Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “flow efficiency”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53

Overall and blade element performance of a 1.20-pressure-ratio fan stage with rotor blades reset -5 deg

A 51-cm-diam model of a fan stage for a short haul aircraft was tested in a single stage-compressor research facility. The rotor blades were set 5 deg toward the axial direction (opened) from design setting angle. Surveys of the air flow conditions ahead of the rotor, between the rotor and stator, and behind the stator were made over the stable operating range of the stage. At the design speed of 213.3 m/sec and a weight flow of 31.5 kg/sec, the stage pressure ratio and efficiency were 1.195 and 0.88, respectively. The design speed rotor peak efficiency of 0.91 occurred at the same flow rate.

Lewis, G. W., Jr.↗

Low dose dynamic CT myocardial perfusion imaging using a statistical iterative reconstruction method

Purpose: Dynamic CT myocardial perfusion imaging has the potential to provide both functional and anatomical information regarding coronary artery stenosis. However, radiation dose can be potentially high due to repeated scanning of the same region. The purpose of this study is to investigate the use of statistical iterative reconstruction to improve parametric maps of myocardial perfusion derived from a low tube current dynamic CT acquisition. Methods: Four pigs underwent high (500 mA) and low (25 mA) dose dynamic CT myocardial perfusion scans with and without coronary occlusion. To delineate the affected myocardial territory, an N-13 ammonia PET perfusion scan was performed for each animal in each occlusion state. Filtered backprojection (FBP) reconstruction was first applied to all CT data sets. Then, a statistical iterative reconstruction (SIR) method was applied to data sets acquired at low dose. Image voxel noise was matched between the low dose SIR and high dose FBP reconstructions. CT perfusion maps were compared among the low dose FBP, low dose SIR and high dose FBP reconstructions. Numerical simulations of a dynamic CT scan at high and low dose (20:1 ratio) were performed to quantitatively evaluate SIR and FBP performance in terms of flow map accuracy, precision, dose efficiency, and spatial resolution. Results: Forin vivo studies, the 500 mA FBP maps gave −88.4%, −96.0%, −76.7%, and −65.8% flow change in the occluded anterior region compared to the open-coronary scans (four animals). The percent changes in the 25 mA SIR maps were in good agreement, measuring −94.7%, −81.6%, −84.0%, and −72.2%. The 25 mA FBP maps gave unreliable flow measurements due to streaks caused by photon starvation (percent changes of +137.4%, +71.0%, −11.8%, and −3.5%). Agreement between 25 mA SIR and 500 mA FBP global flow was −9.7%, 8.8%, −3.1%, and 26.4%. The average variability of flow measurements in a nonoccluded region was 16.3%, 24.1%, and 937.9% for the 500 mA FBP, 25 mA SIR, and 25 mA FBP, respectively. In numerical simulations, SIR mitigated streak artifacts in the low dose data and yielded flow maps with mean error <7% and standard deviation <9% of mean, for 30×30 pixel ROIs (12.9 × 12.9 mm{sup 2}). In comparison, low dose FBP flow errors were −38% to +258%, and standard deviation was 6%–93%. Additionally, low dose SIR achieved 4.6 times improvement in flow map CNR{sup 2} per unit input dose compared to low dose FBP. Conclusions: SIR reconstruction can reduce image noise and mitigate streaking artifacts caused by photon starvation in dynamic CT myocardial perfusion data sets acquired at low dose (low tube current), and improve perfusion map quality in comparison to FBP reconstruction at the same dose.

60 APPLIED LIFE SCIENCES↗

A fast Euler solver for steady flows

A numerical technique to solve the Euler equations for steady, two-dimensional flows is presented. The technique extends to two-dimensional problems a formulation which was found to be extremely efficient for one-dimensional flows. Generalized Riemann variables are defined along two families of orthogonal coordinates, and integrated separately, sweeping back and forth alternatively along coordinate lines. The technique is second-order accurate and converges very rapidly. In addition, each step requires a minimal number of operations. Preliminary results for subsonic and transonic shockless flows are presented and discussed.

