Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “interface dynamics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Numerical Study of Lander Engine Plume Impingement on the Surface of Europa

Plume exhaust from lander engines would be of concern when landing on the surface of Europa since it could have detrimental effects on both the landing surface and powered descent vehicle. The plume could also entrain particles and redirect them up toward the landing vehicle, as well as erode and contaminate the surface where science would be conducted. In this work, a numerical methodology is developed and validated to conduct a first-order assessment of individual engine plumes of a potential Europa Lander vehicle. Computational Fluid Dynamics (CFD) is used to solve the flow field inside and immediately downstream of the nozzle, while the Direct Simulation Monte Carlo (DSMC) method is applied further downstream where the flow becomes rarefied. An interface between the two domains is defined where macroscopic flow data is passed from the CFD domain to the DSMC domain, establishing a one-way coupling. Plume pressure and velocity fields, as well as ground heating, pressure and density flux profiles, are obtained at altitudes from 25 m down to 10 m, spanning the final stages of landing. The codes and methodologies used in this study are successfully validated with simulations conducted by Morris et al. of the Apollo Lunar Module Descent Engine (LMDE) exhaust plume impinging onto the lunar surface.

Lam, Rebekah↗

Numerical study of lander engine plume impingement on the surface off Europa

Plume exhaust from lander engines would be of concern when landing on the surface of Europa since it could have detrimental effects on both the landing surface and powered descent vehicle. The plume could also entrain particles and redirect them up toward the landing vehicle, as well as erode and contaminate the surface where science would be conducted. In this work, a numerical methodology is developed and validated to conduct a first-order assessment of individual engine plumes of a potential Europa Lander vehicle. Computational Fluid Dynamics (CFD) is used to solve the flow field inside and immediately downstream of the nozzle, while the Direct Simulation Monte Carlo (DSMC) method is applied further downstream where the flow becomes rarefied. An interface between the two domains is defined where macroscopic flow data is passed from the CFD domain to the DSMC domain, establishing a one-way coupling. Plume pressure and velocity fields, as well as ground heating, pressure and density flux profiles, are obtained at altitudes from 25 m down to 10 m, spanning the final stages of landing. The codes and methodologies used in this study are successfully validated with simulations conducted by Morris et al. [1-3] of the Apollo Lunar Module Descent Engine (LMDE) exhaust plume impinging onto the lunar surface.

Hoey, William↗

Staggered solution procedures for multibody dynamics simulation

The numerical solution procedure for multibody dynamics (MBD) systems is termed a staggered MBD solution procedure that solves the generalized coordinates in a separate module from that for the constraint force. This requires a reformulation of the constraint conditions so that the constraint forces can also be integrated in time. A major advantage of such a partitioned solution procedure is that additional analysis capabilities such as active controller and design optimization modules can be easily interfaced without embedding them into a monolithic program. After introducing the basic equations of motion for MBD system in the second section, Section 3 briefly reviews some constraint handling techniques and introduces the staggered stabilized technique for the solution of the constraint forces as independent variables. The numerical direct time integration of the equations of motion is described in Section 4. As accurate damping treatment is important for the dynamics of space structures, we have employed the central difference method and the mid-point form of the trapezoidal rule since they engender no numerical damping. This is in contrast to the current practice in dynamic simulations of ground vehicles by employing a set of backward difference formulas. First, the equations of motion are partitioned according to the translational and the rotational coordinates. This sets the stage for an efficient treatment of the rotational motions via the singularity-free Euler parameters. The resulting partitioned equations of motion are then integrated via a two-stage explicit stabilized algorithm for updating both the translational coordinates and angular velocities. Once the angular velocities are obtained, the angular orientations are updated via the mid-point implicit formula employing the Euler parameters. When the two algorithms, namely, the two-stage explicit algorithm for the generalized coordinates and the implicit staggered procedure for the constraint Lagrange multipliers, are brought together in a staggered manner, they constitute a staggered explicit-implicit procedure which is summarized in Section 5. Section 6 presents some example problems and discussions concerning several salient features of the staggered MBD solution procedure are offered in Section 7.

