Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “device characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

InP and GaAs characterization with variable stoichiometry obtained by molecular spray

Both InP and GaAs surfaces were studied in parallel. A molecular spray technique was used to obtain two semiconductor surfaces with different superficial compositions. The structures of these surfaces were examined by electron diffraction. Electron energy loss was measured spectroscopically in order to determine surface electrical characteristics. The results are used to support conclusions relative to the role of surface composition in establishing a Schottky barrier effect in semiconductor devices.

Massies, J.↗
NASA NTRS1995

Multijunction InGaAs thermophotovoltaic power converter

The experimental performance of a multijunction monolithic In(0.53)Ga(0. 47)As power converter under blackbody irradiation is reported. Eight InGaAs PN junctions grown epitaxially on a semi-insulating wafer were monolithically integrated in series to boost the approximately 0.4 V photovoltage per typical InGaAs junction to over 3 volts for the 1 sq cm chip. This chip was originally designed and characterized for free-space 1.3 micron laser power beaming. This is the first report of such a multijunction TPV. This is not a traditional tandem cell in which the junctions are stacked vertically. The junctions are each about 1mm long by 1 cm wide and are laterally connected across the 1 sq cm device area. This multijunction design has the potential for lower I(sup 2)R power loss since the smaller PN junction area limits the current to one-eighth that of the equivalent surface area. In essence, the current is traded for voltage to avoid the I(sup 2)R loss, analogous to the way power utilities avoid I(sup 2)P loss in high-tension power lines, by transforming the high current, low voltage generated at a power plant into a high voltage at a low current before transmitting the power over great distances.

Wojtczuk, Steven↗
NASA NTRS2018

The Hayabusa2 Sample Return Mission and Its Small Carry-On Impactor Experiment

On December 3, 2014 the Hayabusa2 Spacecraft was launched by JAXA to investigate and return samples from carbonaceous Asteroid (162173) Ryugu. The spacecraft's payload contains several remote sensing instruments that are designed to characterize the asteroid's surface and to help identify scientifically interesting locations from which samples can be obtained safely. The data collected by these instruments will also help place any obtained samples in context with respect to the global characteristics of Ryugu. In addition to the suite of remote sensing instruments and the sampling device, Hayabusa2 also includes a small carry-on impactor (SCI) payload experiment, which is designed to impact the surface of the asteroid and excavate fresh material for subsequent collection. The SCI consists of a 30 cm diameter 2 kg copper disk that is accelerated by an explosive charge into the surface of Ryugu at approximately 2 km/s. The resultant crater formed during this experiment is estimated to be approximately between 2 - 10 meters in diameter with an ejecta blanket extending to 10 - 100 meters on the asteroid. Hayabusa2 will not be able to observe the impact experiment directly due to considerations of spacecraft safety since there is some risk of collisions with debris from the explosion and ejecta from the crater. However, prior to moving safely away, the spacecraft will deploy a small imaging system called Deployable Camera 3 (DCAM3). DCAM3 will detach from Hayabusa2 just before the detonation of the SCI and will image the moment of impact, crater formation, and ejecta propagation. These data will be transmitted to Hayabusa2 and will help constrain the near-surface properties of Ryugu and also impact scaling laws for small bodies in low gravity environments. These data could also be useful for gaining insights into determining asteroid physical properties from higher velocity impact events (e.g., DART and HERA data of Didymos).

Abell, Paul A.↗
NASA NTRS1981

Bypass diode integration

Protective bypass diodes and mounting configurations which are applicable for use with photovoltaic modules having power dissipation requirements in the 5 to 50 watt range were investigated. Using PN silicon and Schottky diode characterization data on packaged diodes and diode chips, typical diodes were selected as representative for each range of current carrying capacity, an appropriate heat dissipating mounting concept along with its environmental enclosure was defined, and a thermal analysis relating junction temperature as a function of power dissipation was performed. In addition, the heat dissipating mounting device dimensions were varied to determine the effect on junction temperature. The results of the analysis are presented as a set of curves indicating junction temperature as a function of power dissipation for each diode package.