Moretti, G.↗

Liquid–Liquid Microfluidic Flows for Ultrafast 5-Hydroxymethyl Furfural Extraction

We study the effects of liquid–liquid flow patterns on the extraction of 5-hydroxymethyl furfural from the aqueous phase into an organic phase (methyl isobutyl ketone, ethyl acetate, and 2-pentanol) at ultrashort residence times of 0.2–20 s in a coiled capillary microchannel. Slug, droplet, slug-droplet, dispersed, parallel, annular, and irregular two-phase flow patterns are generated. We evaluate the extraction efficiency and the volumetric mass transfer coefficient via experiments and computational fluid dynamics (CFD). The CFD predictions are in quantitative agreement with the experimental data. The convective and diffusive contributions to the mass transfer of different flow patterns are analyzed. For all solvent pairs, the extraction efficiency varies irregularly with increasing flow rate due to changes in the mass transfer mechanism caused by a transition between flow regimes. Overall, we demonstrate >90% extraction efficiencies with high volumetric mass transfer coefficients ranging from 0.006 to 2.17 s–1. Furthermore, a merit index is defined to assess the trade-off between the fast mass transfer and the pressure drop in biphasic microchannels. In general, the mass transfer rate increases significantly at high flow rates at the expense of a high-pressure drop. Furthermore, the ethyl acetate/water irregular flow pattern is optimal due to a large throughput, extraction efficiency, and mass transfer coefficient, with a minimal pressure drop.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Cyclic Versus Linear Isomers Produced by Reaction of the Methylidyne Radical (CH) with Small Unsaturated Hydrocarbons

The reactions of the methylidyne radical (CH) with ethylene, acetylene, allene, and methylacetylene are studied at room temperature using tunable vacuum ultraviolet (VUV) photoionization and time-resolved mass spectrometry. The CH radicals are prepared by 248 nm multiphoton photolysis of CHBr3 at 298 K and react with the selected hydrocarbon in a helium gas flow. Analysis of photoionization efficiency versus VUV photon wavelength permits isomer-specific detection of the reaction products and allows estimation of the reaction product branching ratios. The reactions proceed by either CH insertion or addition followed by H atom elimination from the intermediate adduct. In the CH + C2H4 reaction the C3H5 intermediate decays by H atom loss to yield 70(+-8)percent allene, 30(+-8)percent methylacetylene and less than 10percent cyclopropene, in agreement with previous RRKM results. In the CH + acetylene reaction, detection of mainly the cyclic C3H2 isomer is contrary to a previous RRKM calculation that predicted linear triplet propargylene to be 90percent of the total H-atom co-products. High-level CBS-APNO quantum calculations and RRKM calculation for the CH + C2H2 reaction presented in this manuscript predict a higher contribution of the cyclic C3H2 (27.0percent) versus triplet propargylene (63.5percent) than these earlier predictions. Extensive calculations on the C3H3 and C3H2D system combined with experimental isotope ratios for the CD + C2H2 reaction indicate that H-atom assisted isomerization in the present experiments is responsible for the discrepancy between the RRKM calculations and the experimental results. Cyclic isomers are also found to represent 30(+-6)percent of the detected products in the case of CH + methylacetylene, together with 33(+-6)percent 1,2,3-butatriene and 37(+-6)percent vinylacetylene. The CH + allene reaction gives 23(+-5)percent 1,2,3-butatriene and 77(+-5)percent vinylacetylene, whereas cyclic isomers are produced below the detection limit in this reaction. The reaction exit channels deduced by comparing the product distributions for the aforementioned reactions are discussed in detail.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Modeling of thermal processes in high pressure liquid chromatography II. Thermal heterogeneity at very high pressures

Advanced instruments for liquid chromatography enables the operation of columns packed with sub-2 {micro}m particles at the very high inlet pressures, up to 1000 bar, that are necessary to achieve the high column efficiency and the short analysis times that can be provided by the use of these columns. However, operating rather short columns at high mobile phase velocities, under high pressure gradients causes the production of a large amount of heat due to the viscous friction of the eluent percolating through the column bed. The evacuation of this heat causes the formation of significant axial and radial temperature gradients. Due to these thermal gradients, the retention factors of analytes and the mobile phase velocity are no longer constant throughout the column. The consequence of this heat production is a loss of column efficiency. We previously developed a model combining the heat and mass balance of the column, the equations of flow through porous media, and a linear isotherm model of the analyte. This model was solved and validated for conventional columns operated under moderate pressures. We report here on the results obtained when this model is applied to columns packed with very fine particles, operated under very high pressures. These results prove that our model accounts well for all the experimental results. The same column that elutes symmetrical, nearly Gaussian peaks at low flow rates, under relatively low pressure drops, provides strongly deformed, unsymmetrical peaks when operated at high flow rates, under high pressures, and under different thermal environments. The loss in column efficiency is particularly important when the column wall is kept at constant temperature, by immersing the column in a water bath.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis and Optimization of the Recompression Cycle with High Temperature Recuperator Bypass for Concentrating Solar Power Applications

