Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “diffractive optics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
DOE OSTI2016

Structural and optical properties of Cd{sup 2+} ion on the growth of sulphamic acid single crystals

Transparent single crystals of Cadmium doped Sulphamic acid (SA) was grown by Conventional slow evaporation solution technique (SEST) which had the size of 13 × 8 × 7 mm{sup 3}. The grown single crystals have been characterized using single crystal X-ray diffraction UV-visible Spectral studies and Second harmonic generation (SHG) efficiency and the results were discussed. The lattice parameters of the grown Cd{sup 2+} ion doped SA crystal are confirmed by single crystal X-ray diffraction and belong to orthorhombic system. Optical transmittance of the crystal was recorded using UV-vis NIR spectrophotometer with its lower cut off wavelength around 259nm. SHG measurements indicate that the SHG efficiency of the grown Cd{sup 2+} ion doped SA crystal at a fundamental wavelength of 1064 nm is approximately equal to KDP.

36 MATERIALS SCIENCE↗
NASA NTRS1992

Combining ray-trace and diffraction analysis: A design example

An example is presented of using a combined ray trace and diffraction modeling code to simulate effects of objective-lens tilt in an optical data storage device. In some cases, neither ray-trace analysis nor diffraction analysis can give an adequate description of an optical system. The designer that is faced with the problem of analyzing such a system is forced to use a ray-trace program to determine aberrations in the exit pupil and then introduce aberration coefficients into a diffraction model that simulate the propagation. This approach was found rather awkward, especially if complicated aberrations are present. Our approach is to integrate a diffraction analysis and a ray-trace description of an optical path into one program. Our design is taken from a data storage application, where we must analyze the effects of objective-lens tilt.

Milster, Tom D.↗
NASA NTRS1975

Stream pattern analysis using optical processing of ERTS imagery of Kansas

A spatial frequency analysis was carried out to obtain large-scale geologic and other ground pattern spatial frequency and orientational data from an optical data processing system using Earth Resources Technology Satellite-1 (ERTS-1) imagery of Kansas as input. The Diffraction Pattern Sampling Unit (DPSU) of the optical data processing system consists of a photodiode array containing 32 wedge-shaped photodiodes and 32 annular ring diodes. The curve obtained from the intensity distribution of the frequency spectrum yielded by the ring diodes gives the spatial frequency contributions due to ground features on the image. The curve obtained from the wedge-shaped diodes indicates the orientation of features in the sample area. Ten sample sites were used for each of eight geologic-physiographic regions. Comparison of ERTS-1 images with their respective spatial frequency and orientational curves reveals that preferred orientations of drainage produce recognizable peaks.

Mccauley, J.↗
DOE OSTI2015

Optically switchable natural silk

An optically active bio-material is created by blending natural silk fibers with photoisomerizable chromophore molecules—azobenzenebromide (AzBr). The material converts the energy of unpolarized light directly into mechanical work with a well-defined direction of action. The feasibility of the idea to produce optically driven microsized actuators on the basis of bio-material (silk) is proven. The switching behavior of the embedded AzBr molecules was studied in terms of UV/Vis spectroscopy. To test the opto-mechanical properties of the modified fibers and the structural changes they undergo upon optically induced switching, single fiber X-ray diffraction with a micron-sized synchrotron radiation beam was combined in situ with optical switching as well as with mechanical testing and monitoring. The crystalline regions of silk are not modified by the presence of the guest molecules, hence occupy only the amorphous part of the fibers. It is shown that chromophore molecules embedded into fibers can be reversibly switched between the trans and cis conformation by illumination with light of defined wavelengths. The host fibers respond to this switching with a variation of the internal stress. The amplitude of the mechanical response is independent of the applied external stress and its characteristic time is shorter than the relaxation time of the usual mechanical response of silk.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Dynamics of McMillan mappings II. axially symmetric map