Shepard, N. F., Jr.↗
NASA NTRS1985

Microgravity Silicon Zoning Investigation

This research program is directed toward the understanding of the float zone crystal growth process, the melt interactions which lead to crystal inhomogeneities, and the influence of microgravity on reducing these inhomogeneities. Silicon was selected as the model crystal because its inhomogeneities lead to known variations in device performance, and because the mechanisms involved in its growth are understood better than for other high temperature crystals. The objective of the program is to understand the growth mechanisms in float zone growth and thereby determine the feasibility and advantages of float zone growth of silicon under microgravity conditions. This will be done by characterizing the growth at g = 1, projecting the changes in melt flows due to microgravity, observing these in space growth and determining the effects on defective inhomogeneities. A Thin Rod Zoner was constructed as a laboratory prototype for flight growth of 5 mm diameter silicon crystals, which can be done within the power and cooling capabilities of shuttle flights. A new method of zoning silicon, using resistance heating, has resulted in melting 5 mm diameter ingots.

E L Kern↗
NASA NTRS1986

Nondestructive characterization of RBSOA of high-power bipolar transistors

Reverse-bias safe operating area (RBSOA) of high-power Darlington transistors is characterized using a 120 A/1000 V nondestructive reverse-bias second breakdown tester designed and fabricated at Virginia Polytechnic Institute and State University. Elaborate RBSOA characteristics are generated with different forward/reverse base drives and collector current levels. The effects of elevated case temperature and second-base drive on RBSOA of four-terminal Darlington devices are also discussed.

Jovanovic, M. M.↗
NASA NTRS2004

Glow Discharge Plasma Demonstrated for Separation Control in the Low-Pressure Turbine

Flow separation in the low-pressure turbine (LPT) is a major barrier that limits further improvements of aerodynamic designs of turbine airfoils. The separation is responsible for performance degradation, and it prevents the design of highly loaded airfoils. The separation can be delayed, reduced, or eliminated completely if flow control techniques are used. Successful flow control technology will enable breakthrough improvements in gas turbine performance and design. The focus of this research project was the development and experimental demonstration of active separation control using glow discharge plasma (GDP) actuators in flow conditions simulating the LPT. The separation delay was shown to be successful, laying the foundation for further development of the technologies to practical application in the LPT. In a fluid mechanics context, the term "flow control" means a technology by which a very small input results in a very large effect on the flow. In this project, the interest is to eliminate or delay flow separation on LPT airfoils by using an active flow control approach, in which disturbances are dynamically inserted into the flow, they interact with the flow, and they delay separation. The disturbances can be inserted using a localized, externally powered, actuating device, examples are acoustic, pneumatic, or mechanical devices that generate vibrations, flow oscillations, or pulses. A variety of flow control devices have been demonstrated in recent years in the context of the external aerodynamics of aircraft wings and airframes, where the incoming flow is quiescent or of a very low turbulence level. However, the flow conditions in the LPT are significantly different because there are high levels of disturbances in the incoming flow that are characterized by high free-stream turbulence intensity. In addition, the Reynolds number, which characterizes the viscous forces in the flow and is related to the flow speed, is very low in the LPT passages.

Ashpis, David e.↗
NASA NTRSDate not supplied

Coherent Mode Decomposition for Kolmogorov Optical Turbulence in a Finite Aperture