Park, K. C.↗

Computer program MCAP-TOSS calculates steady-state fluid dynamics of coolant in parallel channels and temperature distribution in surrounding heat-generating solid

Computer program calculates the steady state fluid distribution, temperature rise, and pressure drop of a coolant, the material temperature distribution of a heat generating solid, and the heat flux distributions at the fluid-solid interfaces. It performs the necessary iterations automatically within the computer, in one machine run.

Lee, A. Y.↗

An experimental investigation of compressor stall using an on-line distortion indicator and signal conditioner

The relation of the steady-state and dynamic distortions and the stall margin of a J85-13 turbojet engine was investigated. A distortion indicator capable of computing two distortion indices was used. A special purpose signal conditioner was also used as an interface between transducer signals and distortion indicator. A good correlation of steady-state distortion and stall margin was established. The prediction of stall by using the indices as instantaneous distortion indicators was not successful. A sensitivity factor that related the loss of stall margin to the turbulence level was found.

Costakis, W. G.↗

The hammer QSD-quick stop device for high speed machining and rubbing

A quick stop device (QSD) was designed for use in orthogonal machining and rubbing experiments. QSD's are used to obtain chip root samples that are representative of the deformation taking place during dynamic (actual) cutting conditions. These 'frozen' specimens are helpful in examining the plastic deformation that occurs in the regions of compression and shear which form the chip; the secondary shear at the tool-chip interface; and the nose ploughing/flank rubbing action which operates on the newly machined surface. The Hammer QSD employs a shear pin mechanism, broken by a flying hammer, which is traveling at the same velocity as the workpiece. The device has been successfully tested up to 6000 sfpm (30.48 m/sec).

Black, J. T.↗

Solutal Convection and Its Effects on Crystal Growth and Segregation in Binary and Pseudo-Binary System with Large Liquidus-Solidus Separation

This research program is composed of theoretical and experimental studies of solutal convection and its effects on crystal growth and segregation in binary and pseudo-binary systems with large liquidus-solidus separation. The theoretical program has resulted in the development of a transient simulation of the growth of concentrated alloys in microgravity and has been used to study the dynamics of GeSi, PbSnTe, HgCdTe growth. Finite element analysis has also been developed for studying the interactions of buoyancy-driven convection in the melt caused by temperature and concentration variations with melt-solid interface morphology and alloy segregation in the grown crystal. These calculations are being compared directly to experimental measurements of segregation and interface shape for GeSi growth and GaGe growth. The results for SiGe indicate that careful design of the thermal system can result in almost diffusion-controlled growth on Earth because of the stablizing influence of the concentration gradient ahead of the solidification front.

Brown, R. A.↗

Numerical modeling of spray combustion with an advanced VOF method

This paper summarizes the technical development and validation of a multiphase computational fluid dynamics (CFD) numerical method using the volume-of-fluid (VOF) model and a Lagrangian tracking model which can be employed to analyze general multiphase flow problems with free surface mechanism. The gas-liquid interface mass, momentum and energy conservation relationships are modeled by continuum surface mechanisms. A new solution method is developed such that the present VOF model can be applied for all-speed flow regimes. The objectives of the present study are to develop and verify the fractional volume-of-fluid cell partitioning approach into a predictor-corrector algorithm and to demonstrate the effectiveness of the present approach by simulating benchmark problems including laminar impinging jets, shear coaxial jet atomization and shear coaxial spray combustion flows.

Chen, Yen-Sen↗

Atomization simulations using an Eulerian-VOF-Lagrangian method

This paper summarizes the technical development and validation of a multiphase computational fluid dynamics (CFD) numerical method using the volume-of-fluid (VOF) model and a Lagrangian tracking model which can be employed to analyze general multiphase flow problems with free surface mechanism. The gas-liquid interface mass, momentum and energy conservations are modeled by continuum surface mechanisms. A new solution method is developed such that the present VOF model can be applied for all-speed flow regimes. The objectives of the present study are to develop and verify the fractional volume-of-fluid cell partitioning approach into a predictor-corrector algorithm and to demonstrate the effectiveness of the present innovative approach by simulating benchmark problems including the coaxial jet atomization.

