Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “harden”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2026

A Novel Surface Restoration Method for Hydropower Steel Components: Plasma Gouging and Inconel Cold Spray Coating for Material Repair

A novel surface restoration approach combining plasma gouging with subsequent cold spray deposition is demonstrated in this study. Plasma gouging effectively removes the damaged steel surface, leaving grooves and forming a plasma gouging affected zone up to ~300?µm thick. Within this zone, a hardened martensitic layer with a peak hardness of ~370?HV—almost twice that of the base substrate (~200?HV)—is produced. Following plasma gouging, cold spray deposition is applied to rebuild the surface. Experimental results reveal that cold spray coatings deposited at low energy suffer from delamination, whereas high energy cold spray deposits yield a well-bonded coating. Microstructural analysis further shows that the martensitic layer formed by plasma gouging undergoes dynamic recrystallization during cold spray, reducing the hardness to 317?HV. These findings demonstrate the feasibility of this hybrid method for effective surface restoration of damaged steel components.

Wang, Tianhao↗
DOE OSTI2022

Evolution of carbide precipitates in Haynes® 282 superalloy processed by wire arc additive manufacturing

Precipitation hardening regulated with heat treatments is a critical technique for tuning the mechanical properties of Ni-based superalloys fabricated with additive manufacturing, where mechanical deformation is no longer viable for microstructural refinement. As one of the key precipitates, carbides prevail in the additively manufactured alloys, whose precipitation kinetics remain largely vague. This work studies the influence of heat treatments on the evolution of MC- and M 23 C 6 -type carbides within a Haynes® 282 superalloy prepared by wire arc additive manufacturing (WAAM). SEM-EDS analysis was performed to identify the evolution pathways of the carbides, and TEM and XRD characterizations were carried out to track the crystallographic features. The MC-type carbides are originally present in the as-printed alloy, which distribute uniformly across the whole material and remain largely unchanged in size during the heat treatments. By contrast, the incipiently non-existent M 23 C 6 -type carbides precipitate during an aging treatment at 1010 °C, which majorly extend along the grain boundaries as kinetically feasible sites. Further experimental and computational analysis confirms the enhancing effect of the M 23 C 6 -type carbides on the Vickers hardness. For the first time, this work revealed the evolution pathways of carbides within a Haynes® 282 superalloy prepared by WAAM, providing critical information for tunning the microstructure and mechanical properties. Finally, the carbide evolution kinetics established in this work can be potentially extended to other alloys prepared with WAAM, providing critical information to prevent mechanical failures associated with carbide coarsening.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Micro-mechanical investigation of the thermo-mechanical properties of micro-architectured tungsten coatings

The thermo-mechanical response of micro-architectured tungsten coatings is characterized in the temperature range of 293 to 673 K using both in situ micro-compression experiments inside a scanning electron microscope (SEM) as well as image-based crystal plasticity finite element method (CPFEM) simulations. The experiments were conducted on micropillar-like specimens that were focus ion beam milled into the coatings, while the simulations were conducted on columnar-grained micropillar simulation cells constructed based on the statistics of the coating’s microstructure. The experimental results show that the stress–strain response and deformation mode exhibit a strong temperature-dependence. At room temperature, catastrophic failure is observed shortly after yield and is manifested in the form of intergranular fracture and buckling of individual columnar grains. With increasing temperature, this catastrophic failure is gradually suppressed and the material exhibits a steadier strain hardening response at 693 K. The CPFEM simulations are also shown to be in good agreement with the experimental results, and these simulations indicate that the material response is strongly influenced by the local crystallographic anisotropy and microstructure inhomogeneity. Furthermore, the simulations capture the underlying mechanisms that control the temperature-dependent transition in deformation mode. The current results highlight that the micro-architectured microstructure offers a great combination of excellent mechanical strength and structural integrity at elevated temperatures, which is of importance for high temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Incorporating point defect generation due to jog formation into the vector density-based continuum dislocation dynamics approach

During plastic deformation of crystalline materials, point defects such as vacancies and interstitials are generated by jogs on moving dislocations. A detailed model for jog formation and transport during plastic deformation was developed within the vector density-based continuum dislocation dynamics framework. Here as a part of this model, point defect generation associated with jog transport was formulated in terms of the volume change due to the non-conservative motion of jogs. Balance equations for the vacancies and interstitials including their rate of generation due to jog transport were also formulated. A two-way coupling between point defects and dislocation dynamics was then completed by including the stress contributed by the eigen-strain of point defects. A jog drag stress was further introduced into the mobility law of dislocations to account for the energy dissipation during point defects generation. A number of test problems and a fully coupled simulation of dislocation dynamics and point defects generation and diffusion were performed. The results show that there is an asymmetry of vacancy and interstitial generation due to the different formation energies of the two types of defects. The results also show that a higher hardening rate and a higher dislocation density are obtained when the point defect generation mechanism is coupled to dislocation dynamics.

