Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high performance visualization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS2013

Commercial Off-The-Shelf (COTS) Graphics Processing Board (GPB) Radiation Test Evaluation Report

Large round trip communications latency for deep space missions will require more onboard computational capabilities to enable the space vehicle to undertake many tasks that have traditionally been ground-based, mission control responsibilities. As a result, visual display graphics will be required to provide simpler vehicle situational awareness through graphical representations, as well as provide capabilities never before done in a space mission, such as augmented reality for in-flight maintenance or Telepresence activities. These capabilities will require graphics processors and associated support electronic components for high computational graphics processing. In an effort to understand the performance of commercial graphics card electronics operating in the expected radiation environment, a preliminary test was performed on five commercial offthe- shelf (COTS) graphics cards. This paper discusses the preliminary evaluation test results of five COTS graphics processing cards tested to the International Space Station (ISS) low earth orbit radiation environment. Three of the five graphics cards were tested to a total dose of 6000 rads (Si). The test articles, test configuration, preliminary results, and recommendations are discussed.

Salazar, George A.↗
NASA NTRSDate not supplied

NASA’s Moon Trek Portal: New Capabilities Supporting Mission Planning and Engagement

Introduction: NASA’s Moon Trek (https://trek.nasa.gov/moon/) is one of a growing number of interactive, browser-based, online portals for planetary data visualization and analysis produced by NASA’s Solar System Treks Project (SSTP). Moon Trek continues to be enhanced with new data and new capabilities enabling it to facilitate the planning and conducting of upcoming lunar missions by NASA, its commercial partners, and its international partners, as well as advancing its role as a valuable outreach tool. A Comprehensive Online Web Portal: Developed at NASA’s Jet Propulsion Laboratory (JPL) and managed as a project of NASA’s Solar System Exploration Research Virtual Institute (SSERVI) at NASA Ames Research Center, Moon Trek is a browser-based web portal. The portal provides easy-to-use tools for browsing, data layering, data product blending, and feature search among thousands of data products covering topography, mineralogy, elemental abundance, geology, and much more. Visualizations are provided in var-ious map projections, interactive 3D viewing, and in virtual reality. Using an in-house stereo workflow, SSTP is able to produce new NAC-based high-resolution mosaics and DEMs. Diverse Applications for Lunar Exploration: Baseline analytic tools available to all users include dis-tance measurement, elevation profiling, sun angle calculation, and 3D print file generation. More advanced account-level tools allow users to perform more computationally intensive analyses. These include ray-traced lighting analysis for user-specified areas over user-specified time/date ranges and time intervals, electro-static surface potential analysis, subsetting of large data products, slope analysis, and Lunar Laser Ranging geometry calculation. Artificial intelligence (AI) and ma-chine learning (ML) based tools have been implemented for crater detection and hazard analysis, boulder detection and hazard analysis, and rockfall detection. New Tools Facilitating Exploration: Additional, new tools have recently been added and others are in development, offering even greater functionality in con-ducting analyses of potential landing sites and areas of surface operations. The new Line-of-Sight tool facilitates communications planning between locations on the lunar surface, between any given site on the lunar surface and a specified ground station on the Earth, and between a site on the lunar surface and a relay asset in lunar orbit, all taking into account local lunar topography. The new Data Plotter tool provides both tabular and graphical representations of pixel values along a user specified path for a growing number of data products. The new NAC Finder tool will identify and pro-vide access to NAC images that intersect a user-defined path or bounded area. The SSTP development team is looking to leverage the capabilities of its existing AI and ML crater, boulder, and rockfall detection and analysis tools, and extend that technology to a generalized feature detector that can be trained on instances of specific types of landforms and then search the lunar surface for more examples of such features. New traverse planning tools are being developed with use cases in generalized concept studies and specific mission planning in mind. These will facilitate finding optimal traverse paths based on constraints such as slope, lighting, hazard avoidance, and communications. These will be complemented by new traverse visualization capabilities. Users will be able to interactively ride along with a rover, examining 3D views of the terrain while adjusting camera height and viewing angle along with selecting different data layer overlays to drape across the terrain. Engaging the Public: The capabilities being developed for mission planning are being leveraged to further enhance Moon Trek’s proven utility as a valuable public outreach resource. This includes providing multiple lev-els of engagement with different points of entry. At its simplest level, promoting understanding through visualization, media and the public will be able to easily visualize and conduct their own exploration of lunar sites targeted by NASA and its partners. For a more in-depth experience, we are working with our stakeholders to promote understanding through interaction by extend-ing our current landing site and traverse analysis capabilities, making simplified access to these tools available to those who want to explore more deeply key factors in planning a mission through interactive and possibly even gamified experiences. The highest degree of public outreach, focusing on engagement through scientific participation, could be achieved through our work with missions and the NASA Office of the Chief Scientist on Moon Trek’s extension as a tool with specialized capabilities for facilitating citizen science. In such scenarios, participants become members of extended mis-sion science teams, using dedicated and integrated interfaces to analyze mission data to help answer questions key to lunar science and exploration. We are work-ing with NASA’s Office of Communications, museums, planetariums, and the media to help them easily integrate accurate, detailed visualizations of NASA’s lunar destinations and exploration into their content/productions and to engage diverse audiences in diverse venues.