This work analyzes the sCO2 recompression with high temperature recuperator (HTR) bypass power cycle for use in concentrating solar power (CSP) systems. CSP operation differs from other thermal power plants in that CSP must balance between maximizing the heat transfer fluid (HTF) temperature difference and maximizing the cycle thermal efficiency, which typically are inversely related. Large HTF temperature differences reduce the size and cost of thermal energy storage (TES), improve the solar receiver efficiency, and require lower mass flow rates that reduce pumping power required to elevate the HTF to the receiver. The recompression cycle with HTR bypass potentially offers improved thermal efficiency with larger HTF temperature differences as compared to the recompression cycle, and it has fewer turbomachinery components than the partial cooling cycle. The recompression with HTR bypass cycle adds a second lower temperature primary heat exchanger which transfers heat from the HTF to the fraction of sCO2 flow that bypasses the HTR. We developed a model to compare the recompression with HTR bypass cycle to the recompression and partial cooling cycles. A sweep of design parameters including bypass fraction, recompression fraction, recuperator conductance, and pressure ratio is used to form a pareto-optimal front with the cycle thermal efficiency and HTF temperature difference as objectives. An optimization routine has also been developed to find optimal design point parameters for a target HTF temperature difference. The performance of the recompression with HTR bypass cycle is compared with recompression and partial cooling cycles.

concentrating solar power↗

Translation-vibration-dissociation coupling in nonequilibrium hypersonic flows

A new simple and computationally efficient model was developed, describing the evolution of vibrational states during relaxation and dissociation. The model is based on dividing the nitrogen molecules into two types, those in the vibrational states at a lower level, whose vibrational energy is below a cutoff energy, and those in an upper level, with vibrational energy above the cutoff. Dissociation occurs at the upper level, and recombination returns molecules to the lower level. The model was applied to two flows of engineering interest, the flow through a normal Mach 15 shock wave at 60 km, and a supersonic quasi-one-dimensional flow in a nozzle. Results are compared to those obtained by existing translation-vibration-dissociation coupling models, with results indicating significant differences between the models.

Candler, Graham↗

Thermal performance simulation of a solar cavity receiver under windy conditions

Solar cavity receiver plays a dominant role in the light-heat conversion. Its performance can directly affect the efficiency of the whole power generation system. A combined calculation method for evaluating the thermal performance of the solar cavity receiver is raised in this paper. This method couples the Monte-Carlo method, the correlations of the flow boiling heat transfer, and the calculation of air flow field. And this method can ultimately figure out the surface heat flux inside the cavity, the wall temperature of the boiling tubes, and the heat loss of the solar receiver with an iterative solution. With this method, the thermal performance of a solar cavity receiver, a saturated steam receiver, is simulated under different wind environments. The highest wall temperature of the boiling tubes is about 150 C higher than the water saturation temperature. And it appears in the upper middle parts of the absorbing panels. Changing the wind angle or velocity can obviously affect the air velocity inside the receiver. The air velocity reaches the maximum value when the wind comes from the side of the receiver (flow angle {alpha} = 90 ). The heat loss of the solar cavity receiver also reaches a maximum for the side-on wind. (author)

14 SOLAR ENERGY↗

Experimental study of the influence of collector height on the steady state performance of a passive solar air heater

Passive solar air heaters, such as solar chimneys and Trombe Walls, rely on solar-induced buoyancy-driven (natural) convection to produce the flow of air. Although buoyancy-driven convection is well understood for a single vertical plate, buoyancy-driven convection in an asymmetrically-heated channel is more problematic, and in particular, the effects of the channel height on the flow rate and heat transfer. This paper reports on experiments on test rigs resembling lightweight passive solar air-heating collectors. The test rigs were of heights 0.5, 1.0 and 2.0 m, with adjustable channel depths (20-150 mm) and heat inputs (up to 1000 W/m{sup 2}). Measurements were made of the air, plate and cover temperatures, and air velocities. Results are presented as dimensionless correlations of mass flow (as Reynolds number) and efficiency against heat input (as Rayleigh number), channel depth and height. Thermal efficiency is shown to be a function of the heat input and the system height, but not of the channel depth; mass flow is shown to be a dependent on all three parameters. (author)

