Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “beam techniques”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 955 records · Page 53
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Gigabit Satellite Network for NASA's Advanced Communication Technology Satellite (ACTS)

The advanced communication technology satellite (ACTS) gigabit satellite network provides long-haul point-to-point and point-to-multipoint full-duplex SONET services over NASA's ACTS. at rates up to 622 Mbit/s (SONET OC-12), with signal quality comparable to that obtained with terrestrial fiber networks. Data multiplexing over the satellite is accomplished using time-division multiple access (TDMA) techniques coordinated with the switching and beam hopping facilities provided by ACTS. Transmissions through the satellite are protected with Reed-Solomon encoding. providing virtually error-free transmission under most weather conditions. Unique to the system are a TDMA frame structure and satellite synchronization mechanism that allow: (a) very efficient utilization of the satellite capacity: (b) over-the-satellite dosed-loop synchronization of the network in configurations with up to 64 ground stations: and (c) ground station initial acquisition without collisions with existing signalling or data traffic. The user interfaces are compatible with SONET standards, performing the function of conventional SONET multiplexers and. as such. can be: readily integrated with standard SONET fiber-based terrestrial networks. Management of the network is based upon the simple network management protocol (SNMP). and includes an over-the-satellite signalling network and backup terrestrial internet (IP-based) connectivity. A description of the ground stations is also included.

Hoder, Douglas↗
NASA NTRS2014

Mechanical Behavior of Microelectromechanical Microshutters

A custom micro-mechanical test system was constructed using off-the-shelf components to characterize the mechanical properties of microshutters. Microshutters are rectangular microelectromechanical apertures which open and close about a narrow torsion bar hinge. Displacement measurements were verified using both capacitive and digital image correlation techniques. Repeatable experiments on Si3N4 cantilever beams verified that the test system operates consistently. Using beam theory, the modulus of elasticity of the low stress Si3N4 was approximately 150 GPa, though significant uncertainty exists for this measurement due primarily to imprecise knowledge of the cantilever thickness. Tests conducted on microshutter arrays concluded that reducing the Si3N4 thickness from 250 nm to 500 nm reduces the torsional stiffness by a factor of approximately four. This is in good agreement with analytical and finite element models of the microshutters.

silicon nitride↗
NASA NTRSDate not supplied

A Study of the Kinematic and Dynamic Processes associated with Mesoscale Snowbands in a Midwest United States Snowstorm on 5 February 2020

Mesoscale snowbands are frequently responsible for dumping large amounts of snow over a relatively small region and pose a considerable forecasting challenge. The present study focuses on the mesoscale snowbands observed on 5 February 2020 over the Midwest United States. In order to improve the forecasting of mesoscale snowbands, it is important to understand the processes that organize these features. To this end, we are investigating the kinematic and dynamic processes that shape the mesoscale snowbands using a combination of high-altitude airborne radar, in-situ aircraft measurements, surface observations, and model simulations. This presentation will primarily focus on the three-dimensional structure of the mesoscale snowbands in terms of EXRAD reflectivity and horizontal winds. The horizontal winds are retrieved from the EXRAD scanning-beam Doppler velocities using a VAD technique. These winds, in combination with virtual potential temperature taken from the HRRR operational analysis, are used to compute the bulk Richardson number in order to investigate any contributions to banding features that might be tied to Kelvin-Helmholtz instability. Our analysis does not support the presence of Kelvin-Helmholtz instability. That said, low, but not subcritical, Richardson numbers were found near the top of some banding features in this event and it is possible that the model analysis is smoothing out the virtual potential temperature fields. Finally, we present arguments for using a flight module designed to sample the along-band structures with particular emphasis on observing generating cells and low-level microphysics.