Here, in this article, we investigate the transverse dynamics of a single particle in a model integrable accelerator lattice, based on a McMillan axially-symmetric electron lens. Although the McMillan e-lens has been considered as a device potentially capable of mitigating collective space charge forces, some of its fundamental properties have not been described yet. The main goal of our work is to close this gap and understand the limitations and potentials of this device. It is worth mentioning that the McMillan axially symmetric map provides the first-order approximations of dynamics for a general linear lattice plus an arbitrary thin lens with motion separable in polar coordinates. Therefore, advancements in its understanding should give us a better picture of more generic and not necessarily integrable round beams. In the first part of the article, we classify all possible regimes with stable trajectories and find the canonical action-angle variables. This provides an evaluation of the dynamical aperture, Poincaré rotation numbers as functions of amplitudes, and thus determines the spread in nonlinear tunes. Also, we provide a parameterization of invariant curves, allowing for the immediate determination of the map image forward and backward in time. The second part investigates the particle dynamics as a function of system parameters. We show that there are three fundamentally different configurations of the accelerator optics causing different regimes of nonlinear oscillations. Each regime is considered in great detail, including the limiting cases of large and small amplitudes. In addition, we analyze the dynamics in Cartesian coordinates and provide a description of observable variables and corresponding spectra.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
NASA NTRS1989

Optical Receivers With Rough Reflectors

Receiver for optical communications uses rough reflector instead of diffraction-limited reflector customarily thought necessary for such systems. Rough reflector collects and focuses optical signal. Other receiver components include narrow-passband optical filter to reject out-of-band background radiation, spatial filter to limit receiver field of view, optical-detector array (typically two concentric detectors), and postdetection processor to reconstruct transmitted message.

Vilnrotter, Victor A.↗
DOE OSTI2015

Diffraction limited focusing and routing of gap plasmons by a metal-dielectric-metal lens

Passive optical elements can play key roles in photonic applications such as plasmonic integrated circuits. Here we experimentally demonstrate passive gap-plasmon focusing and routing in two-dimensions. This is accomplished using a high numerical-aperture metal-dielectric-metal lens incorporated into a planar-waveguide device. Fabrication via metal sputtering, oxide deposition, electron- and focused-ion- beam lithography, and argon ion-milling is reported on in detail. Diffraction-limited focusing is optically characterized by sampling out-coupled light with a microscope. The measured focal distance and full-width-half-maximum spot size agree well with the calculated lens performance. The surface plasmon polariton propagation length is measured by sampling light from multiple out-coupler slits.

42 ENGINEERING↗
DOE OSTI2018

X-Ray Sum Frequency Diffraction for Direct Imaging of Ultrafast Electron Dynamics

X-ray diffraction from molecules in the ground state produces an image of their charge density, and time-resolved x-ray diffraction can thus monitor the motion of the nuclei. However, the density change of excited valence electrons upon optical excitation can barely be monitored with regular diffraction techniques due to the overwhelming background contribution of the core electrons. We present a nonlinear x-ray technique made possible by novel free electron laser sources, which provides a spatial electron density image of valence electron excitations. The technique, sum frequency generation carried out with a visible pump and a broadband x-ray diffraction pulse, yields snapshots of the transition charge densities, which represent the electron density variations upon optical excitation. The technique is illustrated by ab initio simulations of transition charge density imaging for the optically induced electronic dynamics in a donor or acceptor substituted stilbene.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2011

Control Program and Optical Improvements of Fresnel Microspectrometer

A microspectrometer has a circular geometry, and is designed with the Fresnel diffraction equation. This enables a dramatic miniaturization of the optical parts of a spectrometer over 100 times by volume. Therefore, it enables the construction of spectrometer arrays such as 100X100 microspectrometers for tunable multispectral or hyper-spectral imaging. It can be used for a massive, simultaneous spectral scan from multiple optical sources such as 10,000 optical fibers.

Park, Yeonjoon↗
DOE OSTI2022

Diamond formation in double-shocked epoxy to 150 GPa

We present measurements of diamond formation in doubly shocked Stycast 1266 epoxy (comprising C, H, Cl, N, and O) using in situ x-ray diffraction. Epoxy samples were reshocked against a LiF window to pressures between 80 and 148 GPa in experiments at the Omega Laser Facility. Furthermore, the pressure and temperature conditions were diagnosed in situ using velocimetry and optical pyrometry, respectively. X-ray diffraction patterns of the compressed epoxy are consistent with cubic diamond (Fd3¯m), indicating that diamond can precipitate not only from twice-shocked CH polystyrene [Kraus et al. Nat. Astron. 1, 606 (2017)] at these conditions but also from twice-shocked CH polymers with the addition of oxygen, nitrogen, and chlorine. These results, in combination with previous works on CH, CH 2 , CH 4 , and methane hydrate, support that diamond often, but not always, forms from CH-based compounds at extreme pressures and temperatures, indicating that the chemical composition, thermodynamic compression path, and kinetics play an important role.