36 MATERIALS SCIENCE↗
DOE OSTI2022

A concurrent irradiation-mechanics multiscale coupling model

The vast majority of our current knowledge regarding the basic mechanisms controlling irradiation effect on mechanical properties is based almost entirely on the results of post-irradiation experiments or theoretical models. However, the concurrent effects of irradiation, mechanical stress, and thermal damage on the failure phenomena of materials and components remain largely unexplored due to its internal multiscale-multiphysics coupling nature. Here, we present here a concurrent irradiation-mechanics multiscale coupling model. The concurrent evolutions of nanoscale irradiation defect clusters, microscale dislocation configurations, and mechanical responses are well captured based on coupling cluster dynamics, discrete dislocation dynamics, and the finite element methods using an effective time marching scheme. Model predictions of defect densities and size are in general agreement with experimental observations. Irradiation hardening is shown to take place also in samples undergoing concurrent irradiation-mechanical loading, similar to samples tested post-irradiation. However, the occurrence of plastic flow localization and dislocation channel formation is not accompanied with apparent yield drop (softening) under concurrent irradiation-mechanical loading conditions, which is different from the post-irradiation case.

42 ENGINEERING↗
DOE OSTI2025

A phase-field fracture formulation for generalized standard materials: The interplay between thermomechanics and damage

Accurately modeling fracture of ductile materials poses open challenges in the field of computational mechanics due to the multiphysics nature of their failure processes. Integrating the interplay between thermodynamics and damage into ductile fracture models is vital for predicting critical failure modes. Here, in this paper, we develop a versatile phase-field (PF) framework for modeling ductile fracture, taking into account finite-strain elasto-plasticity. The framework stems from a variational formulation of constitutive relations for generalized standard materials (GSMs), whose response is described by a Helmholtz free energy and a dissipation pseudo-potential. Its variational structure is based on a minimum principle for a functional that expresses the sum of power densities for reversible and irreversible processes. By minimizing this functional with a constraint on a von Mises yield function, we derive the evolution equation for the equivalent plastic strain and an associative flow rule. This constrained optimization problem is analytically solved for a wide class of thermo-viscoplasticity models. The key innovations of the current work include (i) a cubic plastic degradation function that accounts for a non-vanishing damage-dependent yield stress, (ii) closed-form expressions of the Helmholtz free energy and dissipation pseudo-potential for three thermo-viscoplasticity models, (iii) an extended Johnson–Cook plasticity model with a nonlinear hardening law, and (iv) a plastic work heat source that depends on the plastic degradation function and a variable Taylor–Quinney (TQ) coefficient. The capabilities of the proposed framework are tested with the aid of four ductile fracture problems, including the Sandia Fracture Challenge. In each of these problems, we examine the evolution of relevant field variables such as the PF order parameter, the equivalent plastic strain, the temperature, and the internal power dissipation density, in addition to the overall structural response quantified by the force–displacement curve. These numerical studies demonstrate that the proposed framework effectively represents ductile fracture, yielding computational results that exhibit good agreement with experimental data.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Dynamic crushing of metal lattice metamaterials: Shock mode diagrams and transition to topology-independent compaction regime

Additively manufactured lattice metamaterials offer design versatility in strength and energy absorption and provide an additional degree of freedom through the selection of the lattice topology. Under quasistatic loading, the unit cell structure can strongly affect the stiffness, yield, and post-yield behavior, but whether and to what degree the effect of lattice topology persists into dynamic loading scenarios, up to the compaction shock regime, has not been established. LLNL’ s ALE3D hydrocode was used to perform a computational investigation of dynamic loading in multiple lattice types, including the gyroid, octet, Schwarz D, and rhombic dodecahedron, under impact velocities from 0.25 to 2.25 km/s. Shock Hugoniots for each lattice topology are generated and compared, suggesting that above a critical velocity, distinctions between architectures may not persevere and compacted lattices behave similarly. Here, to investigate the transition between topology-dependent quasistatic compression and the topology-independent regime above the critical velocity, a one-dimensional elastic-linear hardening plasticity-densified solid (E-LHP-DS) shock model for lattice materials was developed that relies upon confined compression to link the quasistatic and shock mechanics. Unlike similar works, the model does not assume rigid behavior prior to yield or locking behavior at densification, allowing a richer exploration of lattice mechanics. With only six parameters, the analytical model simultaneously fit quasistatic confined compression simulations for relative densities 0.1 $≤ \bar{ρ} ≤$ 0.9 and predicted dynamic compaction behavior to traverse several distinct shock modes, each defined by a critical impact speed (equivalently, critical stresses). Comparing the numerical results to the one-dimensional E-LHP-DS shock model predictions suggests that the topology-independence under strong shocks is linked to the onset of densification, which can be predicted based on quasistatic confined compression results.