Moon Trek↗
DOE OSTI2023

Final Report on Development of Microwave Resonant Cavity Transducer for Fluid Flow Sensing: Development of Microwave Cavity Flow Meter for Advanced Reactor High Temperature Fluids

We are investigating a microwave resonant cavity transducer for flow sensing in the vessel of a high temperature fluid advanced reactor (AR), such as a molten salt cooled reactor (MSCR) or a sodium fast reactor (SFR). This transducer is a hollow metallic cylindrical cavity, with one of the flat walls of the cylinder flexible enough to undergo microscopic deflection due to dynamic fluid pressure. Membrane deflection leads to a shift in the microwave resonant frequency, which can be detected with a spectrum analyzer. We have developed a continuum electromechanics model of the microwave resonant cavity transducer performance. The deflection of the membrane is calculated using equations from the theory of plates and shells for deflection of radially constrained thin circular disk under uniform load. The microwave frequency shift is calculated using the equations from the microwave cavity perturbation theory. The transducer model was validated with proof-of-concept experimental data of water flow sensing with a Brass 360 right circular cylinder with 22.2mm diameter and 203µm thick wall. The cavity was excited through a subwavelength hole in TE 011 mode with resonant frequency f ≈ 17.8GHz. Subsequently, we have performed a preliminary proof-of-principle test of flow sensing in high temperature liquid sodium in environment. For this test, we have developed a cylindrical resonator with the same dimensions as for the Brass 360 cavity. The resonator for high temperature liquid sodium test was machined from stainless steel 316 and electroplated with silver on the interior surfaces. We have also developed and insertion probe consisting of a 50cm WR-42 brass waveguide enclosed in a protective SS316 tube. The cavity was excited through a subwavelength hole on the side of the wall of the cylinder in the TE 011 mode with resonant frequency f ≈ 17.8GHz. The liquid sodium setup consists of a cylindrical vessel with a center feed line, where a transducer inserted through the top cap of the vessel measures velocity of the impinging liquid jet. The sodium flow sensing study was performed in a liquid sodium vessel at 340°C temperature and ambient pressure. The flow rate was changed by varying sodium pump power, and a frequency shift of several hundred kHz was observed. The transducer was removed after 70 days of testing. No visual damage was observed, and the electromagnetic response remained the same. As a calibration experiment, we have assembled a water vessel with a center feed, and with dimensions similar to those of the liquid sodium setup. Water flow sensing was performed before and after liquid sodium test. The responses in both cases are similar and agree with COMSOL computer simulations. Because long-term (multi-year) experimental tests of transducer resilience to harsh environment are not practical, we have developed a probabilistic model of creep to estimate transducer resilience to the harsh environment. The probabilistic model considers diffusion creep under the condition of high temperature and low stress, where the stress and temperature are allowed to be random variables with Gaussian distributions. Using the probabilistic model, we estimate inelastic membrane deflections due to creep for several temperature ranges. We conclude that for temperatures less than 650°C, creep has negligible long-term effect on the transducer performance.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1985