Charles N. Helms↗
NASA NTRS2024

Evaluation of an Al-Cu-Zn-Mg Alloy for Wire-Fed Additive Manufacturing

A collaborative research study was conducted to evaluate an experimental Al-Cu-Zn-Mg alloy, designated Al C380H, developed by Arconic Corporation for wire-fed additive manufacturing (AM) techniques such as NASA’s electron beam freeform fabrication (EBF 3 ) process and the wire arc additive manufacturing (WAAM) process. The goal of the study was to determine, based upon metallurgical properties, whether additively manufactured Al C380H represented a viable alternative for applications currently using wrought 7xxx series aluminum. Al 2319 and Al 7075 were also deposited as AM-compatible and non-AM-compatible baselines, respectively. Evaluation was based on tensile, fracture, and corrosion properties. The strength and ductility of Al C380H-T6 materials produced by EBF3 and WAAM were sufficiently lower than typical values for Al 7050-T7 to indicate that additively manufactured Al C380H is not a viable replacement for current parts fabricated with Al 7050, due largely to the significant losses in Zn and Mg and development of porosity during deposition. EBF 3 parameters that reduced porosity, such as increasing electron beam current, higher raster frequency, sharper beam focus, and slower travel speed, augmented de-alloying of fugitive solute. Further enhancement of Zn and Mg content in Al C380H feedstock wire combined with adjustments to deposition conditions to minimize porosity may enable production of Al C380H parts by EBF 3 or WAAM that are viable replacements for current Al 7050 wrought products.

electron beam freeform fabrication (EBF3)↗
DOE OSTI2023

Exploring the Dynamics of Transverse Inter-planar Coupling in the Superconducting Section of the PIP-II LINAC

This study investigates the crucial role that an accurate understanding of inter-planar coupling in the transverse plane plays in regulating charged particle dynamics in a high intensity linear accelerator and minimizing foil/septum impacts during injection from the linac to a ring. We performed an in-depth analysis for the emergence and evolution of trans verse inter-planar coupling through multiple active lattice elements, taking into account space charge and field nonlinearities in the superconducting section of the PIP-II linac. The article compares various analytical, numerical, and experimental techniques for measuring transverse coupling using beam and lattice matrices and provides insight into effective strategies for its mitigation prior to ring injection.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2025

Elucidating the corrosion mechanism of Ni-based superalloys in the presence of uranium-containing chloride molten salt

The United States Department of Energy (DOE) is committed to the advancement of nuclear reactor technology through initiatives such as the Advanced Reactor Development Program (ARDP), in an effort to diversify the United States energy portfolio towards more sustainable energy options. The ARDP includes demonstration by industry partners of molten chloride fast reactors (MCFRs). Construction of MCFRs requires qualified nuclear structural materials. Unfortunately, there are no current materials that are fully qualified by the Nuclear Regulatory Commission for the construction of molten salt reactors, including MCFRs. Adapting current structural material qualifications requires expansion of our current knowledgebase on the property-performance relationships regarding corrosion performance. In this investigation, we assess microstructural changes in a Ni-based superalloy after exposure to a UCl3¬-containing chloride salt eutectic mixture through a correlated multi-modal approach combining several advanced characterization techniques, including scanning electron microscopy/focused ion beam (SEM/FIB) and transmission electron microscopy (TEM). SEM/FIB analysis will illustrate changes in elemental composition, microstructure, and isotopic information acquired from energy x-ray dispersive spectroscopy (EDS), electron backscatter diffraction (EBSD), and secondary ion mass spectroscopy (SIMS), respectively. This information will then aid in identifying localized regions to elucidate the corrosion mechanism with TEM through a combination of electron diffraction, electron energy loss spectroscopy (EELS), and additional EDS. The findings from this investigation will further expand our assessment of the corrosion performance of structural materials in molten salt chloride systems, aiding to developing fully qualified materials for construction of MCFRs.

36 MATERIALS SCIENCE↗
NASA NTRS1980

Power distribution for electron beam welding

The power distribution of an electron seam is analyzed. Digital computer techniques are used to evaluate the radial distribution of power detected by a wire probe circulating through the beam. Results are reported.