36 MATERIALS SCIENCE↗
NASA NTRS1993

Correcting for diffraction in the far-infrared reflectance measurement of rough surfaces

The manner in which diffraction can increase the reflectance measured from very rough surfaces is shown by observations of diffracted light within the instrument profile of a far-IR reflectometer system. A correction to the calibration signal based on numerical integration of the diffracted part of the instrument profile is described. Diffraction correction factors as large as 2.94 have been found with small optics at long wavelength (630 microns). The effect of diffraction on diffuse reflectance measurements of a very rough perfect reflector is shown at wavelengths from 56 to 200 microns.

Smith, Sheldon M.↗
DOE OSTI2015

A facile synthesis of metal nanoparticle - graphene composites for better absorption of solar radiation

Herein, a facile chemical approach has been adopted to prepare silver nanoparticles (AgNPs)- graphene (G) composite to study photothermal effect. Sodium borohydride (SBH), a strong reducing agent has been selected for this work. Effect of SBH concentrations on optical behavior of AgNPs-G composite was also investigated. Resultant materials were characterized by various techniques including X-ray diffraction (XRD), fourier transform infrared spectroscopy (FTIR), optical absorption, scanning electron microscopy (SEM) and transmission electron microscopy (TEM). SEM micrographs confirm wrapping of AgNPs into graphene whereas XRD analysis reveals their particle size variation between 47 nm to 69 nm. Optical studies throw a light on their strong absorption behavior towards solar radiation.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1984

Laboratory demonstration of image reconstruction for coherent optical system of modular imaging collectors (COSMIC)

The first physical demonstration of the principle of image reconstruction using a set of images from a diffraction-blurred elongated aperture is reported. This is an optical validation of previous theoretical and numerical simulations of the COSMIC telescope array (coherent optical system of modular imaging collectors). The present experiment utilizes 17 diffraction blurred exposures of a laboratory light source, as imaged by a lens covered by a narrow-slit aperture; the aperture is rotated 10 degrees between each exposure. The images are recorded in digitized form by a CCD camera, Fourier transformed, numerically filtered, and added; the sum is then filtered and inverse Fourier transformed to form the final image. The image reconstruction process is found to be stable with respect to uncertainties in values of all physical parameters such as effective wavelength, rotation angle, pointing jitter, and aperture shape. Future experiments will explore the effects of low counting rates, autoguiding on the image, various aperture configurations, and separated optics.

Traub, W. A.↗
DOE OSTI2017

A compact fiber optics-based heterodyne combined normal and transverse displacement interferometer

While Photonic Doppler Velocimetry (PDV) has become a common diagnostic tool for the measurement of normal component of particle motion in shock wave experiments, this technique has not yet been modified for the measurement of combined normal and transverse motion, as needed in oblique plate impact experiments. In this study, we discuss the design and implementation of a compact fiber-optics-based heterodyne combined normal and transverse displacement interferometer. Like the standard PDV, this diagnostic tool is assembled using commercially available telecommunications hardware and uses a 1550 nm wavelength 2 W fiber-coupled laser, an optical focuser, and single mode fibers to transport light to and from the target. Two additional optical probes capture first-order beams diffracted from a reflective grating at the target free-surface and deliver the beams past circulators and a coupler where the signal is combined to form a beat frequency. The combined signal is then digitized and analyzed to determine the transverse component of the particle motion. The maximum normal velocity that can be measured by this system is limited by the equivalent transmission bandwidth (3.795 GHz) of the combined detector, amplifier, and digitizer and is estimated to be ~2.9 km/s. Finally, sample symmetric oblique plate-impact experiments are performed to demonstrate the capability of this diagnostic tool in the measurement of the combined normal and transverse displacement particle motion.