Chen, Yen-Sen↗

A Frequency-Domain Substructure System Identification Algorithm

A new frequency-domain system identification algorithm is presented for system identification of substructures, such as payloads to be flown aboard the Space Shuttle. In the vibration test, all interface degrees of freedom where the substructure is connected to the carrier structure are either subjected to active excitation or are supported by a test stand with the reaction forces measured. The measured frequency-response data is used to obtain a linear, viscous-damped model with all interface-degree of freedom entries included. This model can then be used to validate analytical substructure models. This procedure makes it possible to obtain not only the fixed-interface modal data associated with a Craig-Bampton substructure model, but also the data associated with constraint modes. With this proposed algorithm, multiple-boundary-condition tests are not required, and test-stand dynamics is accounted for without requiring a separate modal test or finite element modeling of the test stand. Numerical simulations are used in examining the algorithm's ability to estimate valid reduced-order structural models. The algorithm's performance when frequency-response data covering narrow and broad frequency bandwidths is used as input is explored. Its performance when noise is added to the frequency-response data and the use of different least squares solution techniques are also examined. The identified reduced-order models are also compared for accuracy with other test-analysis models and a formulation for a Craig-Bampton test-analysis model is also presented.

Blades, Eric L.↗

Sensitivity of Force Specifications to the Errors in Measuring the Interface Force

Force-Limited Random Vibration Testing has been applied in the last several years at the NASA Goddard Space Flight Center (GSFC) and other NASA centers for various programs at the instrument and spacecraft level. Different techniques have been developed over the last few decades to estimate the dynamic forces that the test article under consideration will encounter in the flight environment. Some of these techniques are described in the handbook, NASA-HDBK-7004, and the monograph, NASA-RP-1403. This paper will show the effects of some measurement and calibration errors in force gauges. In some cases, the notches in the acceleration spectrum when a random vibration test is performed with measurement errors are the same as the notches produced during a test that has no measurement errors. The paper will also present the results Of tests that were used to validate this effect. Knowing the effect of measurement errors can allow tests to continue after force gauge failures or allow dummy gauges to be used in places that are inaccessible to a force gage.

Worth, Daniel↗

Visualization of a Capsule Entry Vehicle Reaction-Control System (RCS) Thruster

Planar laser-induced fluorescence (PLIF) was used to visualize the reaction control system (RCS) jet flow emanating from the aft-body of an Apollo-geometry capsule test article in the NASA Langley Research Center 31-Inch Mach 10 Air wind tunnel. The RCS jet was oriented normal to the aft surface of the model and had a nominal Mach number of 2.94. The composition of the jet gas by mass was 95% nitrogen (N2) and 5% nitric oxide (NO). The RCS jet flowrate varied between zero and 0.5 standard liters per minute and the angle of attack and tunnel stagnation pressure were also varied. PLIF was used to excite the NO molecules for flow visualization. These flow visualization images were processed to determine the trajectory and to quantify the flapping of the RCS jet. The spatial resolution of the jet trajectory measurement was about 1 mm and the single-shot precision of the measurement was estimated to be 0.02 mm in the far field of the jet plume. The jet flapping, measured by the standard deviation of the jet centerline position was as large as 0.9 mm, while the jet was 1.5-4 mm in diameter (full width at half maximum). Schlieren flow visualization images were obtained for comparison with the PLIF. Surface pressures were also measured and presented. Virtual Diagnostics Interface (VIDI) technology developed at NASA Langley was used to superimpose and visualize the data sets. The measurements demonstrate some of the capabilities of the PLIF method while providing a test case for computational fluid dynamics (CFD) validation.

