methane concentration measurements at and above the soil surface. Based on a series of controlled bench-scale experiments using a large porous media tank interfaced with an open-return wind tunnel, this study investigated multiphase processes controlling migration of methane from a point source representing a buried pipeline leaking at fixed flow rate (kg/s) under various saturation and soil-texture conditions. In addition, potential effects of atmospheric boundary controls, wind (0.5 and 2.0 m s -1 ) and temperature (22 and 35 °C), were also examined. Results showed the distinct effects of soil heterogeneity and, to a varying degree, of soil moisture on surface methane concentrations. In addition, results also showed the pronounced effects of wind and, to a lesser degree, of temperature on surface methane concentrations in the presence of varying soil and moisture conditions. The observed subsurface methane profiles were simulated using the multiphase transport simulator TOUGH2-EOS7CA. Observed agreement between measured and simulated data demonstrates that for the conditions studied, multiphase migration of a multicomponent gas mixture (including methane) under density-dependent flow can be adequately represented with a Fickian advection-diffusion (or dispersion) model (ADM) framework. The dominant effect of saturation over the soil texture, could also be inferred from numerical characterization.

09 BIOMASS FUELS↗