Edwards, E.↗
DOE OSTI2022

Phase-space tailoring and cooling of charged-particle beams for energy- and intensity-frontier applications

This project addressed accelerator science & technology researches relevant to the Intensity and Energy frontiers by investigating generic techniques to tailor and cool the phase-space distributions of charged-particle beams. Specifically, the project had two main research thrusts: (i) the development of phase-space tailoring techniques using externally-applied electromagnetic fields and (ii) the investigation of phase-space control using the beam’s self-field such as the optical-stochastic cooling (OSC). The work related to the development of phase-space-tailoring techniques leveraged on the research performed under our previous grant DE-SC0011831 where new temporal-shaping methods were proposed and some experimentally demonstrated. The work related to the concept of beam manipulation using self fields, and especially OSC, built on the achievements supported by grant DE-SC0013761 which focused on a OSC proof-of-principle experiment at the Fermilab’s IOTA ring.

43 PARTICLE ACCELERATORS↗
NASA NTRS2003

Efficient Coupling of Lasers to Telescopes with Obscuration

Two techniques have been proposed to increase the efficiency of coupling of light from lasers to Cassegrain telescopes and, in general, telescopes with secondary or tertiary mirror obscuration. The need to increase the efficiency of coupling arises in laser transmitters of lidar and freespace optical communication systems that utilize Cassegrain telescopes. The vignetting caused by the secondary reflector and baffle in such a telescope reduces the transmitted power by a large fraction because (1) the obscured area is central and is a significant fraction of the telescope aperture and (2) the cross-sectional intensity profile of a typical laser beam is Gaussian, so that intensity is greatest in the obscured central area. In a technique proposed previously for increasing the efficiency of coupling, an optical assembly comprising an axicon device and a folding mirror that would render the solid laser beam annular - in effect, turning the laser beam inside out - so that the laser light would be concentrated into an annular cross section that would not be obscured by the secondary reflector and baffle. Hence, most or all of the light would be coupled into the output beam. Another prior efficiency-enhancing technique is denoted subaperture illumination. In this technique, the laser beam is displaced laterally with respect to the optical axis of the secondary reflector, such that the beam impinges on an off-axis subaperture of the primary reflector that is not obscured by the secondary reflector and baffle.

Hemmati, Hamid↗
NASA NTRS2006

Automatic Alignment of Displacement-Measuring Interferometer

A control system strives to maintain the correct alignment of a laser beam in an interferometer dedicated to measuring the displacement or distance between two fiducial corner-cube reflectors. The correct alignment of the laser beam is parallel to the line between the corner points of the corner-cube reflectors: Any deviation from parallelism changes the length of the optical path between the reflectors, thereby introducing a displacement or distance measurement error. On the basis of the geometrical optics of corner-cube reflectors, the length of the optical path can be shown to be L = L(sub 0)cos theta, where L(sub 0) is the distance between the corner points and theta is the misalignment angle. Therefore, the measurement error is given by DeltaL = L(sub 0)(cos theta - 1). In the usual case in which the misalignment is small, this error can be approximated as DeltaL approximately equal to -L(sub 0)theta sup 2/2. The control system (see figure) is implemented partly in hardware and partly in software. The control system includes three piezoelectric actuators for rapid, fine adjustment of the direction of the laser beam. The voltages applied to the piezoelectric actuators include components designed to scan the beam in a circular pattern so that the beam traces out a narrow cone (60 microradians wide in the initial application) about the direction in which it is nominally aimed. This scan is performed at a frequency (2.5 Hz in the initial application) well below the resonance frequency of any vibration of the interferometer. The laser beam makes a round trip to both corner-cube reflectors and then interferes with the launched beam. The interference is detected on a photodiode. The length of the optical path is measured by a heterodyne technique: A 100- kHz frequency shift between the launched beam and a reference beam imposes, on the detected signal, an interferometric phase shift proportional to the length of the optical path. A phase meter comprising analog filters and specialized digital circuitry converts the phase shift to an indication of displacement, generating a digital signal proportional to the path length.

