Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “graphitization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Accelerated viscoelastic characterization of T300-5208 graphite-epoxy laminates

A viscoelastic response scheme for the accelerated characterization of polymer-based composite laminates in applied to T300/5208 graphite/epoxy. The response of uni-directional specimens is modeled. The transient component of the viscoelastic creep compliance is assumed to follow a power law approximation. A recursive relationship is developed, based upon the Schapery single-integral equation, which allows approximation of a continuous time-varying uniaxial load using discrete steps in stress. The viscoelastic response of T300/5208 to transverse normal and shear stresses is determined unsing 90 deg and 10 deg off-axis tensile specimens. In each case the seven viscoelastic material parameters required in the analysis are determined experimentally using short-term creep and creep recovery tests. It is shown that an accurate measure of the power law exponent is crucial for accurate long-term prediction. A short term test cycle selection procedure is proposed, which should provide useful guidelines for the evaluation of other viscoelastic materials.

Tuttle, M. E.↗
NASA NTRS1985

Thermal expansion of selected graphite reinforced polyimide-, epoxy-, and glass-matrix composite

The thermal expansion of three epoxy-matrix composites, a polyimide-matrix composite and a borosilicate glass-matrix composite, each reinforced with continuous carbon fibers, has been measured and compared. The expansion of a composite with a rubber toughened epoxy-matrix and P75S carbon fibers was very different from the expansion of two different single phase epoxy-matrix composites with P75S fibers although all three had the same stacking sequence. Reasonable agreement was obtained between measured thermal-expansion data and results from classical laminate theory. The thermal expansion of a material may change markedly as a result of thermal cycling. Microdamage, induced by 250 cycles between -156 C and 121 C in the graphite/polyimide laminate, caused a 53 percent decrease in the coefficient of thermal expansion. The thermal expansion of the graphite/glass laminate was not changed by 100 thermal cycles from -129 C to 38 C; however, a residual strain of about 10 x 10 to the minus 6 power was measured for the laminate tested.

Tompkins, S. S.↗
NASA NTRS1985

Measurement of damping of graphite epoxy materials

Work on a damping measurement test apparatus is discussed. The device is designed to excite tube specimens in a vacuum chamber. Also some experiments were conducted on a tube specimen to confirm previously reported results. A table of data showing the results of forced vibration tests using a half ring and a free-free boundary is given. The main purpose was to study the effect of the frequency resolution on the damping ratio measurements.

Crocker, M. J.↗
NASA NTRS1984

Coefficient of restitution for low velocity transverse impact of thin graphite-epoxy laminates

A simple model is presented for the low velocity impact behavior of thin plates composed of T300/5208 graphite/epoxy. The model, which is constructed on the assumption that the plate is inextensible in the fiber direction and that the material is incompressible in the z direction, is able to predict the energy absorbed by the target during an impact event, or the 'coefficient of restitution'. The plate essentially deforms by shear, allowing the model to neglect bending deformations. The coefficient of restitution is predicted to increase with large interlaminar shear strength and low transverse shear modulus of the laminate. The coefficient's experimentally measured values agree with model-predicted values within a reasonable error.

Lal, K. M.↗
NASA NTRS1985

A nonlinear analysis of infinitely long graphite-epoxy cylindrical panels loaded with internal pressure

The structural response of internally pressurized composite cylindrical panels, representative of a transport aircraft's fuselage skins, is predicted by means of a one-dimensional, geometrically nonlinear analysis. An analytical study is conducted for the response of 4-, 8-, and 16-ply graphite/epoxy skins. The results obtained indicate that the response is geometrically nonlinear, and that a boundary layer with a severe bending gradient exists at the panel edges. The importance of through-the-thickness shearing deformations in the bending boundary layer is illustrated through comparison of analyses based on Kirchhoff-Love and shear deformation theories. Numerical results for the bending boundary layer lengths of the different panels are presented, and two bending boundary layers are predicted with the shear deformation theory.