14 SOLAR ENERGY↗

Elucidating Instabilities Contributing to Capacity Fade in Bipyridine‐Based Materials for Non‐aqueous Flow Batteries

Abstract Metal‐based non‐aqueous redox flow batteries have the potential for long‐term energy storage if stability requirements can be achieved. One such stability issue in metal coordination complexes arises from ligand shedding in the anolyte upon reduction. Recognizing that the free ligands are relatively more stable than the metal coordination complex under highly reducing conditions, we evaluated a family of metal‐free bipyridinium materials as flow battery anolytes with the corresponding iron coordination complex as the catholyte. Bipyridinium compounds were functionalized for increased electrochemical stability, cycled in flow cells to understand efficiencies, and analyzed for degradation products. Methylation of the bipyridine nitrogens increased electrochemical stability yet left the reduced molecule susceptible to radical‐induced bond cleavage. Subsequent functionalization of bipyridine with carbomethoxy groups resulted in good battery performance with 96 % Coulombic and 90 % voltage efficiency, and improved cycling stability over a methoxy‐substituted anolyte with 14 % vs 36 % capacity fade in the first charge‐discharge cycle.

Kolesnichenko, Claudina X.↗

Robust system size reduction of discrete fracture networks: a multi-fidelity method that preserves transport characteristics

In this paper, we propose a multi-fidelity system reduction technique that uses weighted graphs paired with three-dimensional discrete fracture network (DFN) modelling for efficient simulation of subsurface flow and transport in fractured media. DFN models are used to simulate flow and transport in subsurface fractured rock with low-permeability. One method to alleviate the heavy computational overhead associated with these simulations is to reduce the size of the DFN using a graph representation of it to identify the primary flow sub-network and only simulate flow and transport thereon. The first of these methods used unweighted graphs constructed solely on DFN topology and could be used for accurate predictions of first-passage times. However, these techniques perform poorly when predicting later stages of the mass breakthrough. We utilize a weighted-graph representation of the DFN where edge weights are based on hydrological parameters in the DFN that allows us to exploit the kinematic quantities derivable a posteriori from the flow solution obtained on the graph representation of the DFN to perform system reduction and predict the later stages of the breakthrough curve with high fidelity. We also propose and demonstrate the use of an adaptive pruning algorithm with error control that produces a pruned DFN sub-network whose predicted mass breakthrough agrees with the original DFN within a user-specified tolerance. Lastly, the method allows for the level of accuracy to be a user-controlled parameter.

58 GEOSCIENCES↗

System efficiency and power assessment of the all-aqueous copper thermally regenerative ammonia battery

Thermally regenerative ammonia batteries (TRABs) use low-temperature (T < 100 °C) heat to provide stationary energy and power with higher power densities and efficiency relative to other waste heat devices. TRABs are an active area of research in waste heat devices, but currently there is little consensus on what aspect of the system is limiting TRAB performance and what maximum efficiencies are possible. Experiments and numerical models were used here to examine the sensitivity of the battery and distillation column in a TRAB system to key operating variables, thereby establishing practical limits and identifying focus areas for improving performance. Battery power was eight times more sensitive to ohmic losses than kinetic and mass transfer losses, regardless of the operating temperature, and the peak power density was simulated to be 18.8 mW cm –2 at 75 °C. Theoretical energy efficiency limits were defined for a series of ammonia concentrations and operating pressures, ranging from 5 – 12%, which is 2–3 times higher than previous experimental estimations. Atmospheric pressure column operation used a larger amount of waste heat compared to sub-atmospheric pressure. It is estimated that the volume of the battery would take up 9.2m 3 for every 1% of the power output of a natural gas turbine, but with realistic improvements to cell conductivity, the size would reduce to 2.5 m 3 . Finally, the results presented in this work will help streamline future development by focusing on minimizing ohmic losses and provide specific data for full system evaluation of future TRABs.