Fast laser-induced aerosol formation for visualization of gas flows

A technique for aerosol seeding of gas flows by laser-induced particle formation is demonstrated using a pulsed Nd:YAG laser (1.06 microns) for optical breakdown of a mixture of SF6 and H2 in an inert carrier gas. It is noted that, contrary to the smoke-wire approach, the laser-induced particles form first in zones of high turbulence, since mixing enhances coagulation. The method also allows seeding to be performed in locations hardly accessible otherwise and is mechanically nonintrusive. Finally, a study of the mixture and the breakdown effects indicates that for H2:SF6 ratios between 3:1 and 15:1 the particle formation is only limited by the physics of the gas/particle conversion.

Hassa, C.↗
DOE OSTI2021

A catalogue of white dwarfs in Gaia EDR3

ABSTRACT We present a catalogue of white dwarf candidates selected from Gaia Early Data Release 3 (EDR3). We applied several selection criteria in absolute magnitude, colour, and Gaia quality flags to remove objects with unreliable measurements while preserving most stars compatible with the white dwarf locus in the Hertzsprung–Russell diagram. We then used a sample of over 30 000 spectroscopically confirmed white dwarfs and contaminants from the Sloan Digital Sky Survey (SDSS) to map the distribution of these objects in the Gaia absolute magnitude–colour space. Finally, we adopt the same method presented in our previous work on Gaia Data Release 2 (DR2) to calculate a probability of being a white dwarf (PWD) for ≃1.3 million sources that passed our quality selection. The PWD values can be used to select a sample of ${\simeq} 359\,000$ high-confidence white dwarf candidates. We calculated stellar parameters (effective temperature, surface gravity, and mass) for all these stars by fitting Gaia astrometry and photometry with synthetic pure-H, pure-He, and mixed H–He atmospheric models. We estimate an upper limit of 93 per cent for the overall completeness of our catalogue for white dwarfs with G ≤ 20 mag and effective temperature (Teff) > 7000 K, at high Galactic latitudes (|b| > 20°). Alongside the main catalogue we include a reduced proper motion extension containing ${\simeq} 10\,200$ white dwarf candidates with unreliable parallax measurements that could, however, be identified on the basis of their proper motion. We also performed a cross-match of our catalogues with SDSS Data Release 16 (DR16) spectroscopy and provide spectral classification based on visual inspection for all resulting matches.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2015

Numerical Modeling of the Lake Mary Road Bridge for Foundation Reuse Assessment

This project uses numerical techniques to assess the structural integrity and capacity of the bridge foundations and, as a result, reduces the risk associated with reusing the same foundation for a new superstructure. Nondestructive test methods of different types were used in combination with the numerical modeling and analysis. The onsite tests included visual inspection, tomography, ground penetrating radar, drilling boreholes and coreholes, and the laboratory tests on recovered samples. The results were utilized to identify the current geometry of the structure with foundation, including the hidden geometry of the abutments and piers, and soil and foundation material properties. This data was used to build the numerical models and run computational analyses on a high performance computer cluster to assess the structural integrity of the bridge and foundations including the suitability of the foundation for reuse with a new superstructure and traffic that will increase the load on the foundations. Computational analysis is more cost-effective and gives an advantage of getting more detailed knowledge about the structural response. It also enables to go beyond non-destructive testing and find the failure conditions without destroying the structure under consideration.

foundation reuse↗
DOE OSTI2017

Advanced Fossil Energy Separations and Analysis Research – Thermal Desorption Using Spouted Beds