Halverson, Peter↗
DOE OSTI2024

Charge lifetime improvement of the Continuous Electron Beam Accelerator Facility photogun with a biased anode

GaAs photocathodes in dc high-voltage photoguns are highly susceptible to ion back-bombardment, which reduces the photocathode quantum efficiency and limits the useful operating lifetime for producing polarized electron beams. This paper demonstrates that applying a small positive bias to the photogun anode can significantly suppress ion back-bombardment and increase charge lifetime. This technique was studied extensively using the Continuous Electron Beam Accelerator Facility photogun, where highly polarized electron beams created using a strained-superlattice GaAs / GaAsP photocathode were used and charge lifetimes improved by almost a factor of 2. A new simulation code was developed to model ion production and tracking in order to better understand and explain the factors that led to the performance improvement. Results of the experiments and simulations are discussed in detail. Published by the American Physical Society 2024

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

Optically pumped polarized 3 He ++ ion source development for RHIC/EIC

The proposed polarized 3 He ++ acceleration in RHIC and the future Electron-Ion Collider will require about 2×10 11 ions in the source pulse. A new technique had been proposed for production of high intensity polarized 3 He ++ ion beams. It is based on ionization and accumulation of the 3 He gas (polarized by metastability-exchange optical pumping and in the 5T high magnetic field) in the existing Electron Beam Ion Source (EBIS). A novel 3 He cryogenic purification and storage technique was developed to provide the required gas purity. An original gas refill and polarized 3 He gas injection to the EBIS long drift tubes, (which serves as the storage cell) were developed to ensure polarization preservation. An infrared laser system for optical pumping and polarization measurements in the high 3–5 T field has been developed. The 3 He polarization 80–85% (and sufficiently long ~30 min relaxation time) was obtained in the “open” cell configuration with refilling valve tube inlet and isolation valve closed. The development of the spin-rotator and 3 He 4 He absolute nuclear polarimeter at 6 MeV 3 He ++ beam energy is also presented here in this work.

43 PARTICLE ACCELERATORS↗
NASA NTRS1996

Soot and Radiation Measurements in Microgravity Jet Diffusion Flames

The subject of soot formation and radiation heat transfer in microgravity jet diffusion flames is important not only for the understanding of fundamental transport processes involved but also for providing findings relevant to spacecraft fire safety and soot emissions and radiant heat loads of combustors used in air-breathing propulsion systems. Our objectives are to measure and model soot volume fraction, temperature, and radiative heat fluxes in microgravity jet diffusion flames. For this four-year project, we have successfully completed three tasks, which have resulted in new research methodologies and original results. First is the implementation of a thermophoretic soot sampling technique for measuring particle size and aggregate morphology in drop-tower and other reduced gravity experiments. In those laminar flames studied, we found that microgravity soot aggregates typically consist of more primary particles and primary particles are larger in size than those under normal gravity. Comparisons based on data obtained from limited samples show that the soot aggregate's fractal dimension varies within +/- 20% of its typical value of 1.75, with no clear trends between normal and reduced gravity conditions. Second is the development and implementation of a new imaging absorption technique. By properly expanding and spatially-filtering the laser beam to image the flame absorption on a CCD camera and applying numerical smoothing procedures, this technique is capable of measuring instantaneous full-field soot volume fractions. Results from this technique have shown the significant differences in local soot volume fraction, smoking point, and flame shape between normal and reduced gravity flames. We observed that some laminar flames become open-tipped and smoking under microgravity. The third task we completed is the development of a computer program which integrates and couples flame structure, soot formation, and flame radiation analyses together. We found good agreements between model predictions and experimental data for laminar and turbulent flames under both normal and reduced gravity. We have also tested in the laboratory the techniques of rapid-insertion fine-wire thermocouples and emission pyrometry for temperature measurements. These techniques as well as laser Doppler velocimetry and spectral radiative intensity measurement have been proposed to provide valuable data and improve the modeling analyses.