Danehy, P. M.↗

Using Apex To Construct CPM-GOMS Models

process for automatically generating computational models of human/computer interactions as well as graphical and textual representations of the models has been built on the conceptual foundation of a method known in the art as CPM-GOMS. This method is so named because it combines (1) the task decomposition of analysis according to an underlying method known in the art as the goals, operators, methods, and selection (GOMS) method with (2) a model of human resource usage at the level of cognitive, perceptual, and motor (CPM) operations. CPM-GOMS models have made accurate predictions about behaviors of skilled computer users in routine tasks, but heretofore, such models have been generated in a tedious, error-prone manual process. In the present process, CPM-GOMS models are generated automatically from a hierarchical task decomposition expressed by use of a computer program, known as Apex, designed previously to be used to model human behavior in complex, dynamic tasks. An inherent capability of Apex for scheduling of resources automates the difficult task of interleaving the cognitive, perceptual, and motor resources that underlie common task operators (e.g., move and click mouse). The user interface of Apex automatically generates Program Evaluation Review Technique (PERT) charts, which enable modelers to visualize the complex parallel behavior represented by a model. Because interleaving and the generation of displays to aid visualization are automated, it is now feasible to construct arbitrarily long sequences of behaviors. The process was tested by using Apex to create a CPM-GOMS model of a relatively simple human/computer-interaction task and comparing the time predictions of the model and measurements of the times taken by human users in performing the various steps of the task. The task was to withdraw $80 in cash from an automated teller machine (ATM). For the test, a Visual Basic mockup of an ATM was created, with a provision for input from (and measurement of the performance of) the user via a mouse. The times predicted by the automatically generated model turned out to approximate the measured times fairly well (see figure). While these results are promising, there is need for further development of the process. Moreover, it will also be necessary to test other, more complex models: The actions required of the user in the ATM task are too sequential to involve substantial parallelism and interleaving and, hence, do not serve as an adequate test of the unique strength of CPM-GOMS models to accommodate parallelism and interleaving.

John, Bonnie↗

Microscale Processes Determining Macroscale Evolution of Magnetic Flux Tubes along Earth’s Magnetopause

An important process affecting solar wind-Earth’s magnetosphere coupling is non-steady dayside magnetic reconnection, observationally evidenced by a flux-transfer-event (FTE) that shows a bipolar variation of the magnetic field component normal to the magnetopause. FTEs often consist of two interlinked flux tubes, but, local kinetic processes between the flux tubes are not understood in the context of the FTE structuring, evolution, and impact. An FTE observed by MMS on 18 December 2017 consisted of two flux tubes of different topology. One includes field lines with ends connected to the northern and southern hemispheres while the other includes field lines with both ends connected to the magnetosheath. Reconnection occurring at the flux-tube interface indicates how interacting flux tubes evolve into a flux rope with helical magnetic topology that is either closed or open. This study demonstrates a new aspect of how micro-to meso-scale dynamics occurring within FTEs determines their macroscale characteristics and evolution.

Solar-terrestrial interactions↗

A SIMULINK environment for flight dynamics and control analysis: Application to the DHC-2 Beaver. Part 1: Implementation of a model library in SIMULINK. Part 2: Nonlinear analysis of the Beaver autopilot

The design of advanced Automatic Aircraft Control Systems (AACS's) can be improved upon considerably if the designer can access all models and tools required for control system design and analysis through a graphical user-interface, from within one software environment. This MSc-thesis presents the first step in the development of such an environment, which is currently being done at the Section for Stability and Control of Delft University of Technology, Faculty of Aerospace Engineering. The environment is implemented within the commercially available software package MATLAB/SIMULINK. The report consists of two parts. Part I gives a detailed description of the AACS design environment. The heart of this environment is formed by the SIMULINK implementation of a nonlinear aircraft model in block-diagram format. The model has been worked out for the old laboratory aircraft of the Faculty, the De Havilland DHC-2 'Beaver', but due to its modular structure, it can easily be adapted for other aircraft. Part I also describes MATLAB programs which can be applied for finding steady-state trimmed-flight conditions and for linearization of the aircraft model, and it shows how the built-in simulation routines of SIMULINK have been used for open-loop analysis of the aircraft dynamics. Apart from the implementation of the models and tools, a thorough treatment of the theoretical backgrounds is presented. Part II of this report presents a part of an autopilot design process for the 'Beaver' aircraft, which clearly demonstrates the power and flexibility of the AACS design environment from part I. Evaluations of all longitudinal and lateral control laws by means of nonlinear simulations are treated in detail. The AACS design environment from part I proved to be a very useful tool for designing the control laws of the 'Beaver' autopilot within a very tight time-schedule. The autopilot design process itself will be used as a guideline for future AACS research at the Faculty of Aerospace Engineering. Flight tests of the 'Beaver' autopilot, done after evaluating the control laws in the SIMULINK package, proved to be quite successful. In the future, the AACS design package will evolve into a standardized, integrated design environment which can be applied to virtually any type of aircraft. The AACS design cycle will be shortened further by developing tools for automatically porting control laws from the MATLAB/SIMULINK environment to a piloted real-time flight simulator and the Flight Control Computers of the aircraft.