Cellular material↗
DOE OSTI2022

Cantor-derived medium-entropy alloys: bridging the gap between traditional metallic and high-entropy alloys

The year 2004 marked the beginning of a new era in the design of metallic materials, as the concept of multiple principal component alloys, commonly known as High-Entropy Alloys (HEAs), was proposed by Cantor and Yeh. The unexpected single-phase microstructure, instead of the expected brittle intermetallic compounds, was attributed to the large entropy of mixing and immediately caught the attention of the scientific community. Today, HEAs are considered important advanced materials and a broad range of alloys using nominally the same design principle have been investigated. Despite that, the CrMnFeCoNi (Cantor) alloy stands out as the most successful HEA due to its outstanding mechanical properties and microstructure. In this scenario, variants of the Cantor alloy, named medium-entropy alloys (MEAs), are gaining significant interest as they display a better industrial potential than both HEAs and traditional alloys. These variants of the Cantor alloy with only three or four main elements result in 15 possible combinations. The microstructure of these alloys is discussed in terms of advanced characterization as well as thermodynamic parameters and computational simulation. Their phase stability is addressed over a wide range of temperatures and strain rates. The mechanical properties, especially the fracture toughness, of the CrFeCoNi and CrCoNi alloys have been reported to be even superior to those of the Cantor alloy and most modern engineering alloys. This is associated with the formation of a continuous sequence of strengthening mechanisms, including hierarchical twin networks, which serve to prolong the strain hardening. The present article reviews and critically assesses, for the first time, recent advances in these Cantor-derived MEAs.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Peak microhardness recovery via T6 heat treatment with extremely soft annealed Al7075 feedstock in additive friction stir deposition

With standard T6 heat treatments, precipitate-hardened alloys such as Al7075 and Al6061 fabricated using Additive Friction Stir Deposition (AFSD) method restore to noticeablely different peak mechanical properties. Previous research observed similar results but did not provide a viable solution. This study proposes a new processing strategy, namely enhanced plastic deformation by subjecting the Al7075 feedstock to annealed softening treatments. Specifically, by annealing the standard T651-Al7075 feedstock and deposition substrate (179 HV), their Microhardness were first degraded to its lowest state (80 HV), which is called a Soft-to-Soft system. For the Soft-to-Soft system subjected to AFSD, after undergoing appropriate T6 heat treatment, the microhardness of the AFSD 7075 alloy was restored to its peak value (183.1 ± 1.8 HV). The results indicate that this softening strategy can effectively reduce the non-strengthening phase in the AFSD matrix, thereby increasing the strengthening phase (η′ phase). This addresses the issue of traditional AFSD-prepared aluminum alloys being unable to achieve peak performance through T6 heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Strength-ductility synergy through microstructural and compositional heterogeneity in directed energy deposition additive manufacturing of face-centered cubic materials

Directed energy deposition (DED) is an additive manufacturing (AM) process based on welding technology and offers the advantages of large build volume, high deposition rate, and ability to fabricate multi-material parts. Epitaxial continuous columnar grain growth is a characteristic microstructural feature of DED processed alloys. In this study, a bamboo-like microstructure (periodic alternation of equiaxed and columnar structure) was produced by adopting an intermittent deposition strategy in 316L stainless steel and Inconel 625. The formation of a bamboo-like alternating microstructure was confirmed through electron backscattered diffraction (EBSD) analysis. Hardness mapping showed that the columnar to equiaxed transition (CET) occurred at the region right below the fusion line. A finite element (FE) model was used to investigate the relationship between the temperature gradient (G) and the solidification rate (R). The FE model showed a low G/R ratio at the region right below the interface promoting the CET. The grain size and material-dependent deformation behaviors are analyzed using digital image correlation (DIC). The lower deformation on the fine-grain regions observed in DIC analysis is attributed to a higher strain hardening rate, which is confirmed through dislocation density analysis on a tensile-interrupted specimen. The periodically alternating grain size coupled with the microstructural changes caused by intermittent deposition strategy result in a better strength-ductility synergy in both single-material and bimetallic specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Enhancing fatigue life of aluminum alloy castings through cavitation water jet peening: Experiments and simulations