An analysis of the coherent mode decomposition of an optical field after propagation through atmospheric turbulence is presented. The coherent modes represent an ideal basis by which to decompose the field for design of mode-limited optical systems. Using the rotational symmetry of the Fredholm integral operator for Kolmogorov optical turbulence, it is shown that the coherent modes exhibit separable solutions classified by radial and azimuthal quantum numbers. The study of the coherent modes is then reduced that of the radial functions determined by the aperture-coherence diameter ratio and obscuration ratio. Analysis of the spectrum of eigenvalues yields sharp bounds on the efficiency of receivers using incoherent or coherent combining with mode-limited photonic devices in the presence of Kolmogorov turbulence. The effective number of modes needed to represent Kolmogorov optical turbulence is studied via the von Neumann entropy, purity, and largest eigenvalue, and the differences in the different definitions is discussed. The similarity of the coherent modes to linearly polarized (LP) fiber modes is quantified yielding a precise characterization of the maximum gain that can be achieved in mode-limited systems via mode shaping techniques. As a final application, a mode sorting technique is presented for optimally splitting power from atmospherically degraded light into a finite number of modes simultaneously maximizing total coupling efficiency and minimizing the average and instantaneous power ratio between channels.

free-space optical communication↗
NASA NTRSDate not supplied

Coherent Mode Decomposition for Kolmogorov Optical Turbulence in a Finite Aperture

An analysis of the coherent mode decomposition of an optical field after propagation through atmospheric turbulence is presented. The coherent modes represent an ideal basis by which to decompose the field for design of mode-limited optical systems. Due to rotational symmetry of the Fredholm integral operator for Kolmogorov optical turbulence, the coherent modes exhibit separable solutions classified by a radial and azimuthal mode index. The study of the coherent modes is then reduced to that of the radial functions determined by the coherence ratio and obscuration ratio. Analysis of the spectrum of eigenvalues yields sharp bounds on the efficiency of receivers using incoherent or coherent combining with mode-limited photonic devices in the presence of Kolmogorov turbulence. The effective number of modes needed to represent Kolmogorov optical turbulence is studied via the von Neumann entropy, purity, and largest eigenvalue, and the differences in the different definitions is discussed. The similarity of the coherent modes to linearly polarized (LP) fiber modes is quantified yielding a precise characterization of the maximum gain that can be achieved in mode-limited systems via mode shaping techniques. As a final application, a mode sorting technique is presented for optimally splitting power from atmospherically degraded light into a finite number of modes simultaneously maximizing total coupling efficiency and minimizing the difference in average power between channels.

free-space optical communication↗
NASA NTRS2007

Measurement and Simulation of the Variation in Proton-Induced Energy Deposition in Large Silicon Diode Arrays

The proton induced charge deposition in a well characterized silicon P-i-N focal plane array is analyzed with Monte Carlo based simulations. These simulations include all physical processes, together with pile up, to accurately describe the experimental data. Simulation results reveal important high energy events not easily detected through experiment due to low statistics. The effects of each physical mechanism on the device response is shown for a single proton energy as well as a full proton space flux.

Howe, Christina L.↗
NASA NTRS2008

Portable Device Analyzes Rocks and Minerals

inXitu Inc., of Mountain View, California, entered into a Phase II SBIR contract with Ames Research Center to develop technologies for the next generation of scientific instruments for materials analysis. The work resulted in a sample handling system that could find a wide range of applications in research and industrial laboratories as a means to load powdered samples for analysis or process control. Potential industries include chemical, cement, inks, pharmaceutical, ceramics, and forensics. Additional applications include characterizing materials that cannot be ground to a fine size, such as explosives and research pharmaceuticals.

Source record↗
NASA NTRS1990

256 x 256 PACE-1 PV HgCdTe focal plane arrays for medium and short wavelength infrared applications

The development of two 256 by 256 hybrid HgCdTe focal plane array (FPA) families is described, and their performance is discussed. The hybrid FPAs employ a PV HgCdTe detector array and custom Si CMOS readouts. The PACE-1 process was used to fabricate the detectors, whereby the liquid phase epitaxial growth of HgCdTe occurs on sapphire substrates buffered by a layer of CdTe. The performance characteristics of the detector arrays are given. A tactical 256 by 256 CMOS readout is tested, in which a high functional yield was achieved. Updated test results are given for a 256 by 256 readout circuit developed for use in an orbital replacement instrument for the Hubble Space Telescope. The characterizations of several MWIR and SWIR FPAs were thorough and shown to be reliable. The pixel yield, maximum FPA responsivity nonuniformity, and SWIR FPA read noise for the tests are given. The high contrast and insignificant fixed pattern noise of the imagery from the MWIR 256 by 256 FPA are emphasized. These qualities were obtained when the device was operating at 80 k and utilizing f/2 optics with an 8-in. focal length and a 4.4 micron high pass filter.