Flight Control System Design↗

Several recent findings concerning the dynamics of the earth's magnetotail

Several recent results concerning the nature of earth's magnetotail are briefly reviewed. These observational findings include: (1) the three-dimensional character of the plasma sheet via a comprehensive survey of proton bulk flows, (2) a region of earthward-flowing plasmas at the interfaces of the plasma sheet and magnetotail lobes during magnetic substorm recovery, and (3) the signature of electrostatic acceleration for protons within the jetting plasmas from magnetotail fireballs.

Frank, L. A.↗

Analysis of Smart Composite Structures Including Debonding

Smart composite structures with distributed sensors and actuators have the capability to actively respond to a changing environment while offering significant weight savings and additional passive controllability through ply tailoring. Piezoelectric sensing and actuation of composite laminates is the most promising concept due to the static and dynamic control capabilities. Essential to the implementation of these smart composites are the development of accurate and efficient modeling techniques and experimental validation. This research addresses each of these important topics. A refined higher order theory is developed to model composite structures with surface bonded or embedded piezoelectric transducers. These transducers are used as both sensors and actuators for closed loop control. The theory accurately captures the transverse shear deformation through the thickness of the smart composite laminate while satisfying stress free boundary conditions on the free surfaces. The theory is extended to include the effect of debonding at the actuator-laminate interface. The developed analytical model is implemented using the finite element method utilizing an induced strain approach for computational efficiency. This allows general laminate geometries and boundary conditions to be analyzed. The state space control equations are developed to allow flexibility in the design of the control system. Circuit concepts are also discussed. Static and dynamic results of smart composite structures, obtained using the higher order theory, are correlated with available analytical data. Comparisons, including debonded laminates, are also made with a general purpose finite element code and available experimental data. Overall, very good agreement is observed. Convergence of the finite element implementation of the higher order theory is shown with exact solutions. Additional results demonstrate the utility of the developed theory to study piezoelectric actuation of composite laminates with pre-existing debonding. Significant changes in the modes shapes and reductions in the control authority result due to partially debonded actuators. An experimental investigation addresses practical issues, such as circuit design and implementation, associated with piezoelectric sensing and actuation of composite laminates. Composite specimens with piezoelectric transducers were designed, constructed and tested to validate the higher order theory. These specimens were tested with various stacking sequences, debonding lengths and gains for both open and closed loop cases. Frequency changes of 15% and damping on the order of more than 20% of critical damping, via closed loop control, was achieved. Correlation with the higher order theory is very good. Debonding is shown to adversely affect the open and closed loop frequencies, damping ratios, settling time and control authority.

Chattopadhyay, Aditi↗

A case study for the real-time experimental evaluation of the VIPER microprocessor

An experiment to evaluate the applicability of the Verifiable Integrated Processor for Enhanced Reliability (VIPER) microprocessor to real time control is described. The VIPER microprocessor was invented by the Royal Signals and Radar Establishment (RSRE), U.K., and is an example of the use of formal mathematical methods for developing electronic digital systems with a high degree of assurance on the system design and implementation correctness. The experiment consisted of selecting a control law, writing the control law algorithm for the VIPER processor, and providing real time, dynamic inputs into the processor and monitoring the outputs. The control law selected and coded for the VIPER processor was the yaw damper function of an automatic landing program for a 737 aircraft. The mechanisms for interfacing the VIPER Single Board Computer to the VAX host are described. Results include run time experiences, performance evaluation, and comparison of VIPER and FORTRAN yaw damper algorithm output for accuracy estimation.

Carreno, Victor A.↗