Mercury and other contaminants in emissions from coal-fired power plants are of interest due to the cost associated with capture and disposal of toxic mercury species. It had recently been postulated in the fossil energy community that spouted beds may be a viable coal pre-treatment technique for thermal desorption of mercury. Spouted beds have the potential to be a near-ideal solid-gas contactor for desorption of mercury species, especially with a few proposed design changes specific for this application. Introduction of draft tubes for spouted beds has addressed some issues with scale-up to better handle the throughput and particle size found in coal-fired power plants. In Phase I, Mainstream Engineering invented and developed a Venturi draft tube spouted bed (VDTSB) to enable process scale-up with fine coal particles and to improve heat and mass transfer. The VDTSB concept increases suction at the bottom of the bed to better entrain material (and reduce the propensity for bridging) at the bottom of the conical vessel. The main advantages of this patent-pending approach are the ability to accept a wide range of coal particle sizes, good heat/mass transfer, process scalability, and robustness. The desorber design was optimized through bed flow visualization experiments; these experiments demonstrated the increased throughput and ease of process scale-up. A high-temperature pilot-scale VDTSB desorber system was designed, fabricated, commissioned, and tested. The heat and mass transfer rates with the VDTSB were measured and compared to a baseline spouted bed with and without a conventional straight draft tube. Pilot-scale VDTSB system performance tests were completed with the Energy and Environmental Research Center (EERC) to measure the rate of mercury desorption over a range of pulverized coal particle sizes, bed temperatures, and reactor geometry. Based on performance results, an initial technoeconomic analysis (TEA) was completed to estimate the cost reduction for emissions treatment compared to current flue-gas mercury capture systems. The following was accomplished in Phase I: Developed scalable design correlations for high-throughput spouted bed systems; Determined cycle time distribution (CTD) and turnover time for straight and Venturi draft tube spouted beds, and showed the VDTSB had lower cycle time (faster turnover) than the straight draft tube (SDT); Reduced weighted-average turnover time by 14% to 43% with Venturi draft tube; narrowed the CTD by up to 75%; Measured heat and mass transfer within the pilot-scale VDTSB desorber and showed that the highest heat transfer rate was 2.98 kW/m 2 ·s with 400 µm particles at a 10 L/min motive gas flowrate; Measured mercury (Hg) desorption rate for lignite, bituminous, and subbituminous coal at 200 °C, 225 °C, 250 °C and 275 °C; Achieved 5.6×10 -10 kg/m 2 -h, 2.6×10 -10 kg/m 2 -h, and 6.5×10 -11 kg/m 2 -h Hg removal rates for lignite, bituminous, and sub-bituminous coals, respectively with no loss in volatile matter and an increase in heating value due to a reduction in moisture content; The unoptimized VDTSB pilot desorber decreased the total mercury concentration of lignite and bituminous coal tests by 61% (dry basis). The subbituminous Powder River Basin (PRB) coal showed a reduction of 18%; Based on our TEA of coal-fired power plants, implementing the VDTSB for coal pretreatment could reduce the mercury capture capital and operating expenses by 36% and 38%, respectively, which exceeded the target goal of 25% reduction; A patent application was prepared, and the results were presented at the 2017 AIChE Annual Meeting (Minneapolis, MN).

20 FOSSIL-FUELED POWER PLANTS↗
DOE OSTI2016

Making Advanced Scientific Algorithms and Big Scientific Data Management More Accessible

Synchrotrons such as the Advanced Light Source (ALS) at Lawrence Berkeley National Laboratory are known as user facilities. They are sources of extremely bright X-ray beams, and scientists come from all over the world to perform experiments that require these beams. As the complexity of experiments has increased, and the size and rates of data sets has exploded, managing, analyzing and presenting the data collected at synchrotrons has been an increasing challenge. The ALS has partnered with high performance computing, fast networking, and applied mathematics groups to create a"super-facility", giving users simultaneous access to the experimental, computational, and algorithmic resources to overcome this challenge. This combination forms an efficient closed loop, where data despite its high rate and volume is transferred and processed, in many cases immediately and automatically, on appropriate compute resources, and results are extracted, visualized, and presented to users or to the experimental control system, both to provide immediate insight and to guide decisions about subsequent experiments during beam-time. In this paper, We will present work done on advanced tomographic reconstruction algorithms to support users of the 3D micron-scale imaging instrument (Beamline 8.3.2, hard X-ray micro-tomography).