Ku, Jerry C.↗
DOE OSTI2024

Linac_Gen: Integrating Machine Learning and Particle-in-Cell Methods for Enhanced Beam Dynamics at Fermilab

Here, we introduce Linac_Gen, a tool developed at Fermilab, which combines machine learning algorithms with Particle-in-Cell methods to advance beam dynamics in linacs. Linac_Gen employs techniques such as Random Forest, Genetic Algorithms, Support Vector Machines, and Neural Networks, achieving a tenfold increase in speed for phase-space matching in Linacs over traditional methods, through the use of genetic algorithms. Crucially, Linac_Gen's adept handling of 3D field maps elevates the precision and realism in simulating beam instabilities and resonances, marking a key advancement in the field. Benchmarked against established codes, Linac_Gen demonstrates not only improved efficiency and precision in beam dynamics studies but also in the design and optimization of Linac systems, as evidenced in its application to Fermilab's PIP-II Linac project. This work represents a notable advancement in accelerator physics, marrying ML with PIC methods to set new standards for efficiency and accuracy in accelerator design and research. Linac_Gen exemplifies a novel approach in accelerator technology, offering substantial improvements in both theoretical and practical aspects of beam dynamics.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Linac_Gen: integrating machine learning and particle-in-cell methods for enhanced beam dynamics at Fermilab

Here, we introduce Linac_Gen, a tool developed at Fermilab, which combines machine learning algorithms with Particle-in-Cell methods to advance beam dynamics in linacs. Linac_Gen employs techniques such as Random Forest, Genetic Algorithms, Support Vector Machines, and Neural Networks, achieving a tenfold increase in speed for phase-space matching in linacs over traditional methods through the use of genetic algorithms. Crucially, Linac_Gen's adept handling of 3D field maps elevates the precision and realism in simulating beam instabilities and resonances, marking a key advancement in the field. Benchmarked against established codes, Linac_Gen demonstrates not only improved efficiency and precision in beam dynamics studies but also in the design and optimization of linac systems, as evidenced in its application to Fermilab's PIP-II linac project. This work represents a notable advancement in accelerator physics, marrying ML with PIC methods to set new standards for efficiency and accuracy in accelerator design and research. Linac_Gen exemplifies a novel approach in accelerator technology, offering substantial improvements in both theoretical and practical aspects of beam dynamics.

43 PARTICLE ACCELERATORS↗
DOE OSTI2022

Systematic Errors Induced by Dipole Component Change in Quadrupole Beam-Based Alignment Measurements for Circular Accelerators

Beam-based alignment (BBA) for quadrupole magnets is now a well-established process for circular accelerators to steer beam orbit through the magnetic centers such that beam orbit is not disturbed when the gradients of quadrupoles are changed. At some facilities, the centers estimated from BBA techniques are also used as a proxy for steering beam through the centers of nearby nonlinear magnets to minimize degradation of nonlinear dynamics caused by off-centered orbit. The random errors associated with BBA are well known, but very little attention has been paid to the systematic error generated by a dipole component change, or equivalently a shift in the magnetic center, when the quadrupole strength is varied. The analytical formulas for this error and its amplification factor (potentially a few orders of magnitude) with respect to the magnetic center motion have been derived and confirmed with simulations. We address the significance of this error as well as the part that cannot be estimated from the beam-based measurement alone. Finally, the BBA measurements obtained at NSLS-II and their systematic errors on the order of hundreds of microns are discussed.

43 PARTICLE ACCELERATORS↗
DOE OSTI2023

The mapping & avoidance of high order cavity modes

In this paper a technique developed in 2016 is presented for mapping the multidimensional, multi-mode high order mode landscape of a beam driven super conducting RF cavity. The initial use case for this technique was intended to allow longitudinal gradient control of a beam driven super conducting cavity while simultaneously avoiding many dangerous high order modes and excessive component stresses. This paper will focus on the stability and component stress considerations of the 56MHz superconducting cavity, located in the 4 o’clock sector interaction region of the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory. The 56MHz cavity is intended to work in conjunction with the Stochastic Cooling system to improve the longitudinal confinement in the central 197MHz RF bucket and thus increase the integrated luminosity during heavy ion beam runs at RHIC.

43 PARTICLE ACCELERATORS↗