Kozlowski, L. J.↗
NASA NTRS1992

Adaptive attitude control and momentum management for large-angle spacecraft maneuvers

The fully coupled equations of motion are systematically linearized around an equilibrium point of a gravity gradient stabilized spacecraft, controlled by momentum exchange devices. These equations are then used for attitude control system design of an early Space Station Freedom flight configuration, demonstrating the errors caused by the improper approximation of the spacecraft dynamics. A full state feedback controller, incorporating gain-scheduled adaptation of the attitude gains, is developed for use during spacecraft on-orbit assembly or operations characterized by significant mass properties variations. The feasibility of the gain adaptation is demonstrated via a Space Station Freedom assembly sequence case study. The attitude controller stability robustness and transient performance during gain adaptation appear satisfactory.

Parlos, Alexander G.↗
NASA NTRS1993

Cryogenic measurements of aerojet GaAs n-JFETs

The spectral noise characteristics of Aerojet gallium arsenide (GaAs) junction field effect transistors (JFET's) have been investigated down to liquid-helium temperatures. Noise characterization was performed with the field effect transistor (FET) in the floating-gate mode, in the grounded-gate mode to determine the lowest noise readings possible, and with an extrinsic silicon photodetector at various detector bias voltages to determine optimum operating conditions. The measurements indicate that the Aerojet GaAs JFET is a quiet and stable device at liquid helium temperatures. Hence, it can be considered a readout line driver or infrared detector preamplifier as well as a host of other cryogenic applications. Its noise performance is superior to silicon (Si) metal oxide semiconductor field effect transistor (MOSFET's) operating at liquid helium temperatures, and is equal to the best Si n channel junction field effect transistor (n-JFET's) operating at 300 K.

Goebel, John H.↗
NASA NTRS2013

High-Power Single-Mode 2.65-micron InGaAsSb/AlInGaAsSb Diode Lasers

Central to the advancement of both satellite and in-situ science are improvements in continuous-wave and pulsed infrared laser systems coupled with integrated miniaturized optics and electronics, allowing for the use of powerful, single-mode light sources aboard both satellite and unmanned aerial vehicle platforms. There is a technological gap in supplying adequate laser sources to address the mid-infrared spectral window for spectroscopic characterization of important atmospheric gases. For high-power applications between 2 to 3 micron, commercial laser technologies are unsuitable because of limitations in output power. For instance, existing InP-based laser systems developed for fiber-based telecommunications cannot be extended to wavelengths longer than 2 micron. For emission wavelengths shorter than 3 micron, intersubband devices, such as infrared quantum cascade lasers, become inefficient due to band-offset limitations. To date, successfully demonstrated singlemode GaSb-based laser diodes emitting between 2 and 3 micron have employed lossy metal Bragg gratings for distributed- feedback coupling, which limits output power due to optical absorption. By optimizing both the quantum well design and the grating fabrication process, index-coupled distributed-feedback 2.65-micron lasers capable of emitting in excess of 25 mW at room temperature have been demonstrated. Specifically, lasers at 3,777/cm (2.65 micron) have been realized to interact with strong absorption lines of HDO and other isotopologues of H2O. With minor modifications of the optical cavity and quantum well designs, lasers can be fabricated at any wavelength within the 2-to-3-micron spectral window with similar performance. At the time of this reporting, lasers with this output power and wavelength accuracy are not commercially available. Monolithic ridge-waveguide GaSb lasers were fabricated that utilize secondorder lateral Bragg gratings to generate single-mode emission from InGaAsSb/ AlInGaAsSb multi-quantum well structures. The device fabrication utilizes etched index-coupled gratings in the top AlGaAsSb cladding of the laser chip along the ridge waveguide, whereas commercial lasers that emit close to this wavelength include loss-coupled metal gratings that limit the output power of the laser. Semiconductor-laser-based spectrometers can be used to replace gas sensors currently used in industry and government. With the availability of high-power laser sources at mid-infrared wavelengths, sensors can target strong fundamental gas absorption lines to maximize instrument sensitivity.