97 MATHEMATICS AND COMPUTING↗
NASA NTRS1981

Automated pilot advisory system test and evaluation at Manassas Municipal Airport

In cooperation with the Federal Aviation Administration, NASA developed an experimental automated pilot advisory system (APAS) to provide airport and air traffic advisories at high density uncontrolled airports. The APAS concept is to utilize low cost automated systems to provide the necessary information for pilots to more safely plan and execute approach and landing at uncontrolled high density airports. The system is designed to be a natural extension of the procedural visual flight rules system used at uncontrolled airports and, as an advisory system, will enhance the "see-and-be-seen" rule and an evaluation of the APAS concept was obtained from pilots who used the system at the Manassas, Virginia airport. These evaluations and the system performance are presented.

Parks, J. L., Jr.↗
NASA NTRS2000

Computer Modeling of Real-Time Dynamic Lighting

Space Station tasks involve procedures that are very complex and highly dependent on the availability of visual information. In many situations, cameras are used as tools to help overcome the visual and physical restrictions associated with space flight. However, these cameras are effected by the dynamic lighting conditions of space. Training for these is conditions is necessary. The current project builds on the findings of an earlier NRA funded project, which revealed improved performance by humans when trained with computer graphics and lighting effects such as shadows and glare.

Maida, James C.↗
NASA NTRS2008

Visualization of Flowfield Modification by RCS Jets on a Capsule Entry Vehicle

Nitric oxide planar laser-induced fluorescence (NO PLIF) has been used to visualize the flow on the aft-body of an entry capsule having an activated RCS jet in NASA Langley Research Center's 31-Inch Mach 10 wind tunnel facility. A capsule shape representative of the Apollo command module was tested. These tests were performed to demonstrate the ability of the PLIF method to visualize RCS jet flow while providing some preliminary input to NASA's Orion Vehicle design team. Two different RCS nozzle designs - conical and contoured - were tested. The conical and contoured nozzles had area ratios of 13.4 and 22.5 respectively. The conical nozzle had a half-angle of 10 . Low- and high-Reynolds number cases were investigated by changing the tunnel stagnation pressure from 350 psi to 1300 psi, resulting in freestream Reynolds numbers of 0.56 and 1.8 million per foot respectively. For both of these cases, three different jet plenum pressures were tested (nominally 56, 250 and 500 psi). A single angle-of-attack was investigated (24 degrees). NO PLIF uses an ultraviolet laser sheet to interrogate a slice in the flow containing seeded NO; this UV light excites fluorescence from the NO molecules which is detected by a high-speed digital camera. The system has spatial resolution of about 200 microns (2 pixel blurring) and has flow-stopping time resolution (approximately 1 microsecond). NO was seeded into the flow two different ways. First, the RCS jet fluid was seeded with approximately 1-5% NO, with the balance N2. This allowed observation of the shape, structure and trajectory of the RCS jets. Visualizations of both laminar and turbulent flow jet features were obtained. Visualizations were obtained with the tunnel operating at Mach 10 and also with the test section held at a constant pressure similar to the aftbody static pressure (0.04 psi) obtained during tunnel runs. These two conditions are called "tunnel on" and "tunnel off" respectively. Second, the forebody flow was seeded with a very low flowrate (<100 standard cubic centimeters per minute) of pure NO. This trace gas was entrained into and allowed visualization of the shear layer forming between the expansion fan on the shoulder of the model and the recirculating separated flow in the wake of the model. This shear layer was observed to be laminar in the absence of the RCS jet operation and turbulent above a certain RCS jet flowrate. Furthermore, the operation of the RCS jet is seen to push the shear layer out away from the model, with a higher jet pressures resulting in larger deflections. Figures show some data from this test, partially processed. In the final paper, these images will be processed and rendered on a three dimensional visualization of the test hardware for clearer visualization and interpretation of the flowfields.