This study presents an investigation into the enhancement of the fatigue life of aluminum castings through the application of cavitation water-jet peening (CWJP). CWJP harnesses the impacts of water cavitation to induce surface compressive residual stress within metallic materials. In this work, CWJP was applied to a high pressure die-cast (HPDC) Al–Si alloy A380 with three different water-jet traverse velocities. The fatigue-life improvement, evaluated in a 4-point bending configuration (stress ratio R = 0.1), was found to vary with applied stress level and ranges from 1.6 to 10 times that of the parent alloy. The data also shows that decreasing the traverse velocity results in greater compressive residual stresses within the surface layer and a concurrent increase in surface roughness. This residual stress layer extends to a depth of 400 μm below the surface, as confirmed by through-thickness residual stress and microhardness measurements. CWJP treatment effectively slows down fatigue crack propagation, as evidenced by microstructural observations of narrower striation spacing. Simulations reveal that compressive residual stresses, in addition to surface hardening during CWJP, are key to improving fatigue life. A 20% increase in surface hardness and 150 MPa compressive residual stress imposed by CWJP process provides an average 5-fold enhancement of fatigue life across different stress levels. This study demonstrates the potential of CWJP as an effective surface treatment to enhance the fatigue life of aluminum castings, such as HPDC components for automotive applications.

Al casting↗
DOE OSTI2021

A constitutive model incorporating grain refinement strengthening on metallic alloys

Surface nano-crystallization techniques have been recently developed as one of the most efficient ways to optimize materials’ structure, and therefore develop the local and global mechanical behavior as to increase strength without compromising ductility. Here, in this work, we present a constitutive model incorporating grain refinement hardening to simulate the nano-crystallization technique, specifically, surface mechanical attrition treatment. The computation is implemented using user-defined VUMAT subroutines. As an example of its application, a geometry model with full coverage of random impacts are employed. The results show that the model has rather precise predictability of grain size evolution during plastic deformation. The readily embedded with a computational code of material dynamics enables this novel model to be a promising tool to study the dynamic evolution of microstructures under plastic deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Irradiation effects on Al 0.3 CoCrFeNi and CoCrMnFeNi high-entropy alloys, and 316H stainless steel at 500 °C

To evaluate the potential of high entropy alloys (HEAs) for nuclear applications, two HEAs, Al 0.3 CoCrFeNi and CoCrFeMnNi, and a conventional Type 316H stainless steel (SS) were irradiated with 1 MeV krypton ions at 500 degrees C up to 1 dpa, and examined in-situ with a transmission electron microscope (TEM). After irradiation, a high density of ordered L1 2 nanoparticles was observed in Al 0.3 CoCrFeNi. In contrast, no phase transformation was observed in CoCrFeMnNi and 316H SS. In the thin foil regions of TEM samples, stacking-fault tetrahedra were observed in the HEAs. In the thick foil regions, interstitial dislocation loops were observed for all alloys, and the areal loop density increased linearly with foil thickness. The Al 0.3 CoCrFeNi had the largest loop size (the lowest density), followed by the CoCrFeMnNi and then the 316H SS. The higher loop nucleation rate in the 316H SS was attributed to carbon content. Finally, the degree of irradiation hardening was slightly lower for the HEAs than for the 316H SS, which is a promising sign for the nuclear application of HEAs at high temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Characterization of mechanical properties and deformation behavior of highly irradiated 316L stainless steel from target modules at the Spallation Neutron Source using digital image correlation analysis

Tensile specimens with irradiation doses ranging from approximately 0.7 to 7.6 displacements per atom (dpa) were fabricated from 316L samples removed from Spallation Neutron Source (SNS) target vessels after service. Tensile tests were performed in conjunction with digital image correlation (DIC) characterization, which permitted detailed analysis of the strain distribution and deformation behavior of the specimen gauge sections during testing. The results show, while considerable hardening (500–700 MPa increase in yield strength) occurred in the 316L SNS target material with increasing dose, appreciable ductility (19–23% total elongation) remained in the material after irradiation to 7.6 dpa in the mixed neutron/proton environment of the SNS target region. The DIC data showed the strain distribution and deformation behavior of all irradiated specimens were nonuniform during testing. Strain localization in the form of deformation bands or “hotspots” was observed during testing, and in some specimens, the bands propagated as deformation waves along the gauge section. The “traveling wave” deformation behavior affected the amount of elongation each specimen achieved, and the scatter in the elongation data was attributed to the large variation in deformation behavior observed among different specimens. Bands of localized strain, or deformation bands, oriented at specific angles were observed in two-dimensional plots of the strain distribution in the gauge sections of some specimens. Overall, this paper describes the experimental procedures, results, and deformation behavior of tensile specimens from SNS targets after service and illustrates the value of DIC characterization during tensile testing of irradiated materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In situ high-energy X-ray study of deformation mechanisms in additively manufactured 316L stainless steel

A key structural material planned to be used in the core of the Transformational Challenge Reactor is the additively manufactured 316L stainless steel (AM 316L SS). While the deformation of conventionally-manufactured 316 SS have been extensively studied, the deformation mechanism of AM 316L SS is less known. Here the room-temperature tensile behavior of AM 316L SS was studied in situ using high-energy X-ray diffraction and X-ray tomography. Diffraction yielded the lattice strains and the dislocation densi-ties of the AM 316L SS, which were compared to those of a conventionally processed 316H SS. It was found that while the conventional 316H SS had three distinct deformation stages, namely stage II ather-mal hardening, stage III dynamic recovery, and stage IV, the AM 316L experienced only the stages III and IV after an initial transitional period. The plastic instability stresses (PIS), i.e. the true ultimate tensile strength, were nearly the same in both materials. The AM 316L had very low dislocation barrier strength throughout the plastic deformation, which, in combination with the invariant PIS, explained its high dis-location storage capability and the attractive combination of strength and ductility. Tomography revealed morphological changes of the built-in pores in the AM 316L during deformation and fracture, and it was concluded that large pores close to the surface might have significant roles in the necking stage.

316 stainless steel↗
DOE OSTI2021

Influence of neutron irradiation on Al-6061 alloy produced via ultrasonic additive manufacturing

Samples of aluminum alloy 6061 produced via ultrasonic additive manufacturing (UAM) were irradiated in the High Flux Isotope Reactor (HFIR) up to 17.3 dpa at ~70°C while in contact with water using perforated rabbit capsules. The irradiation campaign included as-received (AR) material, specimens subjected to various post-weld heat treatments (PWHTs, including hot isostatic pressing [HIP]), and reference (wrought) alloy samples. Mechanical tensile tests, accompanied by digital image correlation (DIC) analysis, fractography, and metallography, were performed as a part of the post-irradiation evaluation. The X- and Y-specimens (i.e., oriented in the sonotrode moving and vibration directions, respectively) showed pronounced radiation hardening and ductility decrease. Specific serration flow behavior and propagation of deformation bands were observed under various material conditions up to 3.5 dpa but disappeared at 17.3 dpa. In all cases, the fracture mechanism of X- and Y-specimens was ductile; ductile dimples dominated the fracture surface. Irradiated X- and Y-specimens showed good performance, regardless of material conditions (AR or PWHT). The performance of Z-specimens oriented in the build direction was strongly dependent on the PWHT. The AR and aged specimens showed fracture stress decrease with dose, and they experienced fracture under irradiation after 3.5 dpa; specimen cross section analysis revealed specific interface degradation that was likely related to corrosion. Recrystallization significantly improved in-reactor performance. Finally, HIP suppressed interface degradation due to recrystallization and pore removal, which led to good in-reactor performance for Z-specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A microscopic and crystallographic study of proton irradiated alloy 718

Solution annealing and age hardening are important processes for achieving good engineering and chemical properties of alloy 718. The composition of alloy 718 also plays an important role as it can affect both mechanical (γ”- and γ’-phase formation) and irradiation behaviors. Therefore, in this study five different sets of alloy 718 samples with two different chemical compositions were fabricated using different processing conditions and irradiated up to 4 dpa. Based on the effects of irradiation on the microstructural data of γ”- and γ’-phases, irradiation-induced dislocation statistics, and crystallographic data, it can be inferred that the samples processed at high solution annealing temperature (1093°C) behave better under irradiation compared to the samples processed at low solution annealing temperatures (945 and 1065°C).

36 MATERIALS SCIENCE↗