25 ENERGY STORAGE↗

Tritium aspects of the fusion nuclear science facility

The Fusion Nuclear Science Facility (FNSF) is intended to bridge the technical gaps from ITER to DEMO, and provide a fully nuclear environment for the advancement of materials and blanket science, among other missions. Though smaller (~500 MW fusion power) than the envisioned DEMO, our FNSF design still seeks to test DEMO-relevant components and technologies, and to that end one of its goals is to achieve a tritium breeding ratio near one using a dual-cooled lead lithium (DCLL) blanket. We explore here the migration of bred tritium through in-vessel components and coolant loops, which is exacerbated by the relatively low solubility of tritium in PbLi and the high operating temperatures envisioned in later phases of operation. Some features inherent to the design of the DCLL help limit tritium losses, namely the relatively high PbLi flow rates; coupled with efficient tritium extraction, the DCLL potentially achieves low tritium permeation losses without the use of permeation barriers. We outline here the design of such an extraction system, and some of the materials challenges that must be met in order to realize it. The efficacy of these and other design features, such as coaxial piping, is demonstrated via a series of parameter studies. We also investigate the effect of parameter uncertainties, and find that the imprecise knowledge of the tritium solubility in PbLi in particular leads to very disparate estimates of tritium losses. Depending on the experimental value used, losses range from ~0.05 to over 6 grams of tritium per year. As a result, the former is acceptable based on estimated environmental releases and resultant dose to members of the public; the latter exceeds regulatory limits.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

3D printing synthesis of catalysts

The catalyst industry generates approximately $20 billion every year globally and plays a major role in the energy production sector. Traditional industrial catalysts (e.g., pellets) typically have mass and heat transfer limitations, and cause a pressure drop in continuous-flow reactors, lowering the efficiency of the catalytic processes. 3D printing technology has evolved rapidly over the past decade, and the 3D printing of catalysts with desired geometries can address many of the above-stated challenges with traditional catalysts. However, challenges remain to be addressed and opportunities remain to be explored before the full potential in the design and 3D printing of novel catalysts can be realized. Herein this article reviews the recent development in the 3D printing of catalysts. It summarizes the 3D printing design, dimension, property, and performance of 3D printed catalysts. The applications of 3D printed catalysts, such as reforming, wastewater treatment, and CO 2 capture and removal, are discussed, with a techno-economic analysis and life cycle analysis. Future research directions and opportunities for 3D printing of catalysts are also highlighted.

25 ENERGY STORAGE↗

Nitrogen removal from digested slurries using a simplified ammonia stripping technique

Highlights: • A novel application of N stripping for anaerobic digestates was studied. • The studied process combines mixing, pH adjustment and continuous air flow. •High ammonia removal efficiency (87%) was achieved at pH 9 and 40 {sup °}C. • Acceptable ammonia removal efficiency (69%) was achieved without pH adjustment. • Technique is a viable option for farms especially combined with biogas plants. - Abstract: This study assessed a novel technique for removing nitrogen from digested organic waste based on a slow release of ammonia that was promoted by continuous mixing of the digestate and delivering a continuous air stream across the surface of the liquid. Three 10-day experiments were conducted using two 50-L reactors. In the first two, nitrogen removal efficiencies were evaluated from identical digestates maintained at different temperatures (30 °C and 40 °C). At the start of the first experiment, the digestates were adjusted to pH 9 using sodium hydroxide, while in the second experiment pH was not adjusted. The highest ammonia removal efficiency (87%) was obtained at 40 °C with pH adjustment. However at 40 °C without pH adjustment, removal efficiencies of 69% for ammonia and 47% for total nitrogen were obtained. In the third experiment two different digestates were tested at 50 °C without pH adjustment. Although the initial chemical characteristics of the digestates were different in this experiment, the ammonia removal efficiencies were very similar (approximately 85%). Despite ammonia removal, the pH increased in all experiments, most likely due to carbon dioxide stripping that was promoted by temperature and mixing. The technique proved to be suitable for removing nitrogen following anaerobic digestion of livestock manure because effective removal was obtained at natural pH (≈8) and 40 °C, common operating conditions at typical biogas plants that process manure. Furthermore, the electrical energy requirement to operate the process is limited (estimated to be 3.8 kW h m{sup −3} digestate). Further improvements may increase the efficiency and reduce the processing time of this treatment technique. Even without these advances slow-rate air stripping of ammonia is a viable option for reducing the environmental impact associated with animal manure management.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