Danehy, P. M.↗
DOE OSTI2024

Flame Flashback Investigations in Hydrogen-Enriched Low Swirl Burner using High-Speed Hydroxyl Planar Laser-Induced Fluorescence

Hydrogen/ Hydrogen-rich flame is a potential strategy to reduce carbon emissions for the development of next-generation lean premixed combustors. However, the higher flashback propensity with hydrogen-enrichment owing to faster chemical kinetics is one of the key challenges in existing natural gas turbine combustors. In this study, the fundamentals of stabilized flame dynamics and flashback events in a premixed low swirl burner (LSB) configuration are visualized experimentally using nanosecond (ns)-based high-speed hydroxyl radical planar laser-induced fluorescence (OH-PLIF). The LSB has an optically accessible pre-mixing tube allowing laser diagnostic investigation of flashback events. The inlet conditions are varied systematically with respect to pre-mixer velocities, flame equivalence ratio (ϕ), and hydrogen content and OH-PLIF characterization is performed in stable flame at 20 kHz repetition rate. An increase in flashback propensity is observed with increasing ϕ, hydrogen content, and decreasing V via detailed investigation of flame lift-off length (L) above the burner rim. Flashback ϕ investigations show an expected linearly increasing trend with decreasing hydrogen content and increasing V for each swirler studied and the results agree well with detailed L investigations in stable flame configuration. The propagating flame anchored likely on the back side of the perforated plate within 30-40 ms of the entrance forming the distorted conical flame front.

Parajuli, Pradeep↗
DOE OSTI2017

Quantitative visualization of synchronized insulin secretion from 3D-cultured cells

Quantitative visualization of synchronized insulin secretion was performed in an isolated rat pancreatic islet and a spheroid of rat pancreatic beta cell line using a method of video-rate bioluminescence imaging. Video-rate images of insulin secretion from 3D-cultured cells were obtained by expressing the fusion protein of insulin and Gaussia luciferase (Insulin-GLase). A subclonal rat INS-1E cell line stably expressing Insulin-GLase, named iGL, was established and a cluster of iGL cells showed oscillatory insulin secretion that was completely synchronized in response to high glucose. Furthermore, we demonstrated the effect of an antidiabetic drug, glibenclamide, on synchronized insulin secretion from 2D- and 3D-cultured iGL cells. The amount of secreted Insulin-GLase from iGL cells was also determined by a luminometer. Thus, our bioluminescence imaging method could generally be used for investigating protein secretion from living 3D-cultured cells. In addition, iGL cell line would be valuable for evaluating antidiabetic drugs. - Highlights: • An imaging method for protein secretion from 3D-cultured cells was established. • The fused protein of insulin to GLase, Insulin-GLase, was used as a reporter. • Synchronous insulin secretion was visualized in rat islets and spheroidal beta cells. • A rat beta cell line stably expressing Insulin-GLase, named iGL, was established. • Effect of an antidiabetic drug on insulin secretion was visualized in iGL cells.

60 APPLIED LIFE SCIENCES↗
NASA NTRS1991

High performance computing system for flight simulation at NASA Langley

The computer architecture and components used in the NASA Langley Advanced Real-Time Simulation System (ARTSS) are briefly described and illustrated with diagrams and graphs. Particular attention is given to the advanced Convex C220 processing units, the UNIX-based operating system, the software interface to the fiber-optic-linked Computer Automated Measurement and Control system, configuration-management and real-time supervisor software, ARTSS hardware modifications, and the current implementation status. Simulation applications considered include the Transport Systems Research Vehicle, the Differential Maneuvering Simulator, the General Aviation Simulator, and the Visual Motion Simulator.

Cleveland, Jeff I., II↗
DOE OSTI2014

DIRAQ: scalable in situ data- and resource-aware indexing for optimized query performance