47 OTHER INSTRUMENTATION↗
DOE OSTI2018

Formation of Cu{sub 2}O and ZnO Crystal Layers by Magnetron Assisted Sputtering and Their Optical Characterization

Copper (I) oxide and zinc oxide films are formed on silicon and glassy quartz substrates by magnetron assisted sputtering. The thickness of the films is tens and hundreds of nanometers. The films are grown at different substrate temperatures and different oxygen pressures in the working chamber. The film samples are studied by the X-ray diffraction technique, scanning electron microscopy, and optical methods. It is established that an increase in the substrate temperature yields a change in the surface morphology of copper (I) oxide films towards the formation of well-pronounced crystallites. The reflectance and Raman spectra suggest that the quality of such films is close to that of bulk Cu{sub 2}O crystals produced by the oxidation of copper. As concerns ZnO films, an increase in the substrate temperature and an increase in the partial oxygen pressure make it possible to produce films, for which a sharp exciton structure is observed in the reflectance spectra and the emission of excitons bound at donors is observed in the luminescence spectra.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Rietveld analysis using powder diffraction data with anomalous scattering effect obtained by focused beam flat sample method

Focused-beam flat-sample method (FFM) is a new trial for synchrotron powder diffraction method, which is a combination of beam focusing optics, flat shape powder sample and area detectors. The method has advantages for X-ray diffraction experiments applying anomalous scattering effect (anomalous diffraction), because of 1. Absorption correction without approximation, 2. High intensity X-rays of focused incident beams and high signal noise ratio of diffracted X-rays 3. Rapid data collection with area detectors. We applied the FFM to anomalous diffraction experiments and collected synchrotron X-ray powder diffraction data of CoFe{sub 2}O{sub 4} (inverse spinel structure) using X-rays near Fe K absorption edge, which can distinguish Co and Fe by anomalous scattering effect. We conducted Rietveld analyses with the obtained powder diffraction data and successfully determined the distribution of Co and Fe ions in CoFe{sub 2}O{sub 4} crystal structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Controllable synthesis of stoichiometric Cu{sub 2}ZnSnS{sub 4} nanoparticles by solvothermal method and its properties

This work reports the solvothermal synthesis of earth abundant Cu{sub 2}ZnSnS{sub 4} (CZTS) nanoparticles and their structural, morphological, chemical and optical properties. The X-ray diffraction and Raman spectroscopy confirmed the formation of single phase CZTS with kesterite crystal structure. Transmission electron microscopy showed the formation of well-dispersed CZTS nanoparticles having a size ∼ 6 to 12 nm. The stoichiometric ratio of relative elemental of Cu: Zn: Sn: S is confirmed from the energy dispersive spectrometer. The optical absorption studies revealed that CZTS nanoparticles had an optical band gap of 1.52 eV, which is the optimal for the photovoltaic applications. The surfactant HMTA plays a key role in the synthesis of CZTS nanoparticles. Finally, a possible reaction mechanism for the formation of CZTS nanoparticles is proposed.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2015

Pre-nitridation induced In incorporation in In{sub x}Ga{sub 1−x}N nanorods on Si(111) grown by molecular beam epitaxy

We address the issue of obtaining high quality green emitting InGaN nanorods without any phase separation. Role of pre-nitridation of the Si(111) substrate and growth, temperature on the morphology, structural and optical properties of In{sub x}Ga{sub 1−x}N films grown by plasma assisted molecular beam epitaxy, has been studied. The nitrogen rich growth environment and surface nitridation results in the formation of vertically well-aligned single crystalline nanorods that are coalesced and isolated at 400 °C and 500 °C, respectively. In incorporation is also seen to be enhanced to ≈28% at 400 °C to yield a stable green emission, while the nanorods grown at 500 °C show blue band-edge emission. The orientation, phase separations, and optical properties characterized by Reflection High Energy Electron Diffraction, Field Emission Scanning Electron Microscopy, high resolution x-ray diffraction, x-ray photoelectron spectroscopy, and photoluminescence are corroborated to understand the underlying mechanism. The study optimizes conditions to grow high quality catalyst-free well-aligned InGaN rods on nitrided Si surface, whose band-edge emission can be tuned from blue to green by sheer control of the substrate temperature.

36 MATERIALS SCIENCE↗