Frez, Clifford F.↗
NASA NTRSDate not supplied

Metal Fused Filament Fabrication of Titanium Alloy for In Space Manufacturing

NASA is developing materials and processes for the in-space manufacturing of many items for the International Space Station (ISS) and future exploration platforms. These new manufacturing processes will require the further development of current 3D printing processes to achieve high-performance metal parts within the power and space constraints of the ISS. Manufacturing Ti-6Al-4V alloy parts with 3D printing using a metal fused filament fabrication (MF3) process is an alternative process to the Direct Metal Laser Sintering (DMLS) of the metal powders additive manufacturing process. Our initial work fabricating Ti-6Al-4V parts from Ti-6Al-4V powder-binder feedstock and processed with the MF3 process has resulted in 95-97% sintered densities. The current development work of optimized sintered properties investigates the effects of variation in sintering time, temperature, and vacuum on the sintered properties of Ti-6Al-4V MF3 printed tensile bars. Sintered properties such as density, hardness, and tensile properties were characterized followed by microstructural and chemical (O/C/N) analysis to understand the role of sintering process on the ensuing material properties. Future development of the MF3 process will also involve investigation of the effects of micro-milling the Ti-64Al-4V powder to nanometer particle sizes and the investigation of laser sintering of the 3D printed devices. This new micro-milling technique will have broad application to other areas that require particle size reduction of hard metallic materials, such as Nuclear Thermal Propulsion and other NASA technologies. Laser sintering in lieu of high temperature thermal sintering should allow for significant power reduction and improved processing speeds.

sintering, alloys, 3D printing↗
NASA NTRS1984

Electro-optical terrain reflectance modeling - A perspective

Electro-optical terrain reflectance modeling is one of the components required in the overall capability to simulate remote sensing measurement systems as an aid to the sensor or information processing designer. Given that sensor fields-of-view may vary from a few centimeters to several meters and that measurement devices may be placed at varying heights above the terrain surface, modeling of complex combinations of terrain classes or media with respect to both vertical and horizontal scales may be required. This paper addresses the issue of combining modeling approaches for different classes of materials in the optical regime and recommends a more formal approach to the radiative characterization of media properties as well as the calculation of the bidirectional reflectance distribution functions.

Smith, J. A.↗
NASA NTRS1993

Low power arcjet system spacecraft impacts

Application of electrothermal arcjets on communications satellites requires assessment of integration concerns identified by the user community. Perceived risks include plume contamination of spacecraft materials, induced arcing or electrostatic discharges between differentially charged spacecraft surfaces, and conducted and radiated electromagnetic interference (EMI) for both steady state and transient conditions. A Space Act agreement between Martin Marietta Astro Space, the Rocket Research Company, and NASA's Lewis Research Center was established to experimentally examine these issues. Spacecraft materials were exposed to an arcjet plume for 40 hours, representing 40 weeks of actual spacecraft life, and contamination was characterized by changes in surface properties. With the exception of the change in emittance of one sample, all measurable changes in surface properties resulted in acceptable end of life characteristics. Charged spacecraft samples were benignly and consistently reduced to ground potential during exposure to the powered arcjet plume, suggesting that the arcjet could act as a charge control device on spacecraft. Steady state EMI signatures obtained using two different power processing units were similar to emissions measured in a previous test. Emissions measured in UHF, S, C, Ku and Ka bands obtained a null result which verified previous work in the UHF, S, and C bands. Characteristics of conducted and radiated transient emissions appear within standard spacecraft susceptibility criteria.

Pencil, Eric J.↗