Scientific data analytics in high-performance computing environments has been evolving along with the advancement of computing capabilities. With the onset of exascale computing, the increasing gap between compute performance and I/O bandwidth has rendered the traditional post-simulation processing a tedious process. Despite the challenges due to increased data production, there exists an opportunity to benefit from "cheap" computing power to perform query-driven exploration and visualization during simulation time. To accelerate such analyses, applications traditionally augment, post-simulation, raw data with large indexes, which are then repeatedly utilized for data exploration. However, the generation of current state-of-the-art indexes involves a compute- and memory-intensive processing, thus rendering them inapplicable in an in situ context. In this paper we propose DIRAQ, a parallel in situ, in network data encoding and reorganization technique that enables the transformation of simulation output into a query-efficient form, with negligible runtime overhead to the simulation run. DIRAQ's effective core-local, precision-based encoding approach incorporates an embedded compressed index that is 3---6 $$\times $$ ? smaller than current state-of-the-art indexing schemes. Its data-aware index adjustmentation improves performance of group-level index layout creation by up to 35 % and reduces the size of the generated index by up to 27 %. Moreover, DIRAQ's in network index merging strategy enables the creation of aggregated indexes that speed up spatial-context query responses by up to $$10\times $$ 10 ? versus alternative techniques. DIRAQ's topology-, data-, and memory-aware aggregation strategy results in efficient I/O and yields overall end-to-end encoding and I/O time that is less than that required to write the raw data with MPI collective I/O.

Computer Science↗
DOE OSTI2026

Evaluating Supply Prioritization Strategies for Risk-Informed Decision Making in an Arbitrary Gas Network

Supply disruptions and infrastructure failures in natural gas networks present critical challenges to energy reliability and risk-informed planning. This study evaluates two supply prioritization strategies, Maximum Delivery Prioritization (MDP) and Demand-Based Prioritization (DBP), within an arbitrary natural gas network under conditions of supply shortage. Model performance under both strategies is assessed in response to node and edge failure using demand satisfaction metrics, system-wide and localized dependency scores, and geographic information system (GIS)-based spatial analysis. Results show that DBP better preserves supply for high-demand nodes, while MDP offers broader coverage. The underlying network topology plays a critical role in shaping prioritization outcomes. Integrated GIS visualization enhances the interpretability of vulnerability assessments, revealing structurally critical components and localized vulnerabilities. The proposed framework supports scalable, data-driven decision-making for infrastructure planners and engineers, enabling improved disruption recovery and efficiency in constrained natural gas networks. These insights contribute to the development of more robust energy systems capable of withstanding stress and disruptions.

Peterson, Steven [ORNL] (ORCID:0000000287672998)↗
DOE OSTI2018

Status of the Full Circumference Examination of the Inner Container Closure Weld Region for Selected 3013 DE Container

One of the main focus areas of the 3013 Surveillance Program is a thorough evaluation of the inner container closure weld region (ICCWR) opened for destructive examination (DE). As part of the protocol to investigate the corrosion in the ICCWR a laser confocal microscope (LCM) is used to perform close visual examination of the surface and measurements of corrosion features on the surface. In FY17, DE containers from FY13 through FY16 were evaluated to select candidates for a full circumference analysis of the ICCWR. In FY18, the selected DE containers for full circumference evaluation (FCE) were processed according to the ICCWR protocol. However, due to the time intensive task for collecting high magnification images for a full circumference, only FY15 DE07 was selected for completion of LCM data collection in FY18 with the remaining DE containers scheduled to be completed in FY19.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Evaluation of Commercially Available Precursors for Obscuring Wet Industrial Irradiator Facility Pools to Delay Adversarial Source Removal (Part 2)

The behavior of commercially available potential obscurants for cobalt-60 ( 60 Co) wet-source storage industrial irradiator facilities (IRFs) were further evaluated for corrosive behavior of Nordion C-188 pencil stubs and obscurant properties under radiation exposure ( 60 Co). The potential obscurants studied included: titania aqueous dispersions (TAD - water soluble white paint), Chlorazol Black (CBOD - Chlorazol Black organic dye), powdered milk (COW - calcium obscurant in water), diatomaceous earth (DEA - diatomaceous earth additive), and rhodamine 6G (R6G). For corrosion efforts, stubs from an inert C-188 pencil-source rod were soaked in obscurant solutions and visually inspected. For radiation stability, obscurant samples were exposed to 60 Co radiation sources at 207 rad/s. The results from these studies reveal: the obscurants had no impact on the surrogate samples and may assist in terms of corrosion resistance; materials that did not rely on organic compounds to provide obscurance performed the best, as the organic compounds decomposed too rapidly in the high radiation environment, whereas the materials survived.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