Boitnott, R. L.↗
NASA NTRS1985

Postbuckling of flat unstiffened graphite-epoxy plates loaded in shear

An experimental and analytical study was conducted of the postbuckling response and failure characteristics of 8-, 16-, and 24-ply unstiffened graphite/epoxy plates under shear loading, including orthotropic, quasi-orthotropic, entirely +, -45 deg ply, and (0/90)s-class plates. Postbuckling stiffness is noted to be influenced by the stacking sequence and by the inplane boundary condition imposed on the test section by a picture frame test fixture. The ratio of failure load to buckling load was higher for specimens that had higher width-to-thickness ratios. It is noted that high displacement gradients may induce transverse shear stresses, and that delamination was the failure mechanism for many of the 8-ply specimens. An adhesive failure between the composite specimen and metal edge reinforcements initiated failure of the 16- and 24-ply specimens.

Rouse, M.↗
NASA NTRS1985

Graphite formation in cast iron, phase 2

Several types of cast irons are directionally solidified aboard the KC-135 aircraft. Also, control samples are run on Earth for comparison. Some of these samples are unusable because of various mechanical problems; the analysis and the interpretation of results on the samples that are run successfully is discussed.

Stefanescu, D. M.↗
NASA NTRS1986

Graphite fiber intercalation: Basic properties of copper chloride intercalated fibers

In situ resistance measurements were used to follow the intercalation of copper chloride in pitch-based fibers. Subsequent single fiber resistivity measurements reveal a large range of resistivities, from 13 to 160 micro-ohms cm. Additional density measurements reveal a bimodal distribution of mass densities. The dense fibers have lower resistivities and correspond to the stage III compound identified by X-ray diffraction. Neither resistivity nor density correlate with diameter. Both energy dispersive spectroscopy and mass density data suggest that excess chlorine resides in the intercalated fiber, resulting in a stoichiometry of C4.9n CuCl2.5 (where n is the stage number) for the denser fibers. Finally, thermogravimetric analysis shows a 33 percent loss in mass upon heating to 700C. This loss in mass is attributed to loss of both chlorine and carbon.

Jaworske, D. A.↗
NASA NTRS1986

A comparison of the bromination dynamics of pitch-based and vapor-grown graphite fibers

The electrical resistance of pitch based P-100 fibers and experimental organic vapor grown fibers was recorded in-situ during bromination and subsequent exposure to ambient laboratory air. The results indicate that the bromination and debromination reactions proceed much slower for vapor grown fibers than for pitch based. While this may be due in part to the larger diameter of the vapor grown fibers, the majority of the effect can probably be attributed to the differences in graphene plane orientation between the fiber types. Although the reactions are slower in the vapor grown than in the pitch based fibers, the extent of reaction as measured by the change in electrical resistance is essentially the same, with comparable (or larger) decreases in resistivity. The bromination reaction proceeds with one or more plateaus in the resistance versus time curves, which suggests staging and strengthens the argument that these fibers produce true intercalation compounds.

Gaier, J. R.↗
NASA NTRS1986

Light weight fire resistant graphite composites

Composite structures with a honeycomb core and characterized by lightweight and excellent fire resistance are provided. These sandwich structures employ facesheets made up of bismaleimide-vinyl styrylpyridine copolymers with fiber reinforcement such as carbon fiber reinforcement. In preferred embodiments the facesheets are over layered with a decorative film. The properties of these composites make them attractive materials of construction aircraft and spacecraft.

Kourtides, D. A.↗
NASA NTRS1984

Standard test evaluation of graphite fiber/resin matrix composite materials for improved toughness

Programs sponsored by NASA with the commercial transport manufacturers to develop a technology data base are required to design and build composite wing and fuselage structures. To realize the full potential of composite structures in these strength critical designs, material systems having improved ductility and interlaminar toughness are being sought. To promote systematic evaluation of new materials, NASA and the commercial transport manufacturers have selected and standardized a set of five common tests. These tests evaluate open hole tension and compression performance, compression performance after impact at an energy level of 20 ft-lb, and resistance to delamination. Ten toughened resin matrix/graphite fiber composites were evaluated using this series of tests, and their performance is compared with a widely used composite system.

Chapman, Andrew J.↗
NASA NTRS1986

Anticorrelation of Shubnikov-deHaas amplitudes and negative magnetoresistance magnitudes in intercalated pitch based graphite fibers

In pitch based carbon fibers at low temperatures, simultaneous presence of a negative magnetoresistance and the Shubnikov-deHaas effect are found. The strengths of these effects correlate inversely. These results can be understood in terms of the amount of order vs disorder in the fiber, as described by Guigon and Oberlin from structural studies.

Woollam